DSEIGNER RUBY Royale™ Advanced Workshop by Karin Johannesson
Total Page:16
File Type:pdf, Size:1020Kb
DSEIGNER RUBY Royale™ Advanced Workshop By Karin Johannesson Explore some of the top features of the HUSQVARNA VIKING® DESIGNER RUBY Royal™ sewing and embroidery machine and use both sewing and embroidery features to create this purse with a decorative strap. Sewing Supplies; HUSQVARNA VIKING® DESIGNER RUBY Royal ™ sewing and embroidery machine HUSQVARNA VIKING® DESIGNER™ Crown Hoop, 260x200 413116501 HUSQVARNA VIKING® Utility foot A 412764001 HUSQVARNA VIKING® Decorative Stitch Foot B 413113646 HUSQVARNA VIKING® Blindhem Foot D 412380445 HUSQVARNA VIKING® Zipper foot E 412801501 HUSQVARNA VIKING® Sensor Q foot 413192045 HUSQVARNA VIKING® Side Motion Foot S 412795201 INSPIRA® embroidery needle, size 90 620099496 INSPIRA® twin needle, size 80. 2 mm 620104696 INSPIRA® Fusible Fleece, iron on batting 320003996 INSPIRA® Tear-A-Way stabilizer 620112296 INSPIRA® Stick N Fuse 11 for Dimensional Stitches 620133296 Fabric A 14” laminated linen or something similar (outside of bag and strap) Fabric B 14” quilter’s cotton (inside of bag and appliqués) Fabric C 4” cotton, solid color, no print (decorative stitching) Fabric scraps for test sewing decorative stitches etc. 14” of 1⅛” Wide (or slightly wider) webbing (strap) 3”of ⅝” Wide ribbon (strap attachment) 10” (25 cm) zipper One set of key fob hardware (strap attachment) (if you can get hold of this item you could use a D-ring instead) Threads; A selection of embroidery threads for embroidery and decorative stitches, sewing thread for construction and embroidery bobbin fill for embroidery. General sewing supplies: marking pen, pins, embroidery scissors, iron and pliers (to attach the key fob hardware set.) Page 1 of 14 © 2014 KSIN Luxembourg ll, S.ar.l. VIKING , DELUXE, DESIGNER RUBY ROYALE and INSPIRA are trademarks of KSIN Luxembourg ll, S.ar.l. HUSQVARNA is a trademark of Husqvarna AB. All trademarks used under license by VSM Group AB Cut; Make yourself a pattern using the included diagram (pdf file) with measurements. Fabric A 1 pcs according to purse pattern (seam allowance is included) 2”W x 14”L (dimensional stitches on strap) Fabric B 1 pcs according to purse pattern (seam allowance is included) 5” x 5” (design appliqué) 20 pieces 1½” x 1½” (dimensional stitches) Fabric C 4”W x 13”L INSPIRA® Fusible Fleece 1 piece of purse pattern INSPIRA® Tear-A-Way stabilizer 16” L x 12” W 4” W x 13” L 2½” W x 14” L Scrap pieces for test sewing decorative stitches etc. Prepare; • Press the INSPIRA® Fusible Fleece on to the purse fabric A. • Press INSPIRA® Stick N Fuse ll on the wrong side of all small pieces of scrap fabric for Dimensional Stitches. Remove the paper, leaving the glued part on the back side of your fabric pieces. (You can also press the INSPIRA® Stick N Fuse ll to the fabric before cutting the small squares.) Page 2 of 14 © 2014 KSIN Luxembourg ll, S.ar.l. VIKING , DELUXE, DESIGNER RUBY ROYALE and INSPIRA are trademarks of KSIN Luxembourg ll, S.ar.l. HUSQVARNA is a trademark of Husqvarna AB. All trademarks used under license by VSM Group AB Design Appliqué Let’s start with programming the Design Appliqué embroidery file to save it into the machine memory. In the DESINGER RUBY™ Royale sewing and embroidery machine, you have three different stitches and seven different shapes to choose from to create original embroidery appliqués instantly on the screen. 1. Make sure you’re in Embroidery Edit mode 2. Touch My Hoops and select the 120x120 Hoop . (We are not going to embroider with this hoop, but it doesn’t matter which hoop we use when programming. I usually select a hoop that is close to the size of embroidery combination that I’d like to create.) 3. Touch Basic Design Appliqué 4. There are 7 shapes to choose from when creating an appliqué design. The Circle shape is selected by default. We are going to create a heart, so touch on the heart shape. 5. We want the heart to be slightly smaller, so touch the down arrow in the wheel to make it smaller . Set the height of the heart to 110.0. 6. We also want this heart to have a slightly different look. It should be a little bit narrower, so therefore we need to touch the padlock to unlock proportions . 7. Touch the left arrow in the wheel to set the size to 110 x 75 8. We are also going to change the decorative stitch of the appliqué from the default wide satin stitch to the irregular satin stitch which is called “Fur stich”, touch the third stitch to select it. 9. Touch OK Page 3 of 14 © 2014 KSIN Luxembourg ll, S.ar.l. VIKING , DELUXE, DESIGNER RUBY ROYALE and INSPIRA are trademarks of KSIN Luxembourg ll, S.ar.l. HUSQVARNA is a trademark of Husqvarna AB. All trademarks used under license by VSM Group AB Tips! Touch Color block list and zoom in close to the stitches if you’d like to see how this appliqué is built up with three different color blocks. First color block is a placement line, showing you where to put your appliqué fabric. Second color block is a stitch that sews the appliqué fabric in place. After this color block is sewn you should trim away the excess fabric. Third color block is your decorative stitch that covers the raw edges. 10. Touch Save to My Designs 11. Touch Rename . 12. Erase the genereted file name by touch and hold on Delete and type “HEART” 13. Touch OK to confirm your new name. 14. Touch OK to save the file. 15. Touch My Hoops and select the 260x200 Hoop . 16. Make sure the design is centered in the hoop. (If not, just touch the center of the wheel to center it) 17. We are going to add some text on top of the appliqué heart. Touch the Font Menu in the toolbar. 18. Scroll down and select Embroidery Font “Mesa 20” 19. Type the text you want to embroider on your purse.I have embroidred “I’m a limited edition” on my purse. 20. Touch OK to close the text input screen and toggle to embroidery edit. 21. Make sure the text is centered in the hoop. (If not, just touch the center of the wheel to center it) 22. Touch Save to My Designs 23. Touch OK to save the file 24. Touch OK in the pop-up “Replace file?” Page 4 of 14 © 2014 KSIN Luxembourg ll, S.ar.l. VIKING , DELUXE, DESIGNER RUBY ROYALE and INSPIRA are trademarks of KSIN Luxembourg ll, S.ar.l. HUSQVARNA is a trademark of Husqvarna AB. All trademarks used under license by VSM Group AB Create a Side-motion stitch in Prog mode The second file we are going to create and save for later use is a stitch that we will make by using the programming feature in Sewing Mode. We will open a built-in stitch and add some side-motion stitches to create a wider stitch. (We have had this feature built into the Top of the line machines for some years, but a lot of us haven’t been using and promoting this feature much. So therefore I would like to take the opportunity to show you how to create such a stitch.) 1. Make sure you’re in Sewing mode 2. Touch Program to open the window where you can create the stitch. 3. Touch Stitch Menu and select stich M11 4. Touch Duplicate to get another stitch on screen. 5. Touch Mirror Side-to-Side to flip the stitch sideways. 6. Touch the Scroll Up one time to move the cursor up to the position between the two stitches. 7. Touch Stitch Menu and select 8-Way Stitches (menu T). 8. Touch the straight stitch that sews backward and to the right. 9. Change the width 0.3 See how the decorative stitches move together as you change the setting of this stitch. 10. Touch Duplicate , change the width 0.8 11. Touch Duplicate , keep the exact same settings. 12. Touch Duplicate , change the width 1.8 and the length to 1.3. 13. Touch the Scroll Down one time to move the cursor down to the position below the decorative stitch. 14. Touch the straight stitch that sews backward and to the left. 15. Repeat step 9, 10, 11 and 12. 16. Touch OK to toggle to sewing mode and see what the stitch will look like. 17. Touch Save to My Stitches 18. Touch an empty slot to save your stitch in the U-menu. 19. Touch OK Page 5 of 14 © 2014 KSIN Luxembourg ll, S.ar.l. VIKING , DELUXE, DESIGNER RUBY ROYALE and INSPIRA are trademarks of KSIN Luxembourg ll, S.ar.l. HUSQVARNA is a trademark of Husqvarna AB. All trademarks used under license by VSM Group AB Embroidery- and Sewing instruction All the programming is now done and it’s time to start sewing! 1. Attach the embroidery unit and the Sensor Q foot to the machine. 2. Hoop tear away stabilizer in the DESIGNER™ Crown Hoop. 3. Thread the machine with an embroidery bobbin thread in the bobbin. 4. Attach the embroidery hoop to the embroidery unit arm. Design Appliqué 1. Make sure you’re in Embroidery Edit mode 2. Also make sure that you do not have anything selected on screen. If you do, touch and hold on Delete icon to clear the screen 3. Touch My Hoops and select the DESIGNER™ Crown Hoop 260x200 4. Touch File Manager and touch My Designs 5. Touch and hold on the Design Applique design, called HEART, which you saved earlier.