DOCSLIB.ORG

LH1546ADF Datasheet (PDF)

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
LH1546ADF Datasheet (PDF) LH1546ADF, LH1546ADFTR www.vishay.com Vishay Semiconductors 1 Form A Solid-State Relay (Normally Open) FEATURES • Isolation test voltage 5300 VRMS • Typical RON 22 Ω A 1 4 S1 • Load voltage 350 V • Load current 120 mA C 2 3 S2 • Clean bounce free switching • Current limit protection • Low power consumption • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 DESCRIPTION APPLICATIONS The LH1546AD is a single channel solid state relay in a • General telecom switching 4 pin SMD package. It is a SPST normally open switch (1 Form A) that replaces electromechanical relays in many • Metering applications. It is constructed using a GaAlAs LED for • Security equipment actuation control and MOSFET switches for the output. • Instrumentation In addition, it employs current-limiting circuitry to provide • Industrial controls overvoltage protection. • Battery management systems • Automatic test equipment AGENCY APPROVALS • UL1577, file no. E52744 ORDERING INFORMATION SMD LH1546A##TR PART NUMBER ELECTR. PACKAGE TAPE AND VARIATION CONFIG. REEL > 0.1 mm PACKAGE UL SMD-4, tubes LH1546ADF SMD-4, tape and reel LH1546ADFTR Rev. 1.8, 05-Jul-2018 1 Document Number: 83836 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LH1546ADF, LH1546ADFTR www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified) PARAMETER CONDITION SYMBOL VALUE UNIT INPUT IRED continuous forward current IF 50 mA IRED reverse voltage VR 5V Input power dissipation Pdiss 80 mW OUTPUT DC or peak AC load voltage VL 350 V Continuous DC load current at 25 °C, I 120 mA bidirectional L SSR output power dissipation Pdiss 550 mW SSR Ambient temperature range Tamb -40 to +85 °C Storage temperature range Tstg -40 to +150 °C Soldering temperature t = 10 s max. Tsld 260 °C Note • Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. ELECTRICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT INPUT IRED forward current, switch turn-on IL = 100 mA, t = 10 ms IFon -0.252 mA IRED forward current, switch turn-off VL = ± 350 V, IL < 1 μA IFoff 0.05 0.15 - mA IRED forward voltage IF = 10 mA VF - 1.36 1.45 V IRED reverse current VR = 5 V IR - - 10 μA OUTPUT On-resistance, AC/DC: pin 3 (±) to 4 (±) IF = 5 mA, IL = 50 mA RON -2235Ω Off-resistance IF = 0 mA, VL = ± 100 V ROFF 0.5 5000 - GΩ IF = 0 mA, VL = ± 100 V IO - < 1 200 nA Off-state leakage current IF = 0 mA, VL = ± 350 V IO - 6 500 nA IF = 0 mA, VL = 1 V, 1 MHz CO -39-pF Output capacitance pin 3 to 4 IF = 0 mA, VL = 50 V, 1 MHz CO -6-pF Current limit AC/DC IF = 5 mA, t = 5 ms, VL = ± 6 V Ilimit 170 300 450 mA TRANSFER Capacitance (input to output) VIO = 1 V CIO -1-pF Note • Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluations. Typical values are for information only and are not part of the testing requirements. SWITCHING CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Turn-on time IF = 5 mA, IL = 50 mA ton -0.133 ms Turn-off time IF = 5 mA, IL = 50 mA toff -0.053 ms Rev. 1.8, 05-Jul-2018 2 Document Number: 83836 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LH1546ADF, LH1546ADFTR www.vishay.com Vishay Semiconductors Input 1 4 A VL C 2 90 % 3 Output Output 10 % ton toff Fig. 1 - Timing Schematic SAFETY AND INSULATION RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Climatic classification According to IEC 68 part 1 40 / 100 / 21 Pollution degree According to DIN VDE 0109 2 Comparative tracking index Insulation group IIIa CTI 175 Maximum rated withstanding isolation voltage According to UL1577, t = 1 min VISO 5300 VRMS Maximum transient isolation voltage According to DIN EN 60747-5-5 VIOTM 8000 Vpeak Maximum repetitive peak isolation voltage According to DIN EN 60747-5-5 VIORM 890 Vpeak 12 VIO = 500 V, Tamb = 25 °C RIO ≥ 10 Ω Isolation resistance 11 VIO = 500 V, Tamb = 100 °C RIO ≥ 10 Ω Output safety power PSO 600 mW Input safety current ISI 240 mA Safety temperature TS 175 °C Creepage distance ≥ 8mm Clearance distance ≥ 8mm Insulation thickness DTI ≥ 0.4 mm VIORM x 1.875 = VPR, 100 % production test Input to output test voltage, method B VPR 1669 Vpeak with tM = 1 s, partial discharge < 5 pC VIORM x 1.6 = VPR, 100 % sample test Input to output test voltage, method A VPR 1424 Vpeak with tM = 10 s, partial discharge < 5 pC Note • As per IEC 60747-5-5, § 7.4.3.8.2, this optocoupler is suitable for “safe electrical insulation” only within the safety ratings. Compliance with the safety ratings shall be ensured by means of protective circuits. 250 800 200 600 150 400 afety Power afety Power (mW) afety Current (mA) S 100 S 200 50 - Input -Output -Output I S O I S P 0 0 -50 0 50 100 150 -50-250 255075100125150175 ° Tamb - Ambient Temperature ( C) ° Tamb - Ambient Temperature ( C) Fig. 2 - Safety Power Dissipation vs. Ambient Temperature Fig. 3 - Safety Input Current vs. Ambient Temperature Rev. 1.8, 05-Jul-2018 3 Document Number: 83836 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LH1546ADF, LH1546ADFTR www.vishay.com Vishay Semiconductors TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) 2.5 140 IL = 100 mA 120 2.0 100 1.5 80 60 1.0 witch Turn-On witch 40 S - Load Current (mA) L I 0.5 20 for IF > 5 mA Normalized to Tamb = 25 °C 0 Normalized Forward Current 0 -40-200 20406080100 -40-200 20406080100 ° Tamb - Ambient Temperature ( C) ° Tamb - Ambient Temperature ( C) Fig. 4 - Maximum Load Current vs. Ambient Temperature Fig. 7 - Normalized Forward Current for Switch Turn-On vs. Ambient Temperature 1.7 2.0 1.6 IF = 5.0 mA IL = 50 mA 1.5 1.5 tance s i IF = 10 mA s 1.4 1.0 1.3 1.2 IF = 2 mA 0.5 -(V) Voltage Forward I = 5 mA F F V 1.1 Normalized to Tamb = 25 °C Normalized On-Re Normalized 1.0 0 -40-200 20406080100 -40-200 20406080100 ° ° Tamb - Ambient Temperature ( C) Tamb - Ambient Temperature ( C) Fig. 5 - Forward Voltage vs. Ambient Temperature Fig. 8 - Normalized On-Resistance vs. Ambient Temperature 60 60 IF = 0 mA 50 50 f = 1 MHz T = 85 °C 40 40 T = 25 °C 30 30 20 T = -40 °C 20 - Forward Current (mA) 10 (pF) witch Capacitance 10 F S I 0 0 0 0.5 1.0 1.5 2.0 0 102030405060 VF - Forward Voltage (V) Applied Voltage (V) Fig. 6 - Forward Current vs. Forward Voltage Fig. 9 - Switch Capacitance vs. Applied Voltage Rev. 1.8, 05-Jul-2018 4 Document Number: 83836 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LH1546ADF, LH1546ADFTR www.vishay.com Vishay Semiconductors 100 0.20 IF = 0 mA IL = 50 mA T = 85 °C 0.16 T = 85 °C 10 ) s T = 25 °C 0.12 1 T = 25 °C 0.08 0.1 T = -40 °C T = -40 °C Turn-Off Time (m tate Leakage tate Leakage Current (nA) 0.04 S Off- 0.01 0 0100200300 0 1020304050 VL - Load Voltage (V) IF - Forward Current (mA) Fig. 10 - Off-State Leakage Current vs. Load Voltage Fig. 13 - Turn-Off Time vs. Forward Current 2.0 2.0 IL = 50 mA 1.8 1.6 IF = 5.0 mA ) 1.5 s T = 85 °C 1.4 1.2 1.0 1.0 0.8 T = 25 °C 0.6 0.5 Turn-On(m Time T = -40 °C 0.4 Normalized Turn-Off Time Turn-Off Normalized 0.2 Normalized to Tamb = 25 °C 0 0 0 1020304050 -40 -20 0 20 40 60 80 100 ° IF - Forward Current (mA) Tamb - Ambient Temperature ( C) Fig. 11 - Turn-On Time vs. Forward Current Fig. 14 - Normalized Turn-Off Time vs. Ambient Temperature 2.0 1.8 1.6 IF = 5 mA 1.4 1.2 1.0 0.8 0.6 0.4 Normalized Turn-On Turn-On Time Normalized 0.2 Normalized to Tamb = 25 °C 0 -40 -20 0 20 40 60 80 100 ° Tamb - Ambient Temperature ( C) Fig. 12 - Normalized Turn-On Time vs. Ambient Temperature Rev. 1.8, 05-Jul-2018 5 Document Number: 83836 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 LH1546ADF, LH1546ADFTR www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters SMD-4 9.80 ± 0.25 7.62 typ.
Load more

Recommended publications
  • Aras Innovator - Connectors Support Matrix
    Aras Innovator - Connectors Support Matrix MCAD Tools Autocad Autodesk Inventor CATIA V5 Dassault CATIA V6 SolidWorks Creo PTC Creo Direct NX Siemens Solid Edge PDM/PLM Autodesk Vault Altium Vault Enovia Dassault SmarTeam SolidWorks PDM Pro Oracle Agile PTC Windchill SAP PLM Siemens Teamcenter SAP PLM ERP IBM DOORS ORACLE ERP ERP SAP ERP V6 ERP HANNA QAD QAD/Mfg Dynamics NAV Microsoft Dynamics GP Dynamics AX Oracle Netsuite BIM Tools Revit AutoDesk 1 January 2021 Aras Innovator - Connectors Support Matrix ECAD Tools AutoCAD Electrical (Autodesk) Electrical CAD AutoDesk AutoCAD Electrical (Autodesk) Electrical Librarian SolidWorks (Dassault) Electrical Dassault SolidWorks (Dassault) Electrical Librarian Designer Electronic Board Layout CAD Designer Electronic Schematic CAD Designer Electronic Librarian Altium Nexus Server Agent Nexus Electronic Librarian Concord Electronic Librarian Concord PCB Electronic Librarian Xpedition Capture (Mentor Graphic) Electronic Schematic CAD PADS Standard Electronic Schematic CAD Xpedition Electronic Board Layout CAD PADS Standard Electronic Board Layout CAD Xpedition & PADS Professional Electronic Librarian PADS Standard Electronic Librarian Mentor PADS Professional Electronic Schematic CAD PADS Professional Electronic Board Layout CAD Capital Electrical Capital Electrical Librarian EDM Server Agent EDM Librarian Allegro HDL Electronic Schematic CAD OrCAD Capture CIS Electronic Schematic CAD Cadence Allegro & OrCAD Electronic Board Layout CAD Allegro HDL Electronic Librarian OrCAD Electronic Librarian Zuken E3.series (Zuken) Electrical Wiring Layout CAD Elcad Electrical CAD Elcad Electrical Librarian Aucotec Engineering Base Electrical CAD Engineering Base Electrical Librarian EPLAN Electric Electrical CAD EPLAN EPLAN Electric Electrical Librarian Pulsonix Electronic Board Layout CAD Pulsonix Pulsonix Electronic Schematic Layout CAD Pulsonix Electronic Librarian 2 January 2021.
    [Show full text]
  • Electronic Design Automation Tools Part 2 by Christopher Henderson This Article Provides an Overview of the Electronic Design Automation (EDA) Design Tools
    Issue 126 December 2019 Electronic Design Automation Tools Part 2 By Christopher Henderson This article provides an overview of the Electronic Design Automation (EDA) design tools. The EDA industry is an interesting ecosystem and bears discussing, so that the design engineer can Page 1 Electronic Design understand the environment. Automation Tools In last month’s feature article we discussed the three major EDA Part 2 tool suppliers: Cadence Design Systems, Synopsys, and Mentor Graphics, which is now owned by Siemens. Here in Part II we will Page 5 Technical Tidbit briefly discuss interoperability issues between the three major platforms. We’ll also discuss other suppliers developing tools in this area. Finally, we’ll discuss the use case and the strengths and Page 8 Ask the Experts weaknesses of the tool suites. Each of the three major EDA firms creates products that work well within their own portfolio, but what about across the three major Page 10 Spotlight providers? What if you want to create designs using tools from across two or more of the providers? This is a major challenge because it requires that one work with different formats for different files, which Page 13 Upcoming Courses requires translators, scripts and additional programs. What would be most useful is a good interoperability standard, and the good news is that there is one. It is called OpenAccess and is supported and promoted by the Silicon Integration Initiative. OpenAccess actually had its start as the result of a lawsuit against Cadence. Users sued Cadence, claiming that their internal format gave them a controlling monopoly in the design area, and a judge agreed with them.
    [Show full text]
  • 233-203 PCB Terminal Block; Push-Button; 0.5 Mm²; Pin Spacing 2.5 Mm; 3-Pole; CAGE CLAMP®; 0,50 Mm²; Gray
    Data sheet | Item number: 233-203 PCB terminal block; push-button; 0.5 mm²; Pin spacing 2.5 mm; 3-pole; CAGE CLAMP®; 0,50 mm²; gray www.wago.com/233-203 Color: L = (pole no. x pin spacing) + 2.3 mm SubjectItem description to changes. Please also observe the further product documentation! WAGO Kontakttechnik GmbH & Co. KG Do you have any questions about our products? Hansastr. 27 We are always happy to take your call at +49 (571) 887-44222. 32423 Minden Phone: +49571 887-0 | Fax: +49571 887-169 Email: [email protected] | Web: www.wago.com 03.07.2020 Page 1/8 Data sheet | Item number: 233-203 www.wago.com/233-203 Item description Compact PCB terminal strips with CAGE CLAMP® connection and screwdriver actuation parallel or perpendicular to conductor entry Double solder pins for high mechanical Custom color combinations Data Electrical data Ratings per IEC/EN 60664-1 Ratings per IEC/EN 60664-1 Nominal voltage (III/3) 63 V Rated surge voltage (III/3) 2.5 kV Rated voltage (III/2) 160 V Rated surge voltage (III/2) 2.5 kV Nominal voltage (II/2) 320 V Rated surge voltage (II/2) 2.5 kV Rated current 6 A Legend (ratings) (III / 2) ≙ Overvoltage category III / Pollution degree 2 Approvals per UL 1059 Rated voltage UL (Use Group B) 150 V Rated current UL (Use Group B) 4 A Approvals per CSA Rated voltage CSA (Use Group B) 150 V Rated current CSA (Use Group B) 4 A Connection data Connection technology CAGE CLAMP® Actuation type Push-button Solid conductor 0,08 … 0,5 mm² / 28 … 20 AWG Fine-stranded conductor 0,08 … 0,5 mm² / 28 … 20 AWG Fine-stranded conductor; with insulated ferrule 0,25 mm² Fine-stranded conductor; with uninsulated ferrule 0,25 mm² SubjectStrip length to changes.
    [Show full text]
  • Pulsonix Users Guide Pulsonix Users Guide 3
    Pulsonix Design System Users Guide 2 Pulsonix Users Guide Pulsonix Users Guide 3 Copyright Notice Copyright ã WestDev Ltd. 2001-2018 Pulsonix is a Trademark of WestDev Ltd. All rights reserved. E&OE Copyright in the whole and every part of this software and manual belongs to WestDev Ltd. and may not be used, sold, transferred, copied or reproduced in whole or in part in any manner or in any media to any person, without the prior written consent of WestDev Ltd. If you use this manual you do so at your own risk and on the understanding that neither WestDev Ltd. nor associated companies shall be liable for any loss or damage of any kind. WestDev Ltd. does not warrant that the software package will function properly in every hardware software environment. Although WestDev Ltd. has tested the software and reviewed the documentation, WestDev Ltd. makes no warranty or representation, either express or implied, with respect to this software or documentation, their quality, performance, merchantability, or fitness for a particular purpose. This software and documentation are licensed 'as is', and you the licensee, by making use thereof, are assuming the entire risk as to their quality and performance. In no event will WestDev Ltd. be liable for direct, indirect, special, incidental, or consequential damage arising out of the use or inability to use the software or documentation, even if advised of the possibility of such damages. WestDev Ltd. reserves the right to alter, modify, correct and upgrade our software programs and publications without notice and without incurring liability. Microsoft, Windows, Windows NT and Intellimouse are either registered trademarks or trademarks of Microsoft Corporation.
    [Show full text]
  • Pulsonix PCB Design
    Pulsonix PCB Design Effortless PCB Layouts Pulsonix PCB Layout Construction Lines Pulsonix provides an expert design environment to get your boards Unique to Pulsonix, construction lines provide user-definable 'guide' produced fast with as little effort as possible.With unparalleled ease lines within your design. Use construction lines to create complex of use, Pulsonix provides a feature-rich toolset to get the job done board outlines or design items and to align irregular shapes.With efficiently. Everything in Pulsonix is logical, easy to setup and easy to their own layer, colour and style, construction lines are valuable for all use. Even complex design constraint rules can be easily defined using 2D creation without the need to import complex shapes from highly accessible dialogs. outside of your PCB design environment. Technology files for fast start-up True Mixed Technology Support Just like templates used for other desktop products, Pulsonix has a Technology is supported for standard plated through holes, surface unique system of technology files for fast start-up. Customise and mount devices/technologies, blind and buried vias and laser/plasma pre-define items such as Design rules, Layers, Materials, Spacing rules drilled micro-vias. Pads with slots or non-round holes are easily and Copper/Thermal rules as well as styles for text, tracks, pads, lines achieved using standard pad style definitions or custom pad shapes. to name a few. Company standards can be created in one file then used and shared by all Pulsonix users.Technology files can be created and updated as you design to create a master file containing all your design settings.
    [Show full text]
  • Pulsonix Design System V11.0 Update Notes
    Pulsonix Design System V11.0 Update Notes 2 Pulsonix Version 11.0 Update Notes Copyright Notice Copyright ã WestDev Ltd. 2000-2021 Pulsonix is a Trademark of WestDev Ltd. All rights reserved. E&OE Copyright in the whole and every part of this software and manual belongs to WestDev Ltd. and may not be used, sold, transferred, copied or reproduced in whole or in part in any manner or in any media to any person, without the prior written consent of WestDev Ltd. If you use this manual you do so at your own risk and on the understanding that neither WestDev Ltd. nor associated companies shall be liable for any loss or damage of any kind. WestDev Ltd. does not warrant that the software package will function properly in every hardware software environment. Although WestDev Ltd. has tested the software and reviewed the documentation, WestDev Ltd. makes no warranty or representation, either express or implied, with respect to this software or documentation, their quality, performance, merchantability, or fitness for a particular purpose. This software and documentation are licensed 'as is', and you the licensee, by making use thereof, are assuming the entire risk as to their quality and performance. In no event will WestDev Ltd. be liable for direct, indirect, special, incidental, or consequential damage arising out of the use or inability to use the software or documentation, even if advised of the possibility of such damages. WestDev Ltd. reserves the right to alter, modify, correct and upgrade our software programs and publications without notice and without incurring liability.
    [Show full text]
  • EMBEDDING TECHNOLOGY – DIE GRUNDLAGEN Aus Teil 1: Varianten Der Einbetttechnologie
    Die Welt der eingebetteten Bauteile in Leiterplatten Teil 2 – Layout und Applikationsbeispiele Jürgen Wolf Würth Elektronik GmbH & Co. KG Circuit Board Technology Advanced Solution Center IHR REFERENT ▪ Jürgen Wolf Dipl.-Ing. Mikrosystemtechnik ▪ Leiter Advanced Solution Center − Verantwortlicher für die Technologie zum Einbetten von Bauteilen/Funktionen in die Leiterplatte und für dehnbare Leiterplatten (STRETCH.flex) − Unterstützung Vertrieb für die Einbetttechnologie und neue Technologien − Qualifizierung, Planung und Weiterentwicklung der Technologien Speichern Sie meine ▪ Seit 2008 bei Würth Elektronik CBT Kontaktdaten direkt in Ihrem Adressbuch! 2 AGENDA 1 Kurze Zusammenfassung aus Teil 1 – Grundlagen 2 Übersicht EDA-Tools und deren Möglichkeiten 3 Layouten von Leiterplatten mit eingebetteten Komponenten 4 Applikationsbeispiele 3 AGENDA 1 Kurze Zusammenfassung aus Teil 1 – Grundlagen 2 Übersicht EDA-Tools und deren Möglichkeiten 3 Layouten von Leiterplatten mit eingebetteten Komponenten 4 Applikationsbeispiele 4 EMBEDDING TECHNOLOGY – DIE GRUNDLAGEN Aus Teil 1: Varianten der Einbetttechnologie MICROVIA.embedding SOLDER.embedding FLIP-CHIP.embedding Nacktchips, SMD Gebumpte spezielle R`s und C`s Bauelemente Nacktchips montiert auf Innenlage oder gelötet auf montiert auf Cu-Folie Innenlage Innenlage elektrischer Kontakt durch elektrischer Kontakt durch Lot elektrischer Kontakt durch ACA Microvias hohe Zuverlässigkeit hohe Zuverlässigkeit höchste Zuverlässigkeit Klein-, Mittel- und Klein-, Mittel- und Großserien Großserien Großserien
    [Show full text]
  • Strong Business Fundamentals To
    Delivering Strong Performance & Building Momentum for Future Growth Altium Full Year Investor Presentation Aram Mirkazemi CEO 25-28 August 2015 Richard Leon CFO Sydney & Melbourne Kim Besharati VP IR Disclaimer This presentation has been prepared by Altium Limited (ACN 009 568 772) Future performance - Forward looking statements, opinions and estimates and is for information purposes only. It does not constitute financial product or provided in this presentation are based on assumptions and contingencies investment advice or a recommendation to acquire Altium shares and has which are subject to change without notice, as are statements about market been prepared without taking into account the objectives, financial situation or and industry trends, which are based on interpretations of current market needs of individuals. Before making an investment decision prospective conditions. Forward looking statements including projections, guidance on investors should consider the appropriateness of the information having regard future earnings and estimates are provided as a general guide only and should to their own objectives, financial situation and needs and seek legal and not be relied upon as an indication or guarantee of future performance. An taxation advice appropriate to their jurisdiction. Altium is not licensed to investment in Altium shares is subject to investment and other known and provide financial product advice in respect of Altium shares. unknown risks, some of which are beyond the control of Altium Limited. No representation or warranty, express or implied, is made as to the fairness, Altium, Altium Designer, Altium Vault, Ciiva, Circuitmaker, Circuistudio, accuracy, completeness or correctness of the information, opinions and Octopart, PCBWorks, Protel and Tasking, and their respective logos, are conclusions contained in this presentation.
    [Show full text]
  • Data Sheet | Item Number: 237-136 PCB Terminal Block; 2.5 Mm²; Pin Spacing 5 Mm; 6-Pole; 2,50 Mm²; Gray
    Data sheet | Item number: 237-136 PCB terminal block; 2.5 mm²; Pin spacing 5 mm; 6-pole; 2,50 mm²; gray www.wago.com/237-136 Color: Data Electrical data Ratings per IEC/EN 60664-1 Ratings per IEC/EN 60664-1 Rated voltage (III / 2) 250 V Rated impulse voltage (III / 2) 2.5 kV Rated current 16 A Legend (ratings) (III / 2) ≙ Overvoltage category III / Pollution degree 2 Approvals per UL 1059 Approvals per UL 1059 Subject to changes. Please also observe the further product documentation! WAGO Kontakttechnik GmbH & Co. KG Do you have any questions about our products? Hansastr. 27 We are always happy to take your call at +49 (571) 887-44222. 32423 Minden Phone: +49571 887-0 | Fax: +49571 887-169 Email: [email protected] | Web: www.wago.com 24.04.2020 Page 1/5 Data sheet | Item number: 237-136 www.wago.com/237-136 Connection data Connection technology Screw clamp connection Actuation type Operating tool Solid conductor 0.5 … 2.5 mm² / 20 … 14 AWG Fine-stranded conductor 0.5 … 2.5 mm² / 20 … 14 AWG Strip length 5 … 7 mm / 0.2 … 0.28 inch Conductor entry angle to the PCB 0 ° No. of poles 6 Total number of connection points 6 Total number of potentials 6 Number of connection types 1 Number of levels 1 Geometrical Data Pin spacing 5/5.08 mm / 0.197/0.2 inch Width 5 mm / 0.197 inch Height from the surface 11 mm / 0.433 inch Depth 9 mm / 0.354 inch PCB contact PCB contact THT Solder pin arrangement over the entire terminal strip, in line Number of solder pins per potential 1 Material Data Color gray Material group I Insulating material Polyamide 66 (PA 66) Flammability class per UL94 V0 Clamping spring material Chrome nickel spring steel (CrNi) Contact material Electrolytic copper (E ) Cu Contact plating tin-plated Weight 5.7 g Subject to changes.
    [Show full text]
  • Why You Should Ask for Gerber X2 Files
    Why you should ask for Gerber X2 files The benefits of the Gerber X2 format X2 adds intelligence to the Gerber format by its use of attributes. When loading a new job, attributes allows the CAM software to put the layers directly in the correct position in the stack-up. Other attributes identify the via pads, the SMD pads and so on. This saves plenty of CAM time and effort. As X2 is compatible - the image is not affected by the attributes - the risks are negligible. The benefits are best illustrated by the Gerber X2 intro movie . CAD systems - KiCAD, Pulsonix, Easy-PC, DipTrace and Altium - can now generate Gerber X2 files. We cooperated with the CAD vendors to validate their X2 output. We have sample files from each software available for download. Please check out the samples and see the benefits for yourself. Note that all recent Ucamco software takes advantage of the attributes. If you like the efficiency of X2 then you will want to receive as much X2 files as possible. You now probably receive very few. The CAD systems supporting X2 are there, and Altium is a big one, that is not the issue. CAD operators are reluctant to send out X2 files because they do not know that you accept X2 and prefer X2. Tell them! Gerber X2 files will make your data input faster and more secure. It shows you are following the latest technology. Being first with X2 gives you an advantage over competitors who’s CAM software does not yet support X2 – it is not often one can differentiate by the input format.
    [Show full text]
  • Version 2018.09 NEW / ENHANCED: • Small Outline L-Lead (SOL) O
    Version 2018.09 NEW / ENHANCED: Small Outline L-Lead (SOL) o Added a 10 and 12 pin version Library Editor: o When selecting Create New Row, the new columns “Mounting Type” and “Part Status” are automatically added . Mounting Type = Surface Mount or Through-hole . Part Status = Active or Obsolete (Not Recommended for New Designs = Obsolete) FIXED: Calculator: o Vertical Header: Fixed an issue where selecting the Center of Pins origin feature did not work correctly o PSON with Tab: Removed an unnecessary warning message Library Editor: o Fixed a bug where the program throws an Exception Error when the Find feature stays active when opening multiple FPX files 3D STEP: o QFN: Fixed an issue with the 90 degree Wrap Around Lead model o SOP: Fixed an issue where the Body Cavity and Polarity Marker were not filling in properly OrCAD PCB: o Fixed a .bat command line from Allegro –orcad to Allegro -product OrCAD_PCB_Editor_basics Altium: o Fixed a problem that was drawing two identical Keep Out All shapes CR-5000/CR-8000: o Fixed a crash bug with CR-5000 pad stacks which have more than one area of paste mask Version 2018.08 NEW / ENHANCED: Altium: o Added the ability to create and focus a temporary component before building the specified footprints. This temporary component will delete and re-focus after footprints are built. o Rather than Create the Component directly, a new function called CreateAComponent has been added. This function will check if there is a currently existing component of that name and remove it and all of its primitives.
    [Show full text]
  • Pulsonix Change Notes Version 8.5 Build 5907
    Pulsonix Change Notes These notes list the main functional changes and problem fixes in each release of the software. They are listed in order, latest first. Version 8.5 Build 5907 : 03-May-2016 Functional changes None. Problems Fixed CAM/Plot Gerber - Output was wrongly affected by "Layer Class Break Shape" settings. All Outputs - Width change on last segment of a track was being plotted with an incorrect size. Problem was introduced by a fix in the previous patch. LPKF - Some D codes were missing which resulted in thin lines being output. Version 8.5 Build 5906 : 22-Apr-2016 Functional changes Design Rule Check New check to analyse copper shapes containing cutouts to trap potential Gerber faults. PLM Interface New command in PLM interface for retrieving info about whole components. The ‘GetParts’ command now includes the description. Addition of part description to the report file used by PLM interface. Problems Fixed CAM/Plot Gerber - Program aborts when pad paste shape was reduced to nothing. Gerber - Plot of a top layer in a panel design had missing pads. Gerber - Had a problem with output of very shallow arc. Gerber A segment of track was missing in a particular output Gerber - Output was ignoring via pads touching the edge of poured copper so they were embedded into copper. Gerber - Failed on output of a power plane layer that had a poured template. Gerber - Had different result for drill holes included in output due to changes in back-off settings. Gerber - Necked tracks were sometimes output with the wrong width. Copyright © 2001-2016 WestDev Ltd All trademarks acknowledged to their rightful owners.
    [Show full text]