DOCSLIB.ORG

Heavy Duty 6' Work Bench

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Heavy Duty 6' Work Bench Heavy Duty 6’ MODEL NUMBER Work Bench MRWB - 6 Heavy Duty Work Bench MRWB-6 3 Shelf 2 Drawer - 60”h x 24”d x 72”w Description Qty. Part Number Part Size Long Post 2 RUPT6002 60” Brace 4 RWBE2303 24” Beam 5 RWBE7103 72” Short Post 2 RUPT3602 36” Shelf Support 2 RWSB2801 N/A Top Shelf Beam 1 RWSS8903 N/A Drawer Mount 2 RWDM2305 N/A Drawer Slide 4 RWDS2003 N/A Drawer Shelf Braces 4 RWDB3102 32” Peg Board 1 PGBD7120 20” x 72” Wood Shelf 2 RLPB2472 24” x 72” Center Bracket 2 RWBR0303 N/A Center Drawer Mount 2 RWDM2303 N/A Peg Board Bracket 2 RWPB0401 N/A Wood Drawer Shelf 2 RPB23217 32” x 17” Wood Top Shelf 1 RPB2729 9” x 72” Hardware 12 NB12 #10-24 Safety Instructions These units should be placed on a level surface. Failure to do so can result in poor product performance or create a possible safety hazard. This unit should be securely anchored to a wall or floor with suitable fasteners, which are not included. Do not use this unit for anything other than the manufactures intended purpose. DO NOT STAND ON ANY PART OF THE UNIT, OR USE IT AS A LADDER. Evenly distribute the weight on each level and always keep the heavier loads on the bottom. Use care when working with metal parts. General Instructions Assembly is done with the rivets of the beams and braces fitting into the slots of the post. A rubber mallet may be used on the beams and braces to seat the rivets properly. A hammer can also be used, providing one uses a cloth or a block of wood between the hammer head and the parts to prevent damage. Tap gently and be sure the rivets are straight and fully engaged. Should you have any comments, damage, missing parts, or problems with assembly of this unit please feel free to contact our Edsal manufacturing facility at, (773) 475-3000 and request customer service. We can Consumer Products Division also be reached on the internet at the following email address : [email protected]. Edsal Manufacturing Company 4400 South Packers Avenue To obtain replacement parts, please provide the following information : Chicago, IL 60609 www.edsal.com - Model # - Part # & Description - Location Purchased - Date Purchased Assembly Instructions for MRWB - 6 Post are directional. Tap Lightly 72” Beam (Bend facing down) Step The slot must point Step Peg Board Brackets down. Top Shelf Beam 1 Shelf Ledge Up 2 Long Post Skip Hole From Bottom Figure A 24” Brace Peg Board Bracket Shelf Support Drawer Mount Center Mounting Drawer Slides Bracket Drawer Slide Shelf Support Short Post Center Drawer Mount 72” Beams Take two (2) 24” braces with the shelf ledge facing up, and Take four (4) 72” beams with the bend facing up, and attach one (1) short 36” post and attach rivets from the brace to the the rivets even with the braces from the two end assembly's, top two (2) holes of the short post. Take one (1) long 60” and tap down to seat. Install the top shelf beam and one (1) post and attach the opposite end of the brace to the holes of 72” beam with the bend facing down, to the top holes of the the long post so the brace is level, tap down brace to seat. back posts. Next install a peg board bracket to the beam of Attach the bottom brace to the short post skipping one (1) the top assembly using the nuts and bolts provided. Assem- hole from the bottom and the opposite end to the long post, ble the center drawer assembly by taking a peg board bracket, tap down brace to seat. Take one (1) drawer mount and skip one (1) shelf support, and one (1) center mounting bracket one (1) hole from the top brace and attach rivets to the and bolt them to the work surface back beam (see figure A). short and long post, tap down drawer mount to seat. take Next bolt the shelf support bracket, and the last center mount- one (1) drawer slide and insert it into the slide of the drawer ing bracket to the opposite beam. Attach the two (2) center mount. Repeat this step for the opposite end assembly. drawer mounts by placing the rivets into the holes of the cen- ter mounting brackets. Insert the drawer slides into the center drawer mount slides. Add the final shelf support to the bot- tom two (2) beams using the nuts and bolts provided. Step 4th Hole Down Step 3 4 Peg Board 32” Drawer Shelf Braces (Bend facing down) (Back of drawer slides also) Place the peg board to the inside of the back post of the work Add the wood shelves to the top shelf support, the draw- bench. Using the fourth hole from the top of the back post, ers, the bottom shelf, and the work surface to finalize the align the holes of the peg board to the holes on the back assembly of the workbench. post, and fasten using the nuts and bolts provided. Align the holes on the peg board brackets to the holes of the peg board, and fasten the peg board to the peg board brackets using the nuts and bolts provided. Take the four (4) 32” drawer shelf braces and with the shelf ledge facing down, insert the two (2) rivets into the two (2) holes located on the drawer slides. .
Load more

Recommended publications
  • TOOLS and EQUIPMENT Orthotic 561
    TOOLS AND EQUIPMENT Orthotic 561 Tools Shoe Stretchers............................562 Brannock Measuring Device..................562 Mixing Bowls ..............................562 Aluminum Cast Mandrels ....................562 Laminating Fixtures.........................563 Vises and Yates Clamps.................563-564 Measuring Devices .....................564-567 Hex Sets and Balldrivers.................567-569 Screw and Drill Gages ......................569 Cutting Nippers ............................570 Plastering Tools............................571 Shears and Scissors ....................571-572 Blades, Knives and Surforms .............572-575 Rivets, Punch Sets and Eyelets ...........576-579 Reamers .................................579 Needle Kit ................................579 Deburring Tool.............................579 Rout-A-Burr ...............................579 Precision Oiler.............................580 Countersinks ..............................580 Adjustable Bits.............................580 Tools Ball Set Tool . 580 Micro Torches and Heat Guns ............580-582 Cast Spreaders and Cutters ..............583-584 Alignment Fixtures .........................584 Benders and Contouring Iron .............584-585 Equipment Carvers, Cutters and Routers.............585-588 Sanding Accessories............ 589-591, 601-603 Sewing and Patching Machines ...............592 Drill Press ................................593 Band Saws . .594-595 Dust Collectors ........................596-597
    [Show full text]
  • HYTORC Tool Basics Description, Operation and Safety
    HYTORC Tool Basics Description, Operation and Safety November 10, 2017 BOSS Training Series Basic Operation and Safety Series Contents 1. Hydraulic Torque Tools 2. Pneumatic Torque Tools 3. Electric Torque Tools 5. Hydraulic Tensioners Hydraulic Torque Technology Pneumatic Torque Tool Overview Electric Torque Tool Overview Hydraulic Tensioner Technology Hydraulic Torque Tool Overview Pneumatic Tool Comparison Electric Tool Comparison Top Side Tensioners Hydraulic Tool Comparison JGUN SINGLE SPEED FLASH 2.0 Wind and Subsea Tensioners EDGE jGUN DUEL SPEED LITHIUM SERIES Gun Tensioner Pumps VERSA FRL LION GUN Tensioner Accessories MXT Digital jGUN XLCT L – Lithium Battery Gun T - Hydraulic Tensioning ICE J - jGUN Tool Operating Operating Procedures Operating Procedures AVANTI Procedures STEALTH DJ – Digital jGUN Operating HY-115/230 Procedures HY-Air 4. HYTORC Fasteners Vector 6. Safety HYTORC Washer Additional Hydraulic Pumps Bolting Safety Moment HYTORC Nut H - Hydraulic Torque Tool HW - HYTORC Washer Install Operating Procedures Procedure HN – HYTORC Nut Install Procedure 1. Hydraulic Torque Tools BOSS Training Series Basic Operation and Safety Series Hydraulic Torque Tool Technology PUSH – ADVANCE – CLICK – RELEASE – Tool Drive Turns 24 degrees PUSH Pushing the advance button on the remote PUSH switches a solenoid valve on the pump and directs hydraulic fluid pressure into the advance side of the tool cylinder. ADVANCE ADVANCE Piston in the tool cylinder advances to turn the ratchet 24 degrees/click. (some tool ratchets are different, the STEALTH turns 18 degrees/click) CLICK CLICK Ratchet locks in place against a pawl with a distinct clicking sound. RELEASE - RETRACT Releasing the advance button causes the RELEASE solenoid valve to direct pressure in the release port to retract the piston.
    [Show full text]
  • 60" Workbench
    Owner’s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference. ITEM 69054 60" Workbench Visit our website at: http://www.harborfreight.com Email our technical support at: [email protected] When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-800-444-3353 as soon as possible. Copyright© 2012 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product. any shape or form without the express written consent of Harbor Freight Tools. Failure to do so can result in serious injury. Diagrams within this manual may not be drawn proportionally. Due to continuing SAVE THIS MANUAL. improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included. Table of Contents Safety ......................................................... 2 Parts List and Diagram .............................. 10 Specifications ............................................. 3 Warranty .................................................... 12 Setup .......................................................... 3 SA F ET Y WARNING SYMBOLS AND DEFINITIONS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
    [Show full text]
  • YJ Hood Louver Cut Template
    Poison Spyder Customs, Inc. YJ Hood Louver Cut Template OPTIONAL CUT LINE OPTIONAL CUT LINE At these hole locations: Drill through At these hole locations: Drill through inner brace, then hole-saw nut O O O O inner brace, then hole-saw nut access hole from underside access hole from underside (Step 12) (Step 12) STANDARD STANDARD CUT LINE CUT LINE S S S S S O S O O S S O Existing Windshield Existing Windshield Loop Holes (Step 3) Loop Holes (Step 3) Drill/Hole Saw Locations S O S O (Steps 4 & 6) S O S O drilling, as the sheetmetal is very thin and may want to “catch” on th saw. At some of the optional hole location,s the underside hood brace lies S O directly underneath. While it is OK to drill through the underside brace with S O the hole saw’s pilot bit, try not to saw through it with the hole saw itself. Saw through only the outer sheetmetal, leaving the underside hood brace as untouched as possible at this point. e hole 7. Use a marker to draw a cut line around each of the hole cut-outs as shown in Thank you for purchasing a Poison Spyder Hood Louver for your Jeep. the template, by linking the outside edges of the 1” holes. Installation is fairly simple with the right tools and good mechanical abilities. If you 8. Use your cutting tool of choice to cut along the cut lines made in the previous are not confident in your mechanical skills, please seek the help of a professional Existing Windshield step.
    [Show full text]
  • Manual Drills ​(Brace Drill, Eggbeater Drill)
    Manual Drills (Brace drill, Eggbeater drill) ​ Identify: Head, Handle, Chuck, Bits (drill and screw bits, which are inserted into the chuck) Accompanying Tools: Clamps (usually at least 2), Goggles Safety: ● Wear eye protection ● Clamp material to be drilled securely to a heavy object, with clamps on opposite ends of the wood ● Be cautious of delicate drill bits ● Lay drill carefully on its side when not in use, with bits aimed in from edge of table Operation for drilling holes: ● Clamp material down, with protective layer between material and table if necessary. A second piece of wood is usually sufficient. ● Insert correct bit or choose drill that has correct bit. Chuck is twisted counter-clockwise to loosen jaws that hold bit, clockwise to tighten ● Identify depth of material, hold drill bit on the side of the clamped wood to see how deep it will go, and to ensure that it won’t go into the table. ● Make dot or X on top of wood where hole is to be drilled. ● Hold operating handle with dominant (drawing) hand, other hand holds head or top handle in place. For ambidextrous tinkerers, whichever hand position feels most comfortable to them. ● Rotate handle clockwise to drill into wood. For brace drill, this is a horizontal turning, for eggbeater drill, it is vertical. ● While bit is in wood, do not let go of drill and avoid wiggling. This can break the bit. ● Binding debris can cause overheating of the bit, or make turning the drill difficult. Back out bit and clear debris as necessary ● Back out bit after the desired depth is achieved.
    [Show full text]
  • Hans Brunner Tool Auctions September 15, 2012
    Hans Brunner Tool Auctions September 15, 2012 PO Box 5238, Brassall Qld 4305 www.hansbrunnertools.gil.com.au 07 3294 8253 Vol 22 1 1 Very rare 14” bronze–framed eggbeater drill. George Langford’s excellent type study on Millers Falls #2 drills lists this drill as the first model or type N. It has all the Millers Falls features found in the malleable iron models, most noticeably the wrap-around 2 frame that protects the main gear. Very few of these drills have changed hands which makes any type study a work in progress. To the best of my knowledge only 3 of these are documented, this one included! The patented 2 Superb little steel hand drill, maybe a dental Almond chuck used was patented in 1876, a or a surgical tool. Chrome plated with rosewood date that would fit in with the Millers Falls crank handle. 7” long, no maker’s mark. Plating is history as well as research that suggests a very good with just a few blank spots. G+ $ 60-120 starting date of 1878 for the famous # 2 drill. Whether Millers Falls made them, had them 3 Possibly the most attractive hand drill ever made: Whitney patent made or copied them might eventually be 10 ½” drill marketed by Tower and Lyon, New York N.Y. - the same company determined if more examples come to light but that sold the equally attractive Chaplin’s patent planes. There are no I would not hold my breath! G+ $ 250-500 markings on the drill, just those gorgeous red and gold decorations (striping) on all sides.
    [Show full text]
  • 1. Hand Tools 3. Related Tools 4. Chisels 5. Hammer 6. Saw Terminology 7. Pliers Introduction
    1 1. Hand Tools 2. Types 2.1 Hand tools 2.2 Hammer Drill 2.3 Rotary hammer drill 2.4 Cordless drills 2.5 Drill press 2.6 Geared head drill 2.7 Radial arm drill 2.8 Mill drill 3. Related tools 4. Chisels 4.1. Types 4.1.1 Woodworking chisels 4.1.1.1 Lathe tools 4.2 Metalworking chisels 4.2.1 Cold chisel 4.2.2 Hardy chisel 4.3 Stone chisels 4.4 Masonry chisels 4.4.1 Joint chisel 5. Hammer 5.1 Basic design and variations 5.2 The physics of hammering 5.2.1 Hammer as a force amplifier 5.2.2 Effect of the head's mass 5.2.3 Effect of the handle 5.3 War hammers 5.4 Symbolic hammers 6. Saw terminology 6.1 Types of saws 6.1.1 Hand saws 6.1.2. Back saws 6.1.3 Mechanically powered saws 6.1.4. Circular blade saws 6.1.5. Reciprocating blade saws 6.1.6..Continuous band 6.2. Types of saw blades and the cuts they make 6.3. Materials used for saws 7. Pliers Introduction 7.1. Design 7.2.Common types 7.2.1 Gripping pliers (used to improve grip) 7.2 2.Cutting pliers (used to sever or pinch off) 2 7.2.3 Crimping pliers 7.2.4 Rotational pliers 8. Common wrenches / spanners 8.1 Other general wrenches / spanners 8.2. Spe cialized wrenches / spanners 8.3. Spanners in popular culture 9. Hacksaw, surface plate, surface gauge, , vee-block, files 10.
    [Show full text]
  • ABS HYTORC Product Brochure
    INDUSTRIAL BOLTING SYSTEMS QUALITY WITH EXCELLENCE Since 1998 www.absgroup.in About Us Advanced Bolting Solutions Pvt. Ltd. (ABS) is a leading multinational company providing Precision Torquing, Tensioning, On-Site E Machining, Lifting and High Pressure Systems through consultative sales of leading international brands across multiple locations G in India and the Middle East. TENSIONING With over two decades of expertise and the N mission to be active partners in customer centric growth, we offer Productivity Enhancement Services through technical A ASSEMBLY SOLUTIONS consultations, training, on-site rental services, 24x7x365 technical support and multiple R NABL accredited calibration facilities. Production Tools Our “Joint Integrity Services” ensures leakage free joints and bolt load accuracy while MACHINING maintaining industrial workplace safety T standards. Today, with over 250 employees across all our C facilities, we stand as the frontrunner in providing the most comprehensive solutions to HYDRAULIC JACKS, FLANGE MAINTENANCE & ACCESSORIES every major industry such as Automobile, U Assembly, OEM, Power, Steel, Oil & Gas, Heavy Engineering, Wind, Mining, Shipping and more. D We have a team of (ASME Certified) experts who provide bolting related training courses and certifications. With a diligent focus on O process management, we have a strong Quality Management System comprising of R standard certifications like ISO 9001:2015, ISO 45001:2018 and ISO/IEC 17025. P ABS SERVICE SUPPORT REPAIR AND TOOL PORTABLE MAINTENANCE SERVICING Before conducting repairs, we document and share an RCA We offer doorstep repair and calibration services with the report of the tool. To avoid future breakdowns, we share ABS Mobile Van. With our highly skilled professionals and some precautionary measures to our customers to ensure calibration machine, our van is capable of calibrating tools tool longevity.
    [Show full text]
  • Tool Shed Number 164 June 2011
    NUMBER 164 JUNE 2011 • • • A Journal of Tool Collecting published by CRAFTS of New Jersey • • • A TRIP TO COLONIAL WILLIAMSBURG The Largest Living History Museum By Bob Garay his past fall I took a short a lavish palace where the vacation with my wife to Governor would entertain TWilliamsburg. I had been important guests. It is outfitted there once before back in 1975, with many actual antique fur- but that was in my pre-tool col- nishings of the time and had lecting days. Even so I remem- beautiful gardens to stroll bered it as something special around. As you enter the palace with little shops and bustling the first sight is the arms crowds gathering around activi- arrangement in the front hall. ties going on during the day. The Palace hosted the colony’s This time was going to be quite fashionable society and finest different. Fellow tool collector entertainments. The capital of Hank Allen had given me the Virginia was moved to name and number of CRAFTS Richmond but not before the member and former EAIA first two American governors President Jay Gaynor, who is The only way to tour Williamsburg is a carriage ride. resided in this palace: Patrick director of Historic Trades at Williamsburg. I called Jay and Henry and Thomas Jefferson. he agreed to meet me one day to show me around. We After leaving the palace we strolled down the center entered Williamsburg along the picturesque Colonial of town thru the Palace Green. Off this green I saw the Parkway that was a kaleidoscope of color.
    [Show full text]
  • Installation Instructions
    JK Hood Louver Cut Template Parts List Tools Needed (1) JK Hood Louver Panel • Scissors & sharp hobby knife or razor blade (1) Cut Template with Instructions (this sheet) • Masking tape & fine-tip felt marker Cut out template Cut out template (24) 10-24 X 3/4 SS button head cap screw • Automatic center-punch or punch and hammer along outer edge along outer edge (Step 2) (24) 10-24 nylon insert lock nut • Drill motor with 7/32” drill bit, 3/4“ & 1” hole saws (Step 2) (24) #10 flat washer • High speed cut-off wheel (electric or pneumatic) • Anti-sieze compound • 1/8“ hex key (flat-end, NOT ball-end) • 3/8” wrench or socket & ratchet • Files, sandpaper or burr-knife • Touch-up paint At these hole locations: Drill through At these hole locations: Drill through inner brace, then hole-saw nut inner brace, then hole-saw nut access hole from underside access hole from underside (Step 13) (Step 13) Existing Existing Windshield Windshield Bumper Hole Bumper Hole (Step 3) (Step 3) Drill/Hole Saw Locations (Steps 4 & 6) Inside Corner Inside Corner (Step 4 - punch/mark (Step 4 - punch/mark but do not drill) but do not drill) Cut HoodAlong Dotted Lines (Step 8) Poison Spyder Customs www.poisonspyder.com 8. Use a cut-off wheel to cut along the cut lines made in the previous step. DO (951) 849-5911 Installation Procedure NOT CUT INTO the X-brace on the underside of the hood. There is a thin layer of adhesive material between the outer sheetmetal and the X-brace, which will allow you to carefully cut through the outer layer of sheetmetal without cutting in to the X-brace.
    [Show full text]
  • Hand and Power Tool Safety Tips Selecting the Right Tool, Posture and Positioning
    UC Monthly Safety Spotlight, February 2012 Shop, Tool and Electrical Safety Hand and Power Tool Safety Tips Selecting the Right Tool, Posture and Positioning Understanding grips, force and pressure Power Grip: provides maximum hand power Pinch Grip: The hand grip provides control for high force tasks. All the fingers should for precision and accuracy. The tool is comfortably wrap around the tool handle gripped between the thumb and fingertips. Double-handle tools: plier-like tools measured Single hand grip: Tool is positioned to take by handle length and grip span. Grip span: The advantage of pressure from a hard surface, distance between the thumb and fingers when point or edge on any part of the body. the tool jaws are open or closed. Contact Pressure: Pressure from a hard surface, point, or edge on any part of your body. Awkward postures are postures that strain the neck, shoulders, elbows, wrists, hands or back. Bending, stooping, twisting and reaching are examples of awkward postures. Tool use and body positioning the work piece will affect your shoulder, elbow, wrist, hand or back posture. Choose an ergonomic tool requiring the least continuous force and which can be used without awkward postures. The right tool will help you to minimize pain and fatigue by keeping your neck, shoulders, and back relaxed and your arms at your sides. Avoid raising your shoulders and elbows; relaxed shoulders and elbows are more comfortable and will make it easier to drive downward. Ergonomic Tools • A tool becomes “ergonomic” only when it fits the task you are performing and it fits your hand without causing awkward postures, harmful contact pressures or other safety and health risks.
    [Show full text]
  • Heavy Duty 4' 1 Drawer Work Bench
    Heavy Duty 4’ MODEL NUMBER 1 Drawer Work Bench MRWB - 4 Heavy Duty Work Bench MRWB - 4 3 Shelf 1 Drawer - 60”h x 24”d x 48”w Description Qty. Part Number Part Size 36” Post (Top Back) 2 HWPT3602T 36” 36” Post (Bottom Front) 2 HWPT3602 36’ Brace 4 RWBE2303 24” Beam 5 RWBE4703 48” 24” Post (Bottom Back) 2 HWPT2402 24” Top Shelf Support 1 RWSS4803 48” Drawer Mount 2 RWDM2305 N/A Drawer Slide 2 RWDS2003 N/A Drawer Shelf Braces 2 RWDB4302 43” Peg Board 1 PGBD4820 20” x 48” Wood Shelf 2 RLPB2448 24” x 48” Wood Drawer Shelf 1 RPB43017 17” x 43” Wood Top Shelf 1 RPB2489 9” x 48” Hardware 4 NB4 #10-24 Safety Instructions These units should be placed on a level surface. Failure to do so can result in poor product performance or create a possible safety hazard. This unit should be securely anchored to a wall or floor with suitable fasteners, which are not included. Do not use this unit for anything other than the manufactures intended purpose. DO NOT STAND ON ANY PART OF THE UNIT, OR USE IT AS A LADDER. Evenly distribute the weight on each level and always keep the heavier loads on the bottom. Use care when working with metal parts. General Instructions Assembly is done with the rivets of the beams and braces fitting into the slots of the post. A rubber mallet may be used on the beams and braces to seat the rivets properly. A hammer can also be used, providing one uses a cloth or a block of wood between the hammer head and the parts to prevent damage.
    [Show full text]