Heavy Duty 6’ MODEL NUMBER Work Bench MRWB - 6 Heavy Duty Work Bench MRWB-6 3 Shelf 2 Drawer - 60”h x 24”d x 72”w Description Qty. Part Number Part Size Long Post 2 RUPT6002 60” Brace 4 RWBE2303 24” Beam 5 RWBE7103 72” Short Post 2 RUPT3602 36” Shelf Support 2 RWSB2801 N/A Top Shelf Beam 1 RWSS8903 N/A Drawer Mount 2 RWDM2305 N/A Drawer Slide 4 RWDS2003 N/A Drawer Shelf Braces 4 RWDB3102 32” Peg Board 1 PGBD7120 20” x 72” Wood Shelf 2 RLPB2472 24” x 72” Center Bracket 2 RWBR0303 N/A Center Drawer Mount 2 RWDM2303 N/A Peg Board Bracket 2 RWPB0401 N/A Wood Drawer Shelf 2 RPB23217 32” x 17” Wood Top Shelf 1 RPB2729 9” x 72” Hardware 12 NB12 #10-24 Safety Instructions These units should be placed on a level surface. Failure to do so can result in poor product performance or create a possible safety hazard. This unit should be securely anchored to a wall or floor with suitable fasteners, which are not included. Do not use this unit for anything other than the manufactures intended purpose. DO NOT STAND ON ANY PART OF THE UNIT, OR USE IT AS A LADDER. Evenly distribute the weight on each level and always keep the heavier loads on the bottom. Use care when working with metal parts. General Instructions Assembly is done with the rivets of the beams and braces fitting into the slots of the post. A rubber mallet may be used on the beams and braces to seat the rivets properly. A hammer can also be used, providing one uses a cloth or a block of wood between the hammer head and the parts to prevent damage. Tap gently and be sure the rivets are straight and fully engaged. Should you have any comments, damage, missing parts, or problems with assembly of this unit please feel free to contact our Edsal manufacturing facility at, (773) 475-3000 and request customer service. We can Consumer Products Division also be reached on the internet at the following email address : [email protected]. Edsal Manufacturing Company 4400 South Packers Avenue To obtain replacement parts, please provide the following information : Chicago, IL 60609 www.edsal.com - Model # - Part # & Description - Location Purchased - Date Purchased Assembly Instructions for MRWB - 6 Post are directional. Tap Lightly 72” Beam (Bend facing down) Step The slot must point Step Peg Board Brackets down. Top Shelf Beam 1 Shelf Ledge Up 2 Long Post Skip Hole From Bottom Figure A 24” Brace Peg Board Bracket Shelf Support Drawer Mount Center Mounting Drawer Slides Bracket Drawer Slide Shelf Support Short Post Center Drawer Mount 72” Beams Take two (2) 24” braces with the shelf ledge facing up, and Take four (4) 72” beams with the bend facing up, and attach one (1) short 36” post and attach rivets from the brace to the the rivets even with the braces from the two end assembly's, top two (2) holes of the short post. Take one (1) long 60” and tap down to seat. Install the top shelf beam and one (1) post and attach the opposite end of the brace to the holes of 72” beam with the bend facing down, to the top holes of the the long post so the brace is level, tap down brace to seat. back posts. Next install a peg board bracket to the beam of Attach the bottom brace to the short post skipping one (1) the top assembly using the nuts and bolts provided. Assem- hole from the bottom and the opposite end to the long post, ble the center drawer assembly by taking a peg board bracket, tap down brace to seat. Take one (1) drawer mount and skip one (1) shelf support, and one (1) center mounting bracket one (1) hole from the top brace and attach rivets to the and bolt them to the work surface back beam (see figure A). short and long post, tap down drawer mount to seat. take Next bolt the shelf support bracket, and the last center mount- one (1) drawer slide and insert it into the slide of the drawer ing bracket to the opposite beam. Attach the two (2) center mount. Repeat this step for the opposite end assembly. drawer mounts by placing the rivets into the holes of the cen- ter mounting brackets. Insert the drawer slides into the center drawer mount slides. Add the final shelf support to the bot- tom two (2) beams using the nuts and bolts provided. Step 4th Hole Down Step 3 4 Peg Board 32” Drawer Shelf Braces (Bend facing down) (Back of drawer slides also) Place the peg board to the inside of the back post of the work Add the wood shelves to the top shelf support, the draw- bench. Using the fourth hole from the top of the back post, ers, the bottom shelf, and the work surface to finalize the align the holes of the peg board to the holes on the back assembly of the workbench. post, and fasten using the nuts and bolts provided. Align the holes on the peg board brackets to the holes of the peg board, and fasten the peg board to the peg board brackets using the nuts and bolts provided. Take the four (4) 32” drawer shelf braces and with the shelf ledge facing down, insert the two (2) rivets into the two (2) holes located on the drawer slides. .