Kia Rio 2001 / Sephia 1995-2001 Spectra 2000-2001 / Sportage 1998
Total Page:16
File Type:pdf, Size:1020Kb
Installation instructions for part 99-1009 Kia Rio 2001 / Sephia 1995-2001 Table of Contents Spectra 2000-2001 / Sportage 1998-2002 Dash Disassembly 99-1009 – Kia Rio 2001 ........................................................ 2 – Kia Sephia 1995-2001 ......................................... 3 KIT FEATURES – Kia Spectra 2000-2001 ........................................ 3 • ISO DIN radio provision with pocket • ISO DDIN radio provision – Kia Sportage 1998-2000 ...................................... 3 – Kia Sportage 2001-2003 ...................................... 4 Kit Preparation ....................................................... 5 KIT COMPONENTS Kit Assembly • A) Radio housing A • B) Radio housing B • C) Radio brackets • D) Pocket • E) (4) #8 x 3/8” Phillips screws – ISO DIN radio provision with pocket ...................... 6 A B C D E – ISO DDIN radio provision ...................................... 6 WIRING & ANTENNA CONNECTIONS (sold separately) Wiring Harness: • 70-1003 CAUTION! All accessories, switches, climate controls panels, and Antenna Adapter: • Not required especially air bag indicator lights must be connected before cycling TOOLS REQUIRED the ignition. Also, do not remove the factory radio with the key in the REV. 5/2/2016 INST99-1009 REV. on position, or while the vehicle is running. • Panel removal tool • Phillips screwdriver • Cutting tool METRA. The World’s best kits.™ metraonline.com © COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATION 99-1009 Dash Disassembly Kia Rio 2001 1. Remove ashtray and (1) Phillips FF O A/C head screw inside ashtray cavity. F OF (Figure A) A/C F 2. Remove knob from climate control OF slide lever. (Figure B) A/ 3. Unsnap and remove radio/climate control trim panel. (Figure C) 4. Remove (4) Phillips head screws securing the radio. Unplug and (Figure A) (Figure B) (Figure C) remove the radio. Continue to kit preparation 2 99-1009 Dash Disassembly Kia Sephia 1995-1997 Kia Sephia 1998-2001 Kia Sportage 1998-2000 Kia Spectra 2000-2001 1. Remove plastic screw cover to the left of the 1. Unclip and remove dash trim panel. coin tray and remove the Phillips head screw 1. Remove (1) Phillips head screw from above instrument 2. Remove (4) Phillips head screws securing the from behind cover. cluster. radio. Unplug and remove the radio. 2. Remove switch blank to the far right of the 2. Unclip and remove dash trim panel. Continue to kit preparation switch panel and remove the Phillips head screw from behind switch blank. 3. Remove (4) Phillips head screws securing the radio. Unplug and remove the radio. 3. Unclip and remove dash trim panel. Continue to kit preparation 4. Remove (4) Phillips head screws securing the radio. Unplug and remove the radio. Continue to kit preparation 3 99-1009 Dash Disassembly Kia Sportage 2001-2002 1. Unclip and remove climate control/vent trim panel. (Figure A) 2. Remove screw covers from trim panel below steering column and remove screws from behind covers. Lower the trim panel (it is not necessary to remove the panel). (Figure B) 3. Remove (3) Phillips head screws from bottom of steering column housing and remove both upper and lower sections of housing. (Figure A) (Figure C) 4. Remove (1) Phillips head screw from outside left edge of dash and (2) Phillips head screws from near hood release. (Figure C) 5. Loosen nut behind hood release and remove lower left side dash trim. (Figure C) 6. Remove (4) Phillips head screws from instrument trim panel and remove panel. (Figure D) 7. Remove (4) Phillips head screws securing the radio. Unplug and remove the radio. Continue to kit preparation (Figure B) (Figure D) 4 99-1009 Kit Preparation Kia Rio 2001 Kia Sephia 1998-2001 Kia Sportage 1998-2002 Radio brackets Kia Sephia 1995-1997 Kia Spectra 2000-2001 1. Use the trim without the notched 1. Use the following sets of mounting 1. Use the trim with notched corners 1. Use the trim without the notched corners and the third set of tabs for each model respectively. at the top and the first set of tabs corners and the second set of mounting tabs. (Figure C) The fourth set of tabs will not be on the brackets. (Figure A) mounting tabs. (Figure B) used in this kit. (Figure D) Continue to radio brackets Continue to radio brackets Continue to radio brackets Continue to radio brackets 1st Set 3rd Set 4th Set 2nd Set (Not Used in this kit) (Figure A) (Figure B) (Figure C) (Figure D) 5 99-1009 Kit Assembly ISO DIN radio provision with pocket ISO DDIN radio provision 1. Slide the radio brackets into the 1. Slide the radio brackets into the radio housing, aligning the holes in radio housing, aligning the holes in the radio housing to the clips on the the radio housing to the clips on the brackets. (Figure A) brackets. (Figure A) 2. Attach the pocket to the lower section of the radio brackets using the (4) 2. Slide the radio into the completed #8 x 3/8” Phillips screws provided. assembly, and then secure using (Figure B) the screws supplied with the radio. (Figure B) 3. Remove the metal DIN sleeve and trim ring from the aftermarket radio. 3. Locate the factory wiring harness (Figure A) and antenna connector in the (Figure A) 4. Slide the radio into the bracket/ pocket assembly, and then secure it dash and complete all necessary using the screws supplied with the connections to the radio. Metra radio. (Figure B) recommends using the proper mating adapter from Metra or 5. Locate the factory wiring harness and AXXESS. Test the radio for proper antenna connector in the dash and operation. complete all necessary connections to the radio. Metra recommends 4. Secure the completed assembly using the proper mating adapter from into the dash, and then reassemble Metra or AXXESS. Test the radio for the dash in reverse order of proper operation. disassembly. 6. Secure the completed assembly into the dash, and then reassemble the (Figure B) (Figure B) dash in reverse order of disassembly. 6 99-1009 Notes 7 Installation instructions for part 99-1009 IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling. KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians REV. 5/2/2016 INST99-1009 REV. METRA. The World’s best kits.™ metraonline.com © COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATION.