DOCSLIB.ORG

Density in the Flotation Process Whitepaper

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Density in the Flotation Process Whitepaper DENSITY IN THE FLOTATION PROCESS WHITEPAPER INTRODUCTION THE FROTH FLOTATION PROCESS Are you looking for a higher recovery rate in In previous process stages fine particles the Flotation process by means of were created and valuable minerals were automation and instrumentation? This released from their carriers, also called the whitepaper describes the purposes and gangue. In general, flotation is used to benefits of measuring density at different separate and recover. The valuables are applications in froth flotation. First, the concentrated and separated from the unwanted particles (gangue). This is done froth flotation process itself and control using chemicals and froth. Basically, this purposes are explained, then five key process exploits differences in surface reasons for measuring density will be given. properties between minerals and gangues. A full optimization for a maximum recovery The froth flotation principle is a complex in the flotation process can only be combination of the laws of surface achieved when a novel of instruments and chemistry, crystallography and physics. The analyzers are used together, such as density process efficiency depends on aspects such as density, electrical conductivity and gauges, level gauges, flow meters, froth physical and chemical properties. cameras, etc. This whitepaper will show the importance of the Density meter, which is Without a flotation process, many metals Rhosonics’ area of expertise. and inorganic raw materials would be extremely scarce and expensive, as there are currently not many high-grade deposits that could be processed by simple physical and mechanical methods. Addition of chemicals Mass flow meter Air addition supply Mass flow meter pH sensor Froth Feed slurry Ultrasonic Slurry Density Meter (SDM) Underflow Figure 1: The flotation cell overview of measuring applications ©RHOSONICS ∙ WHITEPAPER ∙ FIVE REASONS FOR MEASURING DENSITY IN THE FLOTATION PROCESS ∙ 06/2020 ∙ WWW.RHOSONICS.COM PURPOSE OF PROCESS CONTROL WHY DENSITY MEASUREMENT? The main objectives when controlling the Instruments, such as density meters help flotation process is to maximize the recovery operators to efficiently monitor and control and boost the metallurgical performance. the flotation process, optimize it and An enriched product is created by decreasing prevent process failures. the amount of gangue. When used together with an advanced To achieve these objectives the slurry control system, density readings allow to needs to be continuously monitored and automatically control valves, pumps and controlled, allowing process stabilization have an efficient chemical or air dosing, and ensuring optimal flotation conditions. resulting in the improvement of the process that can lead to a higher enrichment and MEASURING POINTS recovery of valuable materials. In the flotation cell, there are several There are multiple reasons for measuring possible installation points for density density in the flotation process, which meters. For example in the feed slurry, could differ per application. The following underflow of the cells and final concentrate. five topics are highlighting the main reasons Please check the overview of measuring for measuring density. points in figure 1. Released particles Binary composites Ternary composites Gangue Valuable 1 Valuable 2 Figure 2: The flotation cell needs to separate the valuable materials from the gangue ©RHOSONICS ∙ WHITEPAPER ∙ FIVE REASONS FOR MEASURING DENSITY IN THE FLOTATION PROCESS ∙ 06/2020 ∙ WWW.RHOSONICS.COM 1: OPTIMUM FEED DENSITY middle size particles consist of minerals and gangue. The gangue can only be separated Density measurement in the flotation feed from the valuable minerals in the flotation is a known installation point in mineral cells when the particles were grinded fine processing. The percentage of solids in the enough in previous stages. feed is important for optimal operation of the flotation cell. Also, a combination of a density meter and a flow meter in the flotation feed and line of the final product of the flotation, allow to calculate the performance of the circuit. The optimal pulp density in the feed of the flotation process depends on the type of ore, due to different characteristics such as specific gravity and shape of the particles. For example, silicate minerals respond best Figure 3: The bubbles remove the fine particles to the flotation process at a feed density of approx. 20 to 30 % solids and the optimal Real-time density measurement can help to coal pulp density varies in practice from 6 verify changes in the slurry from the to 25 % solids (Yarar & Dogan, 1984). grinding circuit to the flotation cells. The Additional research should be done to slurry density has a high correlation with determine the optimum feed for a particle size, therefore the operator could particular operation. use this parameter (together with other The effect of flotation feed density on variables) to improve the control over the metallurgical performance has been process. investigated. Results of test work have shown that the pulp density affects key 3: EFFICIENT ENRICHMENT parameters of the flotation process in both Optimal flotation means reducing the the pulp and froth phases (Runge et al., amount of gangue that is sent together with 2012). One of the findings was that froth phase recovery presumably improves valuable minerals to further stages of the because of a stabilising effect due to a process. An enriched product should be greater loading of solids on bubble produced with the lowest energy costs, surfaces. containing most valuable materials (the concentrate). Decreasing the amount of 2: PREVENT MIDDLINGS gangue can improve the quality of the concentrate. Particle size plays a crucial role for the enrichment of ore in the flotation process. Instrumentation plays a crucial role in this The flotation operator wants to prevent enrichment process, because it is the base middling’s (product which is neither clean for all process control. Automation can lead mineral product nor reject/tailings). These to a high level of performance in the circuit. ©RHOSONICS ∙ WHITEPAPER ∙ FIVE REASONS FOR MEASURING DENSITY IN THE FLOTATION PROCESS ∙ 06/2020 ∙ WWW.RHOSONICS.COM Besides density, the air injection and dosing of reagents should be monitored and controlled for efficient product enrichment. Smart air injection could solve problems with froth levels without using too much reagents. The correct choice of instrumentation can only be achieved if a detailed understanding of the operation and application of the required instrument is acquired within a Figure 5: Advanced flotation cell process control given process (Laurila et al., 2002). 4: FALLING SLURRY LEVEL The pulp level inside the cell can fall due to an increase of ore feeding (XinHai, 2020). In Optimization this case, the flotation operator should Maximize the beneficiation decrease the feed density, adjust grinding and classifying processes or adjust the Advanced control reagent dosing or air injection to keep the Reject disturbances, control slurry level at a certain point. An in-line Base level control density meter can be used to check in real- Control froth level, aeration time the amount of ore in the feed (XinHai, rate and dosing of reagents 2020). Instrumentation Valves, sensors, level gauges, density meters Figure 4: Hierarchy in the flotation control system (Laurila et al., 2002) Installing sensors is important, but the sensor itself will not guarantee continued performances. Having a skilled team is also essential. The flotation operator should be Figure 6: Flotation cells at a Moroccan processing capable of interpreting and understanding plant the measurement data. The operator is 5: ORE PILES UP IN THE TANK critical in order to make the most out of the collected process data. Advanced process Another problem is that the ore in the control is needed to support the operator flotation tank piles up (XinHai, 2020), this and to achieve good performances in the could have been caused by a too high feed entire flotation circuit (Di Sandro, 2017). slurry solid content, which can be monitored in real-time by the use of a density meter. ©RHOSONICS ∙ WHITEPAPER ∙ FIVE REASONS FOR MEASURING DENSITY IN THE FLOTATION PROCESS ∙ 06/2020 ∙ WWW.RHOSONICS.COM Other reasons could be changes in pressure, CONCLUSION a high inflating volume and changes in the suction capacity of the suction tank. The As discussed in this whitepaper, measuring flotation operator can use different tools to density in the flotation circuit is important. make the slurry flow again. Density measurement can be used for advanced process control, preventing AVAILABLE EQUIPMENT falling slurry levels and ore piling up in the tank, and to increase the efficiency and Density measurement is usually done by recovery in the flotation process. Together radiation-based measuring devices. This with flow measurement, the density can technology has been used in the mineral also be used for the mass balance, and to processing industry for decades. However, calculate the performance of the circuit. nowadays governmental regulations are getting stricter and associated costs are MORE INFORMATION? increasing. More nuclear density meters are being replaced by alternatives. These Rhosonics has more than ten years of alternatives can do the same job, without experience in using ultrasonic technology administration costs and health and safety for non-nuclear density measurement in risks related to the nuclear source. the mineral processing
Load more

Recommended publications
  • A Review of Flotation Separation of Mg Carbonates (Dolomite and Magnesite)
    minerals Review A Review of Flotation Separation of Mg Carbonates (Dolomite and Magnesite) Darius G. Wonyen 1,†, Varney Kromah 1,†, Borbor Gibson 1,† ID , Solomon Nah 1,† and Saeed Chehreh Chelgani 1,2,* ID 1 Department of Geology and Mining Engineering, Faculty of Engineering, University of Liberia, P.O. Box 9020 Monrovia, Liberia; [email protected] (D.G.W.); [email protected] (Y.K.); [email protected] (B.G.); [email protected] (S.N.) 2 Department of Electrical Engineering and Computer Science, University of Michigan, Ann Arbor, MI 48109, USA * Correspondence: [email protected]; Tel.: +1-41-6830-9356 † These authors contributed equally to the study. Received: 24 July 2018; Accepted: 13 August 2018; Published: 15 August 2018 Abstract: It is well documented that flotation has high economic viability for the beneficiation of valuable minerals when their main ore bodies contain magnesium (Mg) carbonates such as dolomite and magnesite. Flotation separation of Mg carbonates from their associated valuable minerals (AVMs) presents several challenges, and Mg carbonates have high levels of adverse effects on separation efficiency. These complexities can be attributed to various reasons: Mg carbonates are naturally hydrophilic, soluble, and exhibit similar surface characteristics as their AVMs. This study presents a compilation of various parameters, including zeta potential, pH, particle size, reagents (collectors, depressant, and modifiers), and bio-flotation, which were examined in several investigations into separating Mg carbonates from their AVMs by froth flotation. Keywords: dolomite; magnesite; flotation; bio-flotation 1. Introduction Magnesium (Mg) carbonates (salt-type minerals) are typical gangue phases associated with several valuable minerals, and have complicated processing [1,2].
    [Show full text]
  • Effects of Varied Process Parameters on Froth Flotation Efficiency: a Case Study of Itakpe Iron Ore
    Nigerian Journal of Technology (NIJOTECH) Vol. 39, No. 3, July 2020, pp. 807 – 815 Copyright© Faculty of Engineering, University of Nigeria, Nsukka, Print ISSN: 0331-8443, Electronic ISSN: 2467-8821 www.nijotech.com http://dx.doi.org/10.4314/njt.v39i3.21 EFFECTS OF VARIED PROCESS PARAMETERS ON FROTH FLOTATION EFFICIENCY: A CASE STUDY OF ITAKPE IRON ORE S. Akande1, E. O. Ajaka2, O. O. Alabi3 and T. A. Olatunji4,* 1, 2, DEPARTMENT OF MINING ENGINEERING, FEDERAL UNIV. OF TECHNOLOGY, AKURE, ONDO STATE, NIGERIA 3, 4, DEPT. OF MET. & MATERIALS ENGINEERING, FEDERAL UNIV. OF TECHNOLOGY, AKURE, ONDO STATE, NIGERIA Email addresses: 1 [email protected], 2 [email protected], 3 [email protected], 4 [email protected] ABSTRACT The dire need for Itakpe iron ore concentrates of appreciable iron content meets for smelting operation necessitated this study. Core samples of the iron ore sourced from Itakpe, Kogi State, Nigeria were prepared for petrological analysis followed by chemical and particle size analyses. Froth flotation was done using different collectors at varying particle sizes and pH values. Characterization studies carried out revealed that Itakpe iron ore is a lean ore assaying 36.18% Fe2O3 and contains predominantly quartz, sillimanite, and haematite. Its liberation size lies favourably at 75 µm. Processing the ore by froth flotation yielded appreciable enrichment. Optimal recovery (~92%) was achieved using potassium amyl xanthate (PAX) at pH 11 for fine feed sizes (<125 µm) yielding iron concentrate assaying 67.66% Fe2O3. Thus, processing at this set-of- conditions is recommended for the industrial production of more enriched Itakpe iron ore concentrates.
    [Show full text]
  • Evaluation of Scale-Up Model for Flotation with Kristineberg Ore
    Evaluation of Scale-up Model for Flotation with Kristineberg Ore Adam Isaksson Chemical Engineering, master's level 2018 Luleå University of Technology Department of Civil, Environmental and Natural Resources Engineering Evaluation of Scale-up Model for Flotation with Kristineberg Ore Adam Isaksson 2018 For degree of MASTER OF SCIENCE Luleå University of Technology Department of Civil, Environmental and Natural Resources Engineering Division of Minerals and Metallurgical Engineering Printed by Luleå University of Technology, Graphic Production 2018 Luleå 2018 www.ltu.se Preface As you may have figured out by now, this thesis is all about mineral processing and the extraction of metals. It was written as part of my studies at Luleå University of Technology, for a master’s degree in Chemical Engineering with specialisation Mineral and Metal Winning. There are many people I would like to thank for helping me out during all these years. First of all, my thanks go to supervisors Bertil Pålsson and Lisa Malm for the guidance in this project. Iris Wunderlich had a paramount role during sampling and has kindly delivered me data to this report, which would not have been finished without her support. I would also like to thank Boliden Mineral AB as a company. Partly for giving me the chance to write this thesis in the first place, but also for supporting us students during our years at LTU. Speaking of which, thanks to Olle Bertilsson for reading the report and giving me feedback. The people at the TMP laboratory deserves another mention. I am also very grateful for the financial support and generous scholarships from Jernkontoret these five years.
    [Show full text]
  • Flotation of Copper Sulphide from Copper Smelter Slag Using Multiple Collectors and Their Mixtures
    International Journal of Mineral Processing 143 (2015) 43–49 Contents lists available at ScienceDirect International Journal of Mineral Processing journal homepage: www.elsevier.com/locate/ijminpro Flotation of copper sulphide from copper smelter slag using multiple collectors and their mixtures Subrata Roy a,⁎, Amlan Datta b, Sandeep Rehani c a Aditya Birla Science and Technology Company Ltd., Taloja, Maharashtra, India b Formerly with Aditya Birla Science and Technology Company Ltd., Taloja, Maharashtra, India. c Birla Copper, Dahej, Gujarat, India article info abstract Article history: Present work focuses on the differences in the performances obtained in the froth flotation of copper smelter Received 14 August 2014 slag with multiple collector viz. sodium iso-propyl xanthate (SIPX), sodium di-ethyl dithiophosphate (DTP) Received in revised form 11 February 2015 and alkyl hydroxamate at various dosages. Flotation tests were carried out using single collectors as well as var- Accepted 20 August 2015 ious mixtures of the two collectors at different but constant total molar concentrations. Flotation performances Available online 28 August 2015 were increased effectively by the combination of collectors. The findings show that a higher copper recovery (84.82%) was obtained when using a 40:160 g/t mixture of sodium iso-propyl xanthate (SIPX) with di-ethyl Keywords: Flotation dithiophosphate compared to 78.11% with the best single collector. Similar recovery improvement (83.07%) Copper slag was also observed by using a 160:40 g/t mixture of sodium iso-propyl xanthate (SIPX) with alkyl hydroxamate. Sodium isobutyl xanthate The results indicate that in both cases DTP and alkyl hydroxamate played important role as co-collector with SIPX Hydroxamate for the recovery of coarse interlocked copper bearing particles and has an important effect on the behaviour of Dithiophosphate the froth phase.
    [Show full text]
  • Recovery of Phosphate Minerals from Plant Tailings Using Direct Froth Flotation
    minerals Article Recovery of Phosphate Minerals from Plant Tailings Using Direct Froth Flotation Ashraf Alsafasfeh and Lana Alagha * Department of Mining & Nuclear Engineering, Missouri University of Science and Technology, Rolla, MO 65409, USA * Correspondence: [email protected]; Tel.: +1-573-341-6287; Fax: +1-573-341-6934 Received: 13 June 2017; Accepted: 9 August 2017; Published: 12 August 2017 Abstract: Wastes produced from the phosphate industry presents many challenges due to the high economic and environmental impacts involved with their disposal. However, the relative scarcity of high-grade phosphate ores has driven researchers to recover and recycle these valuable wastes (secondary sources). The goal of this study was to investigate the possibility of upgrading the P2O5 content in tailings produced from a phosphorous production plant using direct froth flotation. Characterization assays, including X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray fluorescence (XRF), and mineral liberation analysis (MLA), were first conducted to identify the mineralogical and morphological characteristics of tailings samples and grain properties to better understand the behavior of the flotation feed. Flotation experiments were conducted using Denver D-12 in a 1-L flotation cell in the presence of sodium silicate (dispersant) and sodium oleate (collector). Several parameters, such as the solids content of the flotation pulp, pulp pH and flotation time, were investigated to optimize the recovery and grade of the concentrate products. Results obtained from this study indicated that the P2O5 content in plant tailings could be upgraded from 21.57% to 28.4% at >73% recovery. Keywords: phosphate minerals; froth flotation; mineral liberation analysis; sodium silicate 1.
    [Show full text]
  • Metal Losses in Pyrometallurgical Operations - a Review
    Advances in Colloid and Interface Science 255 (2018) 47–63 Contents lists available at ScienceDirect Advances in Colloid and Interface Science journal homepage: www.elsevier.com/locate/cis Historical perspective Metal losses in pyrometallurgical operations - A review Inge Bellemans a,⁎, Evelien De Wilde a,b, Nele Moelans c, Kim Verbeken a a Ghent University, Department of Materials, Textiles and Chemical Engineering, Technologiepark 903, B-9052, Zwijnaarde, Ghent, Belgium b Umicore R&D, Kasteelstraat 7, B-2250 Olen, Belgium c KU Leuven, Department of Materials Engineering, Kasteelpark Arenberg 44, bus 2450, B-3001, Heverlee, Leuven, Belgium article info abstract Article history: Nowadays, a higher demand on a lot of metals exists, but the quantity and purity of the ores decreases. The Received 24 October 2016 amount of scrap, on the other hand, increases and thus, recycling becomes more important. Besides recycling, Received in revised 4 August 2017 it is also necessary to improve and optimize existing processes in extractive and recycling metallurgy. One of Accepted 7 August 2017 the main difficulties of the overall-plant recovery are metal losses in slags, in both primary and secondary Available online 10 August 2017 metal production. In general, an increased understanding of the fundamental mechanisms governing these losses could help further improve production efficiencies. This review aims to summarize and evaluate the current sci- Keywords: fi Pyrometallurgy enti c knowledge concerning metal losses and pinpoints the knowledge gaps. Metal losses First, the industrial importance and impact of metal losses in slags will be illustrated by several examples from Slags both ferrous and non-ferrous industries.
    [Show full text]
  • Extractive Metallurgy of Copper This Page Intentionally Left Blank Extractive Metallurgy of Copper
    Extractive Metallurgy of Copper This page intentionally left blank Extractive Metallurgy of Copper Mark E. Schlesinger Matthew J. King Kathryn C. Sole William G. Davenport AMSTERDAM l BOSTON l HEIDELBERG l LONDON NEW YORK l OXFORD l PARIS l SAN DIEGO SAN FRANCISCO l SINGAPORE l SYDNEY l TOKYO Elsevier The Boulevard, Langford Lane, Kidlington, Oxford OX5 1GB, UK Radarweg 29, PO Box 211, 1000 AE Amsterdam, The Netherlands First edition 1976 Second edition 1980 Third edition 1994 Fourth edition 2002 Fifth Edition 2011 Copyright Ó 2011 Elsevier Ltd. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, mechanical, photocopying, recording or otherwise without the prior written permission of the publisher Permissions may be sought directly from Elsevier’s Science & Technology Rights Department in Oxford, UK: phone (+44) (0) 1865 843830; fax (+44) (0) 1865 853333; email: permissions@ elsevier.com. Alternatively you can submit your request online by visiting the Elsevier web site at http://elsevier.com/locate/permissions, and selecting Obtaining permission to use Elsevier material Notice No responsibility is assumed by the publisher for any injury and/or damage to persons or property as a matter of products liability, negligence or otherwise, or from any use or operation of any methods, products, instructions or ideas contained in the material herein British Library Cataloguing in Publication Data A catalogue record for this book is available from the British Library Library of Congress Cataloging-in-Publication Data A catalog record for this book is available from the Library of Congress ISBN: 978-0-08-096789-9 For information on all Elsevier publications visit our web site at elsevierdirect.com Printed and bound in Great Britain 11 12 13 14 10 9 8 7 6 5 Photo credits: Secondary cover photograph shows anode casting furnace at Palabora Mining Company, South Africa.
    [Show full text]
  • Slag Reprocessing: Magma Copper Company's San Manuel Facility
    I' SLAG REPROCESSING: MAGMA COPPER COMPANY'S SAN MANUEL FACILITY DRAFT August 1993 Prepared by: U.S. Environmental Protection Agency Office of Solid Waste Special Waste Branch 401 M Street, S.W. Washington, D.C. 20460 Pyrite Flotation: Supenbr Mine DISCLAIMER AND ACKNOWLEDGEMENTS This document was prepared by the U.S. Environmental Protection Agency (EPA) with assistance from Science Applications International Corporation (SAIC) in partial fulfillment of EPA Contract No. 68- W0-0025,Work Assignment 209. Magma Copper Company submitted comments on an earlier draft of this report. EPA had amended the report where appropriate to reflect those comments. The mention of company or product names is not to be considered an endorsement by the U.S. Government or the U.S. Environmental Protection Agency (EPA). Draft I August 1993 Slag Reprocessing: San Manuel DISCLAIMER AND ACKNOWLEDGEMENTS This document was prepared by the U.S. Environmental Protection Agency (EPA) with assistance from Science Applications International Corporation (SAIC) in partial fulfillment of EPA Contract No. 68- W0-0025, Work Assignment 209. Magma Copper Company submitted comments on an earlier draft of this report. EPA has responded to those comments and changed the text where appropriate. The mention of company or product names is not to be considered an endorsement by the U.S.Government or the U.S. Environmental Protection Agency (EPA). Draft I August 1993 Slag Reprocessing: Son Munuti TABLE OF CONTENTS 1 .0 Introduction .................................................. 1 2 .0 Pollution PreventionNaste Minimization with Slag Reprocessing ................. 1 2.1 Slag Reprocessing .......................................... 4 2.2 costs .................................................. 9 2.3 Benefits ............................................... 10 2.4 Limitations ............................................
    [Show full text]
  • Flotation of Sulphide Ores - HZL Experience
    FROTH FLOTATION : RECENT TRENDS @IIME, JAMSHEDPUR, 1998; pp. 18-41 Flotation of Sulphide Ores - HZL Experience V.P. KOHAD Hindustan Zinc Ltd., Zawar Mines, Udaipur - 313 901 ABSTRACT Flotation process, patented in the year 1906, was originally developed for mineral industry to recover values from high grade tailings of gravity separation plants. This technology has acclaimed importance as a versatile process for the beneficiation of vast variety of sulphide minerals. Due to flexibility of the process and remarkable development taken place in flotation technology and its ancillary systems, it has now become possible to recover fine grained sulphide minerals from complex ore deposits, whose processing was earlier considered un- economical. Today, about 400 million tonnes of sulphide ore is treated annually by flotation process worldwide. M/s Hindustan Zinc Ltd. (HZL), a leading lead-zinc mining and smelting company in India has experienced a spectacular growth from the time of its inception. Starting from a single 500 MT per day lead-zinc mine at Zawar, HZL has expanded its mining capacity to about 13,000 MT per day with matching ore beneficiation plants, all adopting froth flotation technology. The phenomenal progress is a result of HZL's emphasis on research and development with an objective to improve the efficiency and to optimize performance, and to seek innovative modern technology and control systems in their flotation plant and processes. This has not only solved metallurgical problems but improved overall plant economics. High grade concentrates produced with reduced deleterious impurities have further enhanced smelting efficiency. The paper covers general principles and aspects of industrial sulphide ore flotation practices in brief and processes adopted in HZL's plants.
    [Show full text]
  • Flash Flotation of Free Coarse Gold Using Dithiophosphate and Dithiocarbamate As a Replacement for Traditional Amalgamation •
    Flash flotation of free coarse gold using dithiophosphate and dithiocarbamate as a replacement for traditional amalgamation • Moisés Oswaldo Bustamante-Rúaa, Doria Maria Naranjo-Gómezb, Alan José Daza-Aragóna, a a Pablo Bustamante-Baena & Julián David Osorio-Botero a Facultad de Minas, Universidad Nacional de Colombia, Medellín, Colombia. [email protected], [email protected], [email protected], [email protected] b Distribuidora de Quimicosindustriales S.A, Medellín, Colombia. [email protected] Received: January 19th, 2018. Received in revised form: April 4th, 2018. Accepted: April 27th, 2018. Abstract This article develops the flash flotation as an alternative method to gravitational separation and amalgamation in order to achieve a greater recovery of coarse native gold through selective hydrophobicity. This method is directly applicated in the discharge of the mills and / or classifiers to recover free and coarse gold; which size is superior than approximately 150 micrometers. Physicochemical characterization of the free gold surfaces was carried out by the measurements of contact angle, Z potential (ZPC) and atomic force microscopy (AFM). The reagent was determined by specific conditions (basic pH, no requirements of an activator and a flotation time of the order of 2 minutes) achieving a superior recovery than 90%. In this case, the isoamyl dialkyl dithiophosphate collector (AERO 3501®) was the reagent which basically got the best results. Keywords: flash flotation; free coarse gold; dithiophosphate; ditiocarbamato; amalgamation. Flotación flash de oro nativo grueso usando ditiofosfato y ditiocarbamato como remplazo de la amalgamación tradicional Resumen En el presente trabajo se desarrolla la flotación flash como un método alternativo a la separación gravitacional y la amalgamación con el fin de alcanzar una mayor recuperación de oro nativo grueso a través de la hidrofobicidad selectiva.
    [Show full text]
  • 1 Froth Flotation
    1 Froth Flotation – Fundamental Principles Froth flotation is a highly versatile method for physically separating particles based on differences in the ability of air bubbles to selectively adhere to specific mineral surfaces in a mineral/water slurry. The particles with attached air bubbles are then carried to the surface and removed, while the particles that remain completely wetted stay in the liquid phase. Froth flotation can be adapted to a broad range of mineral separations, as it is possible to use chemical treatments to selectively alter mineral surfaces so that they have the necessary properties for the separation. It is currently in use for many diverse applications, with a few examples being: separating sulfide minerals from silica gangue (and from other sulfide minerals); separating potassium chloride (sylvite) from sodium chloride (halite); separating coal from ash-forming minerals; removing silicate minerals from iron ores; separating phosphate minerals from silicates; and even non-mineral applications such as de-inking recycled newsprint. It is particularly useful for processing fine-grained ores that are not amenable to conventional gravity concentration. Chemistry Components Collectors Frothers Activators Depressants pH Flotation System Equipment Components Operation Components Cell Design Feed Rate Agitation Mineralogy Air Flow Particle Size Cell Bank Configuration Pulp Density Cell Bank Control Temperature Figure 1: The flotation system includes many interrelated components, and changes in one area will produce compensating effects in other areas (Klimpel, 1995) Froth flotation is a good example of an engineering “system”, in that the various important parameters are highly inter-related, as shown in Figure 1. It is therefore important to take all of 1 these factors into account in froth flotation operations.
    [Show full text]
  • Beneficiation of Oil Shale by Froth Flotation: Critical Review
    Send Orders for Reprints to [email protected] The Open Mineral Processing Journal, 2014, 7, 1-12 1 Open Access Beneficiation of Oil Shale by Froth Flotation: Critical Review S., Al-Thyabat1,*, E. Al-Zoubi2, H. Alnawafleh1 and K. Al-Tarawneh1 1Department of Mining Engineering, Al-Hussein Bin Talal University, Jordan 2Department of Chemistry - Al-Hussein Bin Talal University, Jordan Abstract: Oil shale beneficiation by froth flotation hasn’t received enough attention in the last two decades. The reason was the economics of the process as well as its environmental impact. However, the recent surge in oil price and recent developments in fine grinding technologies may improve the efficiency of oil shale beneficiation by such process. In this work, oil shale concentration by froth flotation technique was critically reviewed. It was found that most of the work was conducted by conventional mechanical flotation using non-ionic collector such as kerosene. Flotation has more pronounced effect on flotation of low grade oil shale; Almost 95% of ash forming minerals were removed to enrich oil shale concentrate by factor of 2-4 with 60-95 % kerogen recovery and approximately 50-300 % increase in oil yield (L/tonne) .Oil shale retorting economics showed that beneficiation reduced the capital cost for pyrolysis and fractionation by 250 % and spent shale disposal by 270%. However, these saving are offset by the cost of beneficiation (grinding, flotation, and dewatering). Therefore, the key for economical oil shale concentration process is the reduction of fine grinding costs. Keywords: Flotation, Oil shale, oil shale beneficiation. 1. INTRODUCTION matrix weight [9].
    [Show full text]