DOCSLIB.ORG

Wall Hanging with Embroidery

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Wall Hanging with Embroidery IC-E-21 1/2 Wall Hanging with Embroidery a…MOKUBA 1540 3.5 mm / No. 558 or similar embroidery ribbon DMC ANCHOR b 739 387 c 839 1086 d 3827 574 【Main body】 Outer fabric Full-size embroidery pattern Lining fabric 30 d… 1-Ply Needle/Settings:3/Satin Stitch 1 pc. each Settings:3 c… 3-Ply Needle/Settings:3/Back Stitch b… 3-Ply Needle/Settings:3/Back Stitch c… 3-Ply Needle/Settings:3/Back Stitch a… Needle for Medium-Fine Yarn/Settings:3/Loop Stitch d… 3-Ply Needle/Settings:3/Satin Stitch d… 3-Ply Needle/Settings:3/Satin Stitch c… 3-Ply Needle/Settings:3/Satin Stitch d… 3-Ply Needle/Settings:3/Velvet-like 22 【Tab】 Outer fabric Lining fabric 【Pocket】 2 pcs. each 18 Outer fabric 12 Lining fabric 1 pc. each Tool • Art No. 8800 Embroidery Stitching Tool 17 5 • Art No. 8801 (Single Ply Needle) • Art No. 8802 (Needle for Medium-Fine Yarn) Procedure • Art No. 8812/8813 1. First, make the main body. Clover Embroidery Hoop (18 cm /12 cm) Transfer the embroidery pattern onto the main-body outer fabric, with the bottom of the pattern located at 15 Material cm from the lower edge of the fabric, and do embroidery • Main body/Pocket (Outr fabric/Lining fabric): as shown in the illustration. Cotton Duck (Beige) 61 cm x 30 cm x 1 pc. Do not transcribe the outlines of flower petals (shown as • Tab: Cotton Fabric (Beige) 18 cm x 5 cm x 2 pcs. dotted lines on the pattern). • Adhesive interlining/white 15 • Lace: 1.5 cm width x 17 cm x 1 pc. Stitch the center of a flower first, and then make loop- • Buttons: 1.5 cm diameter x 2 pcs. stitches with a ribbon for the portion of flower petals. • Ribbon 【Main body】 • Embroidery thread: 1 skein each Outer fabric (Right side) IC-E-21 2/2 Wall Hanging with Embroidery 2. Then, make a pocket. 5. Make tabs. Sew some lace onto the front of the outer fabric of a pocket. Put together the outer and Put together the pocket outer and lining fabrics wrong side out, and stitch them backing fabrics of a tab wrong together leaving an opening for reversing. Once the fabrics are stitched together, side out, and stitch them reverse them right side out and blind stitch the opening. together leaving an opening for reversing. Concealed seam 3 0, 5 Once the fabrics are stitched Lace 3 together, reverse them right side out and blind stitch the opening. opening for Make two of these. reversing 【Tab】 1 【Pocket】 Outer fabric Outer fabric (Right side) (Right side) 【Pocket】 10 【Pocket】 Opening for Outer fabric (Wrong side) Outer fabric (Right side) 4 reversing 【Tab】 Outer fabric 3. Sew the pocket 4. Put together the main-body outer and (Wrong side) 1 onto the main body. lining fabrics with an adhesive interlining on 【Main body】 each back wrong side out, and stitch them Outer fabric (Right side) together leaving an opening for reversing. Once the fabrics are stitched together, reverse them right side out and blind stitch 3 the opening. 6. Sew the tabs onto the 3 Attach the adhesive main body. interlining to the back. As shown in the illustration, sandwich the main body with folded tabs and sew 0, 5 buttons to fix it. 【Main body】 Outer fabric 3 (Right side) Opening for reversing 10 【Main body】 Outer fabric (Wrong side) 1.
Load more

Recommended publications
  • Exempt Services
    County of Somerset New Jersey PO Box 3000 – 20 Grove Street COUNTY ADMINISTRATION BUILDING SOMERVILLE, NJ 08876-1262 PURCHASING DIVISION PHONE: (908) 231-7045 MARY LOUISE STANTON Fax: (908) 575-3917 Purchasing Agent, QPA NOTICE TO BIDDERS #2 SOCCP The County of Somerset is conducting a voluntary Co-operative Pricing System #2 SOCCP. Sealed bids which will be received by the Purchasing Agent acting as Lead Agent on behalf of each participating contracting unit, on January 26, 2010 at 2:30 P.M. prevailing time in the Purchasing Division, County Administration Building, 20 Grove St., Somerville, NJ 08876 at which time and place bids will be opened and read in public for: Uniforms, Various County Departments, Contract #CC-04-10 Proposals must be made on the standard proposal form, in addition to a CD of the Table, be enclosed in a sealed package. Specifications and instruction to bidders may be obtained at the Purchasing Office or the County website at www.co.somerset.nj.us * * All Bid Addenda will be issued on the website. Therefore, all interested respondents should check the website from now through bid opening. It is the sole responsibility of the respondent to be knowledgeable of all addenda related to this procurement. Bidders shall comply with the requirements of N.J.S.A. 10:5-31 and N.J.A.C. 17-27 et seq. Mary Louise Stanton, QPA NOTICE- RESULTS OF ALL BIDS ARE POSTED ON THE COUNTY WEB SITE. 1 CO-OPERATIVE PRICING CONDITIONS METHOD OF AWARDING CONTRACTS Contract(s) of purchase shall be awarded to the lowest responsible bidder(s) as declared by the County of Somerset.
    [Show full text]
  • Embroidery & Sewing Machine
    BABY LOCK Embroidery & Sewing Machine Discover new paths to creativity with the Baby Lock Vesta sewing and embroidery machine. Powered with innovative technology, the Vesta makes every step easier. Create and easily access your own designs or use any of the built-in designs and editing features. Wi-Fi Enabled 6 1/4" x 10 1/4" 293 Built-in 301 Built-in Advanced Needle Embroidery Field Embroidery Designs Stitches Threader BabyLock.com Convenience Features Vesta • Convenient One-Touch Buttons for o Start/Stop Embroidery & Sewing Machine o Reverse Sewing o Needle up/down o Reinforcement Key o Thread cutter • Automatic presser foot lift • Ergonomic hands-free presser foot lift • Low bobbin thread indicator • Needle plate with scale in inches and centimeters • Electronic foot control • Free arm with drop feed lever • Soft cover case with storage 1 1 • Two accessory storage compartments Advanced Needle Threader 6 /4″ x 10 /4″ Embroidery Field • Programmable needle up/down Threading a needle has never been easier than Stitch bigger embroidery designs and enjoy less • Quick-Set Bobbin Winder with this innovative threader. With just a few simple re-hooping with a large embroidery field - motions, your needle is threaded and ready to use - it’s 6 1/4″ x 10 1/4″. Included Accessories so easy, you can do it with one hand! • 13 Feet o Buttonhole o Embroidery o Overcasting o Monogramming o Zipper o Zigzag o Blind stitch o Button fitting o Open toe o Teflon o Stitch guide o Adjustable zipper/piping 293 Built-in Embroidery Designs 301 Built-in Stitches o Free-motion open toe With 293 built-in embroidery designs, you’ll always With 301 built-in stitches, you’ll have many creative • Soft cover for machine find inspiration in the Vesta.
    [Show full text]
  • IBS-5500, Industrial Blind Stitch Sewing Machine
    IBS-5500 INDUSTRIAL BLIND STITCH SEWING MACHINE Original Yamato Sewing Head • One-needle chain stitch blind hem machine with top- and bottom-driven puller • Servo synchronized double puller • Servo synchronized conveyor belt • Full accessibility of the sewing head for Air Pressure Regulator maintenance and service. • Includes two hemmers for single and • Consistent pressure double hems. • Automatic purge Fabric Tension Device Accessible Control Box • CE and UL certified • Festo controller • Servo motors & drives Touchscreen • Touchscreen interface for quick adjustments and easy sewing selections • By pressing the maintenance button on the touch screen, the sewing head lifts out of the machine for full access. Repositionable • Improved mobility • Machine is on wheels and movable after installation TECHNICAL SPECIFICATIONS REQUIREMENTS • Speed: 30 – 40 Panels, bottom and side hems, • Machine Height: upon request, 35.5’’ or • Electric: 240VAC, 3500 W / 110 VAC, 3500 W per hour (average panel length 2500mm / 98’’). 900mm as a standard (levelers can adjust +/- • Air: 7 Bar, 3L Per Cycle • Conveyor Length: 5500mm / 217’’ ½ inch or 12mm) • Conveyor Width: 1000mm / 39.5’’ • Total Weight: 600kg / 1320lbs • Machine Width: 1600mm / 63’’ A GLOBAL LEADER IN WINDOW TREATMENT MANUFACTURING AUTOMATION Joos Advanced Technology builds state-of-the-art industrial machines to create efficient, cost-saving, automated production processes. Our advanced technology has made us a global leader in supplying innovative equipment for the shades, blinds, and curtains industry for over 20 years. Our machines have been installed in over 20 countries around the world as the industry demand for our equipment continues to increase. 900 W. DIGGINS STREET | HARVARD, ILLINOIS 60033 USA +1.864.573.2700 JOOSTECHNOLOGY.COM.
    [Show full text]
  • CO Guide to Judging Clothing
    Colorado 4-H Guide for Clothing Judges Standards of Quality Clothing Construction Introduction One of our basic tasks in evaluating or judging is to be able to recognize and identify the standards that give a garment a finished, professional look. There are many techniques that can be used to accomplish the same end product. Each of us has techniques that we like and techniques that we dislike. In an objective evaluation it is essential to play down our personal preferences and to build upon identified and accepted standards. In general, there are some standards that apply to almost all techniques. Almost all construction techniques should result in an area, finish or detail that is: • Inconspicuous o Flat and smooth o Free from bulk o Stitching a uniform distance from an edge or fold • Functional • Durable –stitching uniform and secure Specific standards that can be expected in good construction are listed on the following pages. They are organized by techniques and/or areas, and the techniques are presented in alphabetical order. Overall Appearance Be objective when considering the overall appearance and appeal of a garment. It may be helpful to think about there being at least one especially pleasing feature about this garment, reflecting the many hours of though, effort and creativity that went into its construction. It may be the design, fabric, use of unusual technique or detail. Particularly neat and well-done machine or handstitching, etc. o Overall neatness and cleanliness o Plaids, stripes, checks and other designs matched at seams o Fabric with a direction in design or nap issued in garment in one direction unless garment design requires variation.
    [Show full text]
  • Assembling Technologies for Functional Garments—An Overview
    Indian Journal of Fibre & Textile Research Vol. 36, December 2011, pp.380-387 Assembling technologies for functional garments—An overview Prabir Janaa National Institute of Fashion Technology, Gulmohar Park, New Delhi 110 016, India Functional garments have higher functional properties and lesser aesthetic properties. They can be workwear, active sportswear, medical wear, personal protective garments, and smart garments. The fibre contents used are mainly polyester, polyethylene, kevlar, and spandex blends which can be woven, knitted and nonwoven, albeit the list is increasing day by day to include speciality fibres like bamboo, banana to name a few. These garments are made up by joining several pattern pieces together and the pieces, in turn, are joined with accessories comprising membranes, linings, buttons, zippers, tapes and waddings to create a composite garment. While fabric can be joined by sewing, seam welding or bonding technique, accessories can be joined by sewing, welding, pasting or using combination method. Some functional garments are made seamless thus requiring little or no assembling technologies. Different new technologies for joining fabric pieces and assembling of accessories have been explored so far. There is a distinct shift towards use of welding and bonding technologies in functional clothing because of the reduced bulk and weight, cleaner appearance and sealing qualities offered by them. Some challenges still continue to exist. This paper reports the distinguished characteristics and developments in assembling technologies, such as sewing, welding and bonding along with the challenges ahead in this area. Keywords: Assembling technology, Bonding, Garment, Sewing, Welding 1 Introduction psychological factors such as potential for According to Cambridge dictionary ‘functional’ claustrophobia or distraction from work3.
    [Show full text]
  • Endless Binding Ann Anderson, Quiltwoman.Com My Usual Binding Uses 2” Strips of Fabric Cut Across Making Mitered Corners the Width of the Fabric (WOF)
    Endless Binding Ann Anderson, Quiltwoman.com My usual binding uses 2” strips of fabric cut across Making Mitered corners the width of the fabric (WOF). I cut the binding strips Fold strip up forming a 45° angle. Next fold the strip wider for thick quilts such as those made from flannel. back down and sew from edge to 1/4” from next corner. Repeat until you are back on the first edge. If the edges of the quilt are curved, as in a double Fold up Fold down, wedding ring, the strips should be cut on the bias and aligning edges. this technique would not be appropriate. Start sewing at edge and stop 1/4" from The binding is machine sewn to the front and hand bottom edge. sewn to the back. Joining Final Ends of Binding Strips How much to cut? Overlap the ends of the binding strips by 2"** and Measure the total length of all the edges (usually trim. Unfold the ends of the binding strips. Put right 4) and add about 10". Divide that number by 40" to sides together and sew a diagonal seam. determine the number of 2" x WOF strips to cut. Sewing line Unfolded wrong side For example, if your quilt is 60" x 80", you need 2" overlap Unfolded showing 2 x 60" + 2 x 80" + 10" or 290". Divide by 40" per strip and that is 7 1⁄4 strips. I would just cut 8 strips. Sewing Strips Together Sew strips together with diagonal seams. Press the seams open for a smoother, less bumpy binding.
    [Show full text]
  • Instruction Manual for Sewing Machine
    f2D /3a INSTRUCTION MANUAL FOR I SEWING MACHINE EL3-1© j WHITE’ _____________________________________ WHITE SEWING MACHINE COMPANY Record in space provided below the Serial No. and Model No. of this appliance. The Serial No. is located on Bed Plate. The Model No. is located on Rating Plate. Serial No. Model No. Retain these numbers for future reference. 21&22 CONTENTS Name of Parts 1 & 2 Accessories 3 Before sewing (Power supply and Sewing lamp) 4 Take out extension table, free arm sewing 5 Winding the bobbin 6 Removing bobbin case and bobbin 7 Inserting bobbin into bobbin case 7 Inserting bobbin case into shuttle race 8 Threading upper thread & Twin needle threadg. 9 Drawing up bobbin thread 10 Changing sewing directions 10 Control dial & Adjusting thread tension 11&12 Regulating the presser foot pressure 13 Drop feed 13 Changing needle 14 Fabric. Thread. Needle table 15 Sewing (pattern selector) and operation table 16 To start sewing 17 To finish seam 18 Straight stitch 19 Zigzag sewing 19 Overcasting 20 Stretch stitch 20 Blind stitch Button sewing 23 Binding 23 Zipper sewing 24 Button hole sewing 25 Hemming 26 Twin Needle 27 Embroidery 27 Quilter 28 Seam guide 28 Maintenance (Cle.ning and oiling) 29 Checking Performance Problems WHAT TO DO 30 NAME OF PARTS (FRONT VIEW) 1 Pattern selector dial 8 Sub-spool pins 2 Pressure regulator 9 Top cover 3 Take up lever 10 Zigzag width dial 4 Thread tension dial 1 1 Stitch length dial 5 Presser foot 12 Reverse button 6 Shuttle cover 13 Thread guide for upper 7 Extension table threading —1— (REAR VIEW) Bobbin winder spindle Bobbin winder stopper Upper thread guide Stop Motion knob Hand wheel Face cover Thumb screw Needle plate Presser foot lever —2— ACCESSOR I ES / Bobbin Felt Zigzag foot Button hole (On machine) foot Button foot Machine Oil / Zipper foot 0 Button hole cutter Screw driver Needle #11 #14 —3— BEFORE SEWING 1.
    [Show full text]
  • Serger Techniques
    Serger Techniques Table of Contents Balanced Serger Stitches ....... ..... .. .... 1 Flatlock Applique .... .......... ...... .. .. .. ....6 Four-Thread Serg ing .. .......... .... .. .... .. 1 Decorative Lace Reinforcing Tape Application .......... 1 and Tape Application .... .......... .. .. ..... .7 Soft Gathering ............ .... ... ... ..... .. .....2 Rolled Edge .... .. ..... ....... ...... ......... .. ..... 7 Three-Thread Se rging ...... ... ..... ........ 2 Napkin Fin ish Rolled Edge ............... .8 Edge Hemming and Finishing .... ... ... 2 Tablecloth Edging .... ... .............. ... .. ....8 Lingerie Seams ......... ............. ......... ... 3 Formal and Bridal Wear ..... .... .. ... .. ....9 Lace Joining ...... ........ ............. .... .. ..... 3 Scarf Edge Rolled Hem ....... .... ... ....... .9 Multipurpose Guide Foot .... ... ..... .... 4 Spaghetti Straps .. .. ....... .... .... ... .. ........ 9 Durable Three-Thread Blind Hem .... 4 Fabric Flowers ... ... ... ....... ..... .... .. ...... 1O Decorative Serging ...... ..... .... ...... ... .... 4 Stitch Variations - Heirloom .... .... .. 10 Decorative Thread Serging .. ....... ... .5 Pin Tucking .. ....... .. ....... .. ............... ... 11 Basic Three-Thread Flatlock .... .. ... .... .5 Heirloom Lace Insertion ..... ........... .. 11 Flatlock Topstitching ... .... ....... ..........6 Gathering Foot Quick Start Guide .... 12 Balanced Serger Stitches • Balanced stitches are used in construction applications such as seams, overcasting, edgings and finishes. • A
    [Show full text]
  • Binding: Something Even Lily Does Once in a While
    Binding: Something even Lily does once in a while. Binding on a quilt is the small edging that wraps from front to back, enclosing the raw crust of your quilt sandwich in a nice, finished way. Many people refer to this as a border, or edging, or other terms, but the term “binding” makes it clear to anyone who might be helping you that you are referring specifically to the final step in finishing your quilt. Why bind? You may ask. Some alternatives to binding are flip and sew (when you put the right sides of the quilt and back together, sew around the edge, flip it right sides out, and hand stitch the small opening you left; or bringing the back around to the front and stitching it down. You can finish your quilts like this, and sometimes that's appropriate, but I will say, even as someone who hates binding, there are a couple really good reasons to bind your quilt. The most important questions you should ask yourself when preparing to finish your quilt sandwich is “How long do I want this to last?” followed closely by “How do I want this to look?” I most often hear people want to flip and sew or pull the back around for kids' quilts, citing the fact that it will be dragged around and washed extensively. Well, while we often think that a kids' quilt is not an heirloom or something you want to spend loads of time on, for many a child (this one included), a beloved “baby blankie” might be the center of their very existence for sometime, and then tucked away in a box when all that remains is tatters.
    [Show full text]
  • Developing Fall-Impact Protection Pad with 3D Mesh Curved Surface Structure Using 3D Printing Technology
    polymers Article Developing Fall-Impact Protection Pad with 3D Mesh Curved Surface Structure Using 3D Printing Technology Jung Hyun Park and Jeong Ran Lee * Department of Clothing and Textiles, Pusan National University, Busan 46241, Korea; [email protected] * Correspondence: [email protected]; Tel.: +82-51-510-2841 Received: 9 October 2019; Accepted: 30 October 2019; Published: 1 November 2019 Abstract: In this study, we present the development of fall-impact protection pads for elderly people using three-dimensional (3D) printing technology. To develop fall-impact protection clothing, it is important to maintain the functionality of the protection pad while ensuring that its effectiveness and appearance remain optimal in the process of inserting it. Therefore, this study explores the benefit of exploiting 3D scan data of the human body using 3D printing technology to develop a fall-impact protection pad that is highly suited to the human body shape. The purpose of this study was to present a 3D modeling process for creating curved protective pads comprising a hexagonal mesh with a spacer fabric structure and to verify the impact protection performance by printing curved pads. To this end, we set up a section that includes pads in the 3D human body scan data and extracted body surface information to be applied in the generation of the pad surface. The sheet-shaped hexagonal mesh structure was cut and separated according to the pad outline, and then deformed according to the curved surface of the human body. The pads were printed, and their protection performance was evaluated; a 79.2–81.8% reduction in impact force was observed compared to similar cases in which the pads were not used.
    [Show full text]
  • A Manual for Home Sewing
    Extension Bulletin 468 December 1933 Home Economics Series A Manual for Home Sewing 41, THIS BULLETIN IS PREPARED TO SERVE THREE GROUPS OF OREGON HOME- MAKERS THOSE WHO HAVE LITTLE EX- PERIENCE IN HOME SEWING AND WHO FIND IT ECONOMICAL TO MAKE MUCH OF THE FAMILY'S CLOTHING. THE MORE EXPERIENCED WHO DESIRE A READY REF- ERENCE ON HOME SEWING. THOSE FAM- ILIES WHO AT THIS TIME ARE UNDER THE NECESSITY OF RECEIVING CLOTH- ING FROM THEIR FEDERAL AND STATE GOVERNMENT. 41, IT IS HOPED THAT THE DIRECTIONS MAY BE FOUND HELP- FUL IN THE PROGRAM OF SELF-HELP AND HOME-MADE LIVING IN WHICH A LARGE PROPORTION OF THESE CITIZENS DESIRE TO PARTICIPATE. Oregon State Agricultural College Extension Service Corvallis, Oregon Cooperative Extension Work in Agriculture and Home Economics Paul V. Maria, Director Oregon State Agricultural College and United States Department of Agriculture, Cooperating Printed and distributed in furtherance of the Acts of Congress of May 8 and June dO, 1914 TABLE OP CONTENTS Page Sewing Equipment and Technique 3 Sewing Machine 3 Other Equipment 4 Pressing Equipment 6 Seams and Seam Finishes 7 Plain Seams and Finishes 7 Special Seams 8 Hems and Hemstitches 10 Stitches Used in Hems 10 Hems and Hem Finishes 11 Mitered Corners 14 Fabric Buttonholes 15 Pockets 18 Plackets 22 Bindings, Pipings, and Folds 24 Preparation of Bias 25 Bindings 25 Pipings 26 French Fold 26 Plaits 27 Fastenings 27 Garment Repair 29 Darning 29 Patching 30 Index 32 A Manual for Home Sewing By AZALEA SAGER Extension Specialist in Clothing and Textiles and satisfaction are the two chief reasons for making or ECONOMYremodeling garments at home.
    [Show full text]
  • 1895 Reissue 41 Style 11
    Style 9: 1893 40 New Johnston ruffler (Figure 41b, page 21), Style 8 tuck- marker. Style 10: 1895 reissue 41 New ruffler Figures 44a to 44c page 22), and Style 8 tuck- marker. Style 11: 1899 reissue 42 New ruffler (as in Figure 40c, page 20, but with the spacer) and Style 8 tuck-marker. Three different Style 11 sets are documented, but they are all dated after the Style 12 set! All three style 11 manuals describe a foot hemmer, but none of the box illustrations or the lists of attachments include it. As I think it is likely that Singer produced sets chronologically this reissue suggests that there is at least one other, earlier style 11 set. 40 Singer, 1893b. 41 Singer, 1895a. 42 Singer, 1899. 29 Style 11: 1901 reissue 43 New tuck-marker on page 14 of the instruction manual. (The illustration on page 15 of the manual and the box view opposite show the 1899 tuck-marker, probably because the drawing was copied from the previous manual. Both are given the same number of 26513.) This Style manual includes a price list. A “box with racks” is the folding box with the holding clips but without any attachments or accessories. Style 11: 1906 reissue 44 A different arrangement of the accessories (screwdrivers, and so on). Otherwise the same as the above, including the two different tuck-markers that are given the same number of 26513. It is one of the most common folding boxes. This Style manual has a price list. 45 Style 12: 1895 reissue This Style manual includes a list of contents.
    [Show full text]