DOCSLIB.ORG

Fahrenheit 1 Fahrenheit

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Fahrenheit 1 Fahrenheit Fahrenheit 1 Fahrenheit Fahrenheit is the temperature scale proposed in 1724 by, and named after, the physicist Daniel Gabriel Fahrenheit (1686–1736). Today, the temperature scale has been replaced by the Celsius scale in most countries.[1] It is still in use in few nations, such as United States and Belize.[2] Thermometer with Fahrenheit units on the outer scale and Celsius units on the inner scale Definition and conversions Fahrenheit temperature conversion formulae from Fahrenheit to Fahrenheit Celsius [°C] = ([°F] − 32) × 5 [°F] = [°C] × 9 + 32 ⁄9 ⁄5 Kelvin [K] = ([°F] + 459.67) × 5 [°F] = [K] × 9 − 459.67 ⁄9 ⁄5 Rankine [°R] = [°F] + 459.67 [°F] = [°R] − 459.67 For temperature intervals rather than specific temperatures, 1 °F = 1 °R = 5 °C = 5 K ⁄9 ⁄9 Comparisons among various temperature scales On the Fahrenheit scale, the freezing point of water is 32 degrees Fahrenheit (°F) and the boiling point 212 °F (at standard atmospheric pressure), placing the boiling and freezing points of water exactly 180 degrees apart.[3] A degree on the Fahrenheit scale is 1⁄ of the interval between the freezing point and the boiling point. On the Celsius 180 scale, the freezing and boiling points of water are 100 degrees apart. A temperature interval of 1 degree Fahrenheit is equal to an interval of 5⁄ degrees Celsius. The Fahrenheit and Celsius scales converge at −40 degrees (i.e. −40 °F 9 and −40 °C represent the same temperature).[3] Absolute zero is −459.67 °F.[4] The Rankine temperature scale was created to use degree intervals the same size as those of the Fahrenheit scale, such that a temperature difference of one degree Rankine (1 °R) is equal to a difference of 1 °F, except that absolute zero is 0 °R – the same way that the Kelvin temperature scale matches the Celsius scale, except that absolute zero is 0 K. Fahrenheit 2 History According to an article Fahrenheit wrote in 1724,[5] he based his scale on three reference points of temperature. The zero point is determined by placing the thermometer in brine: he used a mixture of ice, water, and ammonium chloride, a salt. This is a frigorific mixture which automatically stabilizes its temperature at 0 °F. A mixture of ice and water stabilizes, either freezing or melting at 32 °F,[6] though Fahrenheit did not use this point in defining his temperature scale. The third point, 96 degrees, was the level of the liquid in the thermometer when held in the mouth or under the armpit of his wife. Fahrenheit noted that, using this scale, mercury boils at around 600 degrees. Later, work by other scientists observed that water boils about 180 degrees higher than the freezing point and decided to redefine the degree slightly to make it exactly 180 degrees higher.[5] It is for this reason that normal body temperature is 98.6 on the revised scale (whereas it was 96 on Fahrenheit's original scale).[7] According to a letter Fahrenheit wrote to his friend Herman Boerhaave,[8] his scale was built on the work of Ole Rømer, whom he had met earlier. In Rømer’s scale, the two fixed reference points are that brine also freezes at 0 degrees and water boils at 60 degrees. He observed that, on this scale, water freezes at 7.5 degrees. Fahrenheit multiplied each value by four in order to eliminate fractions and increase the granularity of the scale (resulting in 30 and 240 degrees, respectively). He then re-calibrated his scale between the freezing point of water and normal human body temperature (which he observed to be 96 degrees); he adjusted the scale so that the melting point of ice would be 32 degrees, so that 64 intervals would separate the two, allowing him to mark degree lines on his instruments by simply bisecting the interval six times (since 64 is 2 to the sixth power).[9] Usage The Fahrenheit scale was the primary temperature standard for climatic, industrial and medical purposes in some English-speaking countries until the 1960s. In the late 1960s and 1970s, the Celsius (known until 1948 as centigrade) scale was adopted by most of these countries as part of the standardizing process called metrication. The Fahrenheit scale is used in the United States, Palau, Belize[2] , Burma, and Liberia[10] for non-scientific applications. Most other countries have adopted Celsius as the primary scale in all use. In the U.S., weather forecasts, food cooking and freezing temperatures are commonly in degrees Fahrenheit. Various reasons are given for the resistance to the Celsius system in the U.S., including the larger size of each degree Celsius (resulting in the need for decimals where integer Fahrenheit degrees were adequate for much technical work), or the lower zero point in the Fahrenheit system which reduces the number of negative signs when measurements such as weather data were averaged.[11] On the other hand, most countries using the Fahrenheit system, like New Zealand or Australia, have totally switched to the Celsius system.[12] Even though in Canada weather is always reported in degrees Celsius, many outdoor thermometers display temperatures in both Fahrenheit and Celsius. Inside buildings, digital or analogue thermostats may be either in Fahrenheit or Celsius, and kitchen ovens are in both degrees Fahrenheit and degrees Celsius. In the United Kingdom the weather is usually reported in both Celsius and Fahrenheit due to many of the older generation of Britons who do not understand Celsius. Representation The Fahrenheit symbol has its own Unicode character: "℉" (U+2109). This is a compatibility character encoded for roundtrip compatibility with legacy CJK encodings (which included it to conform to layout in square ideographic character cells) and vertical layout. Use of compatibility characters is discouraged by the Unicode Consortium. The ordinary degree sign (U+00B0) followed by the Latin letter F ("°F") is thus the preferred way of recording the symbol for degree Fahrenheit. Fahrenheit 3 Temperatures and intervals As with the Celsius scale, the same symbol, °, is used to denote both a point on the temperature scale, with a letter (C, F) indicating which scale is being used (e.g. "Gallium melts at 85.5763 °F"), and to denote a difference between temperatures or an uncertainty of temperature (e.g. "The output of the heat exchanger is hotter by 72 °F" and "Our standard uncertainty is ±5 °F"). See also • Comparison of temperature scales References [1] "Metric usage and metrication in other countries" (http:/ / lamar. colostate. edu/ ~hillger/ internat. htm). Retrieved December 11, 2009. [2] "Belize Weather Bureau" (http:/ / www. hydromet. gov. bz/ ). Retrieved May 9, 2008. [3] Conversion of Temperature (http:/ / www. mathsisfun. com/ temperature-conversion. html) [4] Temperature Units Converter (http:/ / www. unitarium. com/ temperature) [5] "Fahrenheit temperature scale" (http:/ / www. sizes. com/ units/ temperature_Fahrenheit. htm). Sizes, Inc. December 12, 2006. Retrieved May 9, 2008. [6] Muller, R.A. (2009). Physics for Future Presidents (http:/ / physics. berkeley. edu/ academics/ Courses/ physics10/ teaching/ Physics10/ PffP_textbook_F08/ PffP-02-heat-F08. pdf). pp. 2–5, 2–17. Retrieved 20 February 2010. [7] Elert, Glenn; Forsberg, C; Wahren, LK (2002). "Temperature of a Healthy Human (Body Temperature)" (http:/ / hypertextbook. com/ facts/ LenaWong. shtml). Scandinavian Journal of Caring Sciences 16 (2): 122. doi:10.1046/j.1471-6712.2002.00069.x. PMID 12000664. Retrieved 2008. [8] Ernst Cohen and W. A. T. Cohen-De Meester. Chemisch Weekblad, volume 33 (1936), pages 374–393, cited and translated in http:/ / www. sizes. com:80/ units/ temperature_Fahrenheit. htm [9] Cecil Adams. "On the Fahrenheit scale, do 0 and 100 have any special significance?" (http:/ / www. straightdope. com/ classics/ a4_188. html). The Straight Dope. [10] CIA Factbook: Weights and Measures (https:/ / www. cia. gov/ library/ publications/ the-world-factbook/ appendix/ appendix-g. html) [11] (http:/ / books. google. com/ books?id=xRMPAAAAYAAJ& pg=PA165& dq=centigrade+ too+ large& lr=& as_brr=0& as_pt=ALLTYPES#PPA166,M1) Halsey, Frederick A., Dale, Sanuel S., "The metric fallacy," The American institute of weights and measures, Second Edition, 1919. Pages 165-166, 176-177. Retrieved May 19, 2009 [12] (http:/ / nomorewinter. com/ nzinfo/ moneyandmetrics. htm) Information about New Zealand's money and metric measures Article Sources and Contributors 4 Article Sources and Contributors Fahrenheit Source: http://en.wikipedia.org/w/index.php?oldid=372639486 Contributors: .:Ajvol:., 152.163.207.xxx, 171046, 5 albert square, 80.255, ACBest, AdultSwim, Aitias, Aka042, Alaiche, Alandeus, Alansohn, Alfio, [email protected], AllenSalyer, Alphachimp, Altenmann, Amorymeltzer, Angrysockhop, Antandrus, Antares784, Antman, Anturiaethwr, Aoi, Archon Divinus, ArglebargleIV, Asdirk, AstroNomer, Astrochemist, Aucitypops, AxSkov, AxelBoldt, Bbatsell, Bedford, Beland, Belovedfreak, BenFrantzDale, Beno1000, Betterusername, BigDunc, Biruitorul, BlueEarth, Bob Jonkman, Bobbean52, Bobblewik, Bobo192, Boettern, Bogog, Boing! said Zebedee, Bongwarrior, Boomshanka, Bucephalus, Buenotaco55, Butros, Bwhack, CMacMillan, Caerwine, Caesura, Camw, Capricorn42, Captain-tucker, CardinalDan, Cautious, Cdc, CesarB, Chris 73, Christian List, Chunkylefunga, Ckape, Ckatz, Classical geographer, Conversion script, Coolcat420, Coolhandscot, Courcelles, Cpt ricard, Crissov, Cvos, CyberShadow, Cybercobra, Cyde, DOSGuy, Dan Sarandon, Danielkueh, Danny, Dannycas, Dantheman531, DarrenBaker, David H Braun (1964), David spector, DavidJ710, Delldot, Derek Ross, Diagonalfish, Didactohedron,
Load more

Recommended publications
  • Guide for the Use of the International System of Units (SI)
    Guide for the Use of the International System of Units (SI) m kg s cd SI mol K A NIST Special Publication 811 2008 Edition Ambler Thompson and Barry N. Taylor NIST Special Publication 811 2008 Edition Guide for the Use of the International System of Units (SI) Ambler Thompson Technology Services and Barry N. Taylor Physics Laboratory National Institute of Standards and Technology Gaithersburg, MD 20899 (Supersedes NIST Special Publication 811, 1995 Edition, April 1995) March 2008 U.S. Department of Commerce Carlos M. Gutierrez, Secretary National Institute of Standards and Technology James M. Turner, Acting Director National Institute of Standards and Technology Special Publication 811, 2008 Edition (Supersedes NIST Special Publication 811, April 1995 Edition) Natl. Inst. Stand. Technol. Spec. Publ. 811, 2008 Ed., 85 pages (March 2008; 2nd printing November 2008) CODEN: NSPUE3 Note on 2nd printing: This 2nd printing dated November 2008 of NIST SP811 corrects a number of minor typographical errors present in the 1st printing dated March 2008. Guide for the Use of the International System of Units (SI) Preface The International System of Units, universally abbreviated SI (from the French Le Système International d’Unités), is the modern metric system of measurement. Long the dominant measurement system used in science, the SI is becoming the dominant measurement system used in international commerce. The Omnibus Trade and Competitiveness Act of August 1988 [Public Law (PL) 100-418] changed the name of the National Bureau of Standards (NBS) to the National Institute of Standards and Technology (NIST) and gave to NIST the added task of helping U.S.
    [Show full text]
  • TEMPERATURE © 2019, 2008, 2004, 1990 by David A
    TEMPERATURE © 2019, 2008, 2004, 1990 by David A. Katz. All rights reserved. A BRIEF HISTORY OF TEMPERATURE MEASUREMENT Ancient people were physically aware of hot and cold and probably related temperature by the size of the fire needed, and how close to sit, to keep warm. An Australian tribe, still primitive, uses dogs instead of blankets to keep warm, thus, they can relate temperature by the dog. (See Figure 1.) A moderately cool night may require two dogs to keep warm, thus it is a two-dog night. An icy night would be a six-dog night. Early people were, at first, fire tenders, maintaining fires originally Figure 1. Australian started by natural causes. Later, they learned how to make fire and aborginies use dogs became fire makers. Eventually, they became fire managers as they to keep warm. learned to work with fire to gain the heat needed to boil water, cook meat, fire pottery (500°F or 257°C), work with copper, tin, bronze (an alloy of copper and tin) and iron, and to make glass. (See Figure 2) Although they had no quantitative measuring devices to determine how hot a fire was, they developed recipes for building different types of fires and probably used a physical indicator, such as some mineral or metal melting, to indicate the correct Figure 2. Early people temperature for a particular process. used fire to cook food and later to work with The ancient Greeks knew that air expanded when heated and metals. applied the principle mechanically, but they developed no means of measuring temperature or amount of heat needed and devised no measuring instruments.
    [Show full text]
  • Thermodynamic Temperature
    Thermodynamic temperature Thermodynamic temperature is the absolute measure 1 Overview of temperature and is one of the principal parameters of thermodynamics. Temperature is a measure of the random submicroscopic Thermodynamic temperature is defined by the third law motions and vibrations of the particle constituents of of thermodynamics in which the theoretically lowest tem- matter. These motions comprise the internal energy of perature is the null or zero point. At this point, absolute a substance. More specifically, the thermodynamic tem- zero, the particle constituents of matter have minimal perature of any bulk quantity of matter is the measure motion and can become no colder.[1][2] In the quantum- of the average kinetic energy per classical (i.e., non- mechanical description, matter at absolute zero is in its quantum) degree of freedom of its constituent particles. ground state, which is its state of lowest energy. Thermo- “Translational motions” are almost always in the classical dynamic temperature is often also called absolute tem- regime. Translational motions are ordinary, whole-body perature, for two reasons: one, proposed by Kelvin, that movements in three-dimensional space in which particles it does not depend on the properties of a particular mate- move about and exchange energy in collisions. Figure 1 rial; two that it refers to an absolute zero according to the below shows translational motion in gases; Figure 4 be- properties of the ideal gas. low shows translational motion in solids. Thermodynamic temperature’s null point, absolute zero, is the temperature The International System of Units specifies a particular at which the particle constituents of matter are as close as scale for thermodynamic temperature.
    [Show full text]
  • The International System of Units (SI) - Conversion Factors For
    NIST Special Publication 1038 The International System of Units (SI) – Conversion Factors for General Use Kenneth Butcher Linda Crown Elizabeth J. Gentry Weights and Measures Division Technology Services NIST Special Publication 1038 The International System of Units (SI) - Conversion Factors for General Use Editors: Kenneth S. Butcher Linda D. Crown Elizabeth J. Gentry Weights and Measures Division Carol Hockert, Chief Weights and Measures Division Technology Services National Institute of Standards and Technology May 2006 U.S. Department of Commerce Carlo M. Gutierrez, Secretary Technology Administration Robert Cresanti, Under Secretary of Commerce for Technology National Institute of Standards and Technology William Jeffrey, Director Certain commercial entities, equipment, or materials may be identified in this document in order to describe an experimental procedure or concept adequately. Such identification is not intended to imply recommendation or endorsement by the National Institute of Standards and Technology, nor is it intended to imply that the entities, materials, or equipment are necessarily the best available for the purpose. National Institute of Standards and Technology Special Publications 1038 Natl. Inst. Stand. Technol. Spec. Pub. 1038, 24 pages (May 2006) Available through NIST Weights and Measures Division STOP 2600 Gaithersburg, MD 20899-2600 Phone: (301) 975-4004 — Fax: (301) 926-0647 Internet: www.nist.gov/owm or www.nist.gov/metric TABLE OF CONTENTS FOREWORD.................................................................................................................................................................v
    [Show full text]
  • Temperature and Temperature Scales
    Temperature and Temperature Scales Ck12 Science Say Thanks to the Authors Click http://www.ck12.org/saythanks (No sign in required) AUTHOR Ck12 Science To access a customizable version of this book, as well as other interactive content, visit www.ck12.org CK-12 Foundation is a non-profit organization with a mission to reduce the cost of textbook materials for the K-12 market both in the U.S. and worldwide. Using an open-content, web-based collaborative model termed the FlexBook®, CK-12 intends to pioneer the generation and distribution of high-quality educational content that will serve both as core text as well as provide an adaptive environment for learning, powered through the FlexBook Platform®. Copyright © 2013 CK-12 Foundation, www.ck12.org The names “CK-12” and “CK12” and associated logos and the terms “FlexBook®” and “FlexBook Platform®” (collectively “CK-12 Marks”) are trademarks and service marks of CK-12 Foundation and are protected by federal, state, and international laws. Any form of reproduction of this book in any format or medium, in whole or in sections must include the referral attribution link http://www.ck12.org/saythanks (placed in a visible location) in addition to the following terms. Except as otherwise noted, all CK-12 Content (including CK-12 Curriculum Material) is made available to Users in accordance with the Creative Commons Attribution-Non-Commercial 3.0 Unported (CC BY-NC 3.0) License (http://creativecommons.org/ licenses/by-nc/3.0/), as amended and updated by Creative Com- mons from time to time (the “CC License”), which is incorporated herein by this reference.
    [Show full text]
  • Article on Temperature and Temperature Scales
    Article on Temperature and Temperature Scales The temperature of a substance is the degree of hotness or coldness of the substance. A hot substance is said to have a high temperature whereas a cold substance is said to have a low temperature. Therefore, the temperature of a substance is an indication of the average kinetic energy of the molecules of the substance. Heat always flow from a body at higher temperature to the body at lower temperature. So, we can also say that temperature of a body is the property which governs the flow of heat. It can easily be demonstrated as follows: When two objects of the same material are placed together, the object with higher temperature cools while the cooler object gets warmer until a point is reached after which no more changes occurs. THERMAL EQUILIBRIUM Heat energy flows from a body at higher temperature to another body at lower temperature. In other words, heat flows from a hotter to the colder body. The heat energy keeps flowing from the hotter to the cooler body until the temperature of both the bodies become equal. At this stage, the two bodies are said to be in thermal equilibrium. When two bodies attain the same temperature, they are said to be in thermal equilibrium with each other because then no heat flows from one body to another. The temperature thus reached is called as equilibrium temperature. Therefore, now we can say that Temperature is that quantity which is same for both the system when they are in thermal equilibrium. ZEROTH LAW OF THERMODYNAMICS ZEROTH law of thermodynamics state that "If two systems are separately in thermal equilibrium with a third, then they must also be in thermal equilibrium with each other, and they all have the same temperature regardless of the kind of the system they are." This law can be restated as follows: If there are three or more than three systems which when taken together are in thermal contact and in thermal equilibrium as well, then any of the two system taken together are in equilibrium with one another.
    [Show full text]
  • Temperature Scales
    Temperature Scales Temperature is the level of heat in a gas, liquid, or solid. Three scales are commonly used for measuring temperature. The Celsius and Fahrenheit scales are the most common. The Kelvin scale is primarily used in scientific experiments. Celsius Scale The Celsius scale was invented in 1742 by the Swedish astronomer, Anders Celsius. This scale divides the range of temperature between the freezing and boiling temperatures of water into 100 equal parts. You will sometimes find this scale identified as the centigrade scale. Temperatures on the Celsius scale are known as degree Celsius (ºC). Fahrenheit Scale The Fahrenheit scale was established by the German-Dutch physicist, Gabriel Daniel Fahrenheit, in 1724. While many countries now use the Celsius scale, the Fahrenheit scale is widely used in the United States. It divides the difference between the melting and boiling points of water into 180 equal intervals. Temperatures on the Fahrenheit scale are known as degree Fahrenheit (ºF). Kelvin Scale The Kelvin scale is named after William Thompson Kelvin, a British physicist who devised it in 1848. It extends the Celsius scale down to absolute zero, a hypothetical temperature characterized by a complete absence of heat energy. Temperatures on this scale are called Kelvins (K). Converting Temperatures It is sometimes necessary to convert temperature from one scale to another. Here is how to do this. 1. To convert from ºC to ºF, use the formula: ºF = ºC x 1.8 + 32. 2. To convert from ºF to ºC, use the formula: ºC = (ºF-32) ÷ 1.8. 3. To convert from K to ºC, use the formula: ºC = K – 273.15 4.
    [Show full text]
  • Fahrenheit Scale the First Modern Thermometer, the Mercury Thermometer with a Standardized Scale, Was Invented by Dutch Inventor, Daniel Fahrenheit in 1714
    Origin of temperature scales Review text: page 62 - 62 Galileo Galilei invented a rudimentary water thermoscope in1593, which for the first time allowed temperature variations to be measured. It was a container filled with bulbs of varying mass, each with a temperature marking, the buoyancy of water changes with temperature, some of the bulbs sink while others float, the lowest bulb indicated the temperature. In 1612, the Italian inventor Santorio became the first inventor to put a numerical scale on his thermoscope. It was the first crude clinical thermometer and was designed to be placed in a patient's mouth for temperature taking. Fahrenheit Scale The first modern thermometer, the mercury thermometer with a standardized scale, was invented by Dutch inventor, Daniel Fahrenheit in 1714. Temperature scales require points of reference. In 1714 Daniel Fahrenheit built his scale on the work of Ole Rømer, whom he had met and discussed concepts of scales. With Rømer's scale, salt brine freezes at zero, water freezes and melts at 7.5 degrees, body temperature is 22.5, and water boils at 60 degrees. Fahrenheit multiplied each value by four in order to eliminate fractions. Hence, water freezes and melts at 32 degrees, body temperature is 90, and water boils at 240 degrees. Only 32° F (0° C) is accurate in a modern context Fahrenheit chose the temperature of the body temperature of a healthy person (Fahrenheit`s healthy person happened to be his wife) which he measured in the armpit at 96°. After Fahrenheit died, his successors used the boiling point of water to calibrate the thermometers.
    [Show full text]
  • Everything About Temperature-TD
    EVERYTHING YOU EVER WANTED TO KNOW ABOUT TEMPERATURE By Granpa Curmudgeon There are five — count them — five temperature scales: Kelvin (oK) - after William Thompson Kelvin, 1st Baron Kelvin, who had cold feet (an occupational hazard of living in Belfast, especially 100 years ago). He did a lot of things, some of which were useful, and in his honour the Kelvin scale of absolute temperature (related to Celsius) was named for him. Things all start at 0o K. and go up from there. Rankine (oR) - after William John Macquorn Rankine. Rankine was born in Edinburgh, died in Glasgow, and cared about thermodynamics between times. The Rankine scale uses the smaller Fahrenheit degree for measurement - appropriate for a frugal Scot - and is another absolute temperature scale, as if we needed two of them. Celsius (oC) - formerly, and more appropriately, 'centigrade', but Anders Celsius needed to have something named after him, too, so there you are. Fahrenheit (oF) - after Daniel Gabriel Fahrenheit, who somehow got the idea that water froze at 32 degrees and boiled at something higher. I don't know what he was on, but I could use some. Rèaumur (oRè) - after René-Antoine Ferchault de Rèaumur, who fiddled around with thermometers while waiting for his potage du jour to cool. Well, he had to do something. All these people are dead, now. This is old news, but good. THE BASIC AND UNDYING RELATIONSHIP OF ALL THESE SILLY THINGS TO EITHER OTHER x oK = (x-273.15) oC = (1.25)(x-273.15) oRè = (1.8)x -459.67 oF = (1.8)x oR.
    [Show full text]
  • Temperature Scales 2
    Straight Dope Staff Report: Why do we have so many temperature scales? [ Home Page | Message Boards | News | Archive | Books | Buy Stuff | FAQs, etc. ] A Staff Report by the Straight Dope Science Advisory Board Why do we have so many temperature scales? 28-Dec-2004 Dear Straight Dope: I have heard of five temperature measurements: Celsius (centigrade), Fahrenheit, Kelvin, Rankine, and Réaumur. How did so many scales arise? I know certain ones are goods for certain things (i.e., 0 Celsius is when water freezes, 0 Kelvin is absolute zero, etc.). But why are there so many, how did they arise, and can't you use one of them for all temperature purposes? --Josh G., Louisville, Kentucky Guest contributor hibernicus replies: You haven't heard the half of it. In addition to the Réaumur scale, which you mentioned, the roll-call of now-obsolete temperature scales includes the Newton, Rømer, Delisle, Leyden, Dalton, Wedgewood, Hales, Ducrest, Edinburgh and Florentine scales. In the 18th century, it was common to have up to four temperature scales (in one example, Newton, De Lisle, Réaumur and Fahrenheit) inscribed on the backing board of a thermometer. Today, the only scales in everyday use are the Celsius and Fahrenheit scales, and (mainly for scientists and engineers) the Kelvin and Rankine scales. Réaumur may be familiar to readers of 19th-century Russian and French novels; the others are largely forgotten. This story, of an unchecked proliferation of measurement units being pruned down to a few survivors, is not unique to temperature scales. I have a copy of an 18th century map of Switzerland which has seven distance scales, namely "Geometric or Italian miles," "Standard French Leagues," "Leagues of one hour's walk," "Standard German Leagues," "Short Swiss Leagues," "Standard Swiss Leagues," and "Long Swiss Leagues." I've seen as many as 13 scales on a single map, ranging from ancient Roman miles to Prussian wersts.
    [Show full text]
  • The Kelvin (Symbol: K) Is a Unit Increment of Temperature and Is One of the Seven SI Base Units
    The kelvin (symbol: K) is a unit increment of temperature and is one of the seven SI base units. The Kelvin scale is a thermodynamic (absolute) temperature scale referenced to absolute zero, the theoretical absence of all thermal energy. So by definition, the temperature of a substance at absolute zero is zero kelvin (0 K). The secondary reference point on the Kelvin scale is the triple point of water (0.01 degrees Celsius). The Kelvin scale is the difference between these two reference points, with the kelvin defined as one 273.16th of this scale. The Kelvin scale and the kelvin are named after the Belfast-born physicist and engineer William Thomson, 1st Baron Kelvin (1824ʹ1907), who wrote of the need for an "absolute thermometric scale". Unlike the degree Fahrenheit and degree Celsius, the kelvin is not referred to as a "degree", nor is it typeset with a degree symbol; that is, it is written K and not °K. The kelvin and the degree Celsius are often used together, as they have the same interval, and 0 kelvin is V273.15 degrees Celsius. reference: http://en.wikipedia.org/wiki/Kelvin In general, 'degrees' are found in units which are mainly arbitrary. Like, degrees Fahrenheit and Celsius, which are both arbitrary in the sense that their origin is chosen in an arbitrary way, and they are meant to be convenient instead of absolute. The same goes for angle degrees, since that also divides the circle into 360 degrees arbitrarily. When the units are absolute, or measured directly with respect to something else, one drops 'degrees' from the units.
    [Show full text]
  • Temperature Scales
    Just In Time Physics: Temperature Scales Heat and temperature are not the same thing. A match and a forest fire may well be at the same temperature, but the forest fire contains a lot more heat. Heat is a measure of how much energy is there, and heat is real. Heat is what bakes your bread, warms your house, and turns winter into summer. By contrast, temperature is just a number that tells you where the heat wants to go. Most people don’t think of temperature in these terms, but to a physicist, that’s exactly what temperature is. Heat always “flows from hotter to colder”, and when you say that, what you really mean is that heat always flows from spots with higher temperatures to spots with lower temperatures. A raging forest fire contains much more heat than a tiny white- hot incandescent light-bulb filament, but nonetheless, heat will flow away from the light bulb filament and towards the forest fire because the white-hot filament is at a higher temperature. Temperature is usually measured on one of three scales: the Fahrenheit, the Celsius (or centigrade), and the absolute (or Kelvin) scale. The only differences between these scales is where they place the zero value and how big the degrees are. The Fahrenheit scale is used more-or-less nowhere except in the United States. (The Cayman Islands and Belize, of all places, still use it, and it also shows up now and then in the United Kingdom and Canada.) This scale was created in 1724 by German physicist and instrument maker Daniel Fahrenheit, who decided to place his zero value at the coldest value he could easily generate, which was that of freezing salt water.
    [Show full text]