DOCSLIB.ORG

10. Design of Gravel and Low Standard Roads

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
10. Design of Gravel and Low Standard Roads 10. DESIGN OF GRAVEL AND LOW STANDARD ROADS 10.1 General Much of the information presented in this Section of the Pavement Design is based on the "Pavement and Materials Design Manual" prepared by the United Republic of Tanzania Ministry of Works 1999, and on relevant ERA and TRL publications. Available information has been modified to provide a simple procedure to design gravel wearing courses and low standard roads, which is appropriate to Ethiopian conditions. Gravel road pavements are generally utilized for roads where design traffic flow Annual Average Daily Traffic (AADT) is less than 200. This Section sets out the standards for pavement design, and specifies the materials which may be used for gravel roads. 10.2 Design Principles 10.2.1 STEPS TO BE CONSIDERED IN THE DESIGN PROCESS 1. Traffic (Baseline flow and forecast) 2. Material and geotechnical information (Field survey and material properties) 3. Subgrade (Classification, foundation for expansive soils and material strength) 4. Thickness design (Gravel wearing coarse thickness) 5. Materials design 10.2.2 ALL-WEATHER ACCESS An essential consideration in the design of gravel roads is to ensure all-weather access. This requirement places particular emphasis on the need for sufficient bearing capacity of the pavement structure and provision of drainage and sufficient earthworks in flood or problem soil areas (e.g. black cotton). 10.2.3 SURFACE PERFORMANCE The performance of the gravel surface mainly depends on material quality, the location of the road, and the volume of traffic using the road. Gravel roads passing through populated areas 211 in particular require materials that do not generate excessive dust in dry weather. Steep gradients place particular demands on gravel wearing course materials; this must not become slippery in wet weather or erode easily. Consideration should therefore be given to the type of gravel wearing course material to be used in particular locations such as towns or steep sections. Gravel loss rates of about 25-30mm thickness a year per 100 vehicles per day is expected, depending on rainfall and materials properties (particularly plasticity). Performance characteristics that will assist in identifying suitable material are shown in Figure 11-1. 10.2.4 MAINTENANCE The material requirements for the gravel wearing course include provision of a gravel surface that is effectively maintainable. Adherence to the limits on oversize particles in the material is of particular importance in this regard and will normally necessitate the use of crushing or screening equipment during material production activities. 10.3 Design Method The required gravel thickness shall be determined as follows: 1. Determine the minimum thickness necessary to avoid excessive compressive strain in the subgrade (D1). 2. Determine the extra thickness needed to compensate for the gravel loss under traffic during the period between regravelling operations (D2). 3. Determine the total gravel thickness required by adding the above two thicknesses (D1+ D2). 10.3.1 MINIMUM THICKNESS REQUIRED It is necessary to limit the compressive strain in the subgrade to prevent excessive permanent deformation at the surface of the road .Figure 3 gives the minimum gravel thickness required for each traffic category with the required thickness of improved subgrade materials for upper and lower subgrade layers. 212 10.3.2 GRAVEL LOSS According to TRL Laboratory Report 673, an estimate of the annual gravel loss is given by the following equation: GL = f T2 / ( T2 + 50) ( 4.2 + 0.092 T + 3.50 R2 + 1.88V) Where GL = the annual gravel loss measured in mm T = the total traffic volume in the first year in both directions, measured in thousands of vehicles R = the average annual rainfall measured in m V = the total (rise + fall) as a percentage of the length of the road f = 0.94 to 1.29 for lateritic gravels = 1.1 to 1.51 for quartizitic gravels = 0.7 to 0.96 for volcanic gravels (weathered lava or tuff) = 1.5 for coral gravels = 1.38 for sandstone gravels 10.3.3 TOTAL THICKNESS REQUIRED The wearing course of a new gravel road shall have a thickness D calculated from: D = D1 + N. GL Where D1 is the minimum thickness from Figure 11.3 N is the period between regravelling operations in years GL is the annual gravel loss Regravelling operations should be programmed to ensure that the actual gravel thickness never falls below the minimum thickness D1. 213 10.4 Pavement and Materials Depending on the CBRdesign of the sub grade, improved subgrade layers shall be constructed as required, on which the gravel wearing course is placed. 10.5 Crossfall and Drainage The crossfall of carriageway and shoulders for gravel roads shall be “ 4%” as indicated in ERA’s Geometric Design Manual - 2002. This is to ensure that potholes do not develop by rapidly removing surface water and to ensure that excessive crossfall does not cause erosion of the surface. Provision of drainage is extremely important for the performance of gravel roads. 10.6 Material Requirements 10.6.1 EXPERIENCE WITH LOCALMATERIALS Knowledge of past performance of locally occurring materials for gravel roads is essential. Material standards may be altered to take advantage of available gravel sources provided they have proved to give satisfactory performance under similar conditions. 10.6.2 MARGINALMATERIALS Figure 11-1 illustrates the performance characteristics to be expected of materials that do not meet the requirements for gravel wearing course. Refinements and amendments of the standard material specification may be necessary to overcome problem areas such as towns (dust nuisance) or steep hills (slipperiness). 10.6.3 IMPROVED SUBGRADE LAYER In General the use of improved subgrade layers has the following advantages: Provision of extra protection under heavy axle loads; Protection of underlying earthworks; Provides running surface for construction traffic; Assists compaction of upper pavement layers; 214 Provides homogenous subgrade strength; Acts as a drainage filter layer; More economical use of available materials. 10.6.4 SUBGRADE CBR All subgrade materials shall be brought to strength of at least a minimum CBR of 7% for minor gravel roads and at least a minimum CBR 25 % for major gravel roads. The different types of gravel roads are explained in Section 11.7. 10.6.5 TREATMENT OF EXPANSIVE FORMATIONS The following treatment operations should be applied on Expansive Formations for higher class roads of AADTdesign greater than 50: i) Removal of Expansive Soil a) Where the finished road level is designed to be less than 2 metres above ground level, remove the expansive soil to a minimum depth of 600 mm over the full width of the road, or b) Where the finished road level is designed to be greater than 2 metres above ground level, remove the expansive soil to a depth of 600 mm below the ground level under the unsurfaced area of the road structure, or c) Where the expansive soil does not exceed 1 meter in depth, remove it to its full depth. ii) Stockpile the excavated material on either side of the excavation for subsequent spreading on the fill slopes so as to produce as flat a slope as possible. iii) The excavation formed as directed in paragraph (i) should be backfilled with a plastic non-expansive soil of CBR value 3 - 4 or better, and compacted to a density of 95% modified AASHTO. iv) After the excavated material has been replaced with non-expansive material in 150mm lifts to 95% modified AASHTO density, bring the road to finished level in approved materials, with a side slope of 1:2, and ensure that pavement criteria 215 are complied with; the previously stockpiled expansive soil excavated as directed under (i) should then be spread over the slope. v) Do not construct side drains unless they are absolutely essential to stop ponding; where side drains are necessary, they should be as shallow as possible and located as far from the toe of the fill as possible. vi) Ideally, construction over expansive soil should be done when the in-situ moisture content is at its highest, i.e. at the end of rainy season The following treatment operations may be applied on Expansive Formations for light traffic class roads of AADTdesign less than 50: i) Remove 150mm of expansive topsoil and stockpile conveniently for subsequent use on shoulder slopes ii) Shape road bed and compact to 90% modified AASHTO iii) The excavation formed as directed in paragraph (i) should be backfilled with a plastic non-expansive soil of CBR value 3 - 4 or better, and compacted to a density of 95% modified AASHTO in each 150mm layer; the subgrade material may be plastic but non-expansive. 10.6.6 MATERIAL CHARACTERISTICS Soils used for improved subgrade layers shall be non-expansive, non-dispersive and free from any deleterious matter. They shall comply with the requirements shown inTable 10-1 216 10.7 Gravel Wearing Course 10.7.1 PERFORMANCE CHARACTERISTICS OF GRAVEL WEARING COURSE The materials for gravel wearing course should satisfy the following requirements that are often somewhat conflicting: a) They should have sufficient cohesion to prevent ravelling and corrugating (especially in dry conditions) b) The amount of fines (particularly plastic fines) should be limited to avoid a slippery surface under wet conditions. Figure 10-1 shows the effect of the Shrinkage Product (SP) and Grading Coefficient (GC) on the expected performance of gravel wearing course materials. Excessive oversize material in the gravel wearing course affects the riding quality in service and makes effective shaping of the surface difficult at the time of maintenance. For this reason the following two types of gravel wearing course material are recommended. Type 1 gravel wearing course which is one of the best material alternatives which shall be used on all roads which have AADTdesign greater than 50.
Load more

Recommended publications
  • PAVEMENT MANAGEMENT STUDY Templeton, MA
    PAVEMENT MANAGEMENT STUDY Templeton, MA Prepared by Stantec Date: September 2018 2 Stantec TABLE OF CONTENTS 1. INTRODUCTION 1 BACKGROUND 2 PAVEMENT MANAGEMENT CONCEPTS 3 STUDY APPROACH 5 2. METHODOLOGY 7 Pavement Management Software 8 The Pavement Condition Index (PCI) Defined 10 The Five Treatment Repair Bands 10 Priority Ranking and Future Projection 12 3. EXISTING CONDITIONS 15 Road Mileage and Current Pavement Condition Index (PCI) 16 Distribution of Pavement Conditions 21 Current Roadway Backlog 22 4. MODEL/PLANNING PROCESS 25 Budget Analysis 26 Scenario Findings 27 Zero Budget 28 Historical Budget (Worst-First) 29 Historical Budget (Pavement Management Strategy) 30 Equilibrium Funding Scenario 32 Progressive Funding Scenario 34 5. CONCLUSION 37 Recommended Plan of Action 38 Future Pavement Management 40 APPENDIX A. Templeton’s Public Roadway Backlog B. Repair Alternatives And Unit Costs C. Glossary D. Town-wide Pavement Conditions Map PAVEMENT MANAGEMENT STUDY Templeton, MA 3 TABLES 1. (PCI) Treatment Band Ranges 11 2. Zero Budget 28 3. Historical Budget (Worst First) 29 4. Historical Budget (Pavement Management Strategy) 31 5. Maintain PCI Funding Scenario 33 6. Progressive Funding Scenario 34 4 Stantec FIGURES 1. Pavement Deterioration Curve 4 2. PCI Distribution in Miles by Treatment Band 21 3. Dollar Backlog of Outstanding Repairs 22 4. Dollar Backlog Distribution vs. Dollar Budget Allocation 30 5. PCI Histogram of Network Conditions 32 6. Average PCI of Roadway Funding Scenarios 35 7. Dollar Backlog of Roadway Funding Scenarios 35 PAVEMENT MANAGEMENT STUDY Templeton, MA 5 SECTION NAME INTRODUCTION 1 BACKGROUND The Town of Templeton is located in Worcester County, Massachusetts which straddles Route 2 and comprises four main villages: Templeton Center, East Templeton, Baldwinville, and Otter River.
    [Show full text]
  • City Maintained Street Inventory
    City Maintained Streets Inventory DATE APPROX. AVG. STREET NAME ACCEPTED BEGINNING AT ENDING AT LENGTH WIDTH ACADEMYText0: ST Text6: HENDERSONVLText8: RD BROOKSHIREText10: ST T0.13 Tex20 ACADEMYText0: ST EXT Text6: FERNText8: ST MARIETTAText10: ST T0.06 Tex17 ACTONText0: WOODS RD Text6:9/1/1994 ACTONText8: CIRCLE DEADText10: END T0.24 Tex19 ADAMSText0: HILL RD Text6: BINGHAMText8: RD LOUISANAText10: AVE T0.17 Tex18 ADAMSText0: ST Text6: BARTLETText8: ST CHOCTAWText10: ST T0.16 Tex27 ADAMSWOODText0: RD Text6: CARIBOUText8: RD ENDText10: OF PAVEMENT T0.16 Tex26 AIKENText0: ALLEY Text6: TACOMAText8: CIR WESTOVERText10: ALLEY T0.05 Tex12 ALABAMAText0: AVE Text6: HANOVERText8: ST SWANNANOAText10: AVE T0.33 Tex24 ALBEMARLEText0: PL Text6: BAIRDText8: ST ENDText10: MAINT T0.09 Tex18 ALBEMARLEText0: RD Text6: BAIRDText8: ST ORCHARDText10: RD T0.2 Tex20 ALCLAREText0: CT Text6: ENDText8: C&G ENDText10: PVMT T0.06 Tex22 ALCLAREText0: DR Text6: CHANGEText8: IN WIDTH ENDText10: C&G T0.17 Tex18 ALCLAREText0: DR Text6: SAREVAText8: AVE CHANGEText10: IN WIDTH T0.18 Tex26 ALEXANDERText0: DR Text6: ARDIMONText8: PK WINDSWEPTText10: DR T0.37 Tex24 ALEXANDERText0: DR Text6: MARTINText8: LUTHER KING WEAVERText10: ST T0.02 Tex33 ALEXANDERText0: DR Text6: CURVEText8: ST ARDMIONText10: PK T0.42 Tex24 ALLENText0: AVE 0Text6:/18/1988 U.S.Text8: 25 ENDText10: PAV'T T0.23 Tex19 ALLENText0: ST Text6: STATEText8: ST HAYWOODText10: RD T0.19 Tex23 ALLESARNText0: RD Text6: ELKWOODText8: AVE ENDText10: PVMT T0.11 Tex22 ALLIANCEText0: CT 4Text6:/14/2009 RIDGEFIELDText8:
    [Show full text]
  • Pavements and Surface Materials
    N O N P O I N T E D U C A T I O N F O R M U N I C I P A L O F F I C I A L S TECHNICAL PAPER NUMBER 8 Pavements and Surface Materials By Jim Gibbons, UConn Extension Land Use Educator, 1999 Introduction Traffic Class Type of Road Pavements are composite materials that bear the weight of 1 Parking Lots, Driveways, Rural pedestrian and vehicular loads. Pavement thickness, width and Roads type should vary based on the intended function of the paved area. 2 Residential Streets 3 Collector Roads Pavement Thickness 4 Arterial roads 5 Freeways, Expressways, Interstates Pavement thickness is determined by four factors: environment, traffic, base characteristics and the pavement material used. Based on the above classes, pavement thickness ranges from 3" for a Class 1 parking lot, to 10" or more for Class 5 freeways. Environmental factors such as moisture and temperature significantly affect pavement. For example, as soil moisture Sub grade strength has the greatest effect in determining increases the load bearing capacity of the soil decreases and the pavement thickness. As a general rule, weaker sub grades require soil can heave and swell. Temperature also effects the load thicker asphalt layers to adequately bear different loads associated bearing capacity of pavements. When the moisture in pavement with different uses. The bearing capacity and permeability of the freezes and thaws, it creates stress leading to pavement heaving. sub grade influences total pavement thickness. There are actually The detrimental effects of moisture can be reduced or eliminated two or three separate layers or courses below the paved wearing by: keeping it from entering the pavement base, removing it before surface including: the sub grade, sub base and base.
    [Show full text]
  • Inventory and Condition Assessment of Road Surfaces
    INVENTORY AND CONDITION ASSESSMENT OF ROAD SURFACES _____________________________ Town of Boulder Junction August 2017 Table of Contents 1. Introduction 2. Road Condition Survey 2.1 Inventory of Town Roads 2.2 Identifying Deficiencies 2.3 Condition Assessment 3. Selection of Repair Alternatives 3.1 Baseline Improvements 3.2 Repair Alternatives 4. Prioritizing the Town of Boulder Junction’s Road Repair Needs 4.1 Priority Setting Factors 4.2 Estimated Costs 4.3 Priorities of Roads Appendices Appendix A – Chip Seal Maintenance Prioritized by Year (1-5) Appendix B – Estimated Costs by Road Appendix C – Improvements (All Roads) Prioritized by Year (1-15) Appendix D – Improvements (Excluding Gravel Road Upgrades) Prioritized by Year (1-15) Appendix E – Improvements (Excluding Gravel Road Upgrades) Prioritized by Year (1-3) TOWN & COUNTRY ENGINEERING, INC. Madison Rhinelander Kenosha 2912 Marketplace Drive, Suite 103 • Madison, WI 53719 • (608) 273-3350 • [email protected] 1. Introduction Town & Country Engineering, Inc. has conducted a windshield level road surface condition survey of the Town of Boulder Junction’s 93 miles of roadway during six separate site visits. The survey was conducted along with the Town Board Chairman and a Road Improvement Committee member who provided information on each road based on historical observations concerning drainage, plowing, maintenance and other miscellaneous issues specific to each roadway. The purpose of the survey was to note observable deficiencies and areas of potential improvement, including structural and road bed improvements, safety related changes and drainage. Deficiencies vary from general drainage issues (lack of ditching) to specific areas of interest including particularly acute issues that may be able to be corrected with focused effort.
    [Show full text]
  • Gravel Roads Maintenance & Frontrunner Training Workshop
    A Ditch In Time Gravel Roads Maintenance Workshop 1 So you think you’ve got a wicked driveway 2 1600’ driveway with four switchbacks and 175’ of elevation change (11% grade) 3 Rockhouse Development, Conway 4 5 6 Swift River (left) through National Forest into Saco River that drains the MWV Valley’s developments 7 The best material starts as solid rock that is drilled & blasted… 8 Then crushed into smaller pieces and screened to produce specific size aggregate 9 How strong should it be? One big truck = 10,000 cars! 10 11 The road surface… • Lots of small aggregate (stones) to provide strength with a shape that will lock stones together to support wheels • Sufficient “fines,” the binder that will lock the stones together, to keep the stones from moving around 12 • The stone: hard and uniform in size and more angular than that made just from screening bank run gravel 13 • A proper combination of correctly sized broken rock, sand and silt/clay soil materials will produce a road surface that hardens into a strong and stable crust that forms a reasonably impervious “roof” to our road • An improper balance- a surface that is loose, soft & greasy when wet, or excessively dusty when dry (see samples) 14 One way to judge whether gravel will pack or not… 15 Here’s another way… 16 Or: The VeryFine test The sticky palm test As shown in the Camp Roads manual 17 • “Dirty” gravel packs but does not drain • “Clean” gravel drains but does not pack 18 Other road surfacing materials: • Rotten Rock- traditional surfacing material in the Mt Washington Valley
    [Show full text]
  • Cover Technical Guides Convert.Indd
    If there are sharp curves in the road where vehicles can maintain a high speed, invert In sharp curved the the camber of the road (see also fi gure 43). This will reduce the risks of slipping camber of on the vehicles. Inverting the camber is gradually built up over a 20m section before entering outer side needs to into the curve. be inverted Figure 45: Example of inverting the camber in a sharp curve 7.4 Graveling In the past graveling of roads was considered an effective and cost-effective option Gravel surfaces for surfacing low-volume rural roads. Recent research however shows that gravel have many roads have serious limitations in many situations. Very often gravel surfaces are not limitations appropriate, affordable or sustainable for rural roads. There are for example serious problems related to the maintenance and sustainability of gravel surfaces (or ordinary earth roads). Although the initial construction costs of gravel roads are low, the maintenance costs are very high. The suitability of graveling roads depends on a range of factors. These include for example the road gradient, rainfall, material quality, haul distance and maintenance regime. Gravel should NOT be used if any of the following conditions, or a combination of them applies: Gravel quality is poor; Situations Compaction & thickness cannot be assured ; where gravel is not suitable as Haul distances are longer than 10km; surface option Rainfall is very high – Gravel loss is related to rainfall; There are dry season dust problems; Technical Guidelines for Supervisors Technical Traffi c levels are high, i.e. more than 200 vehicle equivalents per day; 49 Road gradients are more than 6% (with < 1,000mm rain per year) or more than 4% (with 1,000 – 2,000mm rain per year); If rainfall is more than 2,000mm/year; Adequate maintenance cannot be provided; Sub-grade is weak or soaked; Gravel deposits are limited or environmentally sensitive.
    [Show full text]
  • Road Standards
    P O L K C O U N T Y D E P A R T M E N T O F P U B L I C W O R K S R O A D S T A N D A R D S The Polk County Board of Commissioners Adopted These Standards on July 22, 1998 These standards prepared by and under the auspices of the staff of the Public Works Department TABLE OF CONTENTS Section Page I. Introduction................................................................................................................1 II. Application.................................................................................................................1 III. Definitions..................................................................................................................1 IV. Functional Classification ...........................................................................................4 V. Project Types.............................................................................................................5 VI. Access To A County Road ........................................................................................6 VII. Public Use Roads.......................................................................................................10 VIII. Private Roads.............................................................................................................11 IX. Use Of County Right-of-Way By Others .................................................................13 X. Transportation Impact Analysis ................................................................................14 XI. Roadway Design
    [Show full text]
  • St. Louis County Traffic Sign Policy
    St. Louis County Traffic Sign Policy March 2014 St. Louis County Public Works Department Author: Victor Lund, PE Traffic Engineer St. Louis County [email protected] St. Louis County Technical Advisory Committee: James Foldesi, Public Works Director/Highway Engineer Brian Boder, Assistant County Engineer Kimberly Maki, Attorney Roland Hanson, Sign Supervisor Steve Anderson, Sign Supervisor Prepared for: St. Louis County Public Works Department 4787 Midway Road Duluth, MN 55811 218-625-3830 www.stlouiscountymn.gov TABLE OF CONTENTS 1. PURPOSE AND BACKGROUND ...................................................................................... 1 2. POLICY STATEMENT ....................................................................................................... 1 3. SIGN RETROREFLECTIVITY MANAGEMENT METHOD ................................................. 1 4. TRAFFIC SIGN MANAGEMENT ....................................................................................... 2 5. TRAFFIC SIGN STANDARDS AND GUIDANCE .............................................................. 2 5.1. SIGN SHEETING ............................................................................................................................. 2 5.2. SIGN POSTS .................................................................................................................................. 2 5.3. REGULATORY SIGNS ...................................................................................................................... 2 5.4. WARNING SIGNS
    [Show full text]
  • Camp Road Maintenance Manual
    GRAVEL ROAD MAINTENANCE MANUAL A Guide for Landowners on Camp and Other Gravel Roads Kennebec County Maine Department of Soil and Water Environmental Protection Bureaus of Land Conservation District Resources and Water Quality April 2016 For the purposes of this manual, the terms “gravel road” and “camp road” are used interchangeably and are used to describe private and public roads that are typically narrow and unpaved. - TABLE OF CONTENTS - ACKNOWLEDGEMENTS I INTRODUCTION 1 A Little History on Camp Roads 1 Some Questions and Answers 3 TROUBLESHOOTING GUIDE 7 Road Surface Problems 7 Culvert Problems 9 Ditch Problems 10 UNDERSTANDING THE BASICS 11 Soil Erosion 11 Factors Linked to Erosion 12 Water and Your Road 13 Surface Water 14 Groundwater 14 Erosion Control Principles 15 Work with Nature 17 Where to Drain to: Vegetated Buffers 17 Types of Buffers 18 How to Have an Effective Buffer 18 Buffers: Cost-Effective, Low Maintenance, and Good for the Lake 19 CAMP ROAD MAINTENANCE 20 Road Surface 20 Road Level 20 Road Materials 21 Road Material Composition 22 Alternative Road Surfacing Materials 24 Geotextiles as Road Base 24 Reclaimed Pavement/Recycled Asphalt (Reclaim) 26 Pavement 27 Other Alternative Surface Materials 27 Grading 28 Crowning and Super-Elevating 30 Alternative Equipment 33 Steel Tine Rake 33 Frontrunner Device 34 Dust Control 35 Winter Maintenance 37 Road Drainage 39 Ditches 39 Ditch Shape 40 Ditch Size and Depth 42 Ditch Erosion and Stabilization 43 Erosion in Ditches 43 Seeding and Mulching 44 Erosion Control Mix 46 Erosion
    [Show full text]
  • Road Infrastructure
    prosperity through mobility Part 2 REPORT OF THE HEAD OF TRANSPORT SECTION3: PROGRAMME 2: ROAD INFRASTRUCTURE Sub-programme 2.1 Programme Support Office Public Private Partnership (PPP) for Sourcing Engineering Plant Consequent to difficulties experienced by Vukuzakhe Contractors when hiring engineering plant, the Department identified a need to establish a Public Private Partnership for the hiring of engineering plants by Vukuzakhe Contractors at reasonable rates. To mention one problem, the exorbitant plant hire rates charged to Vukuzakhe Contractors increased the cost of road construction. As a result, strategies to address the situation and provide support to the emergence of Broad Based Black Economic Empowerment (BBBEE) Construction Companies who do not have ready access to engineering plant,s were developed. A feasibility study of a PPP was conducted and a document submitted to Provincial Treasury for approval. The second phase will be the roll out during the 2005/06 financial year, once approval has been obtained. Technology Transfer Centre The Departments Technology Training centre was actively involved during the 2004/05 financial year in re-alignment of the organisational structure in response to changes in customer training needs. The centre also relocated from the Pietermaritzburg Region to new offices at Head Office. The renovations at the Technology Transfer Centre which were undertaken during the 2004/05 financial year created a conducive environment that provides standard facilities including :- a modern materials testing laboratory; a mechanical workshop for training mechanical apprentices; four (4) modern equipped training rooms; a refurbished theatre; two (2) computer training rooms equipped with approximately 30 desk tops; a documentation centre; and a modern boardroom.
    [Show full text]
  • Dirt and Gravel Road BMP Guide
    Dirt and Gravel Road Best Management Practice Guide Landowner’s Handbook to Building and Maintaining Private Roadways Published by the Culpeper Soil and Water Conservation District with funding from the Chesapeake Bay Restoration Fund. January 2019 Table of Contents Introduction………………………………………………………………1 Site Assessment…………………………………………………………2 Design and Construction Considerations…………………3 Road Assessment………………………………………………………4 Common Problems……………………………………………………5 Troubleshooting………………………………………………………6 Maintenance……………………………………………………………8 Maintenance Schedule……………………………………………9 Inspection Checklist……………………………………………….10 Definitions………………………………………………………………11 References………………………………………………………………12 Acknowledgements………………………………………………..12 Section 2: Practice Specifications………………………….13-26 Dirt and Gravel Road BMP Guide Introduction There are close to 400 miles of dirt and gravel roads in the Culpeper District. Dirt and gravel roads are low-volume roads that have relatively low use and provide service to residences and agricultural, logging and recreational areas. Most dirt and gravel roads are privately maintained and serve individual lots or small subdivisions. Maintaining and improving these roads can be a major responsibility for landowners. Over time many roads and driveways Figure 1 deteriorate for a variety of reasons: poor construction, improper maintenance, excessive weather events, heavy traffic loads, and others. In addition to the high and frequent repair costs, many of these roads and roadside ditches drain directly into our waterways. The transport of both sediment and gravel into stream channels has a destructive impact to the stream ecosystem resulting in the smothering of aquatic habitat and reduction of the channel’s capacity to carry water. Sedimentation of the channel causes increased frequency of flooding and streambank erosion. Competent construction and maintenance of dirt and gravel roads can save the landowner money and better protect local waterways.
    [Show full text]
  • Gravel Roads Construction and Maintenance Guide Table of Contents Subject Page
    Errata ­ Replaces page 137 Reconstruction Using a Detour When the reconstruction and resulting berm are significant, the work space takes all or most of the road surface, leaving no room for traffic to negotiate past the work activities. An agency may need to reconstruct the unpaved roadway by correcting the drainage and/or adding surface materials. With this type of work, additional equipment may be used and a large amount of material may create a large berm (12 inches or more across). This will present significant hazards for the traveling public. To improve safety for mo­ torists and workers, a detour may be the best TTC. Not all road users will be familiar with the local road system and some may be confused by the road closure, so signing should be used to assist users negotiating the detour. Reconstruction work space. (Source: Greg Vavra, SDLTAP). Notes: 1. Not all local agencies use route makers for their system. MUTCD Section 6F.59 states “A Street Name sign should be placed above, or the street name should be incorporated into, a DETOUR (M4­9) sign to indicate the name of the street being detoured.” 2. With an increase in traffic at the intersections where the detour begins and ends, a review of the usage of the STOP and YIELD signs should be completed. 3. Flashing warning lights and/or flags may be used to call attention to advance warning signs. 4. Flashing warning lights may be used on the Type 3 Barricades, which should be installed at the point where the road is closed.
    [Show full text]