Contacts Lantronix, Inc. Corporate Headquarters 167 Technology Drive Irvine, CA 92618, USA Toll Free: 800-526-8766 Phone: 949-453-3990 Fax: 949-453-3995 Technical Support Online: www.lantronix.com/support Sales Offices For a current list of our domestic and international sales offices, go to the Lantronix web site at www.lantronix.com/about/contact.
Disclaimer The information in this guide may change without notice. The manufacturer assumes no responsibility for any errors that may appear in this guide. For the latest revision of this product document, please check our online documentation at www.lantronix.com/support/documentation.
September 2008 B Technical updates throughout, corresponding to release 1.1.0.0 R6.
May 2010 C Updated for firmware release 5.1.0.0 R10.
November 2013 D Updated for firmware release 5.2.0.4.
MatchPort® AR Embedded Device Server Command Reference 2 Table of Contents
List of Figures ______4 List of Tables ______5
1: About This Guide 6 Chapter Summaries ______6 Conventions ______6 Additional Documentation ______7
2: Overview 8 XML Architecture and Device Control ______8 Command Line Interface ______8
3: Command Line Interface 9 Configuration Using Telnet ______9 Configuration Using Serial Ports ______9 Serial Command Mode ______9 Serial Recovery ______9 Navigating the CLI Hierarchy ______10 Using Keyboard Shortcuts and CLI ______11 Understanding the CLI Level Hierarchy ______11
4: Configuration Using XML 14 XML Configuration Record Document Type Definition ______14 Quick Tour of XML Syntax ______15 Declaration ______15 Element Start and End Tags ______15 Element Attributes ______15 Record, Group, Item, and Value Tags ______16 Importing and Exporting an XML Configuration File ______17 Best Practices ______18 Importing ______18 Exporting ______19 Passwords in the XML File ______19 XML Configuration Groups ______20 XML Status Record Groups and Items ______32
5: Commands and Levels 43
MatchPort® AR Embedded Device Server Command Reference 3 List of Figures
Figure 3-1 CLI Level Hierarchy ______12 Figure 3-2 Login Level Commands______13 Figure 3-3 Enable Level Commands______13 Figure 4-1 DTD for XCRs ______14 Figure 4-2 XML Example ______15 Figure 4-3 XML Group Example ______16 Figure 4-4 XML Example of Multiple Named Values ______16 Figure 4-5 XML Example of Multiple Items ______17 Figure 4-6 XML Example with Multiple Groups ______17 Figure 4-7 XML Example of Supplying Passwords______20
MatchPort® AR Embedded Device Server Command Reference 4 List of Tables
Table 4-8 XCR Groups ______20 Table 4-9 XSR Groups and Items______32 Table 5-1 Commands and Levels ______45
MatchPort® AR Embedded Device Server Command Reference 5 1: About This Guide
This guide describes how to configure the Lantronix® MatchPort® AR embedded device server using the Command Line Interface (CLI) and/or Extensible Markup Language (XML). CLI provides an interactive mode for accessing the device configuration and management interface. It is most suited for system and network administrators comfortable with using similar interfaces on Enterprise IT and Networking products. It is also helpful as quick tool for access via the product's serial ports or console/management ports. XML provides an extensible mode for software developers interfacing with the device and system integrators performing batch provisioning/updates.
Chapter Summaries
This table lists and summarizes each chapter and appendix.
Chapter Summary
Chapter 2: Overview Gives an overview of CLI and XML.
Chapter 3: Command Line Interface Lists commands and describes how to use CLI to configure the MatchPort AR embedded device server.
Chapter 4: Configuration Using XML Lists XCR groups and items and describes how to use XCRs to configure the MatchPort AR unit.
Chapter 5: Commands and Levels Provides an index of the CLI Command Hierarchy with hyperlinks to the corresponding command details.
Conventions The table below lists and describes the conventions used in this book.
Convention Description
Bold text Default parameters.
Italic text Required values for parameters
Brackets [ ] Optional parameters.
Angle Brackets < > Possible values for parameters.
Pipe | Choice of parameters.
Warning Warning: Means that you are in a situation that could cause equipment damage or bodily injury. Before you work on any equipment, you must be aware of the hazards involved with electrical circuitry and familiar with standard practices for preventing accidents.
Note Note: Means take notice. Notes contain helpful suggestions, information, or references to material not covered in the publication.
MatchPort® AR Embedded Device Server Command Reference 6 1: About This Guide
Convention Description
Caution Caution: Means you might do something that could result in faulty equipment operation, or loss of data.
Screen Font CLI terminal sessions and examples of CLI input. (Courier New)
Additional Documentation Visit the Lantronix web site at www.lantronix.com/support/documentation for the latest documentation and the following additional documentation.
Document Description
MatchPort AR Embedded Device Describes how to configure and use the MatchPort AR embedded Server User Guide device server.
MatchPort AR Embedded Device Contains information about the MatchPort AR hardware, the Server Integration Guide MatchPort AR demonstration board, and integrating into your product.
MatchPort AR Embedded Device Describes how to get the MatchPort AR demonstration board up Server Getting Started Guide and running.
DeviceInstaller Online Help Instructions for using the Lantronix Windows-based utility to locate the MatchPort AR embedded device server and to view its current settings.
Secure Com Port Redirector Instructions for using the Lantronix Windows-based utility to create User Guide secure virtual com ports.
Com Port Redirector Instructions for using the Lantronix Windows-based utility to Quick Start and Online Help create virtual com ports.
MatchPort® AR Embedded Device Server Command Reference 7 2: Overview
Evolution OS® software is the Lantronix® cutting-edge operating system that supports three convenient configuration methods: Web Manager, Command Line Interface (CLI), and Extensible Markup Language (XML). For more information about the Web Manager, see the MatchPort AR Embedded Device Server User Guide at the Lantronix website.
XML Architecture and Device Control XML is a fundamental building block for the future growth of Machine-to-Machine (M2M) networks. Evolution OS supports XML configuration records that make configuring the device server easy for users and administrators. XML configuration records are easy to edit with a standard text editor or an XML editor. For a brief overview of XML, see Chapter 4: Configuration Using XML . It provides rules on basic XML syntax, a guide to the specific XML tags used, and a guide to using XML configuration records.
Command Line Interface Making the edge-to-enterprise vision a reality, Evolution OS uses industry-standard tools for configuration, communication, and control. For example, the Evolution OS uses a command line interface (CLI) whose syntax is very similar to that used by data center equipment such as routers and hubs. For details of the CLI, see Chapter 5: Commands and Levels. It provides an index of the CLI Command Hierarchy with links to the corresponding command details. The CLI provides commands for configuring, monitoring, and controlling the device server.
MatchPort® AR Embedded Device Server Command Reference 8 3: Command Line Interface
This chapter describes accessing the MatchPort AR embedded device server by using Telnet, SSH, or serial ports to configure the unit, navigating the Command Line Interface (CLI), typing keyboard shortcuts, and moving between the levels. It contains the following sections:
Configuration Using Telnet
Configuration Using Serial Ports
Navigating the CLI Hierarchy
Using Keyboard Shortcuts and CLI
Understanding the CLI Level Hierarchy Refer to Chapter 5: Commands and Levels for a complete list of levels, commands, and descriptions.
Configuration Using Telnet To access and configure the device server by using a Telnet session over the network, you must first establish a Telnet connection. You can also establish a Telnet connection by clicking the Telnet Configuration tab in DeviceInstaller application. See the DeviceInstaller Online Help for more information, available on our website www.lantronix.com/support/downloads. To access the MatchPort AR embedded device server by using Telnet, perform the following steps. 1. Click Start > Run. The Run dialog box displays. 2. Type cmd in the dialog box and press OK. 3. Type telnet x.x.x.x (x.x.x.x is the IP address). The MatchPort AR unit is online when the command prompt (>) displays. You are at the root level of the CLI.
Note: Depending on the level of security, a password may be required.
Configuration Using Serial Ports
Serial Command Mode The serial port can be configured to operate in command mode permanently or to be triggered under specified conditions. See the line Level command description for more information.
Serial Recovery In this mode, the normal boot process is interrupted, allowing recovery from unknown or incorrect configuration settings. While the back door is active, the CLI prompt is changed to “>>” (instead of “>”) and the Web Manager is inaccessible. These serve as an important indication that the device boot processes has been temporarily halted. To complete the boot process, terminate the serial CLI session (with the exit command).
MatchPort® AR Embedded Device Server Command Reference 9 3: Command Line Interface
To configure the Lantronix device server locally using a serial port, connect a terminal or a PC running a terminal emulation program to one of the device server's serial ports. Configure the terminal for 9600 baud, 8-bit, no parity, 1 stop bit, and no flow control. 1. Power off the device. 2. Press and hold down the exclamation point (!) key. 3. Power on the device. After about ten seconds, the exclamation point will display on the terminal or PC screen. 4. Type xyz within 5 seconds to display the CLI prompt.
Navigating the CLI Hierarchy The CLI is organized into a hierarchy of levels. Each level has a group of commands for a specific purpose. For example, to configure a setting for the FTP server, one would navigate to the FTP level, which is under the configuration level.
To move to a different level—Enter the name of the level from within its parent level. For example, to enter the tunnel level, type tunnel at the enable prompt. This displays: tunnel #.
To exit and return to one level higher—Type exit and press the Enter key. Typing exit at the login level or the enable level will close the CLI session. If Line — Command Mode is specified as Always, a new session starts immediately.
To view the current configuration at any level—Type show.
To view the list of commands available at the current level—Type the question mark "?". Items within < > (e.g. ) are required parameters.
To view the available commands and explanations—Type the asterisk ( *).
To view the list of commands available for a partial command—Type the partial command followed by the question mark "?". For example: #echo? displays a list of all echo commands at the tunnel level.
To view available commands and their explanations for a partial command—Type the partial command followed by the asterisk ( *). For example: #echo* displays a list of all echo commands and descriptions at the tunnel level.
To view the last 20 commands entered at the CLI—Type show history.
MatchPort® AR Embedded Device Server Command Reference 10 3: Command Line Interface
Using Keyboard Shortcuts and CLI One useful shortcut built into Evolution OS operating system is that the complete text of a command does not have to be entered to issue a command. Typing just enough characters to uniquely identify a command, then hitting enter, can be used as a short cut for a command. For example, at the enable level, "sh" can be used for the "show" command. Tab Completion is also available. Typing the first few characters of a command, then hitting the key displays the first command that begins with those characters. Hitting the key again displays the next command that begins with the original characters typed. You can press to execute the command or you can backspace to edit any parameters. The following key combinations are allowed when configuring the device server using the CLI:
Ctrl + a: place cursor at the beginning of a line
Ctrl + b: backspace one character
Ctrl + d: delete one character
Ctrl + e: place cursor at the end of the line
Ctrl + f: move cursor forward one character
Ctrl + k: delete from the current position to the end of the line
Ctrl + l: redraw the command line
Ctrl + n: display the next line in the history
Ctrl + p: display the previous line in the history
Ctrl + u: delete entire line and place cursor at start of prompt
Understanding the CLI Level Hierarchy The CLI hierarchy is a series of levels. Arranging commands in a hierarchy of levels provides a way to organize and group similar commands, provide different levels of security, and reduce the complexity and number commands and options presented to a user at one time. When you start a command line session, you begin at the login level. This level can be password protected and provides access to high level status, a few diagnostic commands, and the enable level. Further device information and configuration are accessed via the enable level. The enable level can also be password protected and is the gateway to full configuration and management of the device server. There are commands for gathering and effecting all elements of device status and configuration, as well as commands that take you to additional levels. For instance, tunnel specific status and configuration is found under the "tunnel" level, and network specific status and configuration commands are found under the "configuration" level. An overview of the levels in the MatchPort AR embedded device server is presented in Figure 3-1.
MatchPort® AR Embedded Device Server Command Reference 11 3: Command Line Interface
Figure 3-1 CLI Level Hierarchy
(login) enable configure arp
cpm cli
ssh device
telnet dns
email diagnostics log cp ftp filesystem host line http
Commands at the login level, shown in Figure 3-2, do not affect current configuration settings and are not displayed initially. If you type , you will see the login sub-commands. These commands provide diagnostic and status information only.
MatchPort® AR Embedded Device Server Command Reference 12 3: Command Line Interface
Figure 3-2 Login Level Commands
>? clrscrn enable exit ping ping ping show show history show matchport_ar trace route
>
To configure the MatchPort AR, you must be in the enable level and any of its sub-levels. Figure 3-3 shows the enable level commands.
Figure 3-3 Enable Level Commands
>enable (enable)#? auto show interfaces auto show processes clear interfaces counters clrscrn configure connect connect line cpm device disable dns email exit filesystem kill ssh kill telnet line lpd no clear interfaces counters ping ping ping ppp reload reload factory defaults show show history show interfaces show ip sockets show matchport_ar show processes show sessions ssh ssh ssh ssl telnet telnet trace route tunnel write xml
(enable)#
See the Chapter 5: Commands and Levels at the end of this document for a complete list of levels, commands, and descriptions.
MatchPort® AR Embedded Device Server Command Reference 13 4: Configuration Using XML
The MatchPort AR Pro embedded device server provides an Extensible Markup Language (XML) interface that you can use to configure device server devices. Every configuration setting that can be issued from the device server Web Manager and CLI can be specified using XML. The device server can import and export configuration settings as an XML document known as an XML Configuration Record (XCR). An XCR can be imported or exported via the CLI, a Web browser, FTP, or the device server filesystem. An XCR can contain many configuration settings or just a few. For example, it might change all of the configurable parameters for a device server, or it may only change the baud rate for a single serial line. Using XCRs is a straightforward and flexible way to manage the configuration of multiple device server devices.
XML Configuration Record Document Type Definition An XML document type definition (DTD) is a description of the structure and content of an XML document. It verifies that a document is valid. XCRs are exported using the DTD shown in Figure 4-1.
Figure 4-1 DTD for XCRs
]>
The device server DTD rules state the following:
The XML document element is a element. This is the root element.
A must have one or more elements and can have a version attribute.
A must have one or more elements and can have name and instance attributes.
A element must have one or more elements and can have a name attribute.
A element can have only data and can have a name attribute.
The name attribute identifies a group, item, or value. It is always a quoted string.
The instance attribute identifies the specific option, like the serial port number. The “instance” attribute is always a quoted string.
MatchPort® AR Embedded Device Server Command Reference 14 4: Configuration Using XML
Notes:
The name for each (specified with the name attribute) is the group name listed in the Web Manager XCR groups or with the “xcr list” CLI command. See the MatchPort AR Embedded Device Server User Guide for more information about the Web Manager XCR groups.
An empty or missing element in each present clears the setting to its default.
Quick Tour of XML Syntax
Declaration The first line, , is called the XML declaration. It is required and indicates the XML version in use (normally version 1.0). The remainder of the file consists of nested XML elements, some of which have attributes and content.
Element Start and End Tags An element typically consists of two tags: start tag and an end tag that surrounds text and other elements (element content). The start tag consists of a name surrounded by angle brackets, for example . The end tag consists of the same name surrounded by angle brackets, but with a forward slash preceding the name, for example . The element content can also contain other “child” elements.
Element Attributes The XML element attributes that are name-value pairs included in the start tag after the element name. The values must always be quoted, using single or double quotes. Each attribute name should appear only once in an element. Figure 4-2 shows an XML example which consists of a declaration (first line), nested elements with attributes and content.
Figure 4-2 XML Example
disable
The Evolution OS operating system uses the attributes in the following subsections to label the group configuration settings.
MatchPort® AR Embedded Device Server Command Reference 15 4: Configuration Using XML
Record, Group, Item, and Value Tags A is a logical grouping of configuration parameters and must contain one or more elements. It must have a name attribute and may have an instance attribute. A is a specific grouping of configuration parameters relevant to its parent group. An item takes the name attribute and must contain one or more value elements. For example, the line group might have parameters such as baud rate, data bits, and parity. A value may specify the value of a configuration parameter. It may contain the name attribute. In this example, a value of 9600 might be specified for baud rate; 7 may be specified for data bits, and even may be specified for parity. A name attribute identifies the group, item, or value. It is always quoted (as are all XML attributes). For example, a group that contains serial port parameters has the name “line”. An instance attribute identifies which of several instances is being addressed. It is always quoted. For example, the serial port name (in the line configgroup) has the instance “1” to indicate serial port 1 or “2” to specify serial port 2. The following figures show examples of XML configuration records and the use of the , , , and XML elements.
Figure 4-3 XML Group Example
disable
Figure 4-4 XML Example of Multiple Named Values
MatchPort® AR Embedded Device Server Command Reference 16 4: Configuration Using XML
Importing and Exporting an XML Configuration File An XCR can be imported or exported using the following methods:
Filesystem—XCRs can be saved to the device server file system and imported or accessed as needed. See Best Practices or the Filesystem Browser section in the MatchPort AR Embedded Device Server User Guide.
CLI—XCRs can be imported (captured) or exported (dumped) directly to a Telnet, SSH, or serial line CLI session. Capturing an XCR can be started by pasting a valid XCR directly into the CLI prompt. Evolution OS immediately processes the configuration record, changing any
MatchPort® AR Embedded Device Server Command Reference 17 4: Configuration Using XML
settings specified. This can be done on any level, including the root. Special tags in the XML allow for providing root and enable level passwords so that this can also be done at the password prompt.
Web browser—Web Manager can be used to import and export an XCR to the device server file system. It can also be used to import an XCR from an external source such as your local hard drive.
FTP—The device server FTP server can export and import XCRs when an FTP get or put command on the filename matchport_ar is requested. On export (FTP get of matchport_ar), the FTP server obtains the current XCR from Evolution OS and sends it as a file. On import (FTP put of matchport_ar), the FTP server processes the file by sending it directly to the XML engine. In both cases the device server filesystem is not accessed. The file matchport_ar is not read from or written to the file system. See FTP in the MatchPort AR Embedded Device Server User Guide.
TFTP—TFTP supports XCR importing. Due to limited security capabilities of TFTP, the option is disabled by default.
Best Practices You can import or export an entire XCR, or just a portion of it, by specifying the group name and/or group instances. In the examples below, import and export operations are performed from the CLI on the local filesystem and require a XCR on the local filesystem. The Web Manager provides the same functionality.
Caution: Using Microsoft Word to edit and save an XCR will change the format of the file and make it incompatible with Evolution OS. This is true even if the file is saved as Plain Text (.txt) or an XML Document (.xml). Notepad, a third party text editor, or a specialized XML editor should be used instead.
Importing The following syntax can be used to import configurations from a file: xcr import xcr import The first line imports all groups specified in the XML config record named in . Any filename is valid, and the file name and extension are not important.
Caution: The filename matchport_ar.xcr is not acceptable, because performing a FTP get on that name produces the current configuration and does not perform an FTP from the filesystem. Also, the filename matchport_ar.xsr is not acceptable, because performing an FTP get on that name produces the current status and does not get anything from the filesystem. In the second line:
Instance follows group with a colon (see the third example on the next page).
Multiple groups are separated with a comma.
Any white space requires the list of groups to be quoted.
MatchPort® AR Embedded Device Server Command Reference 18 4: Configuration Using XML
Only the named groups get imported, even if the XCR contains additional XCR groups. The following syntax can be used to export configurations to a file on the device server’s file system: xcr export xcr export The same guidelines above regarding importing configurations also apply to exporting configurations. If no groups are specified, then the export command will export all configuration settings to the file. If instances are specified after the groups, only those group instances are written. If no instance is specified, all instances of that group are written.
Exporting The following example exports only the accept mode tunneling settings for line 1 to the file “tunnel_1.xcr” on the device server filesystem: xcr export tunnel_1.xcr “tunnel accept:1” The following example exports only the connect mode tunneling settings for all ports to the file “tunnel_all.xcr” on the device server filesystem: xcr export tunnel_all.xcr “tunnel connect” The following example imports only the settings for line 2 from a XCR named “factory_config.xcr” on the device server filesystem. If “factory_config.xcr” has other configuration settings, they are ignored: xcr import factory_config.xcr “line:2” The following example imports only line settings for all ports from a configuration record on the device server filesystem named “foobar.xcr”: xcr import foobar.xcr “line” To import only disconnect mode tunneling settings for port 1 and serial line settings for port 2 from an XML configuration record named “production.xcr” that contains these settings (and possibly more), issue the following command: xcr import production.xcr "tunnel disconnect:1, line:2" The following example imports all tunneling settings and line settings for all serial ports from a file named xcr_file: xcr import xcr_file "tunnel accept, tunnel connect, tunnel disconnect, tunnel modem, tunnel packing, tunnel serial, tunnel start, tunnel stop, line" The following example exports only accept mode tunneling settings on serial port 1, and line settings on serial port 2 to a file named tunnel_config_t1_l2.xcr on the device server filesystem. xcr export tunnel_config_t1_l2.xcr "tunnel accept:1, line:2" The following example exports connect mode tunneling and line settings for all ports to the file tunnel_config.xcr on the device server filesystem: xcr export tunnel_config.xcr "tunnel, line"
Passwords in the XML File If you log in to a device server to which you will be pasting an XCR, you do not need to include passwords in the file, because you are already logged into the device. However, if you send an
MatchPort® AR Embedded Device Server Command Reference 19 4: Configuration Using XML
XCR to one or more devices that are password protected, you can include the appropriate passwords in the XCR and skip the login steps. The “xml paste passwords” name is used with the “passwords” name and “cli login” and “cli enable level” values to specify the passwords to use when the device has been configured with password protection. The password value is clear text. To protect the password, establish an SSH connection to the device server. Figure 4-7 shows an example.
Figure 4-7 XML Example of Supplying Passwords
XML Configuration Groups Table 4-8 lists the MatchPort AR XCR groups in alphabetical order. This table indicates the various group items, as well as some possible value names and options.
Note: Any instance of < in the table may be read as < (the html encoded form for less than) and any instance of > may be read as > (the html encoded form for greater than).
Table 4-8 XCR Groups
Group Name Group Item Value Name Value Options Additional Information arp arp delete ip address Remove an entry from the ARP table. Specify the entry by its IP address. arp entry ip address mac address timeout Default: 60 seconds cli login password Value is SECRET, hidden from user view. enable level password Value is SECRET, hidden from user view.
MatchPort® AR Embedded Device Server Command Reference 20 4: Configuration Using XML
Group Name Group Item Value Name Value Options Additional Information cli (continued) quit connect line Accepts text containing control characters, for example, <control> A represents control-A Default: L
inactivity timeout <None>, Default: 15 ... minutes cp group state enable Changes state of the CP group. (Attribute of disable “instance” is required for the cp bit Bit number group name.) (Attribute of “instance is a type input number.) output assert low enable disable device short name long name serial number firmware version Read only. diagnostics log output disable, filesystem, Default: disable line max length Default: 50 Kbytes severity level debug, information, Default: debug notice, warning, error email to Multiple addresses (Attribute of may be separated “instance” is a with semicolons. number.) cc Multiple addresses may be separated with semicolons. from reply to subject message file overriding domain server port Default: 25 local port <Random>, ... Default:
MatchPort® AR Embedded Device Server Command Reference 21 4: Configuration Using XML
Group Name Group Item Value Name Value Options Additional Information email priority urgent, high, normal, Default: normal (Attribute of low, very low “instance” is a number.) (continued) cp group trigger value group trigger value ethernet speed auto, 10, 100 Default: auto (Attribute of duplex auto, half, full Default: auto “instance” is “eth0”.) ftp server state enable, disable Default: enable admin username Default: admin admin password Value is SECRET, hidden from user view. host name (Attribute of protocol telnet, ssh Default: telnet “instance” is a number.) ssh username remote address remote port Default: 0 http user delete name Deletes an HTTP authentication uri Authentication URI (Attribute of user. The value “instance” is the element is used to URI.) specify the user for deletion. realm type user password (Attribute of “instance” is the user name.) http server state enable, disable Default: enable port <None>, ... Default: 80 secure port <None>, ... Default: 443 secure protocols ssl3, tls1.0, tls1.1 May contain zero, one, or more of the values, separated by commas. Default: ssl3, tls1.0, tls1.1 max timeout Default: 10 seconds
MatchPort® AR Embedded Device Server Command Reference 22 4: Configuration Using XML
Group Name Group Item Value Name Value Options Additional Information http server max bytes Default: 40960 (continued) logging state enable, disable Default: enable max log entries Default: 50 log format Default: %h %t "%r" %s %B "%{Referer}i" "%{User-Agent}i" authentication timeout Default: 30 minutes icmp state enable, disable Default: enable interface bootp enable, disable Default: disable (Attribute of “instance” is “eth0”) dhcp enable, disable Default: enable ip address <None>, ... Accepts an IP address and mask as either: (1) IP address only (192.168.1.1) gets a default mask, (2) CIDR (192.168.1.1/24), or (3) Explicit mask (192.168.1.1 255.255.255.0). default gateway <None>, ... Accepts in IP address in dotted notation, like 192.168.1.1. hostname domain dhcp client id Set the identity of the client device. primary dns <None>, ... Accepts in IP address in dotted notation, like 192.168.1.1. secondary dns <None>, ... Accepts in IP address in dotted notation, like 192.168.1.1. mtu ip multicast time to live Default: 1 hops ip time to live
MatchPort® AR Embedded Device Server Command Reference 23 4: Configuration Using XML
Group Name Group Item Value Name Value Options Additional Information ip filter delete entries enable, disable If enabled, deletes any existing entries before adding “filter entry”. filter delete ip address Deletes a specific IP filter entry. net mask Deletes a specific IP filter entry. filter entry ip address If configured, is a specific IP address. net mask If configured, is a specific net mask. line name (Attribute of interface rs232, rs485 half- Default: “instance” is a duplex, rs485 full- number.) duplex state enable, disable Default: depends on instance protocol none, tunnel, ppp, Default: lpd baud rate Default: 9600 bits per second parity even, none, odd Default: none data bits 7, 8 Default: 8 stop bits 1, 2 Default: 1 flow control none, hardware, Default: none software xon char Accepts a control character, for example, <control> A represents control-A Default: Q xoff char Accepts a control character, for example, <control> A represents control-A Default: S
gap timer <None>, Default: none ... threshold Default: 56 bytes
MatchPort® AR Embedded Device Server Command Reference 24 4: Configuration Using XML
Group Name Group Item Value Name Value Options Additional Information lpd banner enable, disable Default: enable (Attribute of “instance” is a number.) binary enable, disable Default: disable soj enable, disable Default: disable eoj enable, disable Default: disable formfeed enable, disable Default: disable convert newline enable, disable Default: disable soj text eoj text queue name modbus tcp server state enable, disable Default: disable additional port <None>, ... Default: response timeout Default: 3000 milliseconds rss trace input enable, disable Default: disable ppp local ip <None>), ... Accepts an IP (Attribute of address and mask “instance” is a as either: (1) IP number.) address only (192.168.1.1) gets a default mask, (2) CIDR (192.168.1.1/24), or (3) Explicit mask (192.168.1.1 255.255.255.0). peer ip <None>), ... Accepts in IP address in dotted notation, like 192.168.1.1. authentication mode none, pap, chap, ms- Default: none chap, ms-chapv2 username password Value is SECRET, hidden from user view. query port state enable, disable rss feed enable, disable Default: disable persist enable, disable Default: disable max entries Default: 100
MatchPort® AR Embedded Device Server Command Reference 25 4: Configuration Using XML
Group Name Group Item Value Name Value Options Additional Information serial command mode mode echo serial string (Attribute of “instance” is a serial string number.) signon message wait time cp group trigger value smtp relay address relay port Default: 25 snmp state enable, disable Default: enable read community Value is SECRET, hidden from user view. Default: public write community Value is SECRET, hidden from user view. Default: private system contact system name Default: system description Default: system location traps state enable, disable Default: enable primary destination secondary destination ssh state enable, disable Default: enable port Default: 22 max sessions Default: 3 ssh client delete known hosts enable, disable If enabled, deletes any existing hosts before adding “known host”. known host delete name Specify the known host to delete. known host public rsa key (Attribute of “instance” is public dsa key required for the known host name) delete client users enable, disable If enabled, deletes any existing client users before adding “client user”.
MatchPort® AR Embedded Device Server Command Reference 26 4: Configuration Using XML
Group Name Group Item Value Name Value Options Additional Information ssh client client user delete name (continued) client user password (Attribute of “instance” is remote command required for the user name) public rsa key private rsa key public dsa key private dsa key ssh server host rsa keys public key private key host dsa keys public key private key delete authorized users authorized user delete name authorized user password (Attribute of “instance” is public rsa key required for the authorized user name) public dsa key ssl RSA certificate certificate Enter the text of the certificate. private key Enter the text of the private key. If configured and not exporting secrets, exports only a placeholder. DSA certificate certificate Enter the text of the certificate. private key Enter the text of the private key. If configured and not exporting secrets, exports only a placeholder. trusted ca enable, disable delete all cas enable, disable If enabled, deletes any existing trusted cas before adding “trusted ca”.
MatchPort® AR Embedded Device Server Command Reference 27 4: Configuration Using XML
Group Name Group Item Value Name Value Options Additional Information syslog state enable, disable Default: disable host local port Default: 514 remote port Default: 514 severity log level none, emergency, Default: none alert, critical, error, warning, notice, information, debug tcp resets enable, disable Default: enable ack limit Number of packets received before an ACK is forced. Default: 3 packets send data standard, expedited Default: standard tcp (continued) max retrans max retrans syn ack send data telnet state enable, disable Default: enable port Default: 23 max sessions Default: 3 terminal terminal type Default: (Attribute of UNKNOWN “instance” is login connect menu enable, disable Default: disable either “network” or a number.) exit connect menu enable, disable Default: disable send break Accepts a control character, for example, <control> A represents control-A break duration Default: 500 milliseconds echo enable, disable Default: enable tftp server state enable, disable Default: enable allow file creation enable, disable Default: disable allow firmware update enable, disable Default: disable allow xcr import enable, disable Default: disable tunnel accept accept mode disable, always, any Default: always (Attribute of character, start “instance” is a character, modem number.) control asserted, modem emulation
MatchPort® AR Embedded Device Server Command Reference 28 4: Configuration Using XML
Group Name Group Item Value Name Value Options Additional Information tunnel accept start character Accepts a control (Attribute of character, for “instance” is a example, number.) <control> (continued) A represents control-A Default: B flush start character enable, disable Default: enable local port <None>, ... Default: protocol tcp, ssh, telnet, tcp Default: tcp aes, ssl tcp keep alive <None>, ... Default: 45000 milliseconds aes encrypt key Value is SECRET, hidden from user view. tunnel accept aes decrypt key Value is SECRET, (Attribute of hidden from user “instance” is a view. number.) flush serial enable, disable Default: disable (continued) block serial enable, disable Default: disable block network enable, disable Default: disable password password Value is SECRET, hidden from user view. prompt enable, disable Default: disable email connect <None>, ... Default: email disconnect <None>, ... Default: cp output group connection value disconnection value tunnel connect connect mode disable, always, any Default: disable (Attribute of character, start “instance” is a character, modem number.) control asserted, modem emulation
start character Accepts a control character, for example, <control> A represents control-A Default: B flush start character enable, disable Default: enable
MatchPort® AR Embedded Device Server Command Reference 29 4: Configuration Using XML
Group Name Group Item Value Name Value Options Additional Information tunnel connect local port <Random>, ... Default: (Attribute of “instance” is a number.) (continued) host (Attribute of vip enable, disable Default: disable “instance” is a number.) vip name address port protocol ssh username validate certificate tcp keep alive <Random>, ... aes encrypt key aes decrypt key host mode sequential, simultaneous Default: sequential tunnel connect reconnect time Default: 15000 (Attribute of milliseconds “instance” is a flush serial enable, disable Default: disable number.) (continued) block serial enable, disable Default: disable block network enable, disable Default: disable email connect <None>, ... Default: email disconnect <None>, ... Default: cp output goup connection value, disconnection value connection value disconnection value tunnel stop character Accepts a control disconnect character, for (Attribute of example, “instance” is a <control> number.) A represents control-A flush step character enable, disable Default: disable modem control enable, disable Default: disable timeout Default: 0 milliseconds flush serial enable, disable Default: disable
MatchPort® AR Embedded Device Server Command Reference 30 4: Configuration Using XML
Group Name Group Item Value Name Value Options Additional Information tunnel modem echo pluses enable, disable Default: disable (Attribute of echo commands enable, disable Default: enable “instance” is a number.) verbose response enable, disable Default: enable response type text, numeric Default: text error unknown enable, disable Default: disable commands incoming connection disabled, automatic, Default: disabled manual connect string display remote ip enable, disable Default: disable tunnel packing packing mode disable, timeout, Default: disable (Attribute of send character “instance” is a timeout Default: 1000 number.) milliseconds threshold Default: 512 bytes send character Accepts a control character, for example, <control> A represents control-A Default: M trailing character Accepts a control character, for example, <control> A represents control-A tunnel serial dtr asserted while Default: asserted (Attribute of connected, while connected “instance” is a continuously number.) asserted, unasserted, truport xml import restore factory control configuration delete cpm groups enable, disable cpm group delete name delete http authentication enable, disable Deletes existing uris http authentication uris before importing new ones. http authentication uri name Deletes the delete specified http authentication uri. reboot enable, disable Reboots after importing.
MatchPort® AR Embedded Device Server Command Reference 31 4: Configuration Using XML
XML Status Record Groups and Items Table 4-9 lists the supported XML Status Record (XSR) groups and items. These groups and items show the status of the device in XML form and can only be exported. The XSR schema differs slightly from the XCR groups and items in that the XSR allows groups within groups. Currently, the only XSR groups that contain any sub groups are buffer pools and tunnel. The buffer pools group has the following sub groups:
Protocol stack
Ethernet driver
Line The tunnel group has the following sub groups:
Tunnel Modem
Table 4-9 XSR Groups and Items Group Name Item Name Value Name Valid Values arp arp entry ip address (Attribute of “instance” is mac address “eth0”.) age type dynamic static buffer pool this group contains other groups: ethernet driver, protocol stack cp group state disabled (Attribute of “instance” is disabled and locked required for the group name. enabled enabled and locked value cp value (Attribute of “instance” is a level low number.) high logic inverted not inverted position
MatchPort® AR Embedded Device Server Command Reference 32 4: Configuration Using XML
Group Name Item Name Value Name Valid Values cps cp pin (Attribute of “instance”is a configured as input number.) output value level low high logic inverted not inverted active group group device product info product type serial number firmware version uptime permanent config saved unsaved email success sent (Attribute of “instance” is a sent with retries number.) failed queued email log entry time (Attribute of “instance” is a log number.) ethernet driver buffer headers total (Within group “buffer pool”.) free used max used cluster pool cluster size total free used max used filesystem filesystem size banks current A B firmware begin firmware end firmware erase cycles firmware 2 begin
MatchPort® AR Embedded Device Server Command Reference 33 4: Configuration Using XML
Group Name Item Name Value Name Valid Values filesystem (continued) banks (continued) firmware 2 end firmware 2 erase cycles bank a begin bank a end bank a erase cycles bank b begin bank b end bank b erase cycles available space clean space dirty space file and dir space used data space used number of files number of directories number of system files opened files locked files opened for sharing busy yes no ftp status running inactive connections rejected accepted last client ip address port hardware cpu type speed memory flash size ram size http state enabled disabled logging entries bytes
MatchPort® AR Embedded Device Server Command Reference 34 4: Configuration Using XML
Group Name Item Name Value Name Valid Values http log entry (Attribute of “instance” is a number.) totals entries bytes icmp in messages messages discarded errors destination unreachable time exceeded messages parameter problems source quench requests redirects ping requests ping replies timestamp requests timestamp replies address mask requests address mask replies out messages messages discarded errors destination unreachables time exceeded messages parameter problems source quench requests redirects ping requests ping replies timestamp requests timestamp replies address mask requests address mask replies
MatchPort® AR Embedded Device Server Command Reference 35 4: Configuration Using XML
Group Name Item Name Value Name Valid Values interface generic status no link (Attribute of “instance” is link up “eth0”.) disabled unknown errors (error text) none ethernet (Present only for speed 10 eth0.) 100 duplex full half arp encapsulation ARPA type ARPA timeout default gateway network mask domain mac address hostname ip address last change mtu primary dns secondary dns
MatchPort® AR Embedded Device Server Command Reference 36 4: Configuration Using XML
Group Name Item Name Value Name Valid Values interface transmit octets (Attribute of “instance” is unicast “eth0”.) (continued) non unicast discards errors broadcast packets multicast packets filtered packets deferred multiple retries one retry underflows late collisions retry errors carrier lost errors receive octets unicast non unicast discards errors broadcast packets multicast packets filtered packets unknown protocol framing errors overflows crc errors missed frame errors ip state enabled disabled default ttl forwarded route discards
MatchPort® AR Embedded Device Server Command Reference 37 4: Configuration Using XML
Group Name Item Name Value Name Valid Values ip sockets ip socket protocol UDP TCP rx queue tx queue local address local port remote address remote port state line receiver bytes (Attribute of “instance” is a breaks number.) parity errors framing errors overrun errors no receive buffer errors queued bytes flow control n/a stop go transmitter bytes breaks queued bytes flow control n/a stop go line levels cts asserted not asserted rts asserted not asserted dsr asserted not asserted dtr asserted not asserted line (With no instance.) state enable (Within group “line” with disable instance.) protocol tunnel baud rate Any value from 300 to 230400.
MatchPort® AR Embedded Device Server Command Reference 38 4: Configuration Using XML
Group Name Item Name Value Name Valid Values line (With no instance.) parity even (Within group “line” with instance.) (continued) none odd data bits 7 8 stop bits 1 2 flow control hardware none software xon char xoff char lpd jobs printed (Attribute of “instance” is a bytes printed number.) current client ip address current client port last client ip address last client port memory main heap condition clean corrupt total memory available memory fragments allocated blocks modbus local slave totals pdus in pdus out exceptions modbus tcp server state down (Attribute of “instance” is up “permanent” or “additional”.) binding no port local port totals uptime pdus in pdus out connections last connection local ip address local port
MatchPort® AR Embedded Device Server Command Reference 39 4: Configuration Using XML
Group Name Item Name Value Name Valid Values modbus tcp server remote ip address (Attribute of “instance” is remote port “permanent” or “additional”.) (continued) processes process cpu % (Attribute of “instance” is a stack used number.) stack size thread name protocol stack (within group buffer headers total “buffer pool”) free used max used cluster pool cluster size total free used max used query port status enabled disabled last connection ip address port in discoveries unknown queries erroneous packets out discovery replies errors rss url data entries bytes sessions line baud parity data bits stop bits flow control ssh state active waiting disabled totals uptime bytes in bytes out
MatchPort® AR Embedded Device Server Command Reference 40 4: Configuration Using XML
Group Name Item Name Value Name Valid Values status messages failed syslog messages send tcp retransmission algorithm vanj timeout minimum timeout maximum connections maximum open active open passive failed resets established errors in resets in out segments in out retransmitted telnet state active waiting disabled totals uptime bytes in bytes out last connection local ip address local port remote ip address remote port tftp downloaded uploaded status running inactive not found errors read write unknown last client ip address port
MatchPort® AR Embedded Device Server Command Reference 41 4: Configuration Using XML
Group Name Item Name Value Name Valid Values tunnel aggregate completed connects (Attribute of “instance” is a completed accepts number.) disconnects dropped connects dropped accepts octets from serial octets from network connect connection time accept connection time connect dns address changes connect dns address invalids tunnel modem (within group echo commands enable “tunnel”) disable verbose response enable disable response type text numeric error unknown commands disable enable incoming connection disabled automatic manual udp in unknown ports in datagrams in errors out datagrams xsr out bytes lines elements errors
MatchPort® AR Embedded Device Server Command Reference 42 5: Commands and Levels
Click the level in the tree structure and it will take you to the command list for that level.
Table 5-1 Commands and Levels accept (tunnel-accept:2) level commands accept mode always Enables the tunneling server to always accept tunneling connections. accept mode any character Enables the tunneling server to accept tunneling connec- tions only when a character is received through the corresponding line (seri- al port). accept mode disable Disables accept mode tunneling. accept mode modem control asserted Enables the tunneling server to accept tunneling connec- tions when the modem control pin is asserted. accept mode modem emulation Enables modem emulation for accept mode tunneling. accept mode start character Enables accept mode tunneling when the configured start character is received on the line. aes decrypt key Sets the accept tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the accept tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces.
MatchPort® AR Embedded Device Server Command Reference 45 5: Commands and Levels
aes encrypt key Sets the accept tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the accept tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. block network disable Forwards (tunnels) network data in accept mode tunnel- ing. block network enable Discards all data coming in from the accept mode tunnel before forwarding it to the serial interface (generally used for debugging). block serial disable Forwards (tunnels) serial data in accept mode tunneling. block serial enable Discards all data coming in from the serial interface before forwarding it to the accept mode tunnel (generally used for debug- ging). clrscrn Clears the screen. cp output Enters the next lower level. default accept mode Restores the default accept mode as "always". default protocol Restores the default protocol as "TCP". default start character Defaults the accept mode start character. default tcp keep alive Restores the default 45 second accept mode TCP keep alive timeout. email connect Sets an email profile to use to send an email alert upon establishing an accept mode tunnel. = the number of the email profile to use. email disconnect Sets an email profile to use to send an email alert upon closing an accept mode tunnel. = the number of the email profile to use. exit Returns to the tunnel level. flush serial disable Characters already in the serial data buffer are retained upon establishing an accept mode tunneling connection. flush serial enable Flushes the serial data buffer upon establishing an accept mode tunneling connection. flush start character disable Enables forwarding of the accept start character into the network. flush start character enable Disables forwarding of the accept start character into the network. kill connection Disconnects the active accept mode tunneling connection. local port Sets the port to use for accept mode tunneling. = number of the port to use. no aes decrypt key Removes the accept tunnel AES decrypt key. no aes encrypt key Removes the accept tunnel AES encrypt key.
MatchPort® AR Embedded Device Server Command Reference 46 5: Commands and Levels
no email connect Discontinues sending email alerts upon establishing an accept mode tunnel. no email disconnect Discontinues sending email alerts upon closing an accept mode tunnel. no local port Uses the default port number as the local port for accept mode tunneling. The default port is 10000 + #, where # is the line number for this tunnel. no tcp keep alive Disables the accept mode TCP keep alive timeout. password Enters the next lower level. protocol ssh Uses SSH protocol for accept mode tunneling. protocol ssl Uses SSL protocol for accept mode tunneling. protocol tcp Uses TCP protocol for accept mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for accept mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for accept mode tunnel- ing. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. show status Displays tunnel accept status. start character Sets the accept mode start character. The character may be input as text, control, decimal, or hex. A control character has the form C. A decimal value character has the form \99. A hex value character has the form 0xFF. tcp keep alive Enables TCP keep alive for accept mode tunneling and sets the timer. = timer value, in milliseconds. write Stores the current configuration in permanent memory. accept (tunnel-accept:1) level commands accept mode always Enables the tunneling server to always accept tunneling connections. accept mode any character Enables the tunneling server to accept tunneling connec- tions only when a character is received through the corresponding line (seri- al port). accept mode disable Disables accept mode tunneling. accept mode modem control asserted Enables the tunneling server to accept tunneling connec- tions when the modem control pin is asserted. accept mode modem emulation Enables modem emulation for accept mode tunneling. accept mode start character Enables accept mode tunneling when the configured start character is received on the line. aes decrypt key Sets the accept tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces.
MatchPort® AR Embedded Device Server Command Reference 47 5: Commands and Levels
aes decrypt key text Sets the accept tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the accept tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the accept tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. block network disable Forwards (tunnels) network data in accept mode tunnel- ing. block network enable Discards all data coming in from the accept mode tunnel before forwarding it to the serial interface (generally used for debugging). block serial disable Forwards (tunnels) serial data in accept mode tunneling. block serial enable Discards all data coming in from the serial interface before forwarding it to the accept mode tunnel (generally used for debug- ging). clrscrn Clears the screen. cp output Enters the next lower level. default accept mode Restores the default accept mode as "always". default protocol Restores the default protocol as "TCP". default start character Defaults the accept mode start character. default tcp keep alive Restores the default 45 second accept mode TCP keep alive timeout. email connect Sets an email profile to use to send an email alert upon establishing an accept mode tunnel. = the number of the email profile to use. email disconnect Sets an email profile to use to send an email alert upon closing an accept mode tunnel. = the number of the email profile to use. exit Returns to the tunnel level. flush serial disable Characters already in the serial data buffer are retained upon establishing an accept mode tunneling connection. flush serial enable Flushes the serial data buffer upon establishing an accept mode tunneling connection. flush start character disable Enables forwarding of the accept start character into the network. flush start character enable Disables forwarding of the accept start character into the network. kill connection Disconnects the active accept mode tunneling connection.
MatchPort® AR Embedded Device Server Command Reference 48 5: Commands and Levels
local port Sets the port to use for accept mode tunneling. = number of the port to use. no aes decrypt key Removes the accept tunnel AES decrypt key. no aes encrypt key Removes the accept tunnel AES encrypt key. no email connect Discontinues sending email alerts upon establishing an accept mode tunnel. no email disconnect Discontinues sending email alerts upon closing an accept mode tunnel. no local port Uses the default port number as the local port for accept mode tunneling. The default port is 10000 + #, where # is the line number for this tunnel. no tcp keep alive Disables the accept mode TCP keep alive timeout. password Enters the next lower level. protocol ssh Uses SSH protocol for accept mode tunneling. protocol ssl Uses SSL protocol for accept mode tunneling. protocol tcp Uses TCP protocol for accept mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for accept mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for accept mode tunnel- ing. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. show status Displays tunnel accept status. start character Sets the accept mode start character. The character may be input as text, control, decimal, or hex. A control character has the form C. A decimal value character has the form \99. A hex value character has the form 0xFF. tcp keep alive Enables TCP keep alive for accept mode tunneling and sets the timer. = timer value, in milliseconds. write Stores the current configuration in permanent memory. arp (config-arp) level commands add Adds an entry to the ARP table, mapping an IP address to a MAC address. = IP address to be mapped. = MAC address in colon-separated form. clrscrn Clears the screen. default timeout Restores the default ARP cache timeout. exit Exits to the configuration level. remove all Removes all entries from the ARP cache. remove ip Removes an entry from the ARP cache. = address of the entry being removed. show Displays the current configuration. show cache Displays the ARP cache table. show history Displays the last 20 commands entered during the current CLI session. timeout Sets the ARP cache timeout. = ARP cache timeout in seconds.
MatchPort® AR Embedded Device Server Command Reference 49 5: Commands and Levels
write Stores the current configuration in permanent memory. cli (config-cli) level commands clrscrn Clears the screen. default inactivity timeout The default inactivity timeout will apply to CLI sessions. default quit connect line Restores the default string used to quit the "connect line " command. enable level password Sets the enable-level password. exit Exits to the configuration level. inactivity timeout Sets the inactivity timeout for all CLI sessions. login password Sets the CLI login password. no enable level password Removes the enable-level password. no inactivity timeout No inactivity timeout will apply to CLI sessions. no login password Removes the CLI login password. quit connect line Sets the string used to quit the "connect line " com- mand. The characters may be input as text or control. A control character has the form C. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. ssh Change to menu level for SSH configuration and status. telnet Change to menu level for Telnet configuration and status. write Stores the current configuration in permanent memory. client (ssh-client) level commands clrscrn Clears the screen. default user command Restore the user command to the default login shell delete all known hosts Remove all hnown hosts delete all users Remove all users delete known host Remove known host delete user Delete the named user exit Exits to the ssh level. known host Set known host RSA or DSA key no known host dsa Remove known host DSA key no known host rsa Remove known host RSA key no user dsa Remove user DSA key no user rsa Remove user RSA key show Show SSH Client settings show history Displays the last 20 commands entered during the current CLI session. show known host Show known host RSA and DSA keys show user Show information for a user user Set username and RSA or DSA keys user command Customizes the user command user generate dsa 1024 Generate DSA public and private keys user generate dsa 512 Generate DSA public and private keys user generate dsa 768 Generate DSA public and private keys user generate rsa 1024 Generate RSA public and private keys
MatchPort® AR Embedded Device Server Command Reference 50 5: Commands and Levels
user generate rsa 512 Generate RSA public and private keys user generate rsa 768 Generate RSA public and private keys user password Set username with password and optional RSA or DSA keys write Stores the current configuration in permanent memory. configure (config) level commands arp Changes to the command level for ARP configuration and status. cli Change to menu level for CLI configuration and status clrscrn Clears the screen. diagnostics Enters the diagnostics level. exit Exits to the enable level. ftp Enters the ftp level. host Change to config host level http Enters the http level. icmp Changes to the command level for ICMP configuration and status. if Changes to the interface configuration level. ip Changes to the command level for IP configuration and status. ip filter Enters the config-filter level. kill ssh Kills SSH session with index from "show sessions" kill telnet Kills Telnet session with index from "show sessions" lpd Enters the configure lpd level. = number of the line (lpd serial port) to be config- ured. modbus Changes to the modbus configuration level. query port Enters the query port level. rss Change to menu level for RSS configuration and status show Displays system information. show history Displays the last 20 commands entered during the current CLI session. smtp Changes to the command level for SMTP configuration and status. snmp Enters the snmp level. syslog Enters the syslog level. tcp Changes to the command level for TCP configuration and status. terminal Enters the configure-terminal level. = number of the terminal line (serial port) to be con- figured. terminal network Enters the configure-terminal level for the network. tftp Enters the tftp level. udp Changes to the command level for UDP configuration and status. vip Change to menu level for VIP configuration and status write Stores the current configuration in permanent memory. connect (tunnel-connect:2) level commands block network disable Forwards (tunnels) network data in connect mode tunnel-
MatchPort® AR Embedded Device Server Command Reference 51 5: Commands and Levels
ing. block network enable Discards all data coming in from the connect mode tunnel before forwarding it to the serial interface (generally used for debugging). block serial disable Forwards (tunnels) serial data in connect mode tunneling. block serial enable Discards all data coming in from the serial interface before forwarding it to the connect mode tunnel (generally used for debug- ging). clrscrn Clears the screen. connect mode always Enables the tunneling server to always establish tunneling connections. connect mode any character Enables the tunneling server to establish a tunneling con- nection when a character is received on the corresponding line (serial port). connect mode disable Disables connect mode tunneling. connect mode modem control asserted Enables the tunneling server to make tunneling connec- tions when the modem control pin is asserted. connect mode modem emulation Enables modem emulation for connect mode tunneling. connect mode start character Enables connect mode tunneling when the configured start character is received on the line. cp output Enters the next lower level. default connect mode Restores the default connect mode as "disable". default host mode Connects to the first host in the list that accepts the con- nection. default local port Uses a random port number as the local port for establish- ing tunneling connections to other devices. default reconnect time Restores the default reconnect time value for connect mode tunneling. default start character Defaults the connect mode start character. email connect Sets an email profile to use to send an email alert upon establishing a connect mode tunnel. = the number of the email profile to use. email disconnect Sets an email profile to use to send an email alert upon closing a connect mode tunnel. = the number of the email profile to use. exit Returns to the tunnel level. flush serial disable Characters already in the serial data buffer are retained upon establishing a connect mode tunneling connection. flush serial enable Flushes the serial data buffer upon establishing a connect mode tunneling connection. flush start character disable Enables forwarding of the connect start character into the network. flush start character enable Disables forwarding of the connect start character into the network.
MatchPort® AR Embedded Device Server Command Reference 52 5: Commands and Levels
host Enters the next lower level. Specify the instance for the next lower level. host mode sequential Connects to the first host in the list that accepts the con- nection. host mode simultaneous Selects simultaneous connections to all hosts on the host list. kill connection Disconnects the active connect mode tunneling connec- tion or connections. local port Sets a specific port for use as the local port. = the number of the port to use. no email connect Discontinues sending email alerts upon establishing a connect mode tunnel. no email disconnect Discontinues sending email alerts upon closing a connect mode tunnel. promote host Promotes the identified host, exchanging it place with the host above it, to adjust the order of the defined hosts. reconnect time Sets the reconnect time value for tunneling connections established by the device in milliseconds. = timeout in milliseconds. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. show status Displays tunnel connect status. start character Sets the connect mode start character. The character may be input as text, control, decimal, or hex. A control character has the form C. A decimal value character has the form \99. A hex value character has the form 0xFF. write Stores the current configuration in permanent memory. connect (tunnel-connect:1) level commands block network disable Forwards (tunnels) network data in connect mode tunnel- ing. block network enable Discards all data coming in from the connect mode tunnel before forwarding it to the serial interface (generally used for debugging). block serial disable Forwards (tunnels) serial data in connect mode tunneling. block serial enable Discards all data coming in from the serial interface before forwarding it to the connect mode tunnel (generally used for debug- ging). clrscrn Clears the screen. connect mode always Enables the tunneling server to always establish tunneling connections. connect mode any character Enables the tunneling server to establish a tunneling con- nection when a character is received on the corresponding line (serial port). connect mode disable Disables connect mode tunneling. connect mode modem control asserted Enables the tunneling server to make tunneling connec- tions when the modem control pin is asserted.
MatchPort® AR Embedded Device Server Command Reference 53 5: Commands and Levels
connect mode modem emulation Enables modem emulation for connect mode tunneling. connect mode start character Enables connect mode tunneling when the configured start character is received on the line. cp output Enters the next lower level. default connect mode Restores the default connect mode as "disable". default host mode Connects to the first host in the list that accepts the con- nection. default local port Uses a random port number as the local port for establish- ing tunneling connections to other devices. default reconnect time Restores the default reconnect time value for connect mode tunneling. default start character Defaults the connect mode start character. email connect Sets an email profile to use to send an email alert upon establishing a connect mode tunnel. = the number of the email profile to use. email disconnect Sets an email profile to use to send an email alert upon closing a connect mode tunnel. = the number of the email profile to use. exit Returns to the tunnel level. flush serial disable Characters already in the serial data buffer are retained upon establishing a connect mode tunneling connection. flush serial enable Flushes the serial data buffer upon establishing a connect mode tunneling connection. flush start character disable Enables forwarding of the connect start character into the network. flush start character enable Disables forwarding of the connect start character into the network. host Enters the next lower level. Specify the instance for the next lower level. host mode sequential Connects to the first host in the list that accepts the con- nection. host mode simultaneous Selects simultaneous connections to all hosts on the host list. kill connection Disconnects the active connect mode tunneling connec- tion or connections. local port Sets a specific port for use as the local port. = the number of the port to use. no email connect Discontinues sending email alerts upon establishing a connect mode tunnel. no email disconnect Discontinues sending email alerts upon closing a connect mode tunnel. promote host Promotes the identified host, exchanging it place with the host above it, to adjust the order of the defined hosts. reconnect time Sets the reconnect time value for tunneling connections established by the device in milliseconds. = timeout in milliseconds.
MatchPort® AR Embedded Device Server Command Reference 54 5: Commands and Levels
show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. show status Displays tunnel connect status. start character Sets the connect mode start character. The character may be input as text, control, decimal, or hex. A control character has the form C. A decimal value character has the form \99. A hex value character has the form 0xFF. write Stores the current configuration in permanent memory. cp (email-cp:4) level commands clrscrn Clears the screen. exit Exits to the next higher level. group Specify a CP group that shall trigger an email. = configurable pin group. no group Disables the trigger to send an email. no trigger value Clears the value that shall trigger an email. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. trigger value Specify a value of the CP group that shall trigger an email. = numeric value to watch for from the CP group. Can be specified as hex if prepended with “0x”. write Stores the current configuration in permanent memory. cp (email-cp:3) level commands clrscrn Clears the screen. exit Exits to the next higher level. group Specify a CP group that shall trigger an email. = configurable pin group. no group Disables the trigger to send an email. no trigger value Clears the value that shall trigger an email. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. trigger value Specify a value of the CP group that shall trigger an email. = numeric value to watch for from the CP group. Can be specified as hex if prepended with “0x”. write Stores the current configuration in permanent memory. cp (email-cp:2) level commands clrscrn Clears the screen. exit Exits to the next higher level. group Specify a CP group that shall trigger an email. = configurable pin group. no group Disables the trigger to send an email. no trigger value Clears the value that shall trigger an email. show Shows the current configuration. show history Displays the last 20 commands entered during the current
MatchPort® AR Embedded Device Server Command Reference 55 5: Commands and Levels
CLI session. trigger value Specify a value of the CP group that shall trigger an email. = numeric value to watch for from the CP group. Can be specified as hex if prepended with “0x”. write Stores the current configuration in permanent memory. cp (email-cp:1) level commands clrscrn Clears the screen. exit Exits to the next higher level. group Specify a CP group that shall trigger an email. = configurable pin group. no group Disables the trigger to send an email. no trigger value Clears the value that shall trigger an email. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. trigger value Specify a value of the CP group that shall trigger an email. = numeric value to watch for from the CP group. Can be specified as hex if prepended with “0x”. write Stores the current configuration in permanent memory. cp output (tunnel-connect-cp_output:2) level commands clrscrn Clears the screen. connection value Sets the value to output to the CP Group upon connect mode connection. = binary to output (typically 1 or 0). default connection value Restores the default value for connect mode connection. default disconnection value Restores the default value for connect mode disconnec- tion. disconnection value Sets the value to output to the CP Group upon connect mode disconnection. = binary to output (typically 1 or 0). exit Exits to the next higher level. group Configures the CP Group to set upon making or breaking a connect mode connection. = CP Group. no group Removes the CP Set Group for connect mode. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. write Stores the current configuration in permanent memory. cp output (tunnel-accept-cp_output:2) level commands clrscrn Clears the screen. connection value Sets the value to output to the CP Group upon accept mode connection. = binary to output (typically 1 or 0). default connection value Restores the default value for accept mode connection. default disconnection value Restores the default value for accept mode disconnection. disconnection value Sets the value to output to the CP Group upon accept mode disconnection.
MatchPort® AR Embedded Device Server Command Reference 56 5: Commands and Levels
= binary to output (typically 1 or 0). exit Exits to the next higher level. group Configures the CP Group to set upon making or breaking an accept mode connection. = CP Group. no group Removes the CP Set Group for accept mode. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. write Stores the current configuration in permanent memory. cp output (tunnel-connect-cp_output:1) level commands clrscrn Clears the screen. connection value Sets the value to output to the CP Group upon connect mode connection. = binary to output (typically 1 or 0). default connection value Restores the default value for connect mode connection. default disconnection value Restores the default value for connect mode disconnec- tion. disconnection value Sets the value to output to the CP Group upon connect mode disconnection. = binary to output (typically 1 or 0). exit Exits to the next higher level. group Configures the CP Group to set upon making or breaking a connect mode connection. = CP Group. no group Removes the CP Set Group for connect mode. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. write Stores the current configuration in permanent memory. cp output (tunnel-accept-cp_output:1) level commands clrscrn Clears the screen. connection value Sets the value to output to the CP Group upon accept mode connection. = binary to output (typically 1 or 0). default connection value Restores the default value for accept mode connection. default disconnection value Restores the default value for accept mode disconnection. disconnection value Sets the value to output to the CP Group upon accept mode disconnection. = binary to output (typically 1 or 0). exit Exits to the next higher level. group Configures the CP Group to set upon making or breaking an accept mode connection. = CP Group. no group Removes the CP Set Group for accept mode. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session.
MatchPort® AR Embedded Device Server Command Reference 57 5: Commands and Levels
write Stores the current configuration in permanent memory. cpm (cpm) level commands add to Adds the specified CP to the specified group. = configurable pin. = the name of the group to which you want to add the CP. add to Adds a specified CP to a specified group at a specified bit position. = configurable pin. = the name of the group to which you want to add the CP. = bit position. clrscrn Clears the screen. create Creates a configurable pin (CP) group. = the name for the new group. delete from Removes a CP from a specified group and sets the CP to its default configuration of input. = configurable pin. = the name of the group. delete Removes a group and resets all CPs in that group to the default configuration of input. = the name of the group. disable Disables the specified group. = the name of the group. enable Enables a disabled group. = the name of the group. exit Exits to the enable level. get Displays the value of the specified group. = the name of the group. set as input Configures a CP as an asserted high input. = configurable pin. set as input assert low Configures a CP as an asserted low input. = configurable pin. set as output Configures a CP as an asserted high output. = configurable pin. set as output assert low Configures a CP as an asserted low output. = configurable pin. set Assigns a value to the specified group. = the name of the group. = numeric value to assign to the CP group. Can be specified as hex if prepended with “0x”. show Displays group information for specified group. = the name of the group. show cp Displays configuration and group information for all CPs. show groups Displays all groups defined and their state. show history Displays the last 20 commands entered during the current CLI session. write Stores the current configuration in permanent memory. device (device) level commands auto show tlog Continuously displays the internal trouble log.
MatchPort® AR Embedded Device Server Command Reference 58 5: Commands and Levels
auto show upload Continuously displays the status of firmware upload. clrscrn Clears the screen. default long name Restores the default product long name. default short name Restores the default product short name. dhrystone Runs the Dhrystone benchmark program. exit Exit to the enable level. long name Sets the product long name, displayed in command mode and the Web interface. short name Sets the product short name, displayed in command mode and the Web interface. = maximum of eight characters. show Show system information show buffer pool Displays information about the various buffer pools. show codefile memory Displays memory utilization by code files. show delta memory Displays differences in memory utilization by code files or line reference. show hardware information Displays information about the hardware. show history Displays the last 20 commands entered during the current CLI session. show linereference memory Displays memory utilization by line reference for one code file. show matchport_ar Show system information show memory Displays current memory usage information. show task memory Displays task memory utilization. show task state Displays current task states. show tlog Displays the internal trouble log. show upload Displays the status of firmware upload. write Stores the current configuration in permanent memory. diagnostics (config-diagnostics) level commands clrscrn Clears the screen. exit Returns to the config level. log Enters the next lower level. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. write Stores the current configuration in permanent memory. disconnect (tunnel-disconnect:2) level commands clrscrn Clears the screen. exit Returns to the tunnel level. flush serial disable Does not flush serial data upon closing a tunneling con- nection. flush serial enable Flushes serial data buffer when a tunneling connection is closed. flush stop character disable Forwards the stop character from the Line to the network. flush stop character enable Prevents the stop character from the Line from being for- warded to the network. modem control disable Does not watch the modem control pin to disconnect. modem control enable Watches the modem control pin and disconnects if it is not asserted.
MatchPort® AR Embedded Device Server Command Reference 59 5: Commands and Levels
no stop character Removes the stop character. no timeout Disables disconnect after timeout feature for tunneling sessions. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. stop character Sets the stop character. The character may be input as text, control, decimal, or hex. A control character has the form C. A decimal value character has the form \99. A hex value character has the form 0xFF. timeout Disconnects when no data has been received on the line (serial port) for the specified length of time. = timeout in milliseconds. write Stores the current configuration in permanent memory. disconnect (tunnel-disconnect:1) level commands clrscrn Clears the screen. exit Returns to the tunnel level. flush serial disable Does not flush serial data upon closing a tunneling con- nection. flush serial enable Flushes serial data buffer when a tunneling connection is closed. flush stop character disable Forwards the stop character from the Line to the network. flush stop character enable Prevents the stop character from the Line from being for- warded to the network. modem control disable Does not watch the modem control pin to disconnect. modem control enable Watches the modem control pin and disconnects if it is not asserted. no stop character Removes the stop character. no timeout Disables disconnect after timeout feature for tunneling sessions. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. stop character Sets the stop character. The character may be input as text, control, decimal, or hex. A control character has the form C. A decimal value character has the form \99. A hex value character has the form 0xFF. timeout Disconnects when no data has been received on the line (serial port) for the specified length of time. = timeout in milliseconds. write Stores the current configuration in permanent memory. dns (dns) level commands clrscrn Clears the screen. exit Exits to the enable level. lookup Return a lookup on the DNS name or IP address. remove all Removes all entries from the DNS Cache.
MatchPort® AR Embedded Device Server Command Reference 60 5: Commands and Levels
remove host Removes an entry from the DNS Cache. show Show DNS status and cache entries. show history Displays the last 20 commands entered during the current CLI session. write Stores the current configuration in permanent memory. email 1 (email:1) level commands auto show statistics Continuously displays email statistics. cc Sets Cc addresses for email alerts. = a quoted, semicolon separated list of email ad- dresses. clear log Clears all entries from the mail log. clear mail counters Sets the email counters to zero. clrscrn Clears the screen. cp Enters the next lower level. default local port Sets the local port (used to send email alerts) to random. default priority Sets X-Priority for email alerts to 3 (normal). default server port Restores the factory default port for SMTP on the server side. email Enters the configure email level. exit Exits to the enable level. from Sets the From address for email alerts. = email address to place in the From field of the email alert. local port Sets the local port used to send email alerts. local port to use for email alerts. message file Specifies a text file, the contents of which will be the mes- sage body of an email alert. = the name of a local file. no cc Removes the Cc addresses for email alerts. no clear mail counters Restores the email counters to the aggregate values. no from Removes the From address for email alerts. no message file Removes the file name, so the message body will be empty. no overriding domain Removes the overriding domain name option. no reply to Removes the Reply To address for email alerts. no subject Removes subject used for email alerts. no to Removes the To addresses for email alerts. overriding domain Sets a domain name that will be used when connecting to an SMTP server to send an email alert instead of the device’s domain name in EHLO. = domain name to override the current domain name in EHLO. priority high Sets X-Priority for email alerts to 2 (high). priority low Sets X-Priority for email alerts to 4 (low). priority normal Sets X-Priority for email alerts to 3 (normal). priority urgent Sets X-Priority for email alerts to 1 (urgent). priority very low Sets X-Priority for email alerts to 5 (very low). reply to Sets the Reply To address for email alerts.
MatchPort® AR Embedded Device Server Command Reference 61 5: Commands and Levels
= email address to place in the Reply To field of the email alert. send Sends an email using the current settings. server port Sets the port used by the SMTP server. = port used for SMTP on the server side. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. show log Displays the email log. show statistics Displays email statistics. subject Sets the Subject for email alerts. = text to placed as the subject. to Sets To addresses for email alerts. = a quoted, semicolon separated list of email ad- dresses. write Stores the current configuration in permanent memory. email 2 (email:2) level commands auto show statistics Continuously displays email statistics. cc Sets Cc addresses for email alerts. = a quoted, semicolon separated list of email ad- dresses. clear log Clears all entries from the mail log. clear mail counters Sets the email counters to zero. clrscrn Clears the screen. cp Enters the next lower level. default local port Sets the local port (used to send email alerts) to random. default priority Sets X-Priority for email alerts to 3 (normal). default server port Restores the factory default port for SMTP on the server side. email Enters the configure email level. exit Exits to the enable level. from Sets the From address for email alerts. = email address to place in the From field of the email alert. local port Sets the local port used to send email alerts. local port to use for email alerts. message file Specifies a text file, the contents of which will be the mes- sage body of an email alert. = the name of a local file. no cc Removes the Cc addresses for email alerts. no clear mail counters Restores the email counters to the aggregate values. no from Removes the From address for email alerts. no message file Removes the file name, so the message body will be empty. no overriding domain Removes the overriding domain name option. no reply to Removes the Reply To address for email alerts. no subject Removes subject used for email alerts. no to Removes the To addresses for email alerts. overriding domain Sets a domain name that will be used when connecting to
MatchPort® AR Embedded Device Server Command Reference 62 5: Commands and Levels
an SMTP server to send an email alert instead of the device’s domain name in EHLO. = domain name to override the current domain name in EHLO. priority high Sets X-Priority for email alerts to 2 (high). priority low Sets X-Priority for email alerts to 4 (low). priority normal Sets X-Priority for email alerts to 3 (normal). priority urgent Sets X-Priority for email alerts to 1 (urgent). priority very low Sets X-Priority for email alerts to 5 (very low). reply to Sets the Reply To address for email alerts. = email address to place in the Reply To field of the email alert. send Sends an email using the current settings. server port Sets the port used by the SMTP server. = port used for SMTP on the server side. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. show log Displays the email log. show statistics Displays email statistics. subject Sets the Subject for email alerts. = text to placed as the subject. to Sets To addresses for email alerts. = a quoted, semicolon separated list of email ad- dresses. write Stores the current configuration in permanent memory. email 3 (email:3) level commands auto show statistics Continuously displays email statistics. cc Sets Cc addresses for email alerts. = a quoted, semicolon separated list of email ad- dresses. clear log Clears all entries from the mail log. clear mail counters Sets the email counters to zero. clrscrn Clears the screen. cp Enters the next lower level. default local port Sets the local port (used to send email alerts) to random. default priority Sets X-Priority for email alerts to 3 (normal). default server port Restores the factory default port for SMTP on the server side. email Enters the configure email level. exit Exits to the enable level. from Sets the From address for email alerts. = email address to place in the From field of the email alert. local port Sets the local port used to send email alerts. local port to use for email alerts. message file Specifies a text file, the contents of which will be the mes- sage body of an email alert. = the name of a local file.
MatchPort® AR Embedded Device Server Command Reference 63 5: Commands and Levels
no cc Removes the Cc addresses for email alerts. no clear mail counters Restores the email counters to the aggregate values. no from Removes the From address for email alerts. no message file Removes the file name, so the message body will be empty. no overriding domain Removes the overriding domain name option. no reply to Removes the Reply To address for email alerts. no subject Removes subject used for email alerts. no to Removes the To addresses for email alerts. overriding domain Sets a domain name that will be used when connecting to an SMTP server to send an email alert instead of the device’s domain name in EHLO. = domain name to override the current domain name in EHLO. priority high Sets X-Priority for email alerts to 2 (high). priority low Sets X-Priority for email alerts to 4 (low). priority normal Sets X-Priority for email alerts to 3 (normal). priority urgent Sets X-Priority for email alerts to 1 (urgent). priority very low Sets X-Priority for email alerts to 5 (very low). reply to Sets the Reply To address for email alerts. = email address to place in the Reply To field of the email alert. send Sends an email using the current settings. server port Sets the port used by the SMTP server. = port used for SMTP on the server side. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. show log Displays the email log. show statistics Displays email statistics. subject Sets the Subject for email alerts. = text to placed as the subject. to Sets To addresses for email alerts. = a quoted, semicolon separated list of email ad- dresses. write Stores the current configuration in permanent memory. email 4 (email:4) level commands auto show statistics Continuously displays email statistics. cc Sets Cc addresses for email alerts. = a quoted, semicolon separated list of email ad- dresses. clear log Clears all entries from the mail log. clear mail counters Sets the email counters to zero. clrscrn Clears the screen. cp Enters the next lower level. default local port Sets the local port (used to send email alerts) to random. default priority Sets X-Priority for email alerts to 3 (normal). default server port Restores the factory default port for SMTP on the server side.
MatchPort® AR Embedded Device Server Command Reference 64 5: Commands and Levels
email Enters the configure email level. exit Exits to the enable level. from Sets the From address for email alerts. = email address to place in the From field of the email alert. local port Sets the local port used to send email alerts. local port to use for email alerts. message file Specifies a text file, the contents of which will be the mes- sage body of an email alert. = the name of a local file. no cc Removes the Cc addresses for email alerts. no clear mail counters Restores the email counters to the aggregate values. no from Removes the From address for email alerts. no message file Removes the file name, so the message body will be empty. no overriding domain Removes the overriding domain name option. no reply to Removes the Reply To address for email alerts. no subject Removes subject used for email alerts. no to Removes the To addresses for email alerts. overriding domain Sets a domain name that will be used when connecting to an SMTP server to send an email alert instead of the device’s domain name in EHLO. = domain name to override the current domain name in EHLO. priority high Sets X-Priority for email alerts to 2 (high). priority low Sets X-Priority for email alerts to 4 (low). priority normal Sets X-Priority for email alerts to 3 (normal). priority urgent Sets X-Priority for email alerts to 1 (urgent). priority very low Sets X-Priority for email alerts to 5 (very low). reply to Sets the Reply To address for email alerts. = email address to place in the Reply To field of the email alert. send Sends an email using the current settings. server port Sets the port used by the SMTP server. = port used for SMTP on the server side. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. show log Displays the email log. show statistics Displays email statistics. subject Sets the Subject for email alerts. = text to placed as the subject. to Sets To addresses for email alerts. = a quoted, semicolon separated list of email ad- dresses. write Stores the current configuration in permanent memory. enable (enable) level commands auto show interfaces Show interface statistics auto show processes Continuously show thread runtime information
MatchPort® AR Embedded Device Server Command Reference 65 5: Commands and Levels
clear interfaces counters Zeros interface session counters clrscrn Clears the screen. configure Enters the configuration level. connect Show name and number for lines. connect line Begin session on serial port. cpm Enters the CP Manager level. device Enters the device level. disable Exits the enable level. dns Enters the DNS level. email Enters the configure email level. exit Exit from the system filesystem Enters the filesystem level. kill ssh Kills SSH session with index from "show sessions" kill telnet Kills Telnet session with index from "show sessions" line Enters the line level. = number of the line (serial port) to be configured. lpd Enters the lpd level. no clear interfaces counters Unzeros interface session counters ping Ping destination continuously with 5 second timeout ping Ping destination n times with 5 second timeout ping Ping destination n times with x timeout (in seconds) ppp Enters the serial line PPP level. reload Reboot system reload factory defaults Reload factory defaults to permanent storage show Show system information show history Displays the last 20 commands entered during the current CLI session. show interfaces Show interface statistics show ip sockets Show UDP/TCP state information show matchport_ar Show system information show processes Show thread runtime information show sessions Show active Telnet and SSH Sessions ssh Enters the SSH configuration level. ssh Begin SSH session on network . The optClientUserName must match an SSH Client: Us- ers configuration entry. Use "" in optClientUserName to prompt for host username and password. ssh Begin SSH session on network :. The optClientUserName must match an SSH Client: Us- ers configuration entry. Use "" in optClientUserName to prompt for host username and password. ssl Enters the SSL configuration level. telnet Begin telnet session on network . telnet Begin telnet session on network :. trace route Trace route to destination tunnel Enters the tunnel level. = number of the tunnel line (serial port) to be con-
MatchPort® AR Embedded Device Server Command Reference 66 5: Commands and Levels
figured. write Stores the current configuration in permanent memory. xml Enters the XML level. filesystem (filesystem) level commands cat Show the contents of a file cd Change the current directory to the specified directory clrscrn Clears the screen. compact Compact the file system, freeing all dirty space cp Copy an existing file dump Show contents of a file as a hex dump exit Exits to the enable level. format Format the file system and lose all data ls Show all files and directories in the current directory ls Show all files and directories in the specified directory mkdir Create a directory mv Move a file on the file system pwd Print working directory rm Remove a file rmdir Remove a directory show Show file system statistics show history Displays the last 20 commands entered during the current CLI session. show tree Show all files and directories from current directory tftp get ascii Get an ascii file using TFTP tftp get ascii Get an ascii file using TFTP tftp get binary Get a binary file using TFTP tftp get binary Get a binary file using TFTP tftp put ascii Put an ascii file using TFTP tftp put ascii Put an ascii file using TFTP tftp put binary Put a binary file using TFTP tftp put binary Put a binary file using TFTP touch Create a file ftp (config-ftp) level commands admin password Sets the administrative password for the FTP server. = administrative password. admin username Sets the administrative username for the FTP server. = administrative username. It also removes the administrative password. clear counters Zeros FTP counters. clrscrn Clears the screen. default admin username Resets the FTP username to the default (admin). exit Returns to the config level. no admin password Removes the FTP administrative password. no clear counters Unzeros FTP counters. show Displays the current configuration.
MatchPort® AR Embedded Device Server Command Reference 67 5: Commands and Levels
show history Displays the last 20 commands entered during the current CLI session. show statistics Displays the FTP statistics. state disable Disables the FTP server. state enable Enables the FTP server. write Stores the current configuration in permanent memory. host 1 (tunnel-connect-host:2:1) level commands address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use.
MatchPort® AR Embedded Device Server Command Reference 68 5: Commands and Levels
protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 1 (tunnel-connect-host:1:1) level commands address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces.
MatchPort® AR Embedded Device Server Command Reference 69 5: Commands and Levels
aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory.
MatchPort® AR Embedded Device Server Command Reference 70 5: Commands and Levels
host 1 (config-host:1) level commands clrscrn Clears the screen. default protocol Restores the default value of the protocol (Telnet). default remote port Sets the remote port (used to connect to the host) to the default value, which depends on the selected protocol. exit Exits to the configuration level. host Change to config host level name Sets the name of the host. = name of the host. no name Clears the name of the host. no remote address Clears the remote address of the host. no ssh username Clears the SSH username associated with the host. protocol ssh Sets the protocol to SSH. protocol telnet Sets the protocol to Telnet. remote address Sets the IP address of the remote host to connect to when this host is selected on the login connect menu. = IP address. remote port Sets the remote port used to connect to the host. = port to be used. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. ssh username Sets the username for logging into the host via SSH. = username. write Stores the current configuration in permanent memory. host 10 (tunnel-connect-host:2:10) level commands address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes.
MatchPort® AR Embedded Device Server Command Reference 71 5: Commands and Levels
Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 10 (tunnel-connect-host:1:10) level commands
MatchPort® AR Embedded Device Server Command Reference 72 5: Commands and Levels
address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling.
MatchPort® AR Embedded Device Server Command Reference 73 5: Commands and Levels
protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 10 (config-host:10) level commands clrscrn Clears the screen. default protocol Restores the default value of the protocol (Telnet). default remote port Sets the remote port (used to connect to the host) to the default value, which depends on the selected protocol. exit Exits to the configuration level. host Change to config host level name Sets the name of the host. = name of the host. no name Clears the name of the host. no remote address Clears the remote address of the host. no ssh username Clears the SSH username associated with the host. protocol ssh Sets the protocol to SSH. protocol telnet Sets the protocol to Telnet. remote address Sets the IP address of the remote host to connect to when this host is selected on the login connect menu. = IP address. remote port Sets the remote port used to connect to the host. = port to be used. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. ssh username Sets the username for logging into the host via SSH. = username. write Stores the current configuration in permanent memory. host 11 (tunnel-connect-host:2:11) level commands address Sets the remote host to establish tunneling connections with.
MatchPort® AR Embedded Device Server Command Reference 74 5: Commands and Levels
= IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode
MatchPort® AR Embedded Device Server Command Reference 75 5: Commands and Levels
tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 11 (tunnel-connect-host:1:11) level commands address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep
MatchPort® AR Embedded Device Server Command Reference 76 5: Commands and Levels
alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 11 (config-host:11) level commands clrscrn Clears the screen. default protocol Restores the default value of the protocol (Telnet). default remote port Sets the remote port (used to connect to the host) to the default value, which depends on the selected protocol. exit Exits to the configuration level. host Change to config host level
MatchPort® AR Embedded Device Server Command Reference 77 5: Commands and Levels
name Sets the name of the host. = name of the host. no name Clears the name of the host. no remote address Clears the remote address of the host. no ssh username Clears the SSH username associated with the host. protocol ssh Sets the protocol to SSH. protocol telnet Sets the protocol to Telnet. remote address Sets the IP address of the remote host to connect to when this host is selected on the login connect menu. = IP address. remote port Sets the remote port used to connect to the host. = port to be used. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. ssh username Sets the username for logging into the host via SSH. = username. write Stores the current configuration in permanent memory. host 12 (tunnel-connect-host:2:12) level commands address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout.
MatchPort® AR Embedded Device Server Command Reference 78 5: Commands and Levels
exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 12 (tunnel-connect-host:1:12) level commands address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains
MatchPort® AR Embedded Device Server Command Reference 79 5: Commands and Levels
spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections
MatchPort® AR Embedded Device Server Command Reference 80 5: Commands and Levels
with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 12 (config-host:12) level commands clrscrn Clears the screen. default protocol Restores the default value of the protocol (Telnet). default remote port Sets the remote port (used to connect to the host) to the default value, which depends on the selected protocol. exit Exits to the configuration level. host Change to config host level name Sets the name of the host. = name of the host. no name Clears the name of the host. no remote address Clears the remote address of the host. no ssh username Clears the SSH username associated with the host. protocol ssh Sets the protocol to SSH. protocol telnet Sets the protocol to Telnet. remote address Sets the IP address of the remote host to connect to when this host is selected on the login connect menu. = IP address. remote port Sets the remote port used to connect to the host. = port to be used. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. ssh username Sets the username for logging into the host via SSH. = username. write Stores the current configuration in permanent memory. host 13 (tunnel-connect-host:2:13) level commands address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces.
MatchPort® AR Embedded Device Server Command Reference 81 5: Commands and Levels
aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name.
MatchPort® AR Embedded Device Server Command Reference 82 5: Commands and Levels
tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 13 (tunnel-connect-host:1:13) level commands address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name.
MatchPort® AR Embedded Device Server Command Reference 83 5: Commands and Levels
no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 13 (config-host:13) level commands clrscrn Clears the screen. default protocol Restores the default value of the protocol (Telnet). default remote port Sets the remote port (used to connect to the host) to the default value, which depends on the selected protocol. exit Exits to the configuration level. host Change to config host level name Sets the name of the host. = name of the host. no name Clears the name of the host. no remote address Clears the remote address of the host. no ssh username Clears the SSH username associated with the host. protocol ssh Sets the protocol to SSH. protocol telnet Sets the protocol to Telnet. remote address Sets the IP address of the remote host to connect to when this host is
MatchPort® AR Embedded Device Server Command Reference 84 5: Commands and Levels
selected on the login connect menu. = IP address. remote port Sets the remote port used to connect to the host. = port to be used. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. ssh username Sets the username for logging into the host via SSH. = username. write Stores the current configuration in permanent memory. host 14 (tunnel-connect-host:2:14) level commands address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout.
MatchPort® AR Embedded Device Server Command Reference 85 5: Commands and Levels
no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 14 (tunnel-connect-host:1:14) level commands address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc-
MatchPort® AR Embedded Device Server Command Reference 86 5: Commands and Levels
tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address.
MatchPort® AR Embedded Device Server Command Reference 87 5: Commands and Levels
vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 14 (config-host:14) level commands clrscrn Clears the screen. default protocol Restores the default value of the protocol (Telnet). default remote port Sets the remote port (used to connect to the host) to the default value, which depends on the selected protocol. exit Exits to the configuration level. host Change to config host level name Sets the name of the host. = name of the host. no name Clears the name of the host. no remote address Clears the remote address of the host. no ssh username Clears the SSH username associated with the host. protocol ssh Sets the protocol to SSH. protocol telnet Sets the protocol to Telnet. remote address Sets the IP address of the remote host to connect to when this host is selected on the login connect menu. = IP address. remote port Sets the remote port used to connect to the host. = port to be used. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. ssh username Sets the username for logging into the host via SSH. = username. write Stores the current configuration in permanent memory. host 15 (tunnel-connect-host:2:15) level commands address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc
MatchPort® AR Embedded Device Server Command Reference 88 5: Commands and Levels
Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name.
MatchPort® AR Embedded Device Server Command Reference 89 5: Commands and Levels
vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 15 (tunnel-connect-host:1:15) level commands address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode
MatchPort® AR Embedded Device Server Command Reference 90 5: Commands and Levels
tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 15 (config-host:15) level commands clrscrn Clears the screen. default protocol Restores the default value of the protocol (Telnet). default remote port Sets the remote port (used to connect to the host) to the default value, which depends on the selected protocol. exit Exits to the configuration level. host Change to config host level name Sets the name of the host. = name of the host. no name Clears the name of the host. no remote address Clears the remote address of the host. no ssh username Clears the SSH username associated with the host. protocol ssh Sets the protocol to SSH. protocol telnet Sets the protocol to Telnet. remote address Sets the IP address of the remote host to connect to when this host is selected on the login connect menu. = IP address. remote port Sets the remote port used to connect to the host. = port to be used. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. ssh username Sets the username for logging into the host via SSH. = username.
MatchPort® AR Embedded Device Server Command Reference 91 5: Commands and Levels
write Stores the current configuration in permanent memory. host 16 (tunnel-connect-host:2:16) level commands address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling.
MatchPort® AR Embedded Device Server Command Reference 92 5: Commands and Levels
protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 16 (tunnel-connect-host:1:16) level commands address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics
MatchPort® AR Embedded Device Server Command Reference 93 5: Commands and Levels
clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 16 (config-host:16) level commands clrscrn Clears the screen. default protocol Restores the default value of the protocol (Telnet). default remote port Sets the remote port (used to connect to the host) to the default value,
MatchPort® AR Embedded Device Server Command Reference 94 5: Commands and Levels
which depends on the selected protocol. exit Exits to the configuration level. host Change to config host level name Sets the name of the host. = name of the host. no name Clears the name of the host. no remote address Clears the remote address of the host. no ssh username Clears the SSH username associated with the host. protocol ssh Sets the protocol to SSH. protocol telnet Sets the protocol to Telnet. remote address Sets the IP address of the remote host to connect to when this host is selected on the login connect menu. = IP address. remote port Sets the remote port used to connect to the host. = port to be used. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. ssh username Sets the username for logging into the host via SSH. = username. write Stores the current configuration in permanent memory. host 2 (tunnel-connect-host:2:2) level commands address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen.
MatchPort® AR Embedded Device Server Command Reference 95 5: Commands and Levels
default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 2 (tunnel-connect-host:1:2) level commands address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits.
MatchPort® AR Embedded Device Server Command Reference 96 5: Commands and Levels
Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session.
MatchPort® AR Embedded Device Server Command Reference 97 5: Commands and Levels
show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 2 (config-host:2) level commands clrscrn Clears the screen. default protocol Restores the default value of the protocol (Telnet). default remote port Sets the remote port (used to connect to the host) to the default value, which depends on the selected protocol. exit Exits to the configuration level. host Change to config host level name Sets the name of the host. = name of the host. no name Clears the name of the host. no remote address Clears the remote address of the host. no ssh username Clears the SSH username associated with the host. protocol ssh Sets the protocol to SSH. protocol telnet Sets the protocol to Telnet. remote address Sets the IP address of the remote host to connect to when this host is selected on the login connect menu. = IP address. remote port Sets the remote port used to connect to the host. = port to be used. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. ssh username Sets the username for logging into the host via SSH. = username. write Stores the current configuration in permanent memory. host 3 (tunnel-connect-host:2:3) level commands address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation:
MatchPort® AR Embedded Device Server Command Reference 98 5: Commands and Levels
123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics
MatchPort® AR Embedded Device Server Command Reference 99 5: Commands and Levels
ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 3 (tunnel-connect-host:1:3) level commands address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key.
MatchPort® AR Embedded Device Server Command Reference 100 5: Commands and Levels
no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 3 (config-host:3) level commands clrscrn Clears the screen. default protocol Restores the default value of the protocol (Telnet). default remote port Sets the remote port (used to connect to the host) to the default value, which depends on the selected protocol. exit Exits to the configuration level. host Change to config host level name Sets the name of the host. = name of the host. no name Clears the name of the host. no remote address Clears the remote address of the host. no ssh username Clears the SSH username associated with the host.
MatchPort® AR Embedded Device Server Command Reference 101 5: Commands and Levels
protocol ssh Sets the protocol to SSH. protocol telnet Sets the protocol to Telnet. remote address Sets the IP address of the remote host to connect to when this host is selected on the login connect menu. = IP address. remote port Sets the remote port used to connect to the host. = port to be used. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. ssh username Sets the username for logging into the host via SSH. = username. write Stores the current configuration in permanent memory. host 4 (tunnel-connect-host:2:4) level commands address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key.
MatchPort® AR Embedded Device Server Command Reference 102 5: Commands and Levels
no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 4 (tunnel-connect-host:1:4) level commands address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces.
MatchPort® AR Embedded Device Server Command Reference 103 5: Commands and Levels
aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect-
MatchPort® AR Embedded Device Server Command Reference 104 5: Commands and Levels
ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 4 (config-host:4) level commands clrscrn Clears the screen. default protocol Restores the default value of the protocol (Telnet). default remote port Sets the remote port (used to connect to the host) to the default value, which depends on the selected protocol. exit Exits to the configuration level. host Change to config host level name Sets the name of the host. = name of the host. no name Clears the name of the host. no remote address Clears the remote address of the host. no ssh username Clears the SSH username associated with the host. protocol ssh Sets the protocol to SSH. protocol telnet Sets the protocol to Telnet. remote address Sets the IP address of the remote host to connect to when this host is selected on the login connect menu. = IP address. remote port Sets the remote port used to connect to the host. = port to be used. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. ssh username Sets the username for logging into the host via SSH. = username. write Stores the current configuration in permanent memory. host 5 (tunnel-connect-host:2:5) level commands address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16
MatchPort® AR Embedded Device Server Command Reference 105 5: Commands and Levels
bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing.
MatchPort® AR Embedded Device Server Command Reference 106 5: Commands and Levels
validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 5 (tunnel-connect-host:1:5) level commands address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use.
MatchPort® AR Embedded Device Server Command Reference 107 5: Commands and Levels
protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 5 (config-host:5) level commands clrscrn Clears the screen. default protocol Restores the default value of the protocol (Telnet). default remote port Sets the remote port (used to connect to the host) to the default value, which depends on the selected protocol. exit Exits to the configuration level. host Change to config host level name Sets the name of the host. = name of the host. no name Clears the name of the host. no remote address Clears the remote address of the host. no ssh username Clears the SSH username associated with the host. protocol ssh Sets the protocol to SSH. protocol telnet Sets the protocol to Telnet. remote address Sets the IP address of the remote host to connect to when this host is selected on the login connect menu. = IP address. remote port Sets the remote port used to connect to the host. = port to be used.
MatchPort® AR Embedded Device Server Command Reference 108 5: Commands and Levels
show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. ssh username Sets the username for logging into the host via SSH. = username. write Stores the current configuration in permanent memory. host 6 (tunnel-connect-host:2:6) level commands address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling.
MatchPort® AR Embedded Device Server Command Reference 109 5: Commands and Levels
protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 6 (tunnel-connect-host:1:6) level commands address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16
MatchPort® AR Embedded Device Server Command Reference 110 5: Commands and Levels
bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory.
MatchPort® AR Embedded Device Server Command Reference 111 5: Commands and Levels
host 6 (config-host:6) level commands clrscrn Clears the screen. default protocol Restores the default value of the protocol (Telnet). default remote port Sets the remote port (used to connect to the host) to the default value, which depends on the selected protocol. exit Exits to the configuration level. host Change to config host level name Sets the name of the host. = name of the host. no name Clears the name of the host. no remote address Clears the remote address of the host. no ssh username Clears the SSH username associated with the host. protocol ssh Sets the protocol to SSH. protocol telnet Sets the protocol to Telnet. remote address Sets the IP address of the remote host to connect to when this host is selected on the login connect menu. = IP address. remote port Sets the remote port used to connect to the host. = port to be used. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. ssh username Sets the username for logging into the host via SSH. = username. write Stores the current configuration in permanent memory. host 7 (tunnel-connect-host:2:7) level commands address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes.
MatchPort® AR Embedded Device Server Command Reference 112 5: Commands and Levels
Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 7 (tunnel-connect-host:1:7) level commands
MatchPort® AR Embedded Device Server Command Reference 113 5: Commands and Levels
address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling.
MatchPort® AR Embedded Device Server Command Reference 114 5: Commands and Levels
protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 7 (config-host:7) level commands clrscrn Clears the screen. default protocol Restores the default value of the protocol (Telnet). default remote port Sets the remote port (used to connect to the host) to the default value, which depends on the selected protocol. exit Exits to the configuration level. host Change to config host level name Sets the name of the host. = name of the host. no name Clears the name of the host. no remote address Clears the remote address of the host. no ssh username Clears the SSH username associated with the host. protocol ssh Sets the protocol to SSH. protocol telnet Sets the protocol to Telnet. remote address Sets the IP address of the remote host to connect to when this host is selected on the login connect menu. = IP address. remote port Sets the remote port used to connect to the host. = port to be used. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. ssh username Sets the username for logging into the host via SSH. = username. write Stores the current configuration in permanent memory. host 8 (tunnel-connect-host:2:8) level commands address Sets the remote host to establish tunneling connections with.
MatchPort® AR Embedded Device Server Command Reference 115 5: Commands and Levels
= IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode
MatchPort® AR Embedded Device Server Command Reference 116 5: Commands and Levels
tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 8 (tunnel-connect-host:1:8) level commands address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep
MatchPort® AR Embedded Device Server Command Reference 117 5: Commands and Levels
alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 8 (config-host:8) level commands clrscrn Clears the screen. default protocol Restores the default value of the protocol (Telnet). default remote port Sets the remote port (used to connect to the host) to the default value, which depends on the selected protocol. exit Exits to the configuration level. host Change to config host level
MatchPort® AR Embedded Device Server Command Reference 118 5: Commands and Levels
name Sets the name of the host. = name of the host. no name Clears the name of the host. no remote address Clears the remote address of the host. no ssh username Clears the SSH username associated with the host. protocol ssh Sets the protocol to SSH. protocol telnet Sets the protocol to Telnet. remote address Sets the IP address of the remote host to connect to when this host is selected on the login connect menu. = IP address. remote port Sets the remote port used to connect to the host. = port to be used. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. ssh username Sets the username for logging into the host via SSH. = username. write Stores the current configuration in permanent memory. host 9 (tunnel-connect-host:2:9) level commands address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout.
MatchPort® AR Embedded Device Server Command Reference 119 5: Commands and Levels
exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 9 (tunnel-connect-host:1:9) level commands address Sets the remote host to establish tunneling connections with. = IP address or host name of the remote host. aes decrypt key Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains
MatchPort® AR Embedded Device Server Command Reference 120 5: Commands and Levels
spaces. aes decrypt key text Sets the connect tunnel AES decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. aes encrypt key Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123ABC "12 3A BC" 12,3A,BC 12.3a.bc 12:3a:bc Note that quotes must enclose the value if it contains spaces. aes encrypt key text Sets the connect tunnel AES encrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. auto show statistics show connection statistics clrscrn Clears the screen. default protocol Restores the default protocol as "TCP". default tcp keep alive Restores the default 45 second connect mode TCP keep alive timeout. exit Exits to the next higher level. no address Removes the remote host address used to establish tun- neling connections. no aes decrypt key Removes the connect tunnel AES decrypt key. no aes encrypt key Removes the connect tunnel AES encrypt key. no port Removes the remote port used to establish tunnel con- nections. no ssh username Removes the SSH user name. no tcp keep alive Disables the connect mode TCP keep alive timeout. no vip name Removes the VIP name. port Sets the remote port to use for connect mode tunneling. = number of the port to use. protocol ssh Uses SSH protocol for connect mode tunneling. protocol ssl Uses SSL protocol for connect mode tunneling. protocol tcp Uses TCP protocol for connect mode tunneling. protocol tcp aes Uses TCP protocol with AES encryption for connect mode tunneling. protocol telnet Uses Telnet protocol (with IAC) for connect mode tunnel- ing. protocol udp Uses UDP protocol for connect mode tunneling. protocol udp aes Uses UDP protocol with AES encryption for connect mode tunneling. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics ssh username Sets the SSH user name for use when establishing tun- neling connections
MatchPort® AR Embedded Device Server Command Reference 121 5: Commands and Levels
with other devices. = SSH user name. tcp keep alive Enables TCP keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. validate certificate disable Skips verification of the server certificate when connect- ing. validate certificate enable Requires verification of the server certificate when con- necting. vip disable Makes connections using the specified Address. vip enable Makes connections using the VIP name. vip name Sets the VIP name. write Stores the current configuration in permanent memory. host 9 (config-host:9) level commands clrscrn Clears the screen. default protocol Restores the default value of the protocol (Telnet). default remote port Sets the remote port (used to connect to the host) to the default value, which depends on the selected protocol. exit Exits to the configuration level. host Change to config host level name Sets the name of the host. = name of the host. no name Clears the name of the host. no remote address Clears the remote address of the host. no ssh username Clears the SSH username associated with the host. protocol ssh Sets the protocol to SSH. protocol telnet Sets the protocol to Telnet. remote address Sets the IP address of the remote host to connect to when this host is selected on the login connect menu. = IP address. remote port Sets the remote port used to connect to the host. = port to be used. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. ssh username Sets the username for logging into the host via SSH. = username. write Stores the current configuration in permanent memory. http (config-http) level commands auth Creates a new HTTP server authentication directive. = URI of the server. = domain of the server. auth type basic Sets an HTTP server authentication directive to the Basic Access Authentication scheme. = URI of the server. auth type digest Sets an HTTP server authentication directive to the Digest Access Authentication scheme. = URI of the server.
MatchPort® AR Embedded Device Server Command Reference 122 5: Commands and Levels
auth type none Sets the authentication type for an HTTP server authenti- cation directive to none. = URI of the server. auth type ssl Sets the authentication type for an HTTP server authenti- cation directive to SSL. = URI of the server. auth type ssl-basic Sets the authentication type for an HTTP server authenti- cation directive to SSL-Basic. = URI of the server. auth type ssl-digest Sets the authentication type for an HTTP server authenti- cation directive to SSL-Digest. = URI of the server. auth user Creates or modifies a user for an HTTP server authentica- tion directive. = URI of the server. = username. = password associated with the username. authentication timeout For any Digest AuthType, sets the timeout for authentica- tion. = authentication timeout value. clear counters Sets the HTTP counters to zero. clear log Clears the HTTP server log. clrscrn Clears the screen. default authentication timeout Resets the authentication timeout to its default value. default log format Restores the HTTP Server log format string to its default value. default max bytes Resets the maximum bytes to its default value. default max log entries Restores the default maximum number of HTTP Server log entries. default max timeout Resets the timeout to its default value. default port Resets the HTTP Server port to its default value. default secure port Resets the HTTP Server SSL port to its default value. default secure protocols Restores the default secure protocol selections. delete auth Deletes an existing HTTP Server authentication directive. = URI of the server. delete auth user Deletes an existing user for an HTTP Server authentica- tion directive. = URI of the server. = username. exit Returns to the config level. log format Sets the log format string for the HTTP server, using the following directives: %a remote ip address (could be a proxy) %b bytes sent excluding headers %B bytes sent excluding headers (0 = '-') %h remote host (same as %a) %{h}i header contents from request (h = header string) %m request method %p ephemeral local port value used for request %q query string (prepend with '?' or empty '-') %t timestamp HH:MM:SS (same as Apache
MatchPort® AR Embedded Device Server Command Reference 123 5: Commands and Levels
'%(%H:%M:%S)t') %u remote user (could be bogus for 401 status) %U URL path info %r first line of request (same as '%m %U%q ') %s return status logging state disable Disables HTTP server logging. logging state enable Enables HTTP server logging. max bytes Sets the maximum number of bytes the HTTP server ac- cepts when receiving a request. max log entries Sets the maximum number of HTTP server log entries. = maximum number of HTTP server log en- tries. max timeout Sets the maximum time the HTTP server waits when re- ceiving a request. = maximum timeout value. no clear counters Restores the HTTP counters to the aggregate values. no port Disables the HTTP Server port. no secure port Disables the HTTP Server SSL port. port Sets the port number the HTTP server will use. = port number. secure port Sets the port number the HTTP server will use over SSL. = port number. secure protocols ssl3 disable Disables the protocol. secure protocols ssl3 enable Enables the protocol. secure protocols tls1.0 disable Disables the protocol. secure protocols tls1.0 enable Enables the protocol. secure protocols tls1.1 disable Disables the protocol. secure protocols tls1.1 enable Enables the protocol. show Displays the current configuration. show auth Displays the HTTP server authentication settings. show history Displays the last 20 commands entered during the current CLI session. show log Displays the HTTP server log. show statistics Displays the HTTP statistics. state disable Disables the HTTP server. state enable Enables the HTTP server. write Stores the current configuration in permanent memory. icmp (config-icmp) level commands auto show statistics Continuously shows ICMP statistics clear counters Zeros counters clrscrn Clears the screen. exit Exits to the configuration level. no clear counters Unzeros IP counters show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics Shows ICMP statistics state disable Prevents ICMP packets from being sent or received.
MatchPort® AR Embedded Device Server Command Reference 124 5: Commands and Levels
state enable Allows ICMP packets to be sent and received. write Stores the current configuration in permanent memory. if 1 (config-if:eth0) level commands bootp disable Disables BOOTP. bootp enable Enables BOOTP. clrscrn Clears the screen. default gateway Sets the configurable gateway IP address to the default value. default mtu Restores the default Maximum Transmission Unit (MTU) size. dhcp client id binary Sets the client id allowing binary characters. Within [] use binary decimal up to 255 or hex up to 0xFF. dhcp client id set Sets the client id in text format. dhcp disable Disables DHCP. dhcp enable Enables DHCP. dhcp renew Force DHCP to renew domain Sets the domain name. = name of the domain. exit Exits to the config level. hostname Sets the host name. = name of the host. ip address Sets the IP address and network mask. Formats accepted: 192.168.1.1 (default mask) 192.168.1.1/24 (CIDR) "192.168.1.1 255.255.255.0" (explicit mask) link Enter link configuration level mtu Sets the Maximum Transmission Unit (MTU) size. no default gateway Clears the default gateway. no dhcp client id Clears the DHCP client ID. no domain Clears the domain name. no hostname Clears the host name. no ip address Clears the IP address. no primary dns Clears the name of the primary DNS server. no secondary dns Clears the name of the secondary DNS server. primary dns Sets the IP address of the primary DNS server. secondary dns Sets the IP address of the secondary DNS server. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. show status Show interface status write Stores the current configuration in permanent memory. ip (config-ip) level commands auto show statistics Continuously shows IP statistics clear counters Zeros counters clrscrn Clears the screen. default ip time to live Restores the default IP time to live. default multicast time to live Restores the default IP multicast time to live, which is one hop.
MatchPort® AR Embedded Device Server Command Reference 125 5: Commands and Levels
exit Exits to the configuration level. ip time to live Sets the IP time to live, known by SNMP as "ipDefaultTTL". = number of hops that a typical IP packet is al- lowed to live. multicast time to live Sets the IP multicast time to live. = number of hops that a multicast IP packet is allowed to live. no clear counters Unzeros IP counters show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics Shows IP statistics write Stores the current configuration in permanent memory. ip filter (config-filter) level commands add Adds an entry to the IP filter table. clrscrn Clears the screen. exit Returns to the config level. no filtering Removes filtering so ALL addresses are allowed. remove Removes an entry from the IP filter table. show Displays the IP filter table. show history Displays the last 20 commands entered during the current CLI session. write Stores the current configuration in permanent memory. line 1 (line:1) level commands auto show statistics Continuously displays line statistics. baud rate Sets the line speed. = the speed. Standard speeds include 1200, 2400, 4800, 9600, 19200, and so on. clear line counters Sets the serial counters to zero. clrscrn Clears the screen. command mode always Sets the current line to always be in command mode. command mode cp Sets the current line to enter command mode under con- trol of a CP. command mode cp Specifies the CP group and trigger value. command mode echo serial string disable Disables user-defined serial boot string to be echoed in the CLI. command mode echo serial string enable Enables user-defined serial boot string to be echoed in the CLI. command mode serial string Enables user to enter a custom string at boot time to enter command mode. command mode serial string Sets a string that can be entered at boot time to enter command mode. = text. command mode serial string binary Sets a binary string that can be entered at boot time to enter command mode. = string that may contain binary characters. Within [] use binary decimal up to 255 or hex up to 0xFF. command mode signon message Sets an ASCII sign-on message that is sent from the seri- al port when the
MatchPort® AR Embedded Device Server Command Reference 126 5: Commands and Levels
device boots and when the line is in command mode. = text. command mode signon message binary Sets a binary sign-on message that is sent from the serial port when the device boots and when the line is in command mode. = string that may contain binary characters. Within [] use binary decimal up to 255 or hex up to 0xFF. command mode wait time Sets boot-up wait time for command mode serial string. = wait time. configure current settings Configures line with the current value of settings. data bits 7 Uses seven bits for data on the line. data bits 8 Uses eight bits for data on the line. default baud rate Restores the default speed of 9600 bits per second. default data bits Restores the default of eight data bits. default flow control Restores the default of no flow control. default interface Restores the default interface type to this line. default parity Restores the default of no parity. default protocol Restores the default protocol on the line. default stop bits Restores the default of one stop bit. default threshold Restores the factory default threshold. default xoff char Restores the default xoff character on this line. default xon char Restores the default xon character on this line. exit Exits to the enable level flow control hardware Uses hardware (RTS/CTS) flow control on the line. flow control none Does not provide flow control on the line. flow control software Uses software (xon/xoff characters) flow control on the line. gap timer Sets the gap timer in milliseconds. If some data has been received, it will be forwarded after this time since the last character. interface rs232 Sets the line interface to RS232. interface rs485 full-duplex Sets the line interface to RS485 in full-duplex mode. interface rs485 half-duplex Sets the line interface to RS485 in half-duplex mode. kill session Kills command mode session on the Line line Enters the line level. = number of the line (serial port) to be configured. lpd Enters the configure lpd level. = number of the line (lpd serial port) to be config- ured. name Sets the name for this line. no clear line counters Restores the serial counters to the aggregate values. no command mode Disables command mode for the current line. no command mode cp Disables control of a CP to enter command mode. no command mode serial string Prevents the user-defined serial boot string from being used to enter command mode in the CLI. no command mode signon message Clears the signon message displayed at boot time and when entering command mode. no gap timer Removes the gap timer, so forwarding depends on the
MatchPort® AR Embedded Device Server Command Reference 127 5: Commands and Levels
line speed. no name Removes the name of this line. parity even Uses a parity bit on the line for even parity. parity none Does not use a parity bit on the line. parity odd Uses a parity bit on the line for odd parity. ppp Enters the serial line PPP level. protocol lpd Applies Line Printer Daemon (LPD) protocol on the line. protocol lpd or tunnel Applies LPD or tunnel protocol on the line. protocol modbus ascii Applies Modbus ASCII protocol on the line. protocol modbus rtu Applies Modbus RTU protocol on the line. protocol none Uses no protocol on the line. protocol ppp Applies point-to-point protocol (PPP) on the line. protocol tunnel Applies tunnel protocol on the line. reassert Asserts line status with current configured values. show Displays the current status. show command mode Shows the command mode settings for the current line. show history Displays the last 20 commands entered during the current CLI session. show line Displays the current configuration. show statistics Shows the line statistics. state disable Disables the line so data cannot be sent/received. state enable Enables the line so data can be sent/received. stop bits 1 Uses one stop bit after data on the line. stop bits 2 Uses two stop bits after data on the line. terminal Enters the configure-terminal level. = number of the terminal line (serial port) to be con- figured. terminal network Enters the configure-terminal level for the network. threshold Sets the threshold in bytes. After this many bytes are re- ceived, they are forwarded without delay. tunnel Enters the tunnel level. = number of the tunnel line (serial port) to be con- figured. write Stores the current configuration in permanent memory. xoff char Sets the xoff character for use with software flow control on this line. The character may be input as text, control, decimal, or hex. A control character has the form C. A decimal value character has the form \99. A hex value character has the form 0xFF. xon char Sets the xon character for use with software flow control on this line. The character may be input as text, control, decimal, or hex. A control character has the form C. A decimal value character has the form \99. A hex value character has the form 0xFF. line 2 (line:2) level commands auto show statistics Continuously displays line statistics.
MatchPort® AR Embedded Device Server Command Reference 128 5: Commands and Levels
baud rate Sets the line speed. = the speed. Standard speeds include 1200, 2400, 4800, 9600, 19200, and so on. clear line counters Sets the serial counters to zero. clrscrn Clears the screen. command mode always Sets the current line to always be in command mode. command mode cp Sets the current line to enter command mode under con- trol of a CP. command mode cp Specifies the CP group and trigger value. command mode echo serial string disable Disables user-defined serial boot string to be echoed in the CLI. command mode echo serial string enable Enables user-defined serial boot string to be echoed in the CLI. command mode serial string Enables user to enter a custom string at boot time to enter command mode. command mode serial string Sets a string that can be entered at boot time to enter command mode. = text. command mode serial string binary Sets a binary string that can be entered at boot time to enter command mode. = string that may contain binary characters. Within [] use binary decimal up to 255 or hex up to 0xFF. command mode signon message Sets an ASCII sign-on message that is sent from the seri- al port when the device boots and when the line is in command mode. = text. command mode signon message binary Sets a binary sign-on message that is sent from the serial port when the device boots and when the line is in command mode. = string that may contain binary characters. Within [] use binary decimal up to 255 or hex up to 0xFF. command mode wait time Sets boot-up wait time for command mode serial string. = wait time. configure current settings Configures line with the current value of settings. data bits 7 Uses seven bits for data on the line. data bits 8 Uses eight bits for data on the line. default baud rate Restores the default speed of 9600 bits per second. default data bits Restores the default of eight data bits. default flow control Restores the default of no flow control. default interface Restores the default interface type to this line. default parity Restores the default of no parity. default protocol Restores the default protocol on the line. default stop bits Restores the default of one stop bit. default threshold Restores the factory default threshold. default xoff char Restores the default xoff character on this line. default xon char Restores the default xon character on this line. exit Exits to the enable level flow control hardware Uses hardware (RTS/CTS) flow control on the line. flow control none Does not provide flow control on the line. flow control software Uses software (xon/xoff characters) flow control on the
MatchPort® AR Embedded Device Server Command Reference 129 5: Commands and Levels
line. gap timer Sets the gap timer in milliseconds. If some data has been received, it will be forwarded after this time since the last character. interface rs232 Sets the line interface to RS232. interface rs485 full-duplex Sets the line interface to RS485 in full-duplex mode. interface rs485 half-duplex Sets the line interface to RS485 in half-duplex mode. kill session Kills command mode session on the Line line Enters the line level. = number of the line (serial port) to be configured. lpd Enters the configure lpd level. = number of the line (lpd serial port) to be config- ured. name Sets the name for this line. no clear line counters Restores the serial counters to the aggregate values. no command mode Disables command mode for the current line. no command mode cp Disables control of a CP to enter command mode. no command mode serial string Prevents the user-defined serial boot string from being used to enter command mode in the CLI. no command mode signon message Clears the signon message displayed at boot time and when entering command mode. no gap timer Removes the gap timer, so forwarding depends on the line speed. no name Removes the name of this line. parity even Uses a parity bit on the line for even parity. parity none Does not use a parity bit on the line. parity odd Uses a parity bit on the line for odd parity. ppp Enters the serial line PPP level. protocol lpd Applies Line Printer Daemon (LPD) protocol on the line. protocol lpd or tunnel Applies LPD or tunnel protocol on the line. protocol modbus ascii Applies Modbus ASCII protocol on the line. protocol modbus rtu Applies Modbus RTU protocol on the line. protocol none Uses no protocol on the line. protocol ppp Applies point-to-point protocol (PPP) on the line. protocol tunnel Applies tunnel protocol on the line. reassert Asserts line status with current configured values. show Displays the current status. show command mode Shows the command mode settings for the current line. show history Displays the last 20 commands entered during the current CLI session. show line Displays the current configuration. show statistics Shows the line statistics. state disable Disables the line so data cannot be sent/received. state enable Enables the line so data can be sent/received. stop bits 1 Uses one stop bit after data on the line. stop bits 2 Uses two stop bits after data on the line. terminal Enters the configure-terminal level.
MatchPort® AR Embedded Device Server Command Reference 130 5: Commands and Levels
= number of the terminal line (serial port) to be con- figured. terminal network Enters the configure-terminal level for the network. threshold Sets the threshold in bytes. After this many bytes are re- ceived, they are forwarded without delay. tunnel Enters the tunnel level. = number of the tunnel line (serial port) to be con- figured. write Stores the current configuration in permanent memory. xoff char Sets the xoff character for use with software flow control on this line. The character may be input as text, control, decimal, or hex. A control character has the form C. A decimal value character has the form \99. A hex value character has the form 0xFF. xon char Sets the xon character for use with software flow control on this line. The character may be input as text, control, decimal, or hex. A control character has the form C. A decimal value character has the form \99. A hex value character has the form 0xFF. link (config-ethernet:eth0) level commands clrscrn Clears the screen. default duplex Restores the default duplex setting, which is auto. default speed Restores the default speed setting, which is auto- negotiate. duplex auto Sets duplex mode to auto. duplex full Sets duplex mode to full. duplex half Sets duplex mode to half. exit Exit back to interface configuration level show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. speed 10 Sets the speed of the Ethernet link to 10 Mbps. speed 100 Sets the speed of the Ethernet link to 100 Mbps. speed auto Sets the speed of the Ethernet link to auto-negotiate. write Stores the current configuration in permanent memory. log (config-diagnostics-log) level commands clrscrn Clears the screen. default max length Restores the factory default maximum Log file size. default output Disables log output. default severity level Log all events. exit Exits to the next higher level. max length Sets the maximum size in Kbytes for the Log file. output disable Enables log to filesystem. output filesystem Enables log to serial line. output line Could not find VarID 438 entry 3 in file http/config/varid_help.mtxt
MatchPort® AR Embedded Device Server Command Reference 131 5: Commands and Levels
severity level debug Log all events. severity level error Log only Error and more severe events. severity level information Log only Information and more severe events. severity level notice Log only Notice and more severe events. severity level warning Log only Warning and more severe events. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. write Stores the current configuration in permanent memory. lpd (lpd) level commands auto show Continuously displays lpd status for the specified line. = LPD line to display. clrscrn Clears the screen. exit Exits to the enable level. kill Kills the current print job on the specified line. = LPD line with print job. show Displays lpd status for the specified line. = LPD line to display. show history Displays the last 20 commands entered during the current CLI session. write Stores the current configuration in permanent memory. lpd 1 (config-lpd:1) level commands banner disable Disables printing banner for all print jobs. Only print the banner when a job requests it. banner enable Enables printing banner for all print jobs. binary disable Treats print job as ascii text. Filters out all non-ascii char- acters and certain control characters. binary enable Treats print job as binary. Sends data byte-for-byte to the printer. capture disable Redirects serial output back to the line. capture enable Redirects serial output from the line to this CLI session. clrscrn Clears the screen. convert newline disable Disables converting single new line and carriage return characters to DOS-style line endings. convert newline enable Enables converting single new line and carriage return characters to DOS-style line endings. If characters are already in DOS line-ending order, they are not converted. eoj disable Disables sending the end-of-job string after each print job. eoj enable Enables sending the end-of-job string after each print job. eoj text binary Sets the end-of-job text allowing for binary characters. = string in binary format that will be sent to the printer at the end of each print job. Within [] use binary decimal up to 255 or hex up to 0xFF. eoj text set Sets the end-of-job text. = ascii string that will be sent to the printer at the end of each
MatchPort® AR Embedded Device Server Command Reference 132 5: Commands and Levels
print job. exit Exits to the configuration level. formfeed disable Disables the printer from advancing to the next page at the end of each print job. formfeed enable Forces the printer to advance to the next page at the end of each print job. kill Ends the current print job on this lpd line. line Enters the line level. = number of the line (serial port) to be configured. lpd Enters the configure lpd level. = number of the line (lpd serial port) to be config- ured. no eoj text Removes the end-of-job string. no queue name Removes the queue name. no soj text Removes the start-of-job string. ppp Enters the serial line PPP level. queue name Sets the name of the queue that this lpd line belongs to. = name for the queue. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics Displays statistics and status information for this lpd line. soj disable Disables sending the start-of-job string after each print job. soj enable Enables sending the start-of-job string after each print job. soj text binary Sets the start-of-job text allowing for binary characters. = string in binary format that will be sent to the printer at the beginning of each print job. Within [] use binary decimal up to 255 or hex up to 0xFF. soj text set Sets the start-of-job text. = ascii string that will be sent to the printer at the beginning of each print job. terminal Enters the configure-terminal level. = number of the terminal line (serial port) to be con- figured. terminal network Enters the configure-terminal level for the network. test print Prints lines of text directly to the lpd line. = number of lines to print. tunnel Enters the tunnel level. = number of the tunnel line (serial port) to be con- figured. write Stores the current configuration in permanent memory. lpd 2 (config-lpd:2) level commands banner disable Disables printing banner for all print jobs. Only print the banner when a job requests it. banner enable Enables printing banner for all print jobs. binary disable Treats print job as ascii text. Filters out all non-ascii char- acters and
MatchPort® AR Embedded Device Server Command Reference 133 5: Commands and Levels
certain control characters. binary enable Treats print job as binary. Sends data byte-for-byte to the printer. capture disable Redirects serial output back to the line. capture enable Redirects serial output from the line to this CLI session. clrscrn Clears the screen. convert newline disable Disables converting single new line and carriage return characters to DOS-style line endings. convert newline enable Enables converting single new line and carriage return characters to DOS-style line endings. If characters are already in DOS line-ending order, they are not converted. eoj disable Disables sending the end-of-job string after each print job. eoj enable Enables sending the end-of-job string after each print job. eoj text binary Sets the end-of-job text allowing for binary characters. = string in binary format that will be sent to the printer at the end of each print job. Within [] use binary decimal up to 255 or hex up to 0xFF. eoj text set Sets the end-of-job text. = ascii string that will be sent to the printer at the end of each print job. exit Exits to the configuration level. formfeed disable Disables the printer from advancing to the next page at the end of each print job. formfeed enable Forces the printer to advance to the next page at the end of each print job. kill Ends the current print job on this lpd line. line Enters the line level. = number of the line (serial port) to be configured. lpd Enters the configure lpd level. = number of the line (lpd serial port) to be config- ured. no eoj text Removes the end-of-job string. no queue name Removes the queue name. no soj text Removes the start-of-job string. ppp Enters the serial line PPP level. queue name Sets the name of the queue that this lpd line belongs to. = name for the queue. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics Displays statistics and status information for this lpd line. soj disable Disables sending the start-of-job string after each print job. soj enable Enables sending the start-of-job string after each print job. soj text binary Sets the start-of-job text allowing for binary characters. = string in binary format that will be sent to the
MatchPort® AR Embedded Device Server Command Reference 134 5: Commands and Levels
printer at the beginning of each print job. Within [] use binary decimal up to 255 or hex up to 0xFF. soj text set Sets the start-of-job text. = ascii string that will be sent to the printer at the beginning of each print job. terminal Enters the configure-terminal level. = number of the terminal line (serial port) to be con- figured. terminal network Enters the configure-terminal level for the network. test print Prints lines of text directly to the lpd line. = number of lines to print. tunnel Enters the tunnel level. = number of the tunnel line (serial port) to be con- figured. write Stores the current configuration in permanent memory. modbus (modbus) level commands additional port Sets an additional TCP server port. clrscrn Clears the screen. default response timeout Restores the default Modbus Response Timeout. exit Exits to the config level. kill connection Kills modbus connection selected by index from show connections. no additional port Removes the additional TCP server port. response timeout Sets the Modbus Response Timeout in milliseconds. rss Enters the next lower level. show Displays the current configuration. show connections Displays connections. show history Displays the last 20 commands entered during the current CLI session. show statistics Displays statistics. tcp server state disable Disables the Modbus TCP Server. tcp server state enable Enables the Modbus TCP Server. write Stores the current configuration in permanent memory. modem (tunnel-modem:2) level commands clrscrn Clears the screen. connect string Sets the CONNECT string used in modem emulation. = connect string. default incoming connection Default disables incoming network connections. default response type Default uses text type responses. display remote ip disable The incoming RING has nothing following it. display remote ip enable The incoming RING is followed by the IP address of the caller. echo commands disable Does not echo modem commands. echo commands enable Echoes modem commands. echo pluses disable Does not echo the +++ characters when entering modem command mode. echo pluses enable Echoes the +++ characters when entering modem com- mand mode.
MatchPort® AR Embedded Device Server Command Reference 135 5: Commands and Levels
error unknown commands disable Returns OK on unknown AT commands. error unknown commands enable Returns an error upon unknown AT commands. exit Returns to the tunnel level. incoming connection automatic Automatically answer incoming network connections. incoming connection disabled Disable incoming network connections. incoming connection manual Wait for an ATA command before answering an incoming network connection. no connect string Removes optional CONNECT string information for mo- dem emulation. reassert Asserts tunnel modem status with current configured val- ues. response type numeric Uses numeric type responses. response type text Uses text type responses. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. show status Displays tunnel modem status. verbose response disable Does not send Modem Response Codes. verbose response enable Sends Modem Response Codes out on the Serial Line. write Stores the current configuration in permanent memory. modem (tunnel-modem:1) level commands clrscrn Clears the screen. connect string Sets the CONNECT string used in modem emulation. = connect string. default incoming connection Default disables incoming network connections. default response type Default uses text type responses. display remote ip disable The incoming RING has nothing following it. display remote ip enable The incoming RING is followed by the IP address of the caller. echo commands disable Does not echo modem commands. echo commands enable Echoes modem commands. echo pluses disable Does not echo the +++ characters when entering modem command mode. echo pluses enable Echoes the +++ characters when entering modem com- mand mode. error unknown commands disable Returns OK on unknown AT commands. error unknown commands enable Returns an error upon unknown AT commands. exit Returns to the tunnel level. incoming connection automatic Automatically answer incoming network connections. incoming connection disabled Disable incoming network connections. incoming connection manual Wait for an ATA command before answering an incoming network connection. no connect string Removes optional CONNECT string information for mo- dem emulation. reassert Asserts tunnel modem status with current configured val- ues. response type numeric Uses numeric type responses. response type text Uses text type responses. show Displays the current configuration.
MatchPort® AR Embedded Device Server Command Reference 136 5: Commands and Levels
show history Displays the last 20 commands entered during the current CLI session. show status Displays tunnel modem status. verbose response disable Does not send Modem Response Codes. verbose response enable Sends Modem Response Codes out on the Serial Line. write Stores the current configuration in permanent memory. packing (tunnel-packing:2) level commands clrscrn Clears the screen. default packing mode Sets to default packing mode, which is "Disable" default send character Removes the send character for packing mode. default threshold Restores the default threshold. default timeout Restores the default packing mode timeout. exit Returns to the tunnel level. no trailing character Removes the trailing character for packing mode. packing mode disable Disables packing. Data is sent to the network when re- ceived. packing mode send character Sets packing mode to accumulate data and transmit it upon receiving the configured send character on the line (serial port). packing mode timeout Sets packing mode to accumulate data and transmit it after a specified amount of time (timeout). send character Sets the send character for packing mode. The character may be input as text, control, decimal, or hex. A control character has the form C. A decimal value character has the form \99. A hex value character has the form 0xFF. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. threshold Sets the threshold (byte count). If the queued data reach- es this threshold then the data will be sent. = number of bytes in the threshold. timeout Sets the timeout value for packing mode in milliseconds. = timeout value, in milliseconds. trailing character Sets the trailing character for packing mode. The character may be input as text, control, decimal, or hex. A control character has the form C. A decimal value character has the form \99. A hex value character has the form 0xFF. write Stores the current configuration in permanent memory. packing (tunnel-packing:1) level commands clrscrn Clears the screen. default packing mode Sets to default packing mode, which is "Disable" default send character Removes the send character for packing mode. default threshold Restores the default threshold. default timeout Restores the default packing mode timeout. exit Returns to the tunnel level.
MatchPort® AR Embedded Device Server Command Reference 137 5: Commands and Levels
no trailing character Removes the trailing character for packing mode. packing mode disable Disables packing. Data is sent to the network when re- ceived. packing mode send character Sets packing mode to accumulate data and transmit it upon receiving the configured send character on the line (serial port). packing mode timeout Sets packing mode to accumulate data and transmit it after a specified amount of time (timeout). send character Sets the send character for packing mode. The character may be input as text, control, decimal, or hex. A control character has the form C. A decimal value character has the form \99. A hex value character has the form 0xFF. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. threshold Sets the threshold (byte count). If the queued data reach- es this threshold then the data will be sent. = number of bytes in the threshold. timeout Sets the timeout value for packing mode in milliseconds. = timeout value, in milliseconds. trailing character Sets the trailing character for packing mode. The character may be input as text, control, decimal, or hex. A control character has the form C. A decimal value character has the form \99. A hex value character has the form 0xFF. write Stores the current configuration in permanent memory. password (tunnel-accept-password:2) level commands clrscrn Clears the screen. exit Exits to the next higher level. no password Removes the password so connections will be accepted unchallenged. password Sets the password required on the network side of the tunnel to begin a connection. prompt disable Inhibits any prompting for password on the network side of the tunnel. prompt enable Sets up so a user on the network side of the tunnel will be prompted for a password. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. write Stores the current configuration in permanent memory. password (tunnel-accept-password:1) level commands clrscrn Clears the screen. exit Exits to the next higher level. no password Removes the password so connections will be accepted unchallenged.
MatchPort® AR Embedded Device Server Command Reference 138 5: Commands and Levels
password Sets the password required on the network side of the tunnel to begin a connection. prompt disable Inhibits any prompting for password on the network side of the tunnel. prompt enable Sets up so a user on the network side of the tunnel will be prompted for a password. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. write Stores the current configuration in permanent memory. ppp 1 (ppp:1) level commands authentication mode chap Sets authentication to Challenge-Handshake Authentica- tion Protocol (CHAP). authentication mode ms-chap Sets authentication to MS-CHAP version 1. authentication mode ms-chapv2 Sets authentication to MS-CHAP version 2. authentication mode none Removes PPP authentication. authentication mode pap Sets authentication to Password Authentication Protocol (PAP). clrscrn Clears the screen. default authentication mode Removes PPP authentication. exit Exits to the configuration level. line Enters the line level. = number of the line (serial port) to be configured. local ip Sets the Local IP address and network mask. Formats accepted: 192.168.1.1 (default mask) 192.168.1.1/24 (CIDR) "192.168.1.1 255.255.255.0" (explicit mask) lpd Enters the configure lpd level. = number of the line (lpd serial port) to be config- ured. no local ip Removes the Local IP address. no password Removes the PPP authentication password. no peer ip Removes the peer IP address. no username Removes the PPP authentication username. password Sets the password for PPP authentication. peer ip Sets the IP Address assigned to the peer when requested during negotiation. IP address of the peer device. ppp Enters the serial line PPP level. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. terminal Enters the configure-terminal level. = number of the terminal line (serial port) to be con- figured. terminal network Enters the configure-terminal level for the network. tunnel Enters the tunnel level. = number of the tunnel line (serial port) to be con- figured.
MatchPort® AR Embedded Device Server Command Reference 139 5: Commands and Levels
username Sets the user name for PPP authentication. write Stores the current configuration in permanent memory. ppp 2 (ppp:2) level commands authentication mode chap Sets authentication to Challenge-Handshake Authentica- tion Protocol (CHAP). authentication mode ms-chap Sets authentication to MS-CHAP version 1. authentication mode ms-chapv2 Sets authentication to MS-CHAP version 2. authentication mode none Removes PPP authentication. authentication mode pap Sets authentication to Password Authentication Protocol (PAP). clrscrn Clears the screen. default authentication mode Removes PPP authentication. exit Exits to the configuration level. line Enters the line level. = number of the line (serial port) to be configured. local ip Sets the Local IP address and network mask. Formats accepted: 192.168.1.1 (default mask) 192.168.1.1/24 (CIDR) "192.168.1.1 255.255.255.0" (explicit mask) lpd Enters the configure lpd level. = number of the line (lpd serial port) to be config- ured. no local ip Removes the Local IP address. no password Removes the PPP authentication password. no peer ip Removes the peer IP address. no username Removes the PPP authentication username. password Sets the password for PPP authentication. peer ip Sets the IP Address assigned to the peer when requested during negotiation. IP address of the peer device. ppp Enters the serial line PPP level. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. terminal Enters the configure-terminal level. = number of the terminal line (serial port) to be con- figured. terminal network Enters the configure-terminal level for the network. tunnel Enters the tunnel level. = number of the tunnel line (serial port) to be con- figured. username Sets the user name for PPP authentication. write Stores the current configuration in permanent memory. query port (config-query_port) level commands clear counters Zeros Query Port counters clrscrn Clears the screen. exit Returns to the config level. no clear counters Unzeros Query Port counters show Displays statistics and information about the query port.
MatchPort® AR Embedded Device Server Command Reference 140 5: Commands and Levels
show history Displays the last 20 commands entered during the current CLI session. state disable Disables response to 77FE requests. state enable Permits response to 77FE requests. write Stores the current configuration in permanent memory. root level commands clrscrn Clears the screen. enable Enters the enable level. exit Exit from the system ping Ping destination continuously with 5 second timeout ping Ping destination n times with 5 second timeout ping Ping destination n times with x timeout (in seconds) show Show system information show history Displays the last 20 commands entered during the current CLI session. show matchport_ar Show system information trace route Trace route to destination rss (config-rss) level commands clear rss Clear the RSS Feed data clrscrn Clears the screen. default max entries Restores the default number of RSS feed entries. exit Exits to the configuration level. feed disable Disables RSS feed. feed enable Enables RSS feed. max entries Sets the maximum number of RSS feed entries. persist disable Disables RSS feed data persistence. persist enable Enables RSS feed data persistence. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. show status Display the RSS Feed status write Stores the current configuration in permanent memory. rss (modbus-rss) level commands clrscrn Clears the screen. exit Exits to the next higher level. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. trace input disable Disables RSS trace of Modbus PDUs received on the serial line. trace input enable Enables RSS trace of Modbus PDUs received on the seri- al line. write Stores the current configuration in permanent memory. serial (tunnel-serial:2) level commands clrscrn Clears the screen. default dtr Restores default DTR control, asserted while connected. dtr asserted while connected Asserts DTR whenever a connect or accept mode tunnel connection is active.
MatchPort® AR Embedded Device Server Command Reference 141 5: Commands and Levels
dtr continuously asserted Asserts DTR regardless of any connections. dtr truport Asserts DTR to match remote DSR when connected via Telnet. dtr unasserted Does not assert DTR. exit Returns to the tunnel level. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. write Stores the current configuration in permanent memory. serial (tunnel-serial:1) level commands clrscrn Clears the screen. default dtr Restores default DTR control, asserted while connected. dtr asserted while connected Asserts DTR whenever a connect or accept mode tunnel connection is active. dtr continuously asserted Asserts DTR regardless of any connections. dtr truport Asserts DTR to match remote DSR when connected via Telnet. dtr unasserted Does not assert DTR. exit Returns to the tunnel level. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. write Stores the current configuration in permanent memory. server (ssh-server) level commands authorized user Sets authorized username, password, and optionally RSA and/or DSA public keys clrscrn Clears the screen. delete all authorized users Removes all authorized users delete authorized user Remove an authorized user exit Exits to the ssh level. host generate dsa 1024 Generate DSA public and private keys host generate dsa 512 Generate DSA public and private keys host generate dsa 768 Generate DSA public and private keys host generate rsa 1024 Generate RSA public and private keys host generate rsa 512 Generate RSA public and private keys host generate rsa 768 Generate RSA public and private keys host keys Sets RSA or DSA public and/or private keys no host dsa Removes DSA public and private keys no host rsa Removes RSA public and private keys show Show SSH Server settings show authorized user Show information for an authorized user show history Displays the last 20 commands entered during the current CLI session. show host dsa Show full DSA public key show host rsa Show full RSA public key write Stores the current configuration in permanent memory. smtp (config-smtp) level commands clrscrn Clears the screen.
MatchPort® AR Embedded Device Server Command Reference 142 5: Commands and Levels
default relay port Restores the SMTP relay port to its default. exit Exits to the configuration level. no relay address Removes the SMTP relay address. relay address Sets an SMTP relay address to direct all outbound email messages through a mail server. relay port Sets the SMTP relay port. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. write Stores the current configuration in permanent memory. snmp (config-snmp) level commands clrscrn Clears the screen. default read community Clears the SNMP read-only community. default system description Restores the SNMP system description to its default. default system name Restores the SNMP system name to default: the product name. default write community Clears the SNMP read/write community. exit Returns to the config level. no system contact Clears the SNMP system contact. no system location Clears the SNMP system location. read community Sets the SNMP read-only community string. = name of the read-only community string to be set. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. show status Displays the SNMP agent status. state disable Disables the SNMP server. state enable Enables the SNMP server. system contact Sets the SNMP system contact information. = system contact information. system description Sets the SNMP system description. = description of device. system location Sets the SNMP system location. = location of device. system name Sets the SNMP system name. = SNMP system name. traps Enters the next lower level. write Stores the current configuration in permanent memory. write community Sets the SNMP read-write community string. = name of the read-write community string to be set. ssh (ssh) level commands client Enters the SSH Client configuration level. clrscrn Clears the screen. exit Exits to the enable level. server Enters the SSH Server configuration level. show history Displays the last 20 commands entered during the current CLI session.
MatchPort® AR Embedded Device Server Command Reference 143 5: Commands and Levels
write Stores the current configuration in permanent memory. ssh (config-cli-ssh) level commands clear counters Sets the SSH counters to zero. clrscrn Clears the screen. default max sessions Could not find VarID 316 in file http/config/varid_help.mtxt default port Restores the default local port to the SSH server. exit Exits to the CLI level. max sessions Could not find VarID 316 in file http/config/varid_help.mtxt no clear counters Restores the SSH counters to the aggregate values. port Sets the local port that the SSH server uses. = local port number. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics Displays the SSH server statistics. state disable Disables the SSH Server. state enable Enables the SSH Server. write Stores the current configuration in permanent memory. ssl (ssl) level commands authority Adds an Authority Certificate. clrscrn Clears the screen. dsa Adds DSA Certificate and Private Key. exit Exits to the enable level. generate dsa Generates a new Self-Signed DSA Certificate. generate rsa Generates a new Self-Signed RSA Certificate. no dsa Removes DSA Certificate and Private Key no intermediate authority Removes an Intermediate Authority Certificate. = index displayed by "show authority" command. no rsa Removes RSA Certificate and Private Key no trusted authority Removes a Trusted Authority Certificate. = index displayed by "show authority" command. rsa Adds RSA Certificate and Private Key. show Displays Certificate Information. show authority Displays Authority Certificate Information. show history Displays the last 20 commands entered during the current CLI session. write Stores the current configuration in permanent memory. syslog (config-syslog) level commands clrscrn Clears the screen. default local port Restores the default syslog local port. default remote port Restores the default syslog remote port. default severity log level No logging. exit Returns to the config level. host Sets the address of the syslog recipient. = IP address or name of the host. local port Sets the syslog local port. = number of the local port used when making a syslog connection.
MatchPort® AR Embedded Device Server Command Reference 144 5: Commands and Levels
no host Removes the address of the syslog recipient. remote port Sets the syslog remote port. = number of the remote port used when making a syslog connection. severity log level alert Log only Alert and more severe events. severity log level critical Log only Critical and more severe events. severity log level debug Log all events. severity log level emergency Log only Emergency events. severity log level error Log only Error and more severe events. severity log level information Log only Information and more severe events. severity log level none No logging. severity log level notice Log only Notice and more severe events. severity log level warning Log only Warning and more severe events. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics Displays the syslog statistics. state disable Disables syslog logging. state enable Enables syslog logging. write Stores the current configuration in permanent memory. tcp (config-tcp) level commands ack limit Sets the number of packets that must be received before an ACK is forced. If there is a large amount of data to acknowledge, an ACK will be forced before this. auto show statistics Continuously shows TCP statistics clear counters Zeros TCP counters clrscrn Clears the screen. default ack limit Restores the default ack limit of 3 packets. default max retrans Restores the default Maximum Retransmissions. default max retrans syn ack Restores the default Maximum Retransmissions for SYN/ACK. default max timeout Restores the default Maximum Timeout between retrans- missions. default send data Sets TCP to send data in accordance with standards. exit Exits to the configuration level. max retrans Sets the Maximum Retransmisssions. max retrans syn ack Sets the Maximum Retransmisssions for SYN/ACK. It is lower than "Max Retrans" to thwart denial-of-service attacks. max timeout Sets the Maximum Timeout between retransmisssions in seconds. no clear counters Unzeros TCP counters resets disable Does not send TCP RSTs upon connection to unused ports. resets enable Sends TCP RSTs upon connection to unused ports. send data expedited Sets TCP to send data whenever the window is sufficient- ly open, for improved real-time performance.
MatchPort® AR Embedded Device Server Command Reference 145 5: Commands and Levels
send data standard Sets TCP to send data in accordance with standards. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics Shows TCP statistics write Stores the current configuration in permanent memory. telnet (config-cli-telnet) level commands clear counters Sets the Telnet counters to zero. clrscrn Clears the screen. default max sessions Could not find VarID 315 in file http/config/varid_help.mtxt default port Restores the default local port to the Telnet server. exit Exits to the CLI level. max sessions Could not find VarID 315 in file http/config/varid_help.mtxt no clear counters Restores the Telnet counters to the aggregate values. port Sets the local port that the Telnet server uses. = local port number. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics Displays the Telnet statistics. state disable Disables the Telnet Server. state enable Enables the Telnet Server. write Stores the current configuration in permanent memory. terminal 1 (config-terminal:1) level commands break duration Sets how long a break should last when it is being sent to the line. = number of milliseconds. clrscrn Clears the screen. default break duration Restores the break duration to the default value (500 ms). default terminal type Sets the default terminal type, "UNKNOWN". echo disable Disables echoing of characters received on the line back to the line. echo enable Enables echoing of characters received on the line back to the line. exit Exits to the configuration level. exit connect menu disable On the login connect menu, removes the menu item allow- ing the user to exit to the CLI. exit connect menu enable On the login connect menu, inserts the menu item allow- ing the user to exit to the CLI. line Enters the line level. = number of the line (serial port) to be configured. login connect menu disable Disables the login connect menu, so a user will get the CLI immediately after logging in. login connect menu enable Enables the login connect menu, so a user will get the menu rather than the CLI immediately after logging in. lpd Enters the configure lpd level.
MatchPort® AR Embedded Device Server Command Reference 146 5: Commands and Levels
= number of the line (lpd serial port) to be config- ured. no send break Removes the configured send break character. ppp Enters the serial line PPP level. preview connect menu Shows the layout of the connect menu with current set- tings. send break Sets the optional send break character. = the character. The character may be input as text, control, decimal, or hex. A control character has the form C. A decimal value character has the form \99. A hex value character has the form 0xFF. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. terminal Enters the configure-terminal level. = number of the terminal line (serial port) to be con- figured. terminal network Enters the configure-terminal level for the network. terminal type Sets the terminal type. tunnel Enters the tunnel level. = number of the tunnel line (serial port) to be con- figured. write Stores the current configuration in permanent memory. terminal 2 (config-terminal:2) level commands break duration Sets how long a break should last when it is being sent to the line. = number of milliseconds. clrscrn Clears the screen. default break duration Restores the break duration to the default value (500 ms). default terminal type Sets the default terminal type, "UNKNOWN". echo disable Disables echoing of characters received on the line back to the line. echo enable Enables echoing of characters received on the line back to the line. exit Exits to the configuration level. exit connect menu disable On the login connect menu, removes the menu item allow- ing the user to exit to the CLI. exit connect menu enable On the login connect menu, inserts the menu item allow- ing the user to exit to the CLI. line Enters the line level. = number of the line (serial port) to be configured. login connect menu disable Disables the login connect menu, so a user will get the CLI immediately after logging in. login connect menu enable Enables the login connect menu, so a user will get the menu rather than the CLI immediately after logging in. lpd Enters the configure lpd level. = number of the line (lpd serial port) to be config-
MatchPort® AR Embedded Device Server Command Reference 147 5: Commands and Levels
ured. no send break Removes the configured send break character. ppp Enters the serial line PPP level. preview connect menu Shows the layout of the connect menu with current set- tings. send break Sets the optional send break character. = the character. The character may be input as text, control, decimal, or hex. A control character has the form C. A decimal value character has the form \99. A hex value character has the form 0xFF. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. terminal Enters the configure-terminal level. = number of the terminal line (serial port) to be con- figured. terminal network Enters the configure-terminal level for the network. terminal type Sets the terminal type. tunnel Enters the tunnel level. = number of the tunnel line (serial port) to be con- figured. write Stores the current configuration in permanent memory. terminal network (config-terminal:network) level commands break duration Sets how long a break should last when it is being sent to the line. = number of milliseconds. clrscrn Clears the screen. default break duration Restores the break duration to the default value (500 ms). default terminal type Sets the default terminal type, "UNKNOWN". echo disable Disables echoing of characters received on the line back to the line. echo enable Enables echoing of characters received on the line back to the line. exit Exits to the configuration level. exit connect menu disable On the login connect menu, removes the menu item allow- ing the user to exit to the CLI. exit connect menu enable On the login connect menu, inserts the menu item allow- ing the user to exit to the CLI. line Enters the line level. = number of the line (serial port) to be configured. login connect menu disable Disables the login connect menu, so a user will get the CLI immediately after logging in. login connect menu enable Enables the login connect menu, so a user will get the menu rather than the CLI immediately after logging in. lpd Enters the configure lpd level. = number of the line (lpd serial port) to be config- ured.
MatchPort® AR Embedded Device Server Command Reference 148 5: Commands and Levels
no send break Removes the configured send break character. ppp Enters the serial line PPP level. preview connect menu Shows the layout of the connect menu with current set- tings. send break Sets the optional send break character. = the character. The character may be input as text, control, decimal, or hex. A control character has the form C. A decimal value character has the form \99. A hex value character has the form 0xFF. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. terminal Enters the configure-terminal level. = number of the terminal line (serial port) to be con- figured. terminal network Enters the configure-terminal level for the network. terminal type Sets the terminal type. tunnel Enters the tunnel level. = number of the tunnel line (serial port) to be con- figured. write Stores the current configuration in permanent memory. tftp (config-tftp) level commands allow file creation disable Prohibits the TFTP server from creating files on the file system. allow file creation enable Enables the TFTP server to create files on the file system. allow firmware update disable The TFTP server rejects any attempt to update firmware. allow firmware update enable The TFTP server accepts a firmware image for update based on the file name. allow xcr import disable The TFTP server rejects any attempt to import XML con- figuration. allow xcr import enable The TFTP server accepts an XCR file for configuration update based on the file name. clear counters Sets the TFTP counters to zero. clrscrn Clears the screen. exit Returns to the config level. no clear counters Restores the TFTP counters to the aggregate values. show Displays the current configuration. show history Displays the last 20 commands entered during the current CLI session. show statistics Displays the TFTP statistics. state disable Disables the TFTP server. state enable Enables the TFTP server. write Stores the current configuration in permanent memory. traps (config-snmp-traps) level commands clrscrn Clears the screen. exit Exits to the next higher level. no primary destination Deletes the primary SNMP trap host. no secondary destination Deletes the secondary SNMP trap host.
MatchPort® AR Embedded Device Server Command Reference 149 5: Commands and Levels
primary destination Sets the primary SNMP trap host. = IP address of host running the SNMP trap. secondary destination Sets the secondary SNMP trap host. = IP address of host running the SNMP trap. show Shows the current configuration. show history Displays the last 20 commands entered during the current CLI session. state disable Disables the sending of SNMP trap messages. state enable Enables the sending of SNMP trap messages. write Stores the current configuration in permanent memory. tunnel 1 (tunnel:1) level commands accept Enters the accept level for this tunnel. auto show statistics show connection statistics clear counters Zeros all tunnel counters clrscrn Clears the screen. connect Enters the connect level for this tunnel. disconnect Enters the disconnect level for this tunnel. exit Exits to the enable level. line Enters the line level. = number of the line (serial port) to be configured. lpd Enters the configure lpd level. = number of the line (lpd serial port) to be config- ured. modem Enters the modem level for this tunnel. no clear counters Unzeros all tunnel counters packing Enters the packing level for this tunnel. ppp Enters the serial line PPP level. serial Enters the serial level for this tunnel. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics terminal Enters the configure-terminal level. = number of the terminal line (serial port) to be con- figured. terminal network Enters the configure-terminal level for the network. tunnel Enters the tunnel level. = number of the tunnel line (serial port) to be con- figured. write Stores the current configuration in permanent memory. tunnel 2 (tunnel:2) level commands accept Enters the accept level for this tunnel. auto show statistics show connection statistics clear counters Zeros all tunnel counters clrscrn Clears the screen. connect Enters the connect level for this tunnel. disconnect Enters the disconnect level for this tunnel. exit Exits to the enable level. line Enters the line level. = number of the line (serial port) to be configured.
MatchPort® AR Embedded Device Server Command Reference 150 5: Commands and Levels
lpd Enters the configure lpd level. = number of the line (lpd serial port) to be config- ured. modem Enters the modem level for this tunnel. no clear counters Unzeros all tunnel counters packing Enters the packing level for this tunnel. ppp Enters the serial line PPP level. serial Enters the serial level for this tunnel. show history Displays the last 20 commands entered during the current CLI session. show statistics show connection statistics terminal Enters the configure-terminal level. = number of the terminal line (serial port) to be con- figured. terminal network Enters the configure-terminal level for the network. tunnel Enters the tunnel level. = number of the tunnel line (serial port) to be con- figured. write Stores the current configuration in permanent memory. udp (config-udp) level commands auto show statistics Continuously shows UDP statistics clear counters Zeros counters clrscrn Clears the screen. exit Exits to the configuration level. no clear counters Unzeros IP counters show history Displays the last 20 commands entered during the current CLI session. show statistics Shows UDP statistics write Stores the current configuration in permanent memory. vip (config-vip) level commands auto show counters Displays VIP counters continuously. auto show status Displays VIP status continuously. clear counters Sets the VIP counters to zero. clrscrn Clears the screen. exit Exits to the configuration level. no clear counters Restores the VIP counters to the aggregate values. show Displays the current configuration. show counters Displays the VIP counters. show history Displays the last 20 commands entered during the current CLI session. show status Displays the VIP status. state disable Disables use of Virtual IP (VIP) addresses. state enable Enables use of Virtual IP (VIP) addresses. write Stores the current configuration in permanent memory. xml (xml) level commands auto show statistics Show XML statistics clear counters Zeros XML statistics clrscrn Clears the screen.
MatchPort® AR Embedded Device Server Command Reference 151 5: Commands and Levels
exit Exits to the enable level. no clear counters Unzeros XML statistics secret xcr dump Dump XML configuration containing secrets to the console secret xcr dump Dump specified XML configuration containing secrets to the console secret xcr export Save XML configuration containing secrets to a file secret xcr export Save specified XML configuration containing secrets to a local file show history Displays the last 20 commands entered during the current CLI session. show statistics Show XML statistics write Stores the current configuration in permanent memory. xcr dump Dump XML configuration to the console xcr dump Dump specified XML configuration to the console xcr export Save XML configuration to a file xcr export Save specified XML configuration to a local file xcr import Load XML configuration from a local file xcr import Load specified XML configuration from a local file xcr list List XML Configuration Record groups to the console xsr dump Dump XML Status Records to the console xsr dump Dump specified XML Status Records to the console xsr export Save XML Status Record to a file xsr export Save specified XML Status Record to a local file xsr list List XML Status Record groups to the console
MatchPort® AR Embedded Device Server Command Reference 152