Easy Fountain Instructions 45024L - Trellis Garden
Total Page:16
File Type:pdf, Size:1020Kb
Easy Fountain Instructions 45024L - Trellis Garden Please read the assembly and pump operating instructions carefully and observe the safety instructions. STAGE 1 Position the water feature onto a secure and level surface. STAGE 2 Through the opening at the back of the fountain, locate the internal water pipe and attach the end of it onto the pump outlet. STAGE 3 Push the LED cable into the wire which extends from the pump and screw over the plastic collar to secure into place. STAGE 4 Thread the long transformer wire which extends from the pump through the opening in the back of the fountain. Push the cable with 2 pins into the transformer and screw over the plastic collar. STAGE 5 Carefully fill the fountain with sufficient water ensuring that the pump is fully submerged. STAGE 6 Connect the plug to your mains outlet. The transformer should never be submerged or stood in water. Please note the transformer will get hot while in use, this is normal. PUMP FLOW: The pump flow can be adjusted with the ELECTRICAL SAFETY: If outdoors the outlet must be regulator, this is found on the waterproof. We recommend the use of a residual current device inlet of the pump. We (GFI) Ground Fault Interrupter (available from all good D.I.Y. recommend starting with the stores) when connecting the fountain to the electric supply. flow regulator fully open and then adjusting down if required. www.kelkay.com easyfountain® Aftercare Information Cleaning your fountain Caring for your fountain • Clean and top-up the water on a regular basis. The easyfountain® aftercare range includes products to • To empty the fountain of water for cleaning or for help care for your fountain. Please see the table below winter care: for more information. Smaller fountains (that are light enough to be lifted) the water can be emptied by simply inverting the Fountain Algae Stopper 385g • Easy to use fountain and letting the water pour away through a • Removes and prevents algae and bacteria suitable drain or sink. • Will not harm animals and birds Larger (heavier) fountains - water can be removed by using a large sponge or by purchasing a simple Fountain Grime and Lime Cleaner 500ml syphon pipe available from aquatic supply stores. • Easy to use • Always shut off the power before cleaning and • Removes dirt from your water feature maintaining the fountain or pump. • Limescale buster Fountain One Shot Algae Remover 100g Winter care • Easy to use • Removes algae and bacteria ® Guidelines to help protect your easyfountain : • Stops slime build up • If possible, bring your water feature indoors eg. garage or shed. Fountain Citronella Water Scent 125ml • Easy to use • Drain the fountain of all water. If water freezes within • Clean and fresh scent the fountain, this can cause damage. • Helps to repel insects • If your fountain is left outside and drained of all water, a Kelkay easyfountain® cover can be purchased to cover the entire fountain however we cannot Fountain Shine Spray 500ml • Easy to use guarantee that it will protect your fountain from • Helps preserve radiance winter damage. • Leaves a smear free shine Please note: The easyfountain® aftercare range is only available in the UK Troubleshooting and Republic of Ireland. Please check with your nearest stockist for availability. Pumps Leaks/Loss of Water • Check the water is covering the pump by at least 5cm. • Overfilled - make sure the water reservoir is not • Check the flow dial on the pump to ensure the correct overfilled. Remove water if necessary. “flow” for the fountain is set. • Pump Flow Rate - check the pump and reduce the • Check to see if it is running if it is then it is probably flow rate if required. blocked. • Level - ensure the fountain is completely level. • Clear the pipe and impeller from blockages. • Natural evaporation, weather elements and wildlife • Check the fuse in the plug. will also affect the fountain water level on a daily Lights/Transformers basis. Top up your fountain as required. • If the lights and the pump are not working it is likely the Main Body & Paintwork transformer has failed. If the product is within the • Do not confuse limescale residue with fading paint - warranty period and misuse has not occurred a this is not a fault and in most cases the fountain replacement part can be issued providing a proof of needs cleaning. purchase is supplied. • Paint peeling will occur if the fountain has been left • Flickering lights are caused by a build-up of algae and outside in the frost and will not be covered by the lime scale on the connectors between the transformer warranty. and the lights. This is not covered by the warranty. • Parts broken off the main body while in use are Replacement parts can be purchased from Kelkay LTD. usually caused by bad weather conditions and not • If the lights stop working they are available to purchase covered by the warranty. from Kelkay LTD. Light bulbs are not covered under the warranty. • Individual L.E.D lights are not replaceable but can be replaced as a set. www.kelkay.com.