DOCSLIB.ORG

Theoretical and Experimental Studies of Heavy Liquid Metal Thermal Hydraulics

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Theoretical and Experimental Studies of Heavy Liquid Metal Thermal Hydraulics IAEA-TECDOC-1520 Theoretical and Experimental Studies of Heavy Liquid Metal Thermal Hydraulics Proceedings of a technical meeting held in Karlsruhe, Germany, 28–31 October 2003 October 2006 IAEA-TECDOC-1520 Theoretical and Experimental Studies of Heavy Liquid Metal Thermal Hydraulics Proceedings of a technical meeting held in Karlsruhe, Germany, 28–31 October 2003 October 2006 The originating Section of this publication in the IAEA was: Radiation and Transport Safety Section International Atomic Energy Agency Wagramer Strasse 5 P.O. Box 100 A-1400 Vienna, Austria THEORETICAL AND EXPERIMENTAL STUDIES OF HEAVY LIQUID METAL THERMAL HYDRAULICS IAEA, VIENNA, 2006 IAEA-TECDOC-1520 ISBN 92–0–111806–6 ISSN 1011–4289 © IAEA, 2006 Printed by the IAEA in Austria October 2006 FOREWORD Through the Nuclear Energy Department’s Technical Working Group on Fast Reactors (TWG-FR), the IAEA provides a forum for exchange of information on national programmes, collaborative assessments, knowledge preservation, and cooperative research in areas agreed by the Member States with fast reactor and partitioning and transmutation development programmes (e.g. accelerator driven systems (ADS)). Trends in advanced fast reactor and ADS designs and technology development are periodically summarized in status reports, symposia, and seminar proceedings prepared by the IAEA to provide all interested IAEA Member States with balanced and objective information. The use of heavy liquid metals (HLM) is rapidly diffusing in different research and industrial fields. The detailed knowledge of the basic thermal hydraulics phenomena associated with their use is a necessary step for the development of the numerical codes to be used in the engineering design of HLM components. This is particularly true in the case of lead or lead-bismuth eutectic alloy cooled fast reactors, high power particle beam targets and in the case of the cooling of accelerator driven sub-critical cores where the use of computational fluid dynamic (CFD) design codes is mandatory. Periodic information exchange within the frame of the TWG-FR has lead to the conclusion that the experience in HLM thermal fluid dynamics with regard to both the theoretical/numerical and experimental fields was limited and somehow dispersed. This is the case, e.g. when considering turbulent exchange phenomena, free-surface problems, and two-phase flows. Consequently, Member States representatives participating in the 35th Annual Meeting of the TWG-FR (Karlsruhe, Germany, 22–26 April 2002) recommended holding a technical meeting (TM) on Theoretical and Experimental Studies of Heavy Liquid Metal Thermal Hydraulics. Following this recommendation, the IAEA has convened the Technical Meeting on Theoretical and Experimental Studies of Heavy Liquid Metal Thermal Hydraulics (28– 31 October 2003). The TM was hosted by the Forschungszentrum Karlsruhe, Germany. The scope of the TM was to provide a global forum for information exchange on the most recent theoretical and experimental studies of HLM thermal hydraulics. The main objective of the TM was to assess the shortcomings of the present CFD codes used for HLM simulation and to identify future research needs, in both the numerical and experimental area. The IAEA would like to express its appreciation to all the participants, authors of papers, chairpersons, and to the hosts at Forschungszentrum Karlsruhe. The IAEA officer responsible for this publication was A. Stanculescu of the Division of Nuclear Power. EDITORIAL NOTE The papers in these proceedings are reproduced as submitted by the authors and have not undergone rigorous editorial review by the IAEA. The views expressed do not necessarily reflect those of the IAEA, the governments of the nominating Member States or the nominating organizations. The use of particular designations of countries or territories does not imply any judgement by the publisher, the IAEA, as to the legal status of such countries or territories, of their authorities and institutions or of the delimitation of their boundaries. The mention of names of specific companies or products (whether or not indicated as registered) does not imply any intention to infringe proprietary rights, nor should it be construed as an endorsement or recommendation on the part of the IAEA. The authors are responsible for having obtained the necessary permission for the IAEA to reproduce, translate or use material from sources already protected by copyrights. CONTENTS SUMMARY ............................................................................................................................... 1 SESSION 1: REVIEW OF THE STATE OF ART OF PRESENT CDF CODES Turbulence modeling issues in ADS thermal and hydraulic analyses ....................................... 9 G. Groetzbach Two CFD applications to the design of the active zone of HLM spallation targets................................................................................................................... 33 P. Roubin CFD analysis of the thermal-hydraulic performance of the ESS target................................... 49 E.M.J. Komen, F. Roelofs, J. Wolters, G. Hansen Validation of CFD models with respect to the thermal-hydraulic design of the ESS target................................................................................................................... 59 J. Wolters, G. Hansen, E.M.J. Komen, F. Roelofs CFD analysis of the heavy liquid metal flow field in the MYRRHA pool.............................. 77 E.M.J. Komen, P. Kupschus, K. Van Tichelen, H. Aït Abderrahim, F. Roelofs Comparative analysis of the benchmark activity results on the ADS target model.......................................................................................................................... 89 A. Sorokin, G. Bogoslovskaia, V. Mikhin, S. Marzinuk Free surface fluid dynamics code adaptation by experimental evidence for the MYRRHA spallation target .................................................................................... 101 K. Van Tichelen, P. Kupschus, M. Dierckx, H. Aït Abderrahim, F. Roelofs Thermohydraulic behaviour in an ADS target model ............................................................ 111 A. Peña, G.A. Esteban, J. Sancho Development and application of CFD codes MASKA-LM and PORT 3D for investigation of thermal hydraulics of lead cooled fast reactor BREST ............................ 119 A.A. Veremeev, V.Ya. Kumayev, A.A. Lebezov CFD simulation of X-ADS downcomer thermal stratification .............................................. 135 V. Anissimov, A. Alemberti Experiences from using the STAR-CD code for Pb-Bi-coolant flows .................................. 151 J. Carlsson, H. Wider CFD simulation of SINQ HETSS mercury experiments ....................................................... 165 T.V. Dury SESSION 2: REVIEW OF CURRENT AND PLANNED EXPERIMENTAL HLM PROGRAMS Thermal hydraulic research and development needs for lead fast reactors............................ 195 J.J. Sienicki, D.C. Wade, C.P. Tzanos Thermohydraulic research for the core of the BREST reactor............................................... 213 A.V. Zhukov, A.D. Efanov, A.P. Sorokin, J.A. Kuzina, V.P. Smirnov, A.I. Filin, A.G. Sila-Novitsky, V.N. Leonov Pre-test analysis of the MEGAPIE integral test with RELAP5 ............................................. 227 W.H. Leung, B. Sigg Experimental determination of the local heat transfer coefficient for MEGAPIE target window using infrared thermography ................................................... 243 J.A. Patorski, F. Gröschel, I. Platnieks Thermal-hydraulic ADS lead bismuth loop (tall) and experiments on a heat exchanger............................................................................................................ 259 B.R. Sehgal, W.M. Ma, A. Karbojian HELIOS for thermal-hydraulic behaviour of Pb-Bi cooled fast reactor peacer..................... 271 I.S. Lee, K.Y. Suh Void-fraction measurements in two-phase nitrogen-mercury flows...................................... 295 P. Satyamurthy, N.S. Dixit, P. Munshi SESSION 3: ELABORATION OF FUTURE ACTIVITIES Studies on heavy liquid metal thermal-hydraulics: Existing test facilities and test programs............................................................................ 307 J.U. Knebel, C. Fazio LIST OF PARTICIPANTS .................................................................................................... 315 SUMMARY 1. INTRODUCTION The use of heavy liquid metals (HLM) is rapidly diffusing in different research and industrial fields. The detailed knowledge of the basic thermal hydraulics phenomena associated with their use is a necessary step for the development of the numerical codes to be used in the R&D as well as in the engineering design of HLM components. This is particularly true in the case of high power particle beam targets and in the case of the cooling of accelerator driven sub-critical cores where the use of computational fluid dynamic (CFD) design codes is mandatory. The scope of the topical Technical Meeting on Theoretical and Experimental Studies of Heavy Liquid Metal Thermal Hydraulics was to provide a global forum for information exchange on the most recent theoretical and experimental studies of HLM thermal hydraulics. The main objective of the technical meeting was the assessment of the shortcomings of the present CFD codes used for HLM simulation and to propose future research activities, in both the numerical and experimental area. More specifically, the technical meeting:
Load more

Recommended publications
  • The Role of MHD Turbulence in Magnetic Self-Excitation in The
    THE ROLE OF MHD TURBULENCE IN MAGNETIC SELF-EXCITATION: A STUDY OF THE MADISON DYNAMO EXPERIMENT by Mark D. Nornberg A dissertation submitted in partial fulfillment of the requirements for the degree of Doctor of Philosophy (Physics) at the UNIVERSITY OF WISCONSIN–MADISON 2006 °c Copyright by Mark D. Nornberg 2006 All Rights Reserved i For my parents who supported me throughout college and for my wife who supported me throughout graduate school. The rest of my life I dedicate to my daughter Margaret. ii ACKNOWLEDGMENTS I would like to thank my adviser Cary Forest for his guidance and support in the completion of this dissertation. His high expectations and persistence helped drive the work presented in this thesis. I am indebted to him for the many opportunities he provided me to connect with the world-wide dynamo community. I would also like to thank Roch Kendrick for leading the design, construction, and operation of the experiment. He taught me how to do science using nothing but duct tape, Sharpies, and Scotch-Brite. He also raised my appreciation for the artistry of engineer- ing. My thanks also go to the many undergraduate students who assisted in the construction of the experiment, especially Craig Jacobson who performed graduate-level work. My research partner, Erik Spence, deserves particular thanks for his tireless efforts in modeling the experiment. His persnickety emendations were especially appreciated as we entered the publi- cation stage of the experiment. The conversations during our morning commute to the lab will be sorely missed. I never imagined forging such a strong friendship with a colleague, and I hope our families remain close despite great distance.
    [Show full text]
  • Liquid Metal Cooled Reactors: Experience in Design and Operation
    IAEA-TECDOC-1569 Liquid Metal Cooled Reactors: Experience in Design and Operation December 2007 IAEA-TECDOC-1569 Liquid Metal Cooled Reactors: Experience in Design and Operation December 2007 The originating Sections of this publication in the IAEA were: INIS and Nuclear Knowledge Management and Nuclear Power Technology Development Sections International Atomic Energy Agency Wagramer Strasse 5 P.O. Box 100 A-1400 Vienna, Austria LIQUID METAL COOLED REACTORS: EXPERIENCE IN DESIGN AND OPERATION IAEA, VIENNA, 2007 IAEA-TECDOC-1569 ISBN 978–92–0–107907–7 ISSN 1011–4289 © IAEA, 2007 Printed by the IAEA in Austria December 2007 FOREWORD In 2002, within the framework of the Department of Nuclear Energy’s Technical Working Group on Fast Reactors (TWG-FR), and according to the expressed needs of the TWG-FR Member States to maintain and increase the present knowledge and expertise in fast reactor science and technology, the IAEA established its initiative seeking to establish a comprehensive, international inventory of fast reactor data and knowledge. More generally, at the IAEA meeting of senior officials convened to address issues of nuclear knowledge management underlying the safe and economic use of nuclear science and technology (Vienna, 17–19 June 2002), there was widespread agreement that, for sustainability reasons for fissile sources and waste management, long-term development of nuclear power as a part of the world’s future energy mix will require the fast reactor technology. Furthermore, given the decline in fast reactor development projects, data retrieval and knowledge preservation efforts in this area are of particular importance. This consensus concluded from the recognition of immediate need gave support to the IAEA initiative for fast reactor data and knowledge presevation.
    [Show full text]
  • Chapter 5 Dimensional Analysis and Similarity
    Chapter 5 Dimensional Analysis and Similarity Motivation. In this chapter we discuss the planning, presentation, and interpretation of experimental data. We shall try to convince you that such data are best presented in dimensionless form. Experiments which might result in tables of output, or even mul- tiple volumes of tables, might be reduced to a single set of curves—or even a single curve—when suitably nondimensionalized. The technique for doing this is dimensional analysis. Chapter 3 presented gross control-volume balances of mass, momentum, and en- ergy which led to estimates of global parameters: mass flow, force, torque, total heat transfer. Chapter 4 presented infinitesimal balances which led to the basic partial dif- ferential equations of fluid flow and some particular solutions. These two chapters cov- ered analytical techniques, which are limited to fairly simple geometries and well- defined boundary conditions. Probably one-third of fluid-flow problems can be attacked in this analytical or theoretical manner. The other two-thirds of all fluid problems are too complex, both geometrically and physically, to be solved analytically. They must be tested by experiment. Their behav- ior is reported as experimental data. Such data are much more useful if they are ex- pressed in compact, economic form. Graphs are especially useful, since tabulated data cannot be absorbed, nor can the trends and rates of change be observed, by most en- gineering eyes. These are the motivations for dimensional analysis. The technique is traditional in fluid mechanics and is useful in all engineering and physical sciences, with notable uses also seen in the biological and social sciences.
    [Show full text]
  • Cavitation in Valves
    VM‐CAV/WP White Paper Cavitation in Valves Table of Contents Introduction. 2 Cavitation Analysis. 2 Cavitation Data. 3 Valve Coefficient Data. 4 Example Application. .. 5 Conclusion & Recommendations . 5 References. 6 Val‐Matic Valve & Mfg. Corp. • www.valmatic.com • [email protected] • PH: 630‐941‐7600 Copyright © 2018 Val‐Matic Valve & Mfg. Corp. Cavitation in Valves INTRODUCTION Cavitation can occur in valves when used in throttling or modulating service. Cavitation is the sudden vaporization and violent condensation of a liquid downstream of the valve due to localized low pressure zones. When flow passes through a throttled valve, a localized low pressure zone forms immediately downstream of the valve. If the localized pressure falls below the vapor pressure of the fluid, the liquid vaporizes (boils) and forms a vapor pocket. As the vapor bubbles flow downstream, the pressure recovers, and the bubbles violently implode causing a popping or rumbling sound similar to tumbling rocks in a pipe. The sound of cavitation in a pipeline is unmistakable. The condensation of the bubbles not only produces a ringing sound, but also creates localized stresses in the pipe walls and valve body that can cause severe pitting. FIGURE 1. Cavitation Cavitation is a common occurrence in shutoff valves during the last few degrees of closure when the supply pressure is greater than about 100 psig. Valves can withstand limited durations of cavitation, but when the valve must be throttled or modulated in cavitating conditions for long periods of time, the life of the valve can be drastically reduced. Therefore, an analysis of flow conditions is needed when a valve is used for flow or pressure control.
    [Show full text]
  • Control Valve Sizing Theory, Cavitation, Flashing Noise, Flashing and Cavitation Valve Pressure Recovery Factor
    Control Valve Sizing Theory, Cavitation, Flashing Noise, Flashing and Cavitation Valve Pressure Recovery Factor When a fluid passes through the valve orifice there is a marked increase in velocity. Velocity reaches a maximum and pressure a minimum at the smallest sectional flow area just downstream of the orifice opening. This point of maximum velocity is called the Vena Contracta. Downstream of the Vena Contracta the fluid velocity decelerates and the pressure increases of recovers. The more stream lined valve body designs like butterfly and ball valves exhibit a high degree of pressure recovery where as Globe style valves exhibit a lower degree of pressure recovery because of the Globe geometry the velocity is lower through the vena Contracta. The Valve Pressure Recovery Factor is used to quantify this maximum velocity at the vena Contracta and is derived by testing and published by control valve manufacturers. The Higher the Valve Pressure Recovery Factor number the lower the downstream recovery, so globe style valves have high recovery factors. ISA uses FL to represent the Valve Recovery Factor is valve sizing equations. Flow Through a restriction • As fluid flows through a restriction, the Restriction Vena Contracta fluid’s velocity increases. Flow • The Bernoulli Principle P1 P2 states that as the velocity of a fluid or gas increases, its pressure decreases. Velocity Profile • The Vena Contracta is the point of smallest flow area, highest velocity, and Pressure Profile lowest pressure. Terminology Vapor Pressure Pv The vapor pressure of a fluid is the pressure at which the fluid is in thermodynamic equilibrium with its condensed state.
    [Show full text]
  • Eulerian–Lagrangian Method for Simulation of Cloud Cavitation ∗ Kazuki Maeda , Tim Colonius
    Journal of Computational Physics 371 (2018) 994–1017 Contents lists available at ScienceDirect Journal of Computational Physics www.elsevier.com/locate/jcp Eulerian–Lagrangian method for simulation of cloud cavitation ∗ Kazuki Maeda , Tim Colonius Division of Engineering and Applied Science, California Institute of Technology, 1200 East California Boulevard, Pasadena, CA 91125, USA a r t i c l e i n f o a b s t r a c t Article history: We present a coupled Eulerian–Lagrangian method to simulate cloud cavitation in a Received 3 December 2017 compressible liquid. The method is designed to capture the strong, volumetric oscillations Received in revised form 10 April 2018 of each bubble and the bubble-scattered acoustics. The dynamics of the bubbly mixture Accepted 16 May 2018 is formulated using volume-averaged equations of motion. The continuous phase is Available online 18 May 2018 discretized on an Eulerian grid and integrated using a high-order, finite-volume weighted Keywords: essentially non-oscillatory (WENO) scheme, while the gas phase is modeled as spherical, Bubble dynamics Lagrangian point-bubbles at the sub-grid scale, each of whose radial evolution is tracked Cavitation by solving the Keller–Miksis equation. The volume of bubbles is mapped onto the Eulerian Eulerian–Lagrangian method grid as the void fraction by using a regularization (smearing) kernel. In the most general Compressible multiphase flows case, where the bubble distribution is arbitrary, three-dimensional Cartesian grids are used Multiscale modeling for spatial discretization. In order to reduce the computational cost for problems possessing Reduced-order modeling translational or rotational homogeneities, we spatially average the governing equations along the direction of symmetry and discretize the continuous phase on two-dimensional or axi-symmetric grids, respectively.
    [Show full text]
  • (12) Patent Application Publication (10) Pub. No.: US 2006/0090474 A1 Sauciuc Et Al
    US 20060090474A1 (19) United States (12) Patent Application Publication (10) Pub. No.: US 2006/0090474 A1 Sauciuc et al. (43) Pub. Date: May 4, 2006 (54) METHOD AND APPARATUS FOR Publication Classification REMOVING HEAT (51) Int. Cl. F2SB 2L/02 (2006.01) (76) Inventors: Ioan Sauciuc, Phoeniz, AZ (US); Jim F28D 5/00 (2006.01) D. Williams, Banks, OR (US) F25D 23/12 (2006.01) (52) U.S. Cl. ....................... 62/3.2: 62/259.2; 165/104.22 Correspondence Address: BLAKELY SOKOLOFFTAYLOR & ZAFMAN (57) ABSTRACT 124OO WILSHIRE BOULEVARD SEVENTH FLOOR A device includes a liquid metal and a ferrofluid contained LOS ANGELES, CA 90025-1030 (US) in a closed tube. Many electrode groups are connected to the closed tube. A feedback device is connected to the electrode (21) Appl. No.: 10/976,406 groups. The feedback device switches power to each elec trode group in series to circulate the liquid metal and move (22) Filed: Oct. 29, 2004 the ferrofluid in the closed tube. 200 210 -4220 Automatic feedback system and StartUp Circuit (2) (25 260 250 Patent Application Publication May 4, 2006 Sheet 1 of 7 US 2006/0090474 A1 20 FIG. 1A F.G. 1B (Prior Art) (Pr O Art) Patent Application Publication May 4, 2006 Sheet 2 of 7 US 2006/0090474 A1 200 - Automatic feedback system and StartUp Circuit 25 (25 240 E.iSE S3 ES 230 250 FIG. 2 Patent Application Publication May 4, 2006 Sheet 3 of 7 US 2006/0090474 A1 FIG. 3 Patent Application Publication May 4, 2006 Sheet 4 of 7 US 2006/0090474 A1 400 Determine Temperature Alternate power to electrode groups to move ferrofluid 420 Circulate liquid metal Dissipate heat within the liquid metal FIG.
    [Show full text]
  • A Numerical Algorithm for MHD of Free Surface Flows at Low Magnetic Reynolds Numbers
    A Numerical Algorithm for MHD of Free Surface Flows at Low Magnetic Reynolds Numbers Roman Samulyak1, Jian Du2, James Glimm1;2, Zhiliang Xu1 1Computational Science Center, Brookhaven National Laboratory, Upton, NY 11973 2 Department of Applied Mathematics and Statistics, SUNY at Stony Brook, Stony Brook, NY 11794, USA November 7, 2005 Abstract We have developed a numerical algorithm and computational soft- ware for the study of magnetohydrodynamics (MHD) of free surface flows at low magnetic Reynolds numbers. The governing system of equations is a coupled hyperbolic/elliptic system in moving and ge- ometrically complex domains. The numerical algorithm employs the method of front tracking for material interfaces, high resolution hy- perbolic solvers, and the embedded boundary method for the elliptic problem in complex domains. The numerical algorithm has been imple- mented as an MHD extension of FronTier, a hydrodynamic code with free interface support. The code is applicable for numerical simulations of free surface conductive liquids or flows of weakly ionized plasmas. Numerical simulations of the Muon Collider/Neutrino Factory target have been discussed. 1 Introduction Computational magnetohydrodynamics, greatly inspired over the last decades by the magnetic confinement fusion and astrophysics problems, has achieved significant results. However the major research effort has been in the area of highly ionized plasmas. Numerical methods and computational software for MHD of weakly conducting materials such as liquid metals or weakly ionized plasmas have not been developed to such an extent despite the need 1 for fusion research and industrial technologies. Liquid metal MHD, driven by potential applications of flowing liquid metals or electrically conducting liquid salts as coolant in magnetic confinement fusion reactors as well as some industrial problems, has attracted broad theoretical, computational, and experimental studies (see [16, 17, 18] and references therein).
    [Show full text]
  • Toward a Self-Generating Magnetic Dynamo: the Role of Turbulence
    PHYSICAL REVIEW E VOLUME 61, NUMBER 5 MAY 2000 Toward a self-generating magnetic dynamo: The role of turbulence Nicholas L. Peffley, A. B. Cawthorne, and Daniel P. Lathrop* Department of Physics, University of Maryland, College Park, Maryland 20742 ͑Received 6 July 1999͒ Turbulent flow of liquid sodium is driven toward the transition to self-generating magnetic fields. The approach toward the transition is monitored with decay measurements of pulsed magnetic fields. These mea- surements show significant fluctuations due to the underlying turbulent fluid flow field. This paper presents experimental characterizations of the fluctuations in the decay rates and induced magnetic fields. These fluc- tuations imply that the transition to self-generation, which should occur at larger magnetic Reynolds number, will exhibit intermittent bursts of magnetic fields. PACS number͑s͒: 47.27.Ϫi, 47.65.ϩa, 05.45.Ϫa, 91.25.Cw I. INTRODUCTION Reynolds number will be quite large for all flows attempting to self-generate ͑where Re ӷ1 yields Reӷ105)—implying The generation of magnetic fields from flowing liquid m turbulent flow. These turbulent flows will cause the transition metals is being pursued by a number of scientific research to self-generation to be intermittent, showing both growth groups in Europe and North America. Nuclear engineering and decay of magnetic fields irregularly in space and time. has facilitated the safe use of liquid sodium, which has con- This intermittency is not something addressed by kinematic tributed to this new generation of experiments. With the dynamo studies. The analysis in this paper focuses on three highest electrical conductivity of any liquid, sodium retains main points: we quantify the approach to self-generation and distorts magnetic fields maximally before they diffuse with increasing Rem , characterize the turbulence of induced away.
    [Show full text]
  • Numerical Study of Cavitation Within Orifice Flow
    NUMERICAL STUDY OF CAVITATION WITHIN ORIFICE FLOW A Thesis by PENGZE YANG Submitted to the Office of Graduate and Professional Studies of Texas A&M University in partial fulfillment of the requirements for the degree of MASTER OF SCIENCE Chair of Committee, Robert Handler Committee Members, David Staack Prabir Daripa Head of Department, Andreas Polycarpou December 2015 Major Subject: Mechanical Engineering Copyright 2015 Pengze Yang ABSTRACT Cavitation generally occurs when the pressure at certain location drops to the vapor pressure and the liquid water evaporates as a consequence. For the past several decades, numerous experimental researches have been conducted to investigate this phenomenon due to its degradation effects on hydraulic device structures, such as erosion, noise and vibration. A plate orifice is an important restriction device that is widely used in many industries. It serves functions as restricting flow and measuring flow rate within a pipe. The plate orifice is also subject to intense cavitation at high pressure difference, therefore, the simulation research of the cavitation phenomenon within an orifice flow becomes quite essential for understanding the causes of cavitation and searching for possible preventing methods. In this paper, all researches are simulation-oriented by using ANSYS FLUENT due to its high resolution comparing to experiments. Standard orifice plates based on ASME PTC 19.5-2004 are chosen and modeled in the study with the diameter ratio from 0.2 to 0.75. Steady state studies are conducted for each diameter ratio at the cavitation number roughly from 0.2 to 2.5 to investigate the dependency of discharge coefficient on the cavitation number.
    [Show full text]
  • Liquid-Based Reconfigurable Antenna Technology
    sensors Review Liquid-Based Reconfigurable Antenna Technology: Recent Developments, Challenges and Future Habshah Abu Bakar 1, Rosemizi Abd Rahim 2,* , Ping Jack Soh 2,3 and Prayoot Akkaraekthalin 4,* 1 Department of Electrical Engineering, Politeknik Sultan Abdul Halim Muadzam Shah, Jitra 06000, Kedah, Malaysia; [email protected] 2 Faculty of Electronic Engineering Technology, Pauh Putra Campus, Universiti Malaysia Perlis, Pauh 02600, Perlis, Malaysia; [email protected] 3 Advanced Communication Engineering (ACE) Centre of Excellence, Universiti Malaysia Perlis, Kangar 01000, Perlis, Malaysia 4 Department of Electrical and Computer Engineering, Faculty of Engineering, King Mongkut’s University of Technology North Bangkok (KMUTNB), 1518 Pracharat 1 Rd., Wongsawang, Bangsue, Bangkok 10800, Thailand * Correspondence: [email protected] (R.A.R.); [email protected] (P.A.) Abstract: Advances in reconfigurable liquid-based reconfigurable antennas are enabling new pos- sibilities to fulfil the requirements of more advanced wireless communication systems. In this review, a comparative analysis of various state-of-the-art concepts and techniques for designing reconfigurable antennas using liquid is presented. First, the electrical properties of different liquids at room temperature commonly used in reconfigurable antennas are identified. This is followed by a discussion of various liquid actuation techniques in enabling high frequency reconfigurability. Next, the liquid-based reconfigurable antennas in literature used to achieve
    [Show full text]
  • A Complete Interfacial System Solution for Liquid Metal Electronics
    A Complete Interfacial System Solution for Liquid Metal Electronics A dissertation submitted to the Graduate School of the University of Cincinnati in partial fulfillment of the requirements for the degree of Doctor of Philosophy in the Department of Materials Science & Engineering of the College of Engineering & Applied Science by Sarah E. Holcomb B.S., Rensselaer Polytechnic Institute, 2013 Committee Chair: Jason C. Heikenfeld, Ph.D. Abstract Liquid metal electronic devices have numerous advantages over traditional solid devices such as the ability to be flexed and stretched or reconfigured. Examples of such devices are wires, switches, polarizers, and antennas. Previously, mercury has been used as the room temperature liquid metal of choice but has been recently replaced by gallium liquid metal alloys (GaLMAs) which are non-toxic, have extremely low vapor pressures, and can remain liquid at temperatures as low as -19°C. A key difference in the performance of GaLMAs vs. mercury is the mechanically stabilizing, passivating oxide which forms instantly on the surface of GaLMAs in as little as 1 ppm oxygen environments. This oxide presents a significant challenge for reconfigurable device applications because it “sticks” to most surfaces, preventing reversible shape change, which alters the desired electrical performance. Proposed here are two novel methods of overcoming this challenge. These methods enable new capabilities for reconfigurable electronic devices. The first approach involves removing the oxide in situ as it is continuously formed in all practically achievable device environments. Oxide removal is commonly done through the use of hydrochloric acid (aqueous or vapor), which reacts with the gallium oxide to produce gallium chloride, which is not mechanically stabilizing, and water.
    [Show full text]