9.2 Raoult's Law and Henry's

Total Page:16

File Type:pdf, Size:1020Kb

9.2 Raoult's Law and Henry's Chapter 9 The Behavior of Solutions 1 9.2 Raoult’s Law and Henry’s Law (1) Initially evacuated vessel at T liq. A (2) spontaneously evaporate until P in the vessel ° reaches the saturated vapor pressure of liq. A, p A, at T (3) a dynamic equilibrium established between the rate of evaporation of liq. A & the rate of condensation of vapor A. 2 9.2 Raoult’s Law and Henry’s Law • re(A) α the # of A atoms in the vapor phase, ° thus, rc(A) = kp A , and at equilibrium (9.1) • Similarly, pure liquid B (9.2) re(A) rc(A) liq. A 3 9.2 Raoult’s Law and Henry’s Law (A) the effect of the small addition of liquid B to liquid A Assume (1) the composition of the surface of the liquid = that of the bulk liquid, XA, (2) the sizes of A & B atoms comparable (9.3) (9.4) 4 9.2 Raoult’s Law and Henry’s Law • From (9.1) and (9.3) gives (9.5) and from (9.2) and (9.4) gives (9.6) • Raoult’s law: the vapor pressure exerted by a component i in a solution = (the mole fraction of i in the solution) X (the saturated vapor pressure of pure liquid i ) at T of the solution. 5 9.2 Raoult’s Law and Henry’s Law • Requirements: the intrinsic rates of evaporation of A and B ≠ f(comp. of the solution) i.e., the magnitudes of the A-A, B-B, and A-B bond energies in the solution are identical 6 9.2 Raoult’s Law and Henry’s Law (B) If A-B >> A-A and B-B and a solution of A in B is sufficiently dilute: A atom at the surface surrounded only by B, A in a deeper potential E well than are the A atoms at the surface of pure liq… difficult to be lifted to vapor, evaporation rate is decreased to re(A) to re’(A) 7 9.2 Raoult’s Law and Henry’s Law (9.7) re(A) > re’(A) (9.8) ’ (9.9) • A similar consideration of dilute solutions of B in A gives ’ (9.10) • (9.9),(9.10) : Henry’ law 8 9.2 Raoult’s Law and Henry’s Law Beyond a critical value of XA, re’(A) becomes composition- dependent. Henry’s law works only over initial conc. range in reality. A-A, B-B attraction greater A-B attraction greater 9 9.3 The Thermodynamic Activity of a Component in Sol’n (9.11) If the vapor above the solution is ideal (9.12) • If the component i exhibits Raoultian behavior, then (9.13) (9.14) 10 9.3 The Thermodynamic Activity of a Component in Sol’n 11 9.4 The Gibbs-Duhem Equation • In many cases, the extensive properties of a component in a multicomponent solution are amenable to exp. measurement ! • The other component’s prop. can be obtained by a general relationship i.e., Gibbs-Duhem Eq. • Q is an extensive molar property 12 9.4 The Gibbs-Duhem Equation at const. T and P The partial molar value 13 9.4 The Gibbs-Duhem Equation If differentiate, From the comparison of (9.16) & (9.18) Gibbs – Duhem Eq. 14 9.5 The Gibbs Free Energy of Formation of a Solution * Molar free E of a solution & partial molar f.e. of solution of composnents w/ free energy as an extensive prop. (9.21) For 1 mole of solution (9.22) (9.23) =0 by G-D (9.24) (9.25) (9.26) (9.27a) 15 9.5 The Gibbs Free Energy of Formation of a Solution (9.27b) 16 9.5 The Gibbs Free Energy of Formation of a Solution * The free E change due to the formation of a solution P o equil. @ T o i Pi > Pi o Vapor, Pi (b) decrease to Pi pure i pure i (a) (c) evaporation condensation 1 mole (d) ∆G(d) = ∆G(a) + ∆G(b) + ∆G(c) = 17 9.5 The Gibbs Free Energy of Formation of a Solution o Pi equil. @ T (9.28) pure i o Pi > Pi pure i 18 9.5 The Gibbs Free Energy of Formation of a Solution The Change in Gibbs Free Energy Due to the Formation of a Solution (9.29) or (9.30) for 1 mole of solution (9.31) (9.32) 19 9.5 The Gibbs Free Energy of Formation of a Solution (9.33a) (9.33b) 20 9.6 The Properties of Raoultian Ideal Solutions • Raoultian : • For an ideal binary A-B solution (9.34) 21 9.6 The Properties of Raoultian Ideal Solutions • For the species i occurring in a solution (9.35) • For pure i (9.36) 22 9.6 The Properties of Raoultian Ideal Solutions (i) The Change in Volume Accompanying the Formation of an Ideal Solution (9.37) (9.38) 23 9.6 The Properties of Raoultian Ideal Solutions 24 9.6 The Properties of Raoultian Ideal Solutions (ii) The Heat of Formation of an Ideal Solution • Gibbs-Helmholtz equation (9.39) • For the pure component (9.40) (9.41) 25 9.6 The Properties of Raoultian Ideal Solutions (iii) The Heat of Formation of an Ideal Solution (9.42) (9.43) 26 9.6 The Properties of Raoultian Ideal Solutions (iv) The Entropy of Formation of an Ideal Solution Eq. (9.44) shows that the entropy of formation of an ideal binary solution is independent of temperature (9.44) 27 9.6 The Properties of Raoultian Ideal Solutions (v) The Entropy of Formation of an Ideal Solution (4.17) 28 9.6 The Properties of Raoultian Ideal Solutions (vi) The Entropy of Formation of an Ideal Solution (9.45) 29 9.6 The Properties of Raoultian Ideal Solutions (vii) The Entropy of Formation of an Ideal Solution 30.
Recommended publications
  • The Acidity of Atmospheric Particles and Clouds Havala O
    The Acidity of Atmospheric Particles and Clouds Havala O. T. Pye1, Athanasios Nenes2,3, Becky Alexander4, Andrew P. Ault5, Mary C. Barth6, Simon L. Clegg7, Jeffrey L. Collett, Jr.8, Kathleen M. Fahey1, Christopher J. Hennigan9, Hartmut Herrmann10, Maria Kanakidou11, James T. Kelly12, I-Ting Ku8, V. Faye McNeill13, Nicole Riemer14, Thomas 5 Schaefer10, Guoliang Shi15, Andreas Tilgner10, John T. Walker1, Tao Wang16, Rodney Weber17, Jia Xing18, Rahul A. Zaveri19, Andreas Zuend20 1Office of Research and Development, U.S. Environmental Protection Agency, Research Triangle Park, NC, 27711, USA 2School of Architecture, Civil and Environmental Engineering, Ecole Polytechnique Fédérale de Lausanne, Lausanne, CH- 1015, Switzerland 10 3Institute for Chemical Engineering Sciences, Foundation for Research and Technology Hellas, Patras, GR-26504, Greece 4Department of Atmospheric Science, University of Washington, Seattle, WA, 98195, USA 5Department of Chemistry, University of Michigan, Ann Arbor, MI, 48109-1055, USA 6National Center for Atmospheric Research, Boulder, CO, 80307, USA 7School of Environmental Sciences, University of East Anglia, Norwich NR4 7TJ, UK 15 8Department of Atmospheric Science, Colorado State University, Fort Collins, CO, 80523, USA 9Department of Chemical, Biochemical, and Environmental Engineering, University of Maryland Baltimore County, Baltimore, MD, 21250, USA 10Leibniz Institute for Tropospheric Research (TROPOS), Atmospheric Chemistry Department (ACD), Leipzig, 04318, Germany 20 11Department of Chemistry, University
    [Show full text]
  • Solution Is a Homogeneous Mixture of Two Or More Substances in Same Or Different Physical Phases. the Substances Forming The
    CLASS NOTES Class:12 Topic: Solutions Subject: Chemistry Solution is a homogeneous mixture of two or more substances in same or different physical phases. The substances forming the solution are called components of the solution. On the basis of number of components a solution of two components is called binary solution. Solute and Solvent In a binary solution, solvent is the component which is present in large quantity while the other component is known as solute. Classification of Solutions Solubility The maximum amount of a solute that can be dissolved in a given amount of solvent (generally 100 g) at a given temperature is termed as its solubility at that temperature. The solubility of a solute in a liquid depends upon the following factors: (i) Nature of the solute (ii) Nature of the solvent (iii) Temperature of the solution (iv) Pressure (in case of gases) Henry’s Law The most commonly used form of Henry’s law states “the partial pressure (P) of the gas in vapour phase is proportional to the mole fraction (x) of the gas in the solution” and is expressed as p = KH . x Greater the value of KH, higher the solubility of the gas. The value of KH decreases with increase in the temperature. Thus, aquatic species are more comfortable in cold water [more dissolved O2] rather than Warm water. Applications 1. In manufacture of soft drinks and soda water, CO2 is passed at high pressure to increase its solubility. 2. To minimise the painful effects (bends) accompanying the decompression of deep sea divers. O2 diluted with less soluble.
    [Show full text]
  • Chaotic Temperatures Vs Coefficients of Thermodynamic Activity: the Advantage of the Method of Chemical Dynamics
    CHAOTIC TEMPERATURES VS COEFFICIENTS OF THERMODYNAMIC ACTIVITY: THE ADVANTAGE OF THE METHOD OF CHEMICAL DYNAMICS B. Zilbergleyt Bank One, IT Department, Chicago E-mail: [email protected] ABSTRACT. The article compares traditional coefficients of thermodynamic activity as a parameter related to individual chemical species to newly introduced reduced chaotic temperatures as system characteristics, both regarding their usage in thermodynamic simulation of open chemical systems. Logical and mathematical backgrounds of both approaches are discussed. It is shown that usage of reduced chaotic temperatures and the Method of Chemical Dynamics to calculate chemical and phase composition in open chemical systems is much less costly, easier to perform and potentially leads to better precision. PROBABILISTIC MODEL OF COMPLEX CHEMICAL EQUILIBRIUM. It is well known how easily the Guldberg-Waage’s equation can be derived from the probabilistic considerations. Being based on the particle collisions, typical for the reactions in gases, it states that chance of the reaction to happen is proportional to joint probability P(A) of reactant particles to occur simultaneously at the same point of the reaction space. This probability merely equals to product of concentrations of the colliding particles. If multiplied by the rate constant it defines the reaction rate. When the rates of the forward and the reverse reactions are equal then the state of equilibrium exists. Less known is the fact that the above derivation is valid only in the case when no one of reactants can be consumed in any other collision with different outcome than A. Chemical system with only one type of collision represents isolated by the reactants (more traditionally referred to as closed) is a simple chemical system: one type of collision – one outcome.
    [Show full text]
  • Physical Chemistry
    Subject Chemistry Paper No and Title 10, Physical Chemistry- III (Classical Thermodynamics, Non-Equilibrium Thermodynamics, Surface chemistry, Fast kinetics) Module No and Title 10, Free energy functions and Partial molar properties Module Tag CHE_P10_M10 CHEMISTRY Paper No. 10: Physical Chemistry- III (Classical Thermodynamics, Non-Equilibrium Thermodynamics, Surface chemistry, Fast kinetics) Module No. 10: Free energy functions and Partial molar properties TABLE OF CONTENTS 1. Learning outcomes 2. Introduction 3. Free energy functions 4. The effect of temperature and pressure on free energy 5. Maxwell’s Relations 6. Gibbs-Helmholtz equation 7. Partial molar properties 7.1 Partial molar volume 7.2 Partial molar Gibb’s free energy 8. Question 9. Summary CHEMISTRY Paper No. 10: Physical Chemistry- III (Classical Thermodynamics, Non-Equilibrium Thermodynamics, Surface chemistry, Fast kinetics) Module No. 10: Free energy functions and Partial molar properties 1. Learning outcomes After studying this module you shall be able to: Know about free energy functions i.e. Gibb’s free energy and work function Know the dependence of Gibbs free energy on temperature and pressure Learn about Gibb’s Helmholtz equation Learn different Maxwell relations Derive Gibb’s Duhem equation Determine partial molar volume through intercept method 2. Introduction Thermodynamics is used to determine the feasibility of the reaction, that is , whether the process is spontaneous or not. It is used to predict the direction in which the process will be spontaneous. Sign of internal energy alone cannot determine the spontaneity of a reaction. The concept of entropy was introduced in second law of thermodynamics. Whenever a process occurs spontaneously, then it is considered as an irreversible process.
    [Show full text]
  • Chemical Equilibrium As Balance of the Thermodynamic Forces
    Chemical Equilibrium as Balance of the Thermodynamic Forces B. Zilbergleyt, System Dynamics Research Foundation, Chicago, USA, E-mail: [email protected] ABSTRACT. The article sets forth comprehensive basics of thermodynamics of chemical equilibrium as balance of the thermodynamic forces. Based on the linear equations of irreversible thermodynamics, De Donder definition of the thermodynamic force, and Le Chatelier’s principle, our new theory of chemical equilibrium offers an explicit account for multiple chemical interactions within the system. Basic relations between energetic characteristics of chemical transformations and reaction extents are based on the idea of chemical equilibrium as balance between internal and external thermodynamic forces, which is presented in the form of a logistic equation. This equation contains only one new parameter, reflecting the external impact on the chemical system and the system’s resistance to potential changes. Solutions to the basic equation at isothermic-isobaric conditions define the domain of states of the chemical system, including four distinctive areas from true equilibrium to true chaos. The new theory is derived exclusively from the currently recognized ideas of chemical thermodynamics and covers both thermodynamics, equilibrium and non-equilibrium in a unique concept, bringing new opportunities for understanding and practical treatment of complex chemical systems. Among new features one should mention analysis of the system domain of states and the area limits, and a more accurate calculation of the equilibrium compositions. INTRODUCTION. Contemporary chemical thermodynamics is torn apart applying different concepts to traditional isolated systems with true thermodynamic equilibriumi and to open systems with self-organization, loosely described as “far-from-equilibrium” area.
    [Show full text]
  • Thermodynamic Studies of the Fe-Pt System and “Feo”-Containing Slags for Application Towards Ladle Refining
    Thermodynamic Studies of the Fe-Pt System and “FeO”-Containing Slags for Application Towards Ladle Refining Patrik Fredriksson Doctoral Dissertation Stockholm 2003 Royal Institute of Technology Department of Material Science and Engineering Division of Metallurgy Akademisk avhandling som med tillstånd av Kungliga Tekniska Högskolan i Stockholm, framlägges för offentlig granskning för avläggande av Teknologie doktorsexamen, fredagen den 7 November 2003, kl. 10.00 i Kollegiesalen, Administrationsbyggnaden, Kungliga Tekniska Högskolan, Valhallavägen 79 Stockholm ISRN KTH/MSE--03/36--SE+THMETU/AVH ISBN 91-7283-592-3 To Anna ii Abstract In the present work, the thermodynamic activites of iron oxide, denoted as “FeO” in the slag systems Al2O3-“FeO”, CaO-“FeO”, “FeO”-SiO2, Al2O3-“FeO”-SiO2, CaO- “FeO”-SiO2 and “FeO”-MgO-SiO2 were investigated by employing the gas equilibration technique at steelmaking temperatures. The strategy was to expose the molten slag mixtures kept in platinum crucibles for an oxygen potential, determined by a CO/CO2-ratio. A part of the iron reduced from the “FeO” in the slag phase was dissolved into the Pt crucible. In order to obtain the activites of “FeO”, chemical analysis of the quenched slag samples together with thermodynamic information of the binary metallic system Fe-Pt is required. Careful experimental work was carried out by employing a solid-state galvanic cell technique as well as calorimetric measurements in the temperature ranges of 1073-1273 K and 300-1988 K respectively. The outcome of these experiments was incorporated along with previous studies into a CALPHAD-type of thermodynamic assessment performed with the Thermo-Calc™ software. The proposed equilibrium diagram enabled extrapolation to higher temperatures.
    [Show full text]
  • Simple Mixtures
    Simple mixtures Before dealing with chemical reactions, here we consider mixtures of substances that do not react together. At this stage we deal mainly with binary mixtures (mixtures of two components, A and B). We therefore often be able to simplify equations using the relation xA + xB = 1. A restriction in this chapter – we consider mainly non-electrolyte solutions – the solute is not present as ions. The thermodynamic description of mixtures We already considered the partial pressure – the contribution of one component to the total pressure, when we were dealing with the properties of gas mixtures. Here we introduce other analogous partial properties. Partial molar quantities: describe the contribution (per mole) that a substance makes to an overall property of mixture. The partial molar volume, VJ – the contribution J makes to the total volume of a mixture. Although 1 mol of a substance has a characteristic volume when it is pure, 1 mol of a substance can make different contributions to the total volume of a mixture because molecules pack together in different ways in the pure substances and in mixtures. Imagine a huge volume of pure water. When a further 1 3 mol H2O is added, the volume increases by 18 cm . When we add 1 mol H2O to a huge volume of pure ethanol, the volume increases by only 14 cm3. 18 cm3 – the volume occupied per mole of water molecules in pure water. 14 cm3 – the volume occupied per mole of water molecules in virtually pure ethanol. The partial molar volume of water in pure water is 18 cm3 and the partial molar volume of water in pure ethanol is 14 cm3 – there is so much ethanol present that each H2O molecule is surrounded by ethanol molecules and the packing of the molecules results in the water molecules occupying only 14 cm3.
    [Show full text]
  • Measurement of Carbon Thermodynamic Activity In
    J - carbon flow through sensor membrane 83 MEASUREMENT OF CARBON THERMODYNAMIC 2 ACTIVITY IN SODIUM g , cm" , min" ; t - time, s; GJT - sodium flow rate irr/hour, L/hour; F.A, KOZLOV, Yu.I. ZAGORULKO, Yu.P. KOVALEV, H_ - sensor signal, vol. % CH ; V.V. ALEKSEEV g 4 Institute of Physics and Power Engineering, Gr - decarburizing gas flow rate through sensor ; Obninsk, o Union of Soviet Socialist Republics T,t - t emperature. C; t - sensor t emperature; Gg - sodium flow rate through sensor. INTRODUCTION ABSTRACT Continuous detection of carbon thermodynaraic activity in The report presents the brief outline on system of carbon sodium coolant of energy installations with fast neutron reac- activity detecting system in sodium(SCD), operating on the tors presupposes conducting the following main functions; : carbon - permeable membrane, of the methods and the results of - Control of carburization sodium potential with reference to testing it under the experimental circulating loop conditions. construction materials; The results of carbon activity sensor calibration with the u,s,e - Control of sodium coolant accidental contamination by carbon- of equilibrium samples of XI8H9, Fe -8Ni, Pe ~12Mn materials bearing impurities, for example, as a result of oil leakage from are listed. The behawiour of carbon activity sensor signals in a centrifuginal pump cooling system. sogium under various transitional conditions and hydrodynamic Performing these functions under the monisothermal loop condi- perturbation in the circulating loop, containing carbon bearing tions has specific features which on the one hand depend on impurities in the sodium flow and their deposits on the surfa- construction and operating parameters of detectors and on the ces flushed by sodium, are described.
    [Show full text]
  • Chapter 9 Ideal and Real Solutions
    2/26/2016 CHAPTER 9 IDEAL AND REAL SOLUTIONS • Raoult’s law: ideal solution • Henry’s law: real solution • Activity: correlation with chemical potential and chemical equilibrium Ideal Solution • Raoult’s law: The partial pressure (Pi) of each component in a solution is directly proportional to the vapor pressure of the corresponding pure substance (Pi*) and that the proportionality constant is the mole fraction (xi) of the component in the liquid • Ideal solution • any liquid that obeys Raoult’s law • In a binary liquid, A-A, A-B, and B-B interactions are equally strong 1 2/26/2016 Chemical Potential of a Component in the Gas and Solution Phases • If the liquid and vapor phases of a solution are in equilibrium • For a pure liquid, Ideal Solution • ∆ ∑ Similar to ideal gas mixing • ∆ ∑ 2 2/26/2016 Example 9.2 • An ideal solution is made from 5 mole of benzene and 3.25 mole of toluene. (a) Calculate Gmixing and Smixing at 298 K and 1 bar. (b) Is mixing a spontaneous process? ∆ ∆ Ideal Solution Model for Binary Solutions • Both components obey Rault’s law • Mole fractions in the vapor phase (yi) Benzene + DCE 3 2/26/2016 Ideal Solution Mole fraction in the vapor phase Variation of Total Pressure with x and y 4 2/26/2016 Average Composition (z) • , , , , ,, • In the liquid phase, • In the vapor phase, za x b yb x c yc Phase Rule • In a binary solution, F = C – p + 2 = 4 – p, as C = 2 5 2/26/2016 Example 9.3 • An ideal solution of 5 mole of benzene and 3.25 mole of toluene is placed in a piston and cylinder assembly.
    [Show full text]
  • THE CONCEPT of ELECTRON ACTIVITY and ITS RELATION to REDOX POTENTIALS in AQUEOUS GEOCHEMICAL SYSTEMS by Donald C
    THE CONCEPT OF ELECTRON ACTIVITY AND ITS RELATION TO REDOX POTENTIALS IN AQUEOUS GEOCHEMICAL SYSTEMS by Donald C. Thorstenson U.S. GEOLOGICAL SURVEY Open-File Report 84 072 1984 UNITED STATES DEPARTMENT OF THE INTERIOR WILLIAM T. CLARK, Secretary GEOLOGICAL SURVEY Dallas L. Peck, Director For additional information Copies of this report may be write to: purchased from: Regional Research Hydrologist U.S. Geological Survey U.S. Geological Survey Western Distribution Branch Water Resources Division Open-File Services Section 432 National Center Box 25425, Federal Center Reston, Virginia 22092 Denver, Colorado 80225 ERRATA: (p. 1) 1. Equation (2), p. 3, should read: n 2.30RT 1 n 2.30RT , x = Ej? + _____ log__= E° + _____pH . (2) 2. Table 1, p. 6, entry 5, should read: In pure water, p e - 6.9; 3. Line 3, paragraph 3, p. 10 should read: As Fe^+ / aa \ is converted to Fe ( aa ) via equation (15) to 4. Equation (22), p. 13, should read: a n p - anya n+ e (aq) UA (aq) K = . (22) 5. Equation (38), p. 18, should read: F -log ae - = _______ Eh + . (38) ( acl) 2.303RT 2.303RT 6. Equation (52), p. 23, should read: ae- (aq) 7. Equation (53), p. 23, should read: pe s +6.9 and Eh s + 0.41 volt. (53) 8. Equation (54c), p. 23, should read: nu-'e ~ 10 -55.5 (aq) ERRATA: (p. 2) 9. The second line from the bottom, p. 28, should read: ....... (a state that has been maintained for * 105 years based on .... 10. The heading of Table 2, p.
    [Show full text]
  • Fugacity Nov 2 2011.Pdf
    Fugacity - Wikipedia, the free encyclopedia 頁 1 / 5 Fugacity From Wikipedia, the free encyclopedia In chemical thermodynamics, the fugacity (f) of a real gas is an effective pressure which replaces the true mechanical pressure in accurate chemical equilibrium calculations. It is equal to the pressure of an ideal gas which has the same chemical potential as the real gas. For example, [1] nitrogen gas (N2) at 0°C and a pressure of 100 atm has a fugacity of 97.03 atm. This means that the chemical potential of real nitrogen at a pressure of 100 atm has the value which ideal nitrogen would have at a pressure of 97.03 atm. Fugacities are determined experimentally or estimated for various models such as a Van der Waals gas that are closer to reality than an ideal gas. The ideal gas pressure and fugacity are related through the dimensionless fugacity coefficient .[2] For nitrogen at 100 atm, the fugacity coefficient is 97.03 atm / 100 atm = 0.9703. For an ideal gas, fugacity and pressure are equal so is 1. The fugacity is closely related to the thermodynamic activity. For a gas, the activity is simply the fugacity divided by a reference pressure to give a dimensionless quantity. This reference pressure is called the standard state and normally chosen as 1 atmosphere or 1 bar, Again using nitrogen at 100 atm as an example, since the fugacity is 97.03 atm, the activity is just 97.03 with no units. Accurate calculations of chemical equilibrium for real gases should use the fugacity rather than the pressure.
    [Show full text]
  • New Thermodynamic Activity-Based Approach Allows Predicting The
    www.nature.com/scientificreports OPEN New thermodynamic activity‑based approach allows predicting the feasibility of glycolysis Thorsten Greinert1, Kristina Vogel2, Thomas Maskow2 & Christoph Held1* Thermodynamic feasibility analyses help evaluating the feasibility of metabolic pathways. This is an important information used to develop new biotechnological processes and to understand metabolic processes in cells. However, literature standard data are uncertain for most biochemical reactions yielding wrong statements concerning their feasibility. In this article we present activity‑based equilibrium constants for all the ten glycolytic reactions, accompanied by the standard reaction data (standard Gibbs energy of reaction and standard enthalpy of reaction). We further developed a thermodynamic activity‑based approach that allows to correctly determine the feasibility of glycolysis under diferent chosen conditions. The results show for the frst time that the feasibility of glycolysis can be explained by thermodynamics only if (1) correct standard data are used and if (2) the conditions in the cell at non‑equilibrium states are accounted for in the analyses. The results here will help to determine the feasibility of other metabolisms and to understand metabolic processes in cells in the future. Biotechnological routes ofer several advantages over classical chemical routes to produce chemicals, such as higher reaction selectivity and milder reaction conditions, yielding an overall more sustainable processes 1. Fur- thermore, such routes access a world full of new syntheses protocols using reactions that require the use of an enzyme or multiple enzymes in a complete metabolic pathway. However, fnding such new syntheses routes is generally expensive due to high experimental efort. So-called thermodynamic feasibility analyses (TFA) help to determine whether a metabolic pathway is generally feasible or not from thermodynamic point-of-view.
    [Show full text]