C H Ap Ter 10 / R U Ssian B Ar

10 bar / Russian 10 Chapter Chapter Russian bar Written by Glen Stewart Contributors: Juan-Carlos Benitez Lucy Francis-Litton Juliette Hardy-Donaldson Sainbayar Janchividorj Darek Karczewski Sylvain Rainville André St-Jean Jarek Wojciechowski This document is published by the FEDEC European Federation of Professional Circus Schools. It is free of charges and can not be sold. 10 RUSSIAN BAR Russian bar Russian Introduction 2 Part 1. Why single bar or triple bar? 3 Part 2. Construction of the bars 4 2.1. Single bar construction 4 2.2. Triple bar construction 5 Part 3. Safety 11 3.1. Communication 11 3.2. Lunging 11 3.3. Spotting. 13 Part 4. Basics of single bar 15 4.1. Handstands on the Bar 20 4.2. Suggested skill progression for single bar 21 Part 5. Basics of triple bar 22 5.1. Bases’ posture and position. 22 5.2. The 4 tasks / stages for the base: 23 5.3. Flyer training 26 Mounting the bar. 27 Foot positioning for the flyer. 28 Initiating the jump. 29 5.4. Suggested skill progression for triple bar 30 Part 6. Trampoline Training 31 Getting the height 31 Rotation 31 Arms 31 Training habits and pointers 31 Body position on landing 32 This document is published by the FEDEC – European Federation of Professional Circus Schools. It is free of charges and can not be sold. 1 10 Introduction Russian bar Russian The purpose of this manual is to be an introduction to Russian bar and to help with the fundamental elements of Russian bar technique. The intention is that with the help of this manual, teachers and students will be able to construct their own bar and safely begin training bar technique. The manual will cover some basics of both single and triple bar work. There are alternatives and variations to the techniques and equipment discussed in this manual and over time students and teachers may discover their own preferences and adjust their practice accordingly. Trampoline is an essential learning tool for the development of flyers’ acrobatic skills. It is advised that the teacher and flyers have a sound knowledge of trampoline technique. This manual will give a limited introduction to how the trampoline can and should be used but further knowledge is essential to become proficient as a Russian bar teacher or performer. 2 This document is published by the FEDEC – European Federation of Professional Circus Schools. It is free of charges and can not be sold. 10 Part 1. / Why single bar or triple bar? Russian bar Russian There are some tricks that are much better suited to the single bar. Skills involving handstands for example, are easier on the single bar as the flyer can grip a single rounded bar better than a flat wide bar. The flex and length of a triple bar creates too much power for handstand tricks and could be dangerous for the flyer trying to land in handstand. On the other hand the potential power of the triple bar allows the flyer to execute and land a much higher level of acrobatic skills. It takes time for the bases to understand how to balance the flyer efficiently and equally as much time for the flyer to stop fighting for balance and give the responsibility over to the bases. The single bar is an excellent learning tool for the basic control of balance for the bases and flyers and it is recommended that students spend time working on the single bar as preparation for working on the triple bar. This document is published by the FEDEC – European Federation of Professional Circus Schools. It is free of charges and can not be sold. 3 10 Part 2. / Construction of the bars Russian bar Russian 2.1. Single bar construction A single Russian bar is one fibreglass pole. Second-hand Pole vaulting poles are widely used. Fibreglass, unlike other materials, is not badly affected by heat, cold or weather. As long as they are not cracked or weakened in some way, they should last a conside- rable time. Typically lengths vary between 2.5 and 3.5 metres long, with a diameter of 45-50 mm. The poles that are used for single bars are slightly larger in diameter but shorter than those used for triple bars. You need to consider the weight of the flyer when selecting a pole. A more flexible pole is used for lighter flyers and a less flexible pole for those that are heavier. Pole vaulting poles are made with a slight curve. The correct way up should be with the lowest point of the curve closest to the floor (like a smile). Once you have indentified the way the pole bends, you can put a small mark with tape or pen to indicate the top side of the pole at each end. This will help the bases to identify which way to hold the bar. The central 1 to 2 meters of the pole is taped (e.g. with physiotherapy tape) for grip and also at each end (where the bases will hold it). The very centre of the pole should be marked with a clearly visible piece of tape. You will need to try different bars to find one with the amount of flex that suits the group. However, the amount of flex of a single bar is not as important as with triple bar work as the tricks performed on a single bar tend to be less dynamic. If the bar flexes too much one possible solution is to slide a smaller diameter pole inside the existing one. 2.2. Triple bar construction A triple bar is made up from 3 fibreglass poles bound together to make a flat plank. First check your poles for cracks or general damage. By tapping the poles lightly with a metal object you will hear by a change in sound if there is a crack. The poles will have a slight natural curve. Place the poles together in such a way so that they all naturally curve downwards. 4 This document is published by the FEDEC – European Federation of Professional Circus Schools. It is free of charges and can not be sold. 10 Part 2. / Construction of the bars Russian bar Russian There is no set length for a Russian bar and individual troupes will need to discover what length they prefer. Typically, Russian bars are around 4 – 4.5 meters but it may vary beyond those limits. What is important is that the length of the bar suits the weight of the flyer. A heavier flyer will need a shorter and more rigid bar. Conversely, a lighter flyer will need a much more flexible bar or they will not have the weight needed to bend the bar and generate power from it. Some poles will have more or less flexion than other poles. If one pole is more flexible than the other two, place it in the middle of the three to ensure that both edges of the bar act in the same way and give the pole rigidity. A more flexible pole on the outside will cause the Russian bar to twist to that side. More flexible bars will make the job of the bases easier as it spreads the load over a longer time. Obviously the bar is too soft if the bar flexes excessively and touches the ground under the flyer at the bottom of the tempo. Step 1 When you have the poles aligned and at the same lengths, use tape (e.g. physiotherapy tape) to hold the poles together. Place tape in three evenly spaced places along the pole, one at each end and one in the centre. Avoid pulling the tape too tight to avoid twisting the poles. These three strips of tape are just to hold the poles in the correct position. Step 2 Apply soft setting silicon sealer between the poles. This will fix the poles in place but will not affect the flexibility of the Russian bar. After applying the silicon from the tube, use a wet finger to push it into the gap. This document is published by the FEDEC – European Federation of Professional Circus Schools. It is free of charges and can not be sold. 5 10 Part 2. / Construction of the bars Russian bar Russian In the future, if you want to replace or re-use any of the poles, the silicon is easily re- moved. Apply the silicon to both the top and undersides of the poles. Once the silicon has been applied put two or three more binding strips of tape along the length of the pole. Again, this is just to hold the poles in the correct place while you continue to work. Step 3 At each end of the bar on the underside attach as small section of wood (approx. 3cm x 3cm x the width of the Russian bar). Fix it with bolts that go through the wood and the poles. It is advisable to put wooden stoppers into the end of the poles so you when you tighten the nuts of the bolts you don’t crush and damage the fibreglass. Step 4 To make a flat landing area on the bar a thin and flexible length of board is attached to the top side of the bar in the centre. The base of a snowboard is good for this but any thin flexible wood that will not restrict the flex of the bar will work. The board ensures that the contours of the poles cannot be felt by the flyer and provides a stable landing platform.

Load more