Prusaprinters
Total Page:16
File Type:pdf, Size:1020Kb
BamBam Rubble 3D MODEL ONLY reddadsteve VIEW IN BROWSER updated 11. 8. 2020 | published 11. 8. 2020 Summary BamBam, from the Flintstones cartoon show by Hanna-Barbera. The Flintstones cartoon takes place in a romanticized Stone Age setting, depicting the lives of the Flintstone family and their best friends and neighbors the Rubbles. BamBam is the adopted son of Betty Rubble and Barney Rubble after they found him left on their doorstep No supports are required. If you have the proper filament colors, no painting is needed. The model is 155mm tall after assembly. Enjoy, and I hope you have a "Yaba Daba Do" time printing this! Toys & Games > Action Figures & Statues flintstones comics cartoon baby Print Settings Printer: FlashForge Creator X Rafts: Doesn't Matter Supports: No Resolution: .2mm Infill: 10% Notes: See below for helpful printing and building notes Building the model Colors Black: eye_blacks (contains two pieces) eyebrow_left eyebrow_right mouth .. Skin or Beige: head body_left body_right legs (contains two pieces) .. Orange: hat pants .. Light Brown: base club_top club_bottom .. Dark brown: strap .. White: hair_top hair_bottom bone_left bone_right eye_whites (contains two pieces) .. Any color (hidden pieces): pins (contains four pieces) Printing and assembly tips 1-As with most of my models, no supports are required. 2-Be sure to clean any first layer squish if you have any problem joining parts. The parts should fit nicely when printed cleanly. 3-There are a number of very small pieces which can easily get lost if you are as clumsy as I am. It's a good Idea to simply print extra pieces of the small parts since they are fast to print. 4-Use your discretion for rafts/brims on the bone pieces since they have smallish bases and are top heavy. 5-On a personal note, my wife still says Pebbles looks much cuter than BamBam! .. Assembly tips: 1-For ease of assembly, I suggest inserting the eye_whites into the eye_blacks with the smooth side facing out but either way works. 4-The head snaps into the hair_bottom with a bit of pressure. Be sure to align and push the head completely up and into the hair_bottom for a complete fit. I did not use any glue on this part. 3-The bones fit into the slight indents in the strap piece and the larger portion of the bone simply rests on the pants. Look carefully at the bone, it could accidentally be positioned upside down. Left/right bones pieces are ever so slightly different and could be switched if you get them confused. 4- I use a tacky glue to put my models together, E6000, so I have plenty of time to position them correctly. The body, strap and pants are all glued together so if you are using a fast drying glue be sure to fully test fit the pieces and decide the best order of gluing them. Your feedback will be appreciated. 5-A general note, I struggled with this model in order to create it without supports. Therefore I made some concessions to the iconic pose that the character normally takes. In addition, there are some very small design flaws that I simply could not get around. I am still happy with the model and again, your feedback is most welcome. 5-Refer to the assembly diagram for putting the model together. The model is meant to be glued. Model Files (.stl, .3mf, .obj, .amf) DOWNLOAD ALL FILES eye_whites.stl 14.5 KB updated 11. 8. 2020 body_right.stl 1.3 MB updated 11. 8. 2020 club_bottom.stl 117.6 KB updated 11. 8. 2020 legs.stl 1.4 MB updated 11. 8. 2020 body_left.stl 1.0 MB updated 11. 8. 2020 hat.stl 465.1 KB updated 11. 8. 2020 hair_top.stl 755.0 KB updated 11. 8. 2020 eyebrow_left.stl 10.7 KB updated 11. 8. 2020 mouth.stl 34.1 KB updated 11. 8. 2020 head.stl 2.6 MB updated 11. 8. 2020 club_top.stl 17.7 KB updated 11. 8. 2020 bone_left.stl 332.6 KB updated 11. 8. 2020 bone_right.stl 324.1 KB updated 11. 8. 2020 eye_blacks.stl 238.6 KB updated 11. 8. 2020 base.stl 236.5 KB updated 11. 8. 2020 strap.stl 428.0 KB updated 11. 8. 2020 pants.stl 2.3 MB updated 11. 8. 2020 eyebrow_right.stl 7.5 KB updated 11. 8. 2020 pins.stl 2.4 KB updated 11. 8. 2020 hair_bottom.stl 914.5 KB updated 11. 8. 2020 Find source .stl files on Thingiverse.com The Author has not uploaded any print files. Try to search in User print files section or generate and upload your own. License This work is licensed under a Creative Commons (4.0 International License) Attribution—Noncommercial—Share Alike ✖ | Sharing without ATTRIBUTION ✔ | Remix Culture allowed ✖ | Commercial Use ✖ | Free Cultural Works ✖ | Meets Open Definition .