Configuration Sheets

PRIMERGY RX600 S3 Configuration Sheets

About this manual

A Configuration Sheets of Hardware Use this form to record the hardware configuration and various settings of your server.

B Configuration Sheets of BIOS Setup Utility Parameters Use this form to record the settings of the BIOS Setup Utility.

C Table of System Resource Management The I/O port address that can be selected with various expansion cards is the following tables.

D Design Sheet of the RAID Configuration Use this form to record the definitions of the disk groups (or the physical packs) and the logical drives in the RAID configuration (array configuration).

E Design Sheet Use this form to record the software settings.

F Accident Sheet Use this form to record any failures that occur in your server.

1 Product Names

The following expressions and abbreviations are used to describe the product names used in this manual.

Product names Expressions and abbreviations PRIMERGY RX600 S3 This server or the server

Windows Server 2003 R2, Windows Microsoft® Windows Server® 2003 R2, Standard Edition Standard Edition 2003 Windows Server 2003 R2, Microsoft® Windows Server® 2003 R2, Enterprise Edition Enterprise Edition

Windows Server 2003 , Microsoft® Windows Server® 2003 , Enterprise Edition Enterprise Edition

Windows Server 2003, Standard Microsoft® Windows Server® 2003, Standard Edition Edition

Windows Server 2003 R2, Microsoft® Windows Server® 2003 R2, Standard x64 Edition Standard x64 Edition

Windows Server 2003 R2, Microsoft® Windows Server® 2003 R2 , Enterprise x64 Edition Enterprise x64 Edition

Windows Server 2003, Standard Microsoft® Windows Server® 2003, Standard x64 Edition x64 Edition

Windows Server 2003 , Microsoft® Windows Server® 2003 , Enterprise x64 Edition Enterprise x64 Edition Windows Microsoft® Windows® 2000 Server Windows 2000 Server 2000

Microsoft® Windows® 2000 Advanced Server Windows 2000 Advanced Server

Microsoft® Windows Server® 2003 Service Pack SP

Microsoft® Windows® 2000 Service Pack

■Trademarks Microsoft, Windows, MS, Windows Server are registered trademarks of the Microsoft Corporation in the USA and other countries. Intel, Xeon, Celeron and Pentium are registered trademarks or trademarks of Intel Corporation or its subsidiaries in the USA and other countries. All other hardware and software names used are trademarks or registered trademarks of their respective manufacturers. Other product names are copyrights of their respective manufacturers.

2 PRIMERGY RX600 S3 Configuration Sheets

Contents A Configuration Sheets of Hardware ...... 4 B Configuration Sheets of BIOS Setup Utility Parameters ...... 6 B.1 Parameters in the Main Menu ...... 6 B.2 Parameters in the Processor Menu ...... 7 B.3 Parameters in the Memory Menu ...... 8 B.4 Parameters in the Devices Menu ...... 12 B.5 Parameters in the Server Menu ...... 14 B.6 Parameters in the Security Menu ...... 17 C Table of System Resource Management ...... 18 D Design Sheet of the RAID configuration ...... 19 D.1 For RX600 S3 Onboard SCSI Array Controller (MegaRAID SCSI 320-2E) . . . 19 D.2 For PG-142E3 (MegaRAID SCSI 320-2) ...... 21 E Design Sheet ...... 23 F.1 RAID/Disk Wizard ...... 23 F.2 OS Wizard (Windows 2003 Install Wizard) ...... 24 F.3 OS Wizard (Windows 2000 Install Wizard) ...... 31 F.4 Application Wizard ...... 37 F Accident Sheet ...... 38

3 A Configuration Sheets of Hardware

Ａ Configuration Sheets of Hardware

Use this form to record the hardware configuration and various settings of your server. Put a check mark in parentheses of your server settings.

■3.5-inch Internal Options Installation 3.5 inch internal option Installed position 10,000rpm 15,000rpm Bay 1 ( ) 73.4GB ( ) 146.8GB ( ) 300GB ( ) 73.4GB ( ) 146.8GB Bay 2 ( ) 73.4GB ( ) 146.8GB ( ) 300GB ( ) 73.4GB ( ) 146.8GB Bay 3 ( ) 73.4GB ( ) 146.8GB ( ) 300GB ( ) 73.4GB ( ) 146.8GB Bay 4 ( ) 73.4GB ( ) 146.8GB ( ) 300GB ( ) 73.4GB ( ) 146.8GB Bay 5 ( ) 73.4GB ( ) 146.8GB ( ) 300GB ( ) 73.4GB ( ) 146.8GB

■5-inch Internal Options

Installation 5 inch internal option (Product ID) SCSI ID ( ) Internal DAT72 unit （PG-DT5041） - ( ) Internal VXA2 unit （PG-VX201） 5 ( ) Internal LTO2 unit （PG-LT201）

Low-profile installation 5 inch bay ( ) Internal CD-ROM drive unit (Standard) ( ) Internal DVD-RAM drive unit （PG-DVA103）

4 PRIMERGY RX600 S3 Configuration Sheets

■RAM Modules Installation slot Installation RAM module

( ) 1GB ( ) 2GB Slot 1A ( ) 4GB Memory Bank 1 ( ) 1GB ( ) 2GB Slot 1B ( ) 4GB Memory Board A ( ) 1GB ( ) 2GB Slot 2A ( ) 4GB Memory Bank 2 ( ) 1GB ( ) 2GB Slot 2B ( ) 4GB

( ) 1GB ( ) 2GB Slot 1A ( ) 4GB Memory Bank 1 ( ) 1GB ( ) 2GB Slot 1B ( ) 4GB Memory Board B ( ) 1GB ( ) 2GB Slot 2A ( ) 4GB Memory Bank 2 ( ) 1GB ( ) 2GB Slot 2B ( ) 4GB

( ) 1GB ( ) 2GB Slot 1A ( ) 4GB Memory Bank 1 ( ) 1GB ( ) 2GB Slot 1B ( ) 4GB Memory Board C ( ) 1GB ( ) 2GB Slot 2A ( ) 4GB Memory Bank 2 ( ) 1GB ( ) 2GB Slot 2B ( ) 4GB

( ) 1GB ( ) 2GB Slot 1A ( ) 4GB Memory Bank 1 ( ) 1GB ( ) 2GB Slot 1B ( ) 4GB Memory Board D ( ) 1GB ( ) 2GB Slot 2A ( ) 4GB Memory Bank 2 ( ) 1GB ( ) 2GB Slot 2B ( ) 4GB Install the same memory capacity to Slot A and Slot B of the same memory bank Please put memory from memory bank 1 on memory bank 2 in order of 4GBx2 → 1GBx2 → 2GBx2.

■CPU

Installation CPU Number ( ) Xeon Processor MP 3.66GHz / 1MB ( ) Xeon Processor 7041 3GHz / 2x2MB ( )1 ( )2 ( )3 ( )4 ( ) Xeon Processor 7120M 3GHz / 4MB ( ) Xeon Processor 7140M 3.4GHz / 16MB Same CPU must be installed.

■PCI Cards

PCI slot location Expansion card (Product ID) 1234567 Remote Service Board （PG-RSB105）－－－－－－( ) SCSI array controller card （PG-142E3）－ ( ) －－－( ) ( ) SCSI card（PG-1281）－ ( ) －－－( ) ( ) Fibre Channel Controller （PG-FC202） ( ) － ( ) ( ) ( ) －－ＬＡＮ card （PG-2861） ( ) － ( ) ( ) ( ) －－ＬＡＮ card （PG-1892）－ ( ) －－－( ) ( ) ＬＡＮ card （PG-1882）－ ( ) －－－( ) ( ) ＬＡＮ card （PG-1862）－－－－－( ) ( ) －：Indicates that this item cannot be installed.

5 B Configuration Sheets of BIOS Setup Utility Parameters

Ｂ Configuration Sheets of BIOS Setup Utility Parameters

Use this form to record the settings of the BIOS Setup Utility. If you have not changed the initial value, put a check mark in parentheses of "The initial values have been unchanged". The initial values in the dotted frame can be changed. If you change any setting, put a check mark in parentheses of the ”Setting” column. Keep the values on the gray zones unchanged.

Follow the procedure below to start the BIOS Setup Utility. When the following message appears on the screen during POST, press the [F2] key while the message is displayed. When POST is completed, the Main menu screen appears.

BIOS Setup/ Boot Menu

If the system starts before starting the BIOS Setup Utility, press the [Ctrl] + [Alt] + [Delete] keys simultaneously and restart the system.

Ｂ.１ Parameters in the Main menu

（） The initial values have been unchanged. Item Initial value Setting

Bios Version Version of BIOS System Time: HH:MM:SS Displays/Sets present time. System Date: MM/DD/YYYY Displays/Sets present date.

Hide Diagnostic Messages Disabled ( )Enabled During Boot

POST Error Pause Enabled ( )Disabled

6 PRIMERGY RX600 S3 Configuration Sheets

Ｂ.２ Parameters in the Processor menu

（） The initial values have been unchanged. Item Initial value Setting

Examine and set system Processor parameters

Core Frequency Displays the frequency of installed CPU. Bus Frequency Displays the FSB of installed C PU. Processor Retest Disabled ( )Enabled

Boot Processor Number Processor #1 Displays the boot processor number. > Processor #1 Information Links to the P rocessor #n Information > Processor #2 Information (n:1 to 4) submenu > Processor #3 Information > Processor #4 Information

Hyper-Threading Technology Disabled *1 ( )Enabled Enhanced Intel Speed Step (R) Auto ( )Disabled Technology

Execute Disable Bit Disabled ( )Enabled Hardware Prefetcher Disabled ( )Enabled Adj. Cache Line Prefetch Disabled ( )Enabled Enhanced Halt State Enabled ( )Disabled Intel(R) Virtualization Technology *2 Disabled ( )Enabled Wait For Local Snoop Disabled ( )Enabled Chipset Priority Mode Other ( )Processor/Memory ( )I/O Throughput

*1： The displayed value varies depending on the installed CPUs; with Intel Xeon processor MP 3.66GHz installation, the initial value is Enabled. Do not set this parameter to Enabled in Linux systems with Intel Xeon processor 7041, 7120M, or 7140M installation. *2： Appears only when Intel Xeon processor 7041/Intel Xeon processor 7120M /Intel Xeon processor 7140M (dual core CPU) is installed.

7 B Configuration Sheets of BIOS Setup Utility Parameters

■Processor #n Information (n:1 ～ 4) submenu

Item Initial value Setting

Detailed information for processor #n.

Processor Family Displays the information on the processor family. Maximum Frequency Displays the maximum frequency of installed CPU. Cache Size Displays the cache size of installed CPU.

CPUID Register Displays the CPUID information of installed

Core1 Thread 1 Status Displays the thread information. Thread 1 Health Displays the thread information.

Thread 2 Status Displays the thread information. Thread 2 Heal Displays the thread information.

Core2 *1 Thread 1 Status Displays the thread information. Thread 1 Health Displays the thread information.

Thread 2 Status Displays the thread information. Thread 2 Heal Displays the thread information.

*1： Appears only when Intel Xeon processor 7041/Intel Xeon processor 7120/Intel Xeon processor 7140 (dual core CPU) is installed.

Ｂ.３ Parameters in the Memory Menu

Item Initial value Setting

Examine and set system Memory parameters.

Total Memory Displays the total amount of memory installed. Effective Memory Displays the total amount of memory used on the OS. Memory Boards Installed Displays the memory boards installed. Current Configuration Displays the current memory configuration.

> Configure Memory RAS and Performance Links to Configure System RAS and Performance submenu

> View and Configure Memory Board A Links to View and Configure Memory Board A submenu > View and Configure Memory Board B Links to View and Configure Memory Board B submenu > View and Configure Memory Board C Links to View and Configure Memory Board C submenu > View and Configure Memory Board D Links to View and Configure Memory Board D submenu

8 PRIMERGY RX600 S3 Configuration Sheets

■Configure System RAS and Performance submenu

（） The initial values have been unchanged.

Item Initial value Setting

Hardware Memory Test Enabled ( )Disabled Patrol Scrub Enabled ( )Disabled Retest All System Memory Disabled ( )Enabled Sparing Threshold 15 ( )1～14 RAID Upgrade Gap Disabled ( )512MB ( )1024MB ( )1536MB ( )2048MB ( )2560MB ( )3072MB ( )3584MB ( )4096MB

Desired Memory Configuration Max Performance ( )Max Compatibility ( )Mirror ( )RAID

> View Configuration Details Links to View Configuration Details

Set Memory Hotplug in SRAT table Yes ( )No

■View Configuration Details submenu

Item Initial value Setting

Configuration Displays the current memory configuration. Max Effective Size Displays the maximum effective size of memory. Min Effective Size Displays the size when the maximum size of memory is set to the spare.

Capabilities Configuration Possible Displays availability of selected memory settings. Sparing Displays availability of Hot Spare with the current memory configuration. Hot Replace Displays availability of Hot Replace with the current memory configuration. Hot Add Displays availability of Hot A dd with the current memory configuration. Board Interleave Displays the information on memory board interleave.

9 B Configuration Sheets of BIOS Setup Utility Parameters

■View and Configure Memory Board A submenu

（） The initial values have been unchanged. Item Initial value Setting

Board Status Displays the memory board status. Retest Board Memory Disabled ( )Enabled Reserve Rank for Spare Disabled ( )Enabled

LABEL RANK SIZE STATUS

Displays the memory status. The meanings of the items are as follows.

LABEL: Displays the number of DIMM RANK: Displays the RANK number of DIMM SIZE: Displays the size of DIMM STATUS: Displays the status of DIMM

■View and Configure Memory Board B submenu （） The initial values have been unchanged.

Item Initial value Setting

Board Status Displays the memory board status. Retest Board Memory Disabled ( )Enabled Reserve Rank for Spare Disabled ( )Enabled

LABEL RANK SIZE STATUS

Displays the memory status. The meanings of the items are as follows.

LABEL: Displays the number of DIMM RANK: Displays the RANK number of DIMM SIZE: Displays the size of DIMM STATUS: Displays the status of DIMM

10 PRIMERGY RX600 S3 Configuration Sheets

■View and Configure Memory Board C submenu

（） The initial values have been unchanged. Item Initial value Setting

Board Status Displays the memory board status. Retest Board Memory Disabled ( )Enabled Reserve Rank for Spare Disabled ( )Enabled

LABEL RANK SIZE STATUS

Displays the memory status. The meanings of the items are as follows.

LABEL: Displays the number of DIMM RANK: Displays the RANK number of DIMM SIZE: Displays the size of DIMM STATUS: Displays the status of DIMM

■View and Configure Memory Board D submenu （） The initial values have been unchanged.

Item Initial value Setting

Board Status Displays the memory board status. Retest Board Memory Disabled ( )Enabled Reserve Rank for Spare Disabled ( )Enabled

LABEL RANK SIZE STATUS

Displays the memory status. The meanings of the items are as follows.

LABEL: Displays the number of DIMM RANK: Displays the RANK number of DIMM SIZE: Displays the size of DIMM STATUS: Displays the status of DIMM

11 B Configuration Sheets of BIOS Setup Utility Parameters

Ｂ.４ Parameters in the Devices Menu

（） The initial values have been unchanged.

Item Initial value Setting

Examine and set system parameters for built-in Devices.

> IDE Controller Links to IDE Controller submenu > Mass Storage Links to Mass Storage submenu > LAN Links to LAN submenu > Video Links to Video submenu > USB Links to USB submenu > Serial Ports Links to Serial Ports submenu > PCI Links to PCI submenu

■IDE Controller submenu

（） The initial values have been unchanged.

Item Initial value Setting

Examine and set IDE controller parameters.

Enable Serial ATA Enabled ( )Disabled

Primary Master ICH Serial ATA Controller

■Mass Storage submenu

（） The initial values have been unchanged.

Item Initial value Setting

Examine and set mass storage controller’s parameters.

Enable On-board SCSI Enabled ( )Disabled RAID Activation Key Installed

12 PRIMERGY RX600 S3 Configuration Sheets

■LAN submenu

（） The initial values have been unchanged.

Item Initial value Setting

Examine and set Local Area Network (LAN) parameters.

Enable On-board NIC Enabled ( )Disabled Enable On-board NIC ROM Enabled ( )Disabled

NIC 1 MAC Address Displays the MAC address of the NIC 1 . NIC 2 MAC Address Displays the MAC address of the NIC 2 .

■Video submenu （） The initial values have been unchanged.

Item Initial value Setting

Examine and set Video parameters.

Enable On-board Video Enabled ( )Disabled

■USB submenu （） The initial values have been unchanged.

Item Initial value Setting

Examine and set USB controller parameters.

USB Controller Enable Enabled ( )Disabled USB 2.0 Controller Enabled ( )Disabled

■Serial Ports submenu （） The initial values have been unchanged.

Item Initial value Setting

Examine and set serial port parameters.

COM1 Enable Enabled ( )Disabled Address 3F8 ( )2F8 ( )3E8 ( )2E8 IRQ 4 ( )3

13 B Configuration Sheets of BIOS Setup Utility Parameters

■PCI submenu

（） The initial values have been unchanged. Item Initial value Setting

Examine and set PCI system bus parameters.

Enable Slot 1 ROM Disabled ( )Enabled Enable Slot 2 ROM Disabled ( )Enabled Enable Slot 3 ROM Disabled ( )Enabled Enable Slot 4 ROM Disabled ( )Enabled Enable Slot 5 ROM Disabled ( )Enabled Enable Slot 6 ROM Disabled ( )Enabled Enable Slot 7 ROM Disabled ( )Enabled Enable FC Card ROM Disabled ( )Enabled Boot to ROMB Hard Drive Auto ( )First ( )Last PCI memory mapped IO space *1 1G ( )2G ( )3G

*1： The memory capacity that BIOS secures for the PCI slot.

Ｂ.５ Parameters in the Server Menu

（） The initial values have been unchanged.

Item Initial value Setting

Examine and set server management parameters.

SM Error Halt Disabled ( )Enabled

> ASR&R Links to ASR&R submenu

> Console Redirection Links to Console Redirection submenu > BMC Information Links to BMC Information submenu > LAN Management Links to LAN Management submenu > SEL Logging Links to SEL Logging submenu

WOL Resume from S5 Enabled ( )Disabled Reset on Fatal Error Disabled ( )Enabled

14 PRIMERGY RX600 S3 Configuration Sheets

■ASR&R submenu

（） The initial values have been unchanged.

Item Initial value Setting

Examine and set Automatic Server Recovery and Reboot (ASR&R) parameters.

O/S Boot Timeout Disabled ( )Enabled O/S Boot WD Time (min) 100 ( )[0 ～100] O/S Boot WD Behavior Continue ( )Reset ( )Power Cycle ASR&R Boot Delay (min) 2 ( )[0 ～30] Power Cycle Delay 5 ( )[0 ～15] Boot Retry Counter 3 ( )[0 ～7] Diagnostic System Disabled ( )PXE (Lan) Image Next Boot Uses Boot Option ( )Diagnostic System Diagnostic Lan Device Use Boot Order ( )LAN1 Temperature Monitoring Disabled ( )Enabled

■Console Redirection submenu

（） The initial values have been unchanged.

Item Initial value Setting

Examine and set server management parameters.

> COM1 Console Redirection Links to COM1 Console Redirection submenu

Console Redirection Mode Standard ( )Enhanced

■COM1 Console Redirection submenu

（） The initial values have been unchanged.

Item Initial value Setting

Examine and set console redirection parameters.

Console Redirection Disabled ( )Enabled Flow Control None ( )RTS/CTS ( )XON/XOFF ( )RTS/CTS + CD Baud Rate 19.2k ( )9.6k ( )38.4k ( )57.6k ( )115.2k Terminal Type VT100+ ( )PC-ANSI ( )VT100 ( )VT-UTFB

15 B Configuration Sheets of BIOS Setup Utility Parameters

■BMC Information submenu （） The initial values have been unchanged.

Item Initial value Setting

Examine Field Replaceable Units (FRU) parameters.

Board Part Number Displays the revision of BMC board. Board Serial Number Displays the serial number of BMC board. （unsupported） System Part Number Displays the parts number of the server. System Serial Number Displays the serial number of the server. （unsupported） Chassis Part Number Displays the parts number of the device. （unsupported） Chassis Serial Number Displays the serial number of the device. （unsupported） BMC Firmware Revision Displays the firmware revision of BMC. SDR Revision Displays the revision of SDR.

■LAN Management submenu （） The initial values have been unchanged.

Item Initial value Setting

Examine and set LAN management parameters.

LAN Controller 1: Static IP Enable Disabled ( )Enabled Host IP Address 0.0.0.0 Router IP Address 0.0.0.0 NIC 1 MAC Address Displays the MAC address of the LAN port 1 .

■SEL Logging submenu （） The initial values have been unchanged.

Item Initial value Setting

Examine and set System Event Log (SEL) options.

Clear Log Disabled ( )Enabled

Event Log Full Mode Overwrite ( )Maintain

16 PRIMERGY RX600 S3 Configuration Sheets

Ｂ.６ Parameters in the Security Menu

（） The initial values have been unchanged.

Item Initial value Setting

Examine and set security options. Administrator Password is Displays whether or not the Administrator password is set. User Password is Displays whether or not the user password is set.

Set Administrator Password *1 The Administrator password is set. Set User Password *1 The system password is set.

Password on Boot Disabled ( )Enabled

*1： Password setting window is displayed by pressing the [Enter] key.

17 C Table of System Resource Management

Ｃ Table of System Resource Management

The I/O port address that can be selected with various expansion cards are described in the following table.

■I/O port addresses

I/O port address （h） Product name 100 140 180 1C0 200 240 2802C0 300 340 380 3C0 400 Setup method ｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜

Serial port 1 ｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜ BIOS setup

Serial port 2 ｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜ BIOS setup

Parallel port 1 ｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜｜ BIOS setup

＊ indicate the I/O port address space that can be selected in the expansion card. indicates that some or all of the 16 bytes that follow the marker address may be used （ space selected for default) indicates that some or all of the 32 bytes that follow the marker address may be used （ space selected for default)

18 PRIMERGY RX600 S3 Configuration Sheets

Ｄ Design Sheet of the RAID Configuration

Use this form to record the definitions of the physical packs and the logical drives in the RAID configuration (array configuration).

Ｄ.１ For RX600 S3 Onboard SCSI Array Controller （MegaRAID SCSI 320-2E）

■ Definition of the Physical Pack

Installation HDD destination HDD Physical pack HDD model HDD Location of SCSI channel destination （Array） name capacity HDD （CH）*1 SCSI ID*2 / Spare disk *3 (3)Physical pack [0] （e.g.） Bay 1 CH : 0 ID : 0 PG-HDH75W 73.4GB ( )Spare disk (3)Physical pack [0] （e.g.） Bay 4 CH : 1 ID : 0 PG-HDH75W 73.4GB ( )Spare disk ( )Physical pack [ ] CH : ID : ( )Spare disk ( )Physical pack [ ] CH : ID : ( )Spare disk ( )Physical pack [ ] CH : ID : ( )Spare disk ( )Physical pack [ ] CH : ID : ( )Spare disk ( )Physical pack [ ] CH : ID : ( )Spare disk

When two or more array controllers are installed, copy this sheet for each array controller.

*1: Fill in the SCSI channel number of hard disk destination. *2: Fill in the SCSI ID number of hard disk destination. *3: When the hard disk is included in the physical pack, put a checkmark to "Physical pack" and fill in the physical pack number in [ ]. The physical pack number is allocated in order defining it like 0, 1, 2, ….

19 D Design Sheet of the RAID Configuration

■Definition of the Logical Drive

Logical drive number Disk group number Logical drive RAID level Write policy （LD No.）*1 （DG No.）*2 capacity ( )RAID 0 (3)RAID 1 (3)Write Through (e.g.) LD : 0 DG : 0 34464 MB ( )RAID 5 ( )Write Back ( )RAID 10 ( )RAID 0 (3)RAID 1 (3)Write Through (e.g.) LD : 1 DG : 0 34464 MB ( )RAID 5 ( )Write Back ( )RAID 10 ( )RAID 0 ( )RAID 1 ( )Write Through LD : DG : ( )RAID 5 ( )Write Back ( )RAID 10 ( )RAID 0 ( )RAID 1 ( )Write Through LD : DG : ( )RAID 5 ( )Write Back ( )RAID 10 ( )RAID 0 ( )RAID 1 ( )Write Through LD : DG : ( )RAID 5 ( )Write Back ( )RAID 10 ( )RAID 0 ( )RAID 1 ( )Write Through LD : DG : ( )RAID 5 ( )Write Back ( )RAID 10 ( )RAID 0 ( )RAID 1 ( )Write Through LD : DG : ( )RAID 5 ( )Write Back ( )RAID 10 ( )RAID 0 ( )RAID 1 ( )Write Through LD : DG : ( )RAID 5 ( )Write Back ( )RAID 10 ( )RAID 0 ( )RAID 1 ( )Write Through LD : DG : ( )RAID 5 ( )Write Back ( )RAID 10 ( )RAID 0 ( )RAID 1 ( )Write Through LD : DG : ( )RAID 5 ( )Write Back ( )RAID 10

When two or more array controllers are installed, copy this sheet for each array controller.

*1: Fill in the logical drive number. The logical drive number is allocated in order defining it like 0, 1, 2, …. *2: Fill in the physical pack number defined in "■Definitions of the Physical Pack". When two or more physical packs are used for RAID 10, fill in the range of physical pack number like "0 - 2".

20 PRIMERGY RX600 S3 Configuration Sheets

Ｄ.２ For PG-142E3 （MegaRAID SCSI 320-2）

■Definition of the Physical Pack Installed PCI slot：（） Installation HDD destination HDD Physical pack HDD model HDD Location of SCSI channel destination （Array） name capacity HDD （CH）*1 SCSI ID*2 / Spare disk *3 (3)Physical pack [0] （e.g.） Slot 1 CH : 0 ID : 0 PG-HDH75V 73.4GB ( )Spare disk (3)Physical pack [0] （e.g.） Slot 2 CH : 0 ID : 1 PG-HDH75V 73.4GB ( )Spare disk ( )Physical pack [ ] CH : ID : ( )Spare disk ( )Physical pack [ ] CH : ID : ( )Spare disk ( )Physical pack [ ] CH : ID : ( )Spare disk ( )Physical pack [ ] CH : ID : ( )Spare disk ( )Physical pack [ ] CH : ID : ( )Spare disk ( )Physical pack [ ] CH : ID : ( )Spare disk ( )Physical pack [ ] CH : ID : ( )Spare disk ( )Physical pack [ ] CH : ID : ( )Spare disk ( )Physical pack [ ] CH : ID : ( )Spare disk ( )Physical pack [ ] CH : ID : ( )Spare disk ( )Physical pack [ ] CH : ID : ( )Spare disk ( )Physical pack [ ] CH : ID : ( )Spare disk ( )Physical pack [ ] CH : ID : ( )Spare disk ( )Physical pack [ ] CH : ID : ( )Spare disk

When two or more array controllers are installed, copy this sheet for each array controller.

21 D Design Sheet of the RAID Configuration

■Definition of the Logical Drive

Installed PCI slot : ( ）

Logical drive number Physical pack Logical drive RAID level Write policy （LD No.）*1 number （DG No.）*2 capacity ( )RAID 0 (3)RAID 1 (3)Write Through (e.g.) LD : 0 Array : 0 34464 MB ( )RAID 5 ( )Write Back ( )RAID 10 ( )RAID 0 (3)RAID 1 (3)Write Through (e.g.) LD : 1 Array : 0 34464 MB ( )RAID 5 ( )Write Back ( )RAID 10 ( )RAID 0 ( )RAID 1 ( )Write Through LD : Array : ( )RAID 5 ( )Write Back ( )RAID 10 ( )RAID 0 ( )RAID 1 ( )Write Through LD : Array : ( )RAID 5 ( )Write Back ( )RAID 10 ( )RAID 0 ( )RAID 1 ( )Write Through LD : Array : ( )RAID 5 ( )Write Back ( )RAID 10 ( )RAID 0 ( )RAID 1 ( )Write Through LD : Array : ( )RAID 5 ( )Write Back ( )RAID 10 ( )RAID 0 ( )RAID 1 ( )Write Through LD : Array : ( )RAID 5 ( )Write Back ( )RAID 10 ( )RAID 0 ( )RAID 1 ( )Write Through LD : Array : ( )RAID 5 ( )Write Back ( )RAID 10 ( )RAID 0 ( )RAID 1 ( )Write Through LD : Array : ( )RAID 5 ( )Write Back ( )RAID 10 ( )RAID 0 ( )RAID 1 ( )Write Through LD : Array : ( )RAID 5 ( )Write Back ( )RAID 10

When two or more array controllers are installed, copy this sheet for each array controller.

22 PRIMERGY RX600 S3 Configuration Sheets

Ｅ Design Sheet

When setting up the server using ServerStart, select the setting values and put a check mark in parentheses below in advance to ensure setup is performed smoothly.

Ｅ.１ RAID/Disk Wizard

Parameters Setting ( ) Logical Drive View ( ) Mass Storage Controller View (The RAID configuration can be specified) ( ) RAID ( ) SCSI Controller ( ) Fibrechannel ( ) IDE When you select "RAID" with controller's type Configure RAID ( ) Automatically ( ) Manually Existing RAID Array ( ) Delete Existing RAID Array Controller Vendor Controller Number Configure RAID： RAID Level Manually Number of Disks HotSpare ( ) Yes ( ) No Disk ↓Make copies when installing multiple disks. Partition ↓Make copies when more sheets are needed. Volume label File system ( ) NTFS ( ) FAT Partition size ( ) Auto setting ( ) MB Quick format ( ) Execute ( ) Do not execute Partition Usage ( ) Boot ( ) OS ( ) Data

23 E Design Sheet

Ｅ.２ OS Wizard (Windows 2003 Install Wizard)

Parameters Setting Install Windows 2003 Password for Administrator account Computer Identification When selecting Windows Server 2003/R2 to install ( ) Windows Server 2003, Standard Edition ( ) Windows Server 2003, Standard Edition including SP1 ( ) Windows Server 2003, Enterprise Edition ( ) Windows Server 2003, Enterprise Edition including SP1 ( ) Windows Server 2003 R2, Standard Edition Operating System Type ( ) Windows Server 2003 R2, Enterprise Edition

Windows Server 2003 x64/R2 to install ( ) Windows Server 2003, Standard x64 Edition ( ) Windows Server 2003, Enterprise x64 Edition ( ) Windows Server 2003 R2, Standard x64 Edition ( ) Windows Server 2003 R2, Enterprise x64 Edition ( ) per Seat License Mode ( ) per Server User permitted (Only when concurrent users are selected) will participate in ( ) a work group ( ) a domain Workgroup or Domain Name (Default - MYUSERGROUP) User account to create computer account (only when Domain is selected) User account Password ( ) Operating system source media in Available in local CD-ROM drive Installation method ( ) Operating system source media in Available on a remote share when installing OS from remote share Remote Source Path Remote Username Remote Password To install Windows Server ( ) Install Windows Server 2003 R2 Components 2003 R2 Components ( ) R2 Componentｓ source media is available in local CD-ROM drive Installation method ( ) R2 Componentｓ source media is available on a remote share When you install it from a remote share Remote Source Remote Username Reote Password (continued)

24 PRIMERGY RX600 S3 Configuration Sheets

Parameters Setting Installation Directory and Time zone (Default -(GMT+01:00) Amsterdam, Berlin, Time Zone Bern, Rome, Stockholm, Vienna) Installation Drive ( ) Use default ( ) Drive Letter ( ) C: ( ) D: ( ) E: ( ) F: ( ) G: ( ) H: ( ) I: ( ) J: When selecting drive name ( ) K: ( ) L: ( ) M: ( ) N: ( ) O: ( ) P: ( ) Q: ( ) R: ( ) S: ( ) T: ( ) U: ( ) V: ( ) W: ( ) X: ( ) Y: ( ) Z: Installation Directory ( ) Use default ( ) Specify in advance Installation destination (Default - \winnt) User Name User Name Organization Computer Name Product-ID ( ) ― ― ― ― Display settings ( ) 640 * 480 ( ) 800 * 600 ( ) 1024 * 768 Resolution ( ) 1156 * 864 ( ) 1280 * 1024 ( ) 1600 * 1200 Vrefresh ( ) 60 ( ) 70 ( ) 72 ( ) 75 ( ) 80 ( ) 85 ( ) 100 ( ) 16 colors ( ) 256 colors ( ) High Color（16bits） BitsPerPel ( ) True Color（24bits） ( ) True Color（32bits） Network protocol ( ) Install Unattended Installation method ( ) Install Manually Network protocol property (for auto-installation) Connection name ( ) TCP/IP ( ) NWIPX ( ) NetBEUI ( ) Apple Talk Available Protocols ( ) DLC ( ) NetMon ( ) PPTP Use of DHCP ( ) Use DHCP (When TCP/IP selected) IP-Address Subnet Mask

Do not use DHCP use Do not Default Gateway IP address (additional) (only when added) Subnet mask (additional) (only when added) Adapter 1 Default gateway (only when added) (additional) DNS domain name (only when specified) DNS server address (only when specified) Use WINS ( ) Use WINS server address DHCP (only when selected to use) ( ) Use NetBIOS setting from the DHCP Server NetBIOS Option ( ) Use NetBIOS over TCP/IP ( ) Do not use NetBIOS over TCP/IP Only when NWIPX is selected Internal network number 0x Network number 0x Frame type Copy this sheet to install multiple adapters. (continued)

25 E Design Sheet

Parameters Setting (Continuation of Network protocol) Connection name Protocol binding to this ( ) TCP/IP ( ) NWIPX ( ) NetBEUI ( ) Apple Talk adapter ( ) DLC ( ) NetMon ( ) PPTP Use of DHCP ( ) Use DHCP (When TCP/IP selected) IP Address Subnet Mask Default Gateway Do not use DHCP not Do IP address (additional) (only when added)

Adapter 2 Subnet mask (additional) (only when added) Default gateway (only when added) (additional) DNS domain name (only when specified) DNS server address (only when specified) Use WINS ( ) Use WINS server address DHCP (only when selected to use) ( ) Use NetBIOS setting from the DHCP Server NetBIOS Option ( ) Use NetBIOS over TCP/IP ( ) Do not use NetBIOS over TCP/IP Only when NWIPX is selected Internal network number 0x Network number 0x Frame type Copy this sheet to install multiple adapters. (continued)

26 PRIMERGY RX600 S3 Configuration Sheets

Parameters Setting Software Components ( ) Install default Components Select installation method ( ) Install customized Components R2 ( ) R2 Components Only when selecting R2 components to install

( ) Application Mode（ADAM） ( ) Claims-Aware Applications Active Directory ( ) Traditional Applications ( ) Federation Service ( ) Federation Service Proxy

( ) DFS Management Distributed File System ( ) DFS Replication Service File Server ( ) Management Console ( ) User Name Mapping ( ) Microsoft Services for NFS Administration ( ) Client for NFS Microsoft Services for NFS ( ) Server for NFS ( ) RPC Portmapper ( ) RPC External Data Representation ( ) Server For NFS Authentication ( ) Administration Components Unix Identity Management ( ) Password Synchronisation ( ) Server For NIS Windows SharePoint Services Enable Windows Sharepoint Services ( ) Common Log File System ( ) Microsoft .NET Framework2.0(English) ( ) Microsoft .NET Framework2.0(International) ( ) Microsoft .NET Framework2.0 Languagepack Additional Components ( ) Print Management Console ( ) Storage Manager SAN ( ) Storage Ressource Manager ( ) Windows Subsystem for UNIX based Applications

( ) uninstall hidden CFSCommonUIFX ( ) uninstall hidden DFSExt Uninstall Componennts ( ) uninstall hidden DFSRHelper ( ) uninstall set of files from FileServerManagement Console (continued)

27 E Design Sheet

Parameters Setting (Continuation of Software Components) Only when selecting component to install Application and utilities ( ) clipboard viewer ( ) Desktop Wallpaper ( ) Document Template ( ) Paint Accessories ( ) All available mousepointers ( ) Word pad ( ) Calculator ( ) Character Map Accessibility Wizard ( ) Install ( ) Chat Communications ( ) Hyper Terminal Application server ASP.NET web ( ) Install development platform Application server ( ) Install console ( ) FrontPage 2002 Server Extensions ( ) FTP (File Transfer Protocol) service ( ) NNTP Service - NNTP Service ( ) SMTP Service - SMTP Service ( ) World Wide Web Server - Internet Information Services ASP support Internet information ( ) World Wide Web Server services - Internet Information Services web DAV publishinｇ (IIS) ( ) World Wide Web Server - World Wide Web (WWW) Service ( ) World Wide Web Server - Internet Information Services internet data connector ( ) World Wide Web Server - Internet Information Services web user interface network COM + access ( ) Install DTC network access ( ) Install Indexing Server Files ( ) Install Terminal Services ( ) Install Terminal Services licensing ( ) Install Remote install Services ( ) Install ( ) Install ( ) Server components of the Certificate Services Certificate Service ( ) Web client component of the Certificate Services

( ) Install ( ) POP3 main service POP3 root component ( ) POP3 web user interface (continued)

28 PRIMERGY RX600 S3 Configuration Sheets

Parameters Setting FTP service property (Only when FTP service is selected) FTP site directory (Default - \Inetpub\Ftproot) WWW service property (Only when WWW service is selected) WWW server directory (Default - \Inetsrv\WWWroot) Terminal server property (Only when terminal server is selected) Terminal service ( ) Permit remote desktop during unattended setup Authorize the following access ( ) Access permit compatible with Windows 2000 Users permits to terminal service ( ) Access permit compatible with Terminal Server 4.0 Users users ( ) Number of simultaneous users License mode ( ) Number of connected sessions Current mode for terminal ( ) Application server mode service ( ) Remote management mode Services ( ) Services for Macintosh (SFM) Other network File and Print ( ) Print Service for Macintosh Services ( ) Print Service for UNIX ( ) WINS Server ( ) Internet Authentication Service (IAS) Networking Services ( ) MS DNS Server ( ) Simple TCP/IP Service ( ) MS DHCP Serve

Management and Monitoring ( ) Network Monitor tools Tools ( ) SNMP Service (Required to install SNMP-ServerView)

SNMP details (Only when SNMP is selected) Trap Community name Trap destination Security Send authentication trap ( ) Send Receivable community name Receive SNMP packet ( ) Receive from all hosts Host name (only when specified) Agent Contact Address ( ) Physical ( ) Datalink and sub network Service ( ) End-to-End ( ) Application ( ) Internet (continued)

29 E Design Sheet

Parameters Setting Active Directory details setting (only when DNS is selected) Install Active Directory ( ) Install ( ) Create a domain in a new forest ( ) Additional domain controller of the existing domain Active Directory type ( ) Create a new child domain under the existing domain tree ( ) Create a new domain tree in the existing fores Database folder Log folder SYSVOL folder location Compatibility with ( ) Permit Windows 2000 or earlier Create a domain in a new forest (only when selected) Complete DNS name of the new domain Domain NetBIOS name Additional domain controller of the existing domain (only when selected) User name Password Domain Complete DNS name of the existing domain Create a new child domain under the existing domain tree (only when selected) User name Password Domain Complete DNS name of the parent domain New child domain name Domain NetBIOS name Create a new domain tree in the existing forest (only when selected) User name Password Domain name Complete DNS name of the new domain Domain NetBIOS name

30 PRIMERGY RX600 S3 Configuration Sheets

Ｅ.３ OS Wizard (Windows 2000 Install Wizard)

Parameters Setting Install Windows 2000 Password for Administrator Computer identification ( ) Windows 2000 Server including SP4 OS ( ) Windows 2000 Advanced Server including SP4 ( ) per Seat License mode ( ) per Server User Permitted (Only when concurrent users are selected) Participation ( ) a work group ( ) a domain Work group or domain name (Default - MYUSERGROUP) User account to create computer account (only when Domain is selected) User account Password ( ) Operating system source media in Available in local CD-ROM drive Installation method ( ) Operating system source media in Available on a remote share when installing OS from remote share Remote source Remote Username Reote Password Time zone and installation drive (Default -(GMT+01:00) Amsterdam, Berlin, Select time zone Bern, Rome, Stockholm, Vienna) Installation drive ( ) Use default ( ) Drive name ( ) C: ( ) D: ( ) E: ( ) F: ( ) G: ( ) H: ( ) I: ( ) J: When selecting drive name ( ) K: ( ) L: ( ) M: ( ) N: ( ) O: ( ) P: ( ) Q: ( ) R: ( ) S: ( ) T: ( ) U: ( ) V: ( ) W: ( ) X: ( ) Y: ( ) Z: ( ) Use default ( ) Specify during installation Installation directory ( ) Specify in advance Installation destination (Default - \winnt) User information Name Company name Computer name Product-ID ( ) ― ― ― ― Display setting ( ) 640 * 480 ( ) 800 * 600 ( ) 1024 * 768 Resolution ( ) 1156 * 864 ( ) 1280 * 1024 ( ) 1600 * 1200 Vrefresh ( ) 60 ( ) 70 ( ) 72 ( ) 75 ( ) 80 ( ) 85 ( ) 100 ( ) 16 colors ( ) 256 colors ( ) High Color（16bits） BitsPerPel ( ) True Color（24bits） ( ) True Color（32bits） (continued)

31 E Design Sheet

Parameters Setting Network protocol ( ) Auto-installation Installation method ( ) Install driver only Network protocol property (when auto-installation is selected) Connection name Protocol binding to this ( ) TCP/IP ( ) NWIPX ( ) NetBEUI ( ) Apple Talk adapter ( ) DLC ( ) NetMon ( ) PPTP Use of DHCP ( ) Use (When TCP/IP selected) IP-Address Subnet Mask Default Gateway

Do not use DHCP Do not use IP address (only when added) (additional) Subnet mask (only when added) (additional) Adapter 1 Default gateway (only when added) (additional) DNS domain name (only when specified) DNS server address (only when specified) Use WINS ( ) Use WINS server address (only when selected to use WINS) ( ) Use NetBIOS setting from the DHCP Server NetBIOS Option ( ) Enable NetBIOS over TCP/IP ( ) Disable NetBIOS over TCP/IP Only when NWIPX is selected Internal network 0x number Network number 0x ( ) Ethernet Ⅱ ( ) Ethernet 802.2 ( ) Ethernet 802.3 Frame type ( ) Ethernet SNAP ( ) Auto-detection Copy this sheet to install multiple adapters. (continued)

32 PRIMERGY RX600 S3 Configuration Sheets

Parameters Setting (Continuation of Network protocol) Connection name Protocol binding to this ( ) TCP/IP ( ) NWIPX ( ) NetBEUI ( ) Apple Talk adapter ( ) DLC ( ) NetMon ( ) PPTP Use of DHCP ( ) Use (When TCP/IP selected) IP Address Subnet Mask Default Gateway

Do not use DHCP Do not use IP address (only when added) (additional) Subnet mask (only when added) (additional) Adapter 2 Default gateway (only when added) (additional) DNS domain name (only when specified) DNS server address (only when specified) Use WINS ( ) Use WINS server address (only when selected to use WINS) ( ) Use NetBIOS setting from the DHCP Server NetBIOS Option ( ) Enable NetBIOS over TCP/IP ( ) Disable NetBIOS over TCP/IP Only when NWIPX is selected Internal network 0x number Network number 0x ( ) Ethernet Ⅱ ( ) Ethernet 802.2 ( ) Ethernet 802.3 Frame type ( ) Ethernet SNAP ( ) Auto-detection Copy this sheet to install multiple adapters. (continued)

33 E Design Sheet

Parameters Setting Software Components Select installation method ( ) Select component to install Only when selecting component to install ( ) (IIS) common component ( ) (IIS) online help ( ) FTP (File Transfer Protocol) server ( ) Internet service manager (HTML) ( ) Internet information service snap-in ( ) NNTP Service Service ( ) SMTP Service ( ) WWW (World Wide Web) server ( ) Remote install service ( ) Remote storage ( ) Terminal service ( ) Terminal service license

FTP site directory (Default - \Inetpub\Ftproot) WWW Server directory (Default - \Inetsrv\WWWroot) Communication Setting ( ) CD player ( ) Media player Multimedia ( ) Utopia sound setting ( ) Sound recorder ( ) Volume control ( ) Sample sound ( ) Accessibility setting wizard ( ) Character code table ( ) Calculator ( ) Paint Accessory ( ) Word pad ( ) Document templates ( ) Script debugger ( ) Object packager ( ) Desktop wallpaper Game ( ) Free cell ( ) Mine sweeper ( ) Pinball ( ) Solitaire Service ( ) Simple Network Management Protocol (SNMP) ( ) Domain Name System (DNS) ( ) Dynamic Host Configuration Protocol (DHCP) ( ) Windows Internet Name Service (WINS) ( ) Simple TCP/IP service ( ) Network monitor tool Service ( ) Internet authentication service ( ) Site Server ILS service ( ) Print service for UNIX ( ) Print service for Macintosh ( ) Connection manager component ( ) File service for Macintosh (continued)

34 PRIMERGY RX600 S3 Configuration Sheets

Parameters Setting SNMP details (only when SNMP is selected) Trap Community name Trap destination Security Send authentication trap ( ) Send Receivable community name Receive SNMP packet ( ) Receive from all hosts Host name (only when specified) Agent Contact Address ( ) Physical ( ) Datalink and sub network Service ( ) End-to-End ( ) Application ( ) Internet

35 E Design Sheet

Parameters Setting Active Directory details setting (only when DNS is selected) Install Active Directory ( ) Install ( ) Create a new forest of a domain tree ( ) Add additional domain controller of the existing domain Active Directory type ( ) Add a new child domain under the existing domain tree ( ) Place a new domain tree in the existing forest Database location Log location SYSVOL folder location Access permit compatibility with Windows ( ) Permit 2000 or earlier server Create a new forest of a domain tree (only when selected) Complete DNS name of the new tree Domain NetBIOS name Add additional domain controller of the existing domain (only when selected) User name Password Domain Complete DNS name of the domain Add a new child domain under the existing domain tree (only when selected) User name Password Domain Parent domain name Child domain name Domain NetBIOS name Place a new domain tree in the existing forest (only when selected) User name Password Domain name Complete DNS name of the new tree Domain NetBIOS name

36 PRIMERGY RX600 S3 Configuration Sheets

Ｅ.４ Application Wizard

Parameters Setting

( ) Windows Server 2003 service pack1 ( ) ServerView Installable applications ( ) DSNAP ( ) RAID Management Tool ( ) Broadcom Advanced Control Suite(BACS)

Userspecific Command (only when selecting additional software) ( ) Install selected application from Local CD Userspecific Command ( ) Install selected application from Remote Server When installing from remote server ( ) Install ( ) Do not install Remote Source Path Remote Username Remote Password

37 F Accident Sheet

Ｆ Accident Sheet

Name (Product ID) □ PRIMERGY RX600 S3 (PG )

Environment

LAN/WAN config.

DATE/TIME

Phase of accident What did you do?, what message? etc.

Attached paper Yes / No

38 PRIMERGY RX600 S3

Configuration Sheets CA92276-5642-01

Issued on November, 2006 Issued by FUJITSU LIMITED

・ The contents of this manual may be revised without prior notice. ・ Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information in this manual. ・ No part of this manual may be reproduced in any form without the prior written permission of Fujitsu.