DOCSLIB.ORG

How to Build a Simple and Strong Miter Saw Station

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
How to Build a Simple and Strong Miter Saw Station instructables How to Build a Simple and Strong Miter Saw Station by funwithwoodworking This miter saw station is made out of 13 - 8 foot 2x4's list, and step by step assembly directions can be and single sheet of 3/4" plywood cut down the middle found at: long ways. The main tools needed are a tape https://funwithwoodworking.com/product/mitre-saw- measure, a speed square, a miter saw, a drill, and a station/ circular saw. Clamps and a framing square are helpful but not 100% necessary. A full video of the build can be seen here: https://youtu.be/Nde1jGHNw5E Full plans with dimensions, material list, tool list, cut Step 1: Cut All the 2x4's to Length Cut all the 2x4's to their finished lengths according to the cut list in the plan. How to Build a Simple and Strong Miter Saw Station: Page 1 Step 2: Build the Right and Left Frames Build the right frame by making 4 legs with the small and the longer leg riser to the right. feet at the bottom and then screwing the front stretchers across the top of the feet. You then install The left side is built the same way except that you the side stretchers by screwing them into the inner attach the shorter leg riser to the right side and the side of the 4 legs. Once all the stretchers are screwed longer one to the left side. in you will attach the shorter leg riser to the left side How to Build a Simple and Strong Miter Saw Station: Page 2 Step 3: Attach the 2 Frames Together Place the left and right frames 24" apart and set the stretchers on top of the 2 short leg risers in the front and the back. Attach with 2 or 3 screws into each leg. Hold another stretcher in place at the level of the bottom shelf in the rear and attach it using 2 screws into the side of each leg. Mark the center of each top and install a cross brace by screwing through the stretcher into the cross brace. How to Build a Simple and Strong Miter Saw Station: Page 3 Step 4: Cut and Install the Plywood Shelves and Work Surface Measure the 2 bottom shelves and top center shelf and cut them from 1 of the 24" x 96" pieces of 3/4" plywood. Attach to the 2x4 stretcher with a screw into each corner. Measure the top work surface for length and cut the 2 pieces from the other half of the plywood. Attach to the stretchers with 4 screws along each front and 4 screws along each back. Step 5: Mount Your Miter Saw This station was designed with a 3 1/2" recessed shelf for the miter saw. The pictured saw has a 2 3/4" table height so we added a single layer of 3/4" plywood to bring it level to the work surface. Place your miter saw in the center of the middle shelf with the handle sticking out the front for easy movement and then attach using long screws or lag bolts depending on the size of your mounting holes. How to Build a Simple and Strong Miter Saw Station: Page 4 Step 6: Watch a Video of the Entire Build https://youtu.be/Nde1jGHNw5E Thanks for the tip. Charlessenf-gm, I do something similar on my workbench. The left and right outfeed sides next to the miter saw have blocks and shims to support long boards. But a dual left/right table would be so much nicer. Even if thin shims were needed to support the work. I made a similar arrangement which was all on the same frame and had 4 sets of swivel wheels on the bottom to allow it to be moved from the wall. The platform for my saw was made removable so I could make several stations/platforms for different power tools (table saw, planner, router, drill press and band saw). This gave me good work stations for my small work area. Thanks, that sounds like a good idea. Photos would be very nice ArtEdwards67. :) On my To Do list for my new shop--ha ha--my little corner of the garage-- is a miter saw table. I doubt I have the room for something this big, but yours is a perfect starting place for me to start planning. KJ This plan can definitely be scaled down to fit your needs. Here's a tip: put a floor in the tabletop and put hinges on the top piece with a flush handle in the front. Use this storage for hand tools, sockets, etc. I like that idea, but we plan on adding some kind of storage shelves behind the fence. I have not had the room to build one of these but the idea is great of course and well documented on instructables . What intrigued me however is why make it so deep . You only use the front foot of the benches to hold the timber to be cut and the back of the bench is mostly wasted . I realise the saw slides some have have to have that room to move behind. Perhaps other power tools can be mounted there and used from the other side? I also suggest you hang the power board on the back leg We are going to come back later and install a fence and some kind of storage in the back area. Very nice! I built an almost identical miter saw station many years ago. It held up great and was a fantastic and integral part of my evolving workshop. Very nicely done :) Thank you! How to Build a Simple and Strong Miter Saw Station: Page 5.
Load more

Recommended publications
  • IO-INCH DIRECT DRIVE BAND SA W CAUTION: Read GENERAL and ,, Assembly ADDITIONAL SAFETY INSTRUCTIONS • Operating Carefully , Repair Parts
    SAVE THIS MANUAL FOR FUTURE REFERENCE _ARS owners manual MODEL NO. 113.244512 Serial Number Model and serial number may be found at the right-hand side of the frame. You should record both model and serial number in a safe place for future use. IO-INCH DIRECT DRIVE BAND SA W CAUTION: Read GENERAL and ,, assembly ADDITIONAL SAFETY INSTRUCTIONS • operating carefully , repair parts Sold by SEARS, ROEBUCK AND CO., Chicago, IL. 60684 U.S.A. Part No. 69188 FULL ONE YEAR WARRANTY ON CRAFTSMAN BAND SAW If within one year from the date of purchase, this Craftsman Band Saw fails due to a defect in material or workmanship, Sears will repair it, free of charge. ,WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS SERVICE CENTER/DEPARTMENT THROUGHOUT THE UNITED STATES. THIS WARRANTY APPLIES ONLY WHILE THIS PRODUCT IS USED IN THE UNITED STATES. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state, SEARS, ROEBUCK AND CO.. 698/731A, Sears Tower, Chicago. IL 60684 general safety instructions for power tools 1. KNOW YOUR POWER TOOL Z87.1) at all times. Everyday eyeglasses only Read and understand the owner's manual and have impact resistant lenses, they are NOT labels affixed to the toot. Learn its application safety glasses. Also, use face or dust mask if and limitations as well as'the specific potential cutting operation is dusty, and ear protectors hazards peculiar to this toot, (plugs or muffs) during extended periods of 2. GROUND ALL TOOLS operation.
    [Show full text]
  • Paul Sellers' Workbench Measurements and Cutting
    PAUL SELLERS’ WORKBENCH MEASUREMENTS AND CUTTING LIST PAUL SELLERS’ WORKBENCH MEASUREMENTS AND CUTTING LIST NOTE When putting together the cutting list for my workbench, I worked in imperial, the system with which I am most comfortable. I was not happy, however, to then provide direct conversions to metric because to be accurate and ensure an exact fit this would involve providing measurements in fractions of millimetres. When I do work in metric I find it more comfortable to work with rounded numbers, therefore I have created two slightly different sets of measurements. This means that in places the imperial measurement given is not a direct conversion of the metric measurement given. Therefore, I suggest you choose one or other of the systems and follow it throughout. © 2017 – Paul Sellers v2 PAUL SELLERS’ WORKBENCH MEASUREMENTS AND CUTTING LIST WOOD QTY DESCRIPTION SIZE (IMPERIAL) SIZE (METRIC) (THICK X WIDE X LONG) (THICK X WIDE X LONG) 4 Leg 2 ¾” x 3 ¾” x 34 ⅜” 70 x 95 x 875mm 1 Benchtop 2 ⅜” x 12” x 66” 65 x 300 x 1680mm 2 Apron 1 ⅝” x 11 ½” x 66” 40 x 290 x 1680mm 1 Wellboard 1” x 12 ½” x 66” 25 x 320 x 1680mm 4 Rail 1 ½” x 6” x 26” 40 x 150 x 654mm 2 Bearer 1 ¼” x 3 ¾” x 25” 30 x 95 x 630mm 4 Wedge ⅝” x 1 ½” x 9” 16 x 40 x 228mm 4 Wedge retainer ⅝” x 1 ½” x 4” 16 x 40 x 100mm HARDWARE QTY DESCRIPTION SIZE (IMPERIAL) SIZE (METRIC) 1 Vise 9” 225mm Dome head bolts (including nuts and washers) for 4 ⅜” x 5” 10 x 130mm bolting legs to aprons 2 Lag screws (with washers) for underside of vise ½” x 2 ½” 12 x 65mm 2 Lag screws for face
    [Show full text]
  • MITER SAW SAFETY (Reviewed 9/27/2007)
    MITER SAW SAFETY (Reviewed 9/27/2007) 1. Tool Use and Care • Use clamps or other practical way to secure and support the work piece to a stable platform. Holding the work by hand or against you body is unstable. It allows for work to shift, causes binding of the tool and loss of control. • Do not force tool. Use correct tool for you application. The correct tool will do the job better and safer at the rate for which it is designed. Do not use the tool for purposes not intended – for example; do not use the miter saw for slicing meat. • Do not use tool if switch does not turn it “ON” or “OFF”. Any tool that cannot be controlled with the switch is dangerous. • Disconnect the plug from the power source before making any adjustments for changing accessories. Such prevention safety measures reduce the risk of starting the tool accidentally. • Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edges, are less likely to bind and easier to control. When mounting saw blades be certain that the arrow on the blade matches the direction of the arrow marked on the tool and that the teeth are also pointing in the same direction. • Inspect guards before using. Keep guards in place. Check moving parts for binding or any other condition that may affect the normal operation of safety features of the tool. If damaged, have tool serviced before using the tool. Many accidents are caused by poorly maintained tools. • Do not alter or misuse tool.
    [Show full text]
  • LS1219 / LS1219L Slide Compound Miter
    Satisfy Professional's Needs Max. cutting capacity (height x width) Slide Compound Miter Saw LS1219 / LS1219L 305mm (12") Cross Cut Miter Cut (left & right) Bevel Cut (left & right) Compound Cut Crown Baseboard molding, (Skirt board) 45 degree 90o type 90o 45o 45o 45o 90o 90o 45o Bevel Miter Bevel Miter Single sliding system Bevel 45o 61 x 268 left (2-3/8” x 10-1/2”) 92 x 268 61 x 382 enables smooth o o 45 (3-5/8”x10-1/2”) 45 (2-3/8” x 15” ) Upright cutting Upright cutting left/ 107 x 255 left 71 x 363 Miter 71 x 255 203 (8”) 171 (6-3/4”) right (4-1/4” x 10”) (2-13/16” x 14-1/4”) o 45 (2-13/16” x 10”) operation to produce 92 x 382 left/ (3-5/8” x 15”) right 107 x 363 Bevel superior cuts (4-1/4” x 14-1/4”) o 44 x 268 45 (1-3/4” x 10-1/2”) 92 x 185 44 x 382 right o o 60 (3-5/8” x 7-1/4”) 45 (1-3/4” x 15” ) Horizontal cutting Horizontal cutting left/ 107 x 178 right 54 x 363 Miter o right (4-1/4” 7”) (2-1/8” x 14-1/4”) 45 54 x 255 320 (12-5/8”) 416 (16-3/8”) left/ (2-1/8” x 10”) right (mm) Accessories Vertical vise assembly Dust bag assembly Stand Part No. 126617-2 Part No. 122852-0 Part No. WST06 Horizontal vise assembly Part No.
    [Show full text]
  • 10˝ Dual Speed Sliding Compound Miter Saw
    10˝ DUAL SPEED SLIDING COMPOUND MITER SAW LISTED E493385 For replacement parts visit Model # 70730 WENPRODUCTS.COM bit.ly/wenvideo IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for dependability, ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged, trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions. If you use your tool properly and for intended purpose, you will enjoy years of safe, reliable service. NEED HELP? CONTACT US! Have product questions? Need technical support? Please feel free to contact us at: 800-232-1195 (M-F 8AM-5PM CST) [email protected] WENPRODUCTS.COM TABLE OF CONTENTS Technical Data 2 Introduction 3 General Safety Rules 4 Specific Rules For the Miter Saw 6 Electrical Information 9 Unpacking and Transporting 10 Know your Miter Saw 10 Assembly and Adjustments 12 Operation 19 Maintenance 22 Exploded View & Parts List 23 Warranty 26 TECHNICAL DATA Model Number: 70730 Motor: 120 V, 60 Hz, 15A No-Load Speed: Speed 1: 2000 RPM Speed 2: 4500 RPM Blade Model Number: 70730-002 Blade Size: 10˝ TCT Multi-Purpose Blade Arbor Size: 5/8 in. Arbor Number of Teeth: 48 Teeth Miter Table Angles: 0° to 45° Left & Right Bevel Cut Angles: 0° to 45° Left Only Cutting Capacity: 0° Miter, 0° Bevel: 12 by 3-1/2 in. 45° Miter, 0° Bevel: 8-1/2 by 3-1/2 in. 0° Miter, 45° Bevel: 12 by 1-7/8 in. 45° Miter, 45° Bevel: 8-1/2 by 1-7/8 in.
    [Show full text]
  • Compound Sliding Miter Saw About
    Compound Sliding Miter Saw About Miter saws are saws designed to perform quick accurate crosscuts in materials such as wood and some plastics. The tool shop miter saw is a dual action compound sliding miter saw. This means that it is capable a large cuts up to 4 inches by 12 inches nominal size. The compound feature of the saw allows both miter and bevel cuts to be made at the same time. Miter adjustments are from 50 degrees to the left of square and 60 degrees to the right of square. Bevel adjustments are 45 degrees in either direction of the vertical position. Class Goal The goal of this class is to allow students to become certified safe operators of the tool shop miter saw. This handout along with hands on training will provide the information needed to operate the miter saw in a safe and efficient manner. You must successfully pass both the hands on training and quiz to become fully certified. SAFETY! Shop Safety: • Remember to always wear closed two shoes in the shop area at ALL times. • Always make sure to have long hair tied back and loose clothing secured. • Never leave a machine running unattended. They can have a mind of their own sometimes. • Never interrupt someone while they are using a piece of equipment. • Always report any incident to the shop supervisor immediately. • Check in with the shop supervisor before using any equipment in the tool shop. • Never attempt to repair or modify any equipment. • Always cleanup work area and return tools to their proper locations when finished.
    [Show full text]
  • Operator's Manual
    OPERATOR’S MANUAL 10 in. Compound Miter Saw TS1345L - Double Insulated 31.6 22.5 22.5 31.6 Your miter saw has been engineered and manufactured to our high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this product. Thank you for your purchase. SAVE THIS MANUAL FOR FUTURE REFERENCE TABLE OF CONTENTS Introduction ..................................................................................................................................................................... 2 Warranty .......................................................................................................................................................................... 2 General Safety Rules ....................................................................................................................................................3-4 Specific Safety Rules ....................................................................................................................................................4-5 Symbols ........................................................................................................................................................................... 6 Electrical .........................................................................................................................................................................
    [Show full text]
  • Brembana Kosmos
    brembana kosmos jet 5 axes saw jet machine STONE CMS is part of SCM Group, a technological world leader in processing a wide CMS SpA manufactures machinery and systems for the machining of composite range of materials: wood, plastic, glass, stone, metal and composites. The materials, carbon fibre, aluminium, light alloys, plastic, glass, stone and metals. It was Group companies, operating throughout the world, are reliable partners of established in 1969 by Mr Pietro Aceti with the aim of offering customized and state- brembana kosmos jet leading manufacturing industries in various market sectors, including the of-the-art solutions, based on the in-depth understanding of the customer’s production furniture, construction, automotive, aerospace, ship-building and plastic needs. Significant technological innovations, originating from substantial investments processing industries. SCM Group coordinates, supports and develops a in research and development and take-overs of premium companies, have enabled system of industrial excellence in 3 large highly specialized production constant growth in the various sectors of reference. centres employing more than 4,000 workers and operating in all 5 continents. SCM Group: the most advanced skills and know-how in the fields of industrial machinery and components. APPLICATIONS 4-5 BREMBANA KOSMOS JET TECHNOLOGICAL BENEFITS 6-7 ACCESSORIES 8-13 OPTIONAL 14-15 SOFTWARE 16-17 CMS Stone Technology realizes avant-garde solutions for the working of marble, natural stones and composite stones. Under OVERALL DIMENSIONS & TECHNICAL DATA the brand name Brembana Macchine, CMS Stone Technology was in the 80’s the first manufacturer of a stone machining 18-19 centre, thanks to an idea of its founder Mr Pietro Aceti.
    [Show full text]
  • 1. Hand Tools 3. Related Tools 4. Chisels 5. Hammer 6. Saw Terminology 7. Pliers Introduction
    1 1. Hand Tools 2. Types 2.1 Hand tools 2.2 Hammer Drill 2.3 Rotary hammer drill 2.4 Cordless drills 2.5 Drill press 2.6 Geared head drill 2.7 Radial arm drill 2.8 Mill drill 3. Related tools 4. Chisels 4.1. Types 4.1.1 Woodworking chisels 4.1.1.1 Lathe tools 4.2 Metalworking chisels 4.2.1 Cold chisel 4.2.2 Hardy chisel 4.3 Stone chisels 4.4 Masonry chisels 4.4.1 Joint chisel 5. Hammer 5.1 Basic design and variations 5.2 The physics of hammering 5.2.1 Hammer as a force amplifier 5.2.2 Effect of the head's mass 5.2.3 Effect of the handle 5.3 War hammers 5.4 Symbolic hammers 6. Saw terminology 6.1 Types of saws 6.1.1 Hand saws 6.1.2. Back saws 6.1.3 Mechanically powered saws 6.1.4. Circular blade saws 6.1.5. Reciprocating blade saws 6.1.6..Continuous band 6.2. Types of saw blades and the cuts they make 6.3. Materials used for saws 7. Pliers Introduction 7.1. Design 7.2.Common types 7.2.1 Gripping pliers (used to improve grip) 7.2 2.Cutting pliers (used to sever or pinch off) 2 7.2.3 Crimping pliers 7.2.4 Rotational pliers 8. Common wrenches / spanners 8.1 Other general wrenches / spanners 8.2. Spe cialized wrenches / spanners 8.3. Spanners in popular culture 9. Hacksaw, surface plate, surface gauge, , vee-block, files 10.
    [Show full text]
  • DP101 Manual
    OPERATOR’S MANUAL 10 in. (254 mm) DRILL PRESS MODEL DP101 THANK YOU FOR BUYING A RYOBI BENCH TOP DRILL PRESS. Your new Drill Press has been engineered and manufactured to Ryobi's high standards for dependability, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance. CAUTION: Carefully read through this entire operator's manual before using your new machine. Pay close attention to the Rules for Safe Operation, Warnings, and Cautions. If you use your machine properly and only for what it is intended, you will enjoy years of safe, reliable service. Please fill out and return the Warranty Registration Card so we can be of future service to you. Thank you again for buying Ryobi tools. SAVE THIS MANUAL FOR FUTURE REFERENCE 1 TABLE OF CONTENTS Rules for Safe Operation....................................................................................................................................................... 3 Specific Safety Rules for Drill Presses .................................................................................................................................. 5 Electrical.................................................................................................................................................................................6 Glossary of Terms ..................................................................................................................................................................7 Features .................................................................................................................................................................................8
    [Show full text]
  • Introduction and Analysis of the Ultrahigh Pressure Water Jet Cutting Multifunctional Application
    2017 WJTA-IMCA Conference and Expo October 25-27, 2017 ● New Orleans, Louisiana Paper INTRODUCTION AND ANALYSIS OF THE ULTRAHIGH PRESSURE WATER JET CUTTING MULTIFUCTIONAL APPLICATION Xue Shengxiong, Chen Zhengwen, Han Caihong, Ren Qile Hefei General Machinery Research Institute Hefei, Anhui, China Chen Bo Nanjing Dadi Water Limited by Share Ltd. Nanjing, Jiangsu, China Wu Ziquan All-Powerful Inc Shenyang, Liaoning, China Li Yuefeng Hua Zhen Mechanical Equipment Co. Ltd Guangzhou, Guangdong, China ABSTRACT The aerospace industry bring a new development for ultrahigh pressure water jet cutting technology, such as large scale curved composite components cutting process engineering application, large scale impeller rough cutting, special precise cutting, composite materials to milling, drill, polishing and so on. As National Advanced Technology Support Project of China for an opportunity, the author developed 500MPa ultrahigh pressure water cutting equipment for super large composite wing and a multifunction water jetting CNC center. This paper introduce the ultrahigh pressure water jet multifunctional technical features about these two equipments involved, and combine with the foreign development situation. The technical modules, parameter matching technology, process method and experiment result are analyzed to realizing the highly-difficult water jet cutting, milling and other applications. Organized and Sponsored by WJTA-IMCA 1. MARKET REQUIREMENT OF HIGH END ULTRAHIGH PRESSURE WATER CUTTING In China, technology and equipment development of ultrahigh pressure water cutting have been a full twenty years. The first water cutting machine developed by author is 250MPa of pressure, 2.5L/min of flow. And the current main water cutting products which use ultrahigh pressure intensifier or reciprocating pump are 400MPa of pressure, 3L/min of flow [1].
    [Show full text]
  • Ultrahd 2-Door Rolling Workbench
    ASSEMBLY INSTRUCTIONS UltraHD® 2-Door Rolling Workbench (Model No. 20262, 20142, 20152) Granite Graphite Red 77 in. W x 20 in. D x 37.5 in. H (1.95 m W x 50.8 cm D x 95.2 cm H) Reference page 15 for special care and maintenance of stainless steel SC200304 #8 #41 #1 #11 Small #27-B Drawers #40 #12-B #4 #24 #27 #26 #9 #12 #2 Medium Drawer #57 #13 #23 #6 #5 #42 #15 #13-B Large Drawer #20-A #18 #20-B #19 #3 #17 1 2 Small Drawer #26-2 #15 #26-1 Medium Drawer #12-5 #12-2 #12-1 #15 Large Drawer #13-4 #13-2 #13-1 #15 3 PARTS LIST Please check the parts carefully according to the parts list. If you are missing any parts, please contact our customer service department (please see page 15.) (#1) LEFT SIDE PANEL x 1 PC (#2) RIGHT SIDE PANEL x 1PC (#3) FRONT FRAME x 1 PC (#4) BACK FRAME x 1 PC (#5) BASE PANEL x 1 PC (#6) SHELF x 1 PC (#8) SOLID HARDWOOD TOP x 1 PC (#9) PUSH BAR x 2 PCS 34 PARTS LIST Please check the parts carefully according to the parts list. If you are missing any parts, please contact our customer service department (please see page 15.) (#11) LEFT SIDE SLIDER SUPPORT x 1PC (#12-1) MEDIUM-SIZE DRAWER FRONT x 1 PC (#12-2) MEDIUM-SIZE DRAWER BOTTOM PANEL x 1 PC (#12-5) MEDIUM-SIZE DRAWER BACK PANEL x 1 PC (#12-B) WHEEL WITH BRAKE x 2 PCS (#13-B) WHEEL W/O BRAKE x 2 PCS (#13-1) LARGE DRAWER FRONT PANEL x 1 PC (#13-2) LARGE DRAWER BOTTOM PANEL x 1 PC 5 PARTS LIST Please check the parts carefully according to the parts list.
    [Show full text]