Congratulations, Setup Is Complete Quick Start Guide VULKANO FLOW
Total Page:16
File Type:pdf, Size:1020Kb
Quick Start Guide Vulkano Setup for Windows 7 and Vista 1. Connect Vulkano to Your Set-Top Box (STB) Your STB has output connectors on the back for Component, Composite, or both. If you VULKANO FLOW LC Congratulations on buying Vulkano. We will take you through a few simple have both, use Component for better video quality. (You will need a Set-Top Box to use Windows 7 and Vista steps to get you up and running. Vulkano) Connect audio and video cables from the STB “Output” connectors to Vulkano’s video These steps are for setting up your Vulkano from a Windows 7 PC or and audio “Input” connectors as shown. For Component, you will use two cables. For Windows Vista PC. If you are using a Windows XP PC or a Mac, please Composite, you will only use one follow the steps on the other side of this Quick Start Guide. Write down your STB brand and model number. You will need it later in the Setup Component What’s in the Box Compliance note: •Changes or modifications not expressly approved by the party responsible for compliance could void the user ’s authority to operate the equipment. •This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to 2 Composite cables 2 Component cables Vulkano unit radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by oneor moreof the followingmeasures: Composite —Reorientor relocate the receivingantenna. —Increase the separation betweenthe equipmentand receiver. —Connecttheequipmentintoan outleton a circuitdifferentfrom that to whichthe receiverisconnected. —Consultthe dealeror an experienced radio/TVtechnician for help. •The antennas used for this transmitter must be installed to provide a separation distance of at least 20cm Ethernet cable IR blaster cable Power adapter from all personsandmustnot be locatedoroperatinginconjunction with any other antenna or transmitter. •Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device 2. Connect Vulkano to Your TV 3. Power Players PC Your TV has audio and video “Input” connectors on the back or side for Component, Plug the power adapter into Vulkano and a wall plug or power strip as shown • Download Vulkano PC Player to your PC from www.myvulkano.com/players.html Composite, or both. Make sure you use the same cable types, either Component or • Install and run Vulkano Player Composite for this connection as used in Step 1 • Select Run Vulkano Player if you already set up Vulkano using your TV • Enter the name and password of Vulkano Connect audio and video cables from the Vulkano “Output” connectors to your TV’s video • Select Watch TV to get started and audio “Input” connectors as shown. For Component, you will use two cables. For Mac Composite, you will only use one • Download Vulkano Mac Player to your Mac from www.myvulkano.com/players.html 4. Vulkano Player • Install and run Vulkano Player • Go to Player > Add/Select Player > Add to enter the name and password of Vulkano Component Download Vulkano Player from http://www.monsoonmultimedia.com/players.html . Click • Go back to the Home screen and push Watch TV to get started iPhone/iPad on the “Download now” button for the PC Player • Download Vulkano Player to your iPhone or iPad from the App Store • Go to Settings>Select to enter the name and password of Vulkano Save Vulkano Player to your computer • Go back to the Home screen and push Live TV to get started Android After download is complete, run Vulkano Player . (It takes a few minutes to download, • Download Vulkano Player to your phone from Android Market and then a few more minutes to install) • Install and run Vulkano Player • Go to Settings > Selected Vulkano > Add Vulkano When asked, select “Run Vulkano Setup Wizard” • Enter the name and password of Vulkano • Go back to the Home screen and push Live TV to get started Vulkano Setup Wizard will start and lead you through the remaining steps Composite Troubleshooting If your STB is too far from Vulkano, or hidden from it, you can use the included IR Blasters. Plug the pin in the back of Vulkano and place the IR ‘paddles’ in front of the remote window on your STB. If you have wireless setup problems Additional information and technical support available at www.myvulkano.com/support.html If you see the “Network Connection Lost” screen more than once, connect the Ethernet Support cable as described in the Mac/XP Setup process on the back of this Quick Start Guide 9:00 AM to 9:00 PM PST (Monday – Friday) phone: +1 (866) 937-4282 e-mail: [email protected] Congratulations, setup is complete Vulkano Setup for Windows XP and Mac 1. Network and Power Quick Start Guide Congratulations on buying Vulkano. We will take you through a few simple During this first portion of the setup, we will use an Ethernet cable to connect to your steps to get you up and running. Vulkano to your home WiFi network. Once it is on the network we will disconnect the cable Vulkano3 Flow Vulkano3 Stream and Vulkano can be used wirelessly These steps are for setting up your Vulkano from a Windows XP PC or Use the included Ethernet cable to connect from Vulkano to an open Ethernet connection; Mac. If you are using a Windows 7 PC or a Windows Vista PC, please either to your router, your PC or an open Ethernet connection on your network follow the steps on the other side of this Quick Start Guide. If you have an Ethernet connection close to your STB, use this connection. Otherwise, move your Vulkano for this part of the setup. We will move it close to your STB in a few minutes If you do not have an open port, you should purchase a 4-port Ethernet switch or hub What’s in the Box Windows XP and Mac 2 Composite cables 2 Component cables Vulkano unit Plug the power adapter into Vulkano and a wall plug or power strip Ethernet cable PC or Ethernet cable IR blaster cable Power adapter Router 2. PC Player Mac Player 3. Connect Vulkano to Your Set-Top Box (STB) 4. Connect Vulkano to Your TV Download Vulkano Player from Download Vulkano Player from Your STB has output connectors on the back for Component, Composite, or both. If you Your TV has audio and video “Input” connectors on the back or side for Component, http://www.monsoonmultimedia.com/players.h http://www.monsoonmultimedia.com/pla have both, use Component for better video quality. (You will need a Set Top Box to use Composite, or both. Make sure you use the same cable types, either Component or tml and save it to your computer yers.html Vulkano) Composite for this connection as used in Step 1 Connect audio and video cables from the Vulkano “Output” connectors to your TV’s video After download is complete, run Vulkano After download is complete, install Connect audio and video cables from the STB “Output” connectors to Vulkano’s video and audio “Input” connectors as shown. For Component, you will use two cables. For Player. (It takes a few minutes to download, Vulkano Player. (It takes a few minutes and audio “Input” connectors as shown. For Component, you will use two cables. For Composite, you will only use one and then a few more minutes to install) to download, and then a few more Composite, you will only use one minutes to install) When asked, select “Run Vulkano Setup Write down your STB brand and model number. You will need it later in the Setup Component Wizard” When Vulkano Player starts, select Player > Run Vulkano Setup Component Vulkano Setup Wizard will start and lead you through the setup Vulkano Setup Wizard will start and lead you through the setup When the Setup Wizard tells you to “***”, move Vulkano close to your STB, if it is not When the Setup Wizard tells you to already there. It is OK to unplug the power “***”, move Vulkano close to your STB, and Ethernet connections from Vulkano if it is not already there. It is OK to Composite unplug the power and Ethernet If you moved Vulkano, reconnect the power connections from Vulkano in the new location If you moved Vulkano, reconnect the Composite Complete the cable connections described power in the new location in Steps 3 and 4 Complete the cable connections After the cables are connected, hit “Next” described in Steps 3 and 4 on the Vulkano Setup Wizard and complete the remaining steps After the cables are connected, hit 5. Finish Setup Wizard “Next” on the Vulkano Setup Wizard and complete the remaining steps Hit “Next” on the Vulkano Setup Wizard and complete the remaining steps Congratulations, setup is complete.