Magnet-Decision Support/ Roll the Dice Machine Tools Required
Total Page:16
File Type:pdf, Size:1020Kb
117.835 Magnet-Decision Support/ Roll The Dice Machine Tools Required: ø15 sandpaper drill superglue wood glue pliers round nose machine vice bending aid pliers slot screwdri- fretsaw adhesive tape pricking awl ver Please Note! The OPITEC range of projects is not intended as toys for young children. They are teaching aids for young people learning the skills of Craft, Design and Technology. These projects should only be under- taken and operated with the guidance of a fully qualified adult. The finished projects are not suitable to give to children under 3 years old. Some parts can be swallowed. Danger of suffocation! Parts List Quantity Size (mm) Designation Part No. MDF Board 1 100x100x8 Base Plate 1 Welding Wire 1 250x2 Pendulum Holder 2 Welding Wire 1 250x1 Pendulum 3 Luster Clamp Insert with Cross Hole 1 Pendulum Holder Fixing 4 Cylinder Head Screw 2 2 3x8 Fixing 5 Disc Magnet 8 ø15x6 Magnet 6 1 Instructions 117.835 Magnet- Decision Support/ Roll The Dice Machine 2 Instructions 117.835 Magnet- Decision Support/ Roll The Dice Machine Please Note: There are two options for fixing the magnets. Variant 1: Magnets are glued to the base plate. Variant 2: Magnets are sunk into the base plate. We describe variant 2. When the pendulum is bent, a final distinction between the variants must be made. 1 Variant 2 2 ø15 1 Attach the template (page 5) to the base plate (1) with adhesive tape. Drill the ø 15mm holes 6mm deep as shown in the figure. Resign from Mark the center points for the magnets with the pricking awl. Also drilling in variant 1. The magnets are glued to the base plate. mark the corner points of the recess for the pendulum holder and then sketch the recess. 3 4 S S S N S 8 S S Saw out the recess with the fretsaw. Glue the magnets (8) into the holes with superglue as shown. Observe Please Note: Size must be observed! the polarity. 5 6 2 4 Glue the luster clamp insert (4) into the provided recess by using Bend the pendulum holder (2) according to the bending template superglue as shown and screw the screws (5) into the thread. (page 7) and insert it into the luster clamp insert (4). Place it vertically. Tighten the screws (5). 3 Instructions 117.835 Magnet- Decision Support/ Roll The Dice Machine 7 8 3 S N Bend the pendulum (3) according to the bending template (page 7). Cut out a template (decision support/ dice machine) and place as Glue the last magnet (8) north pole downwards (homopolar to the shown. Done! center magnet) to the pendulum support. Then attach the pendulum in the pendulum holder. Done! Bending Template S 1:1 Bending Template Pendulum - Sunk Magnets Bending Template Pendulum - Affixed Magnets 4 Instructions 117.835 Magnet- Decision Support/ Roll The Dice Machine Magnet- Decision Support/ Roll The Dice Machine Template Magnet Subdivision + Recess S 1:1 Bending Template Pendulum Arm S 1:1 5 6 Instructions 117.835 Magnet- Decision Support/ Roll The Dice Machine S 1:1 Dice Machine Variant 2 Decision Support Variant 2 7 Instructions 117.835 Magnet- Decision Support/ Roll The Dice Machine S 1:1 Dice Machine Variant 1 Decision Support Variant 1 8 Instructions 117.835 Magnet- Decision Support/ Roll The Dice Machine Individual Creation S 1:1 Variant 1 Variant 2 9.