International Standards in process

ISO/DTS Reclaimed isobutene-isoprene (IIR) rubber — 16096 Evaluation procedure An International Standard is the result of an agreement between the member bodies of ISO. A first important step towards an International TC 48 Laboratory equipment Standard takes the form of a committee draft (CD) - this is circulated ISO/CD 384 Laboratory glass and plastics ware — Princi - for study within an ISO technical committee. When consensus has ples of design and construction of volumetric been reached within the technical committee, the document is sent to instruments the Central Secretariat for processing as a draft International Stand - ard (DIS). The DIS requires approval by at least 75 % of the member ISO/CD 3819 Laboratory glassware — Beakers bodies casting a vote. A confirmation vote is subsequently carried ISO/CD 4796-1 Laboratory glassware — Bottles — Part 1: out on a final draft International Standard (FDIS), the approval criteria Screw-neck bottles remaining the same. ISO/CD 16496 Laboratory glassware — Devices with vacuum- jacket insulation TC 58 Gas cylinders

ISO 11119- Gas cylinders — Refillable composite gas cyl - 2:2012/CD inders and tubes — Design, construction and Amd 1 testing — Part 2: Fully wrapped fibre reinforced composite gas cylinders and tubes up to 450 l CD registered with load-sharing metal liners — Amendment 1 TC 61 Plastics ISO/DTR Standard table for reference global solar spec - Period from 01 April to 30 April 2013 17801 tral irradiance at sea level — Horizontal, relative air mass 1 These documents are currently under consideration in the technical committee. ISO/DTR Plastics — Calculation of the goodness of fit of 18486 the spectral distribution of a solar simulator to They have been registred at the Central Secretariat. a reference solar spectral distribution

ISO/CD Plastics — Mixed polypropylene (PP) and poly - COPOLCO Committee on consumer policy 18263-1 ethylene (PE) recyclate — Part 1: Designation system and basis for specifications ISO/IEC CD Safety aspects — Guidelines for child safety Guide 50 ISO/CD Plastics — Mixed polypropylene (PP) and poly - 18263-2 ethylene (PE) recyclate — Part 2: Preparation of TC 17 Steel test specimens and determination of properties ISO/CD 18203 Steels — Determination of the thickness of surface-hardened layers TC 68 Financial services Mobile Financial Services — Part 5: Mobile TC 20 Aircraft and space vehicles ISO/CD 12812-5 Person-to-Business Payments ISO/CD 16164 Space Systems — Disposal of satellites oper- ISO/CD Mobile Financial Services — Part 6: General ating in or crossing Low Earth Orbit 12812-6 Mobile Banking operations TC 22 Road vehicles TC 71 Concrete, reinforced concrete and pre- ISO/CD Road vehicles — Unified diagnostic services stressed concrete 14229-7 (UDS) — Part 7: Unified diagnostic services on Local Interconnect Network implementation ISO/CD Test Methods for Pervious Concrete — Part 1: (UDSonLIN) 17785-1 Permeability ISO/CD 17840 Road vehicles — Vehicle extrication card / TC 76 Transfusion, infusion and injection, and Rescue Sheet blood processing equipment for medi - cal and pharmaceutical use TC 23 Tractors and machinery for agriculture and forestry ISO/CD 1135-4 Transfusion equipment for medical use — Part 4: Transfusion sets for single use ISO/CD 3600 Tractors, machinery for agriculture and forestry, powered lawn and garden equipment — Op - ISO/CD 1135-5 Transfusion equipment for medical use — Part erator's manuals — Content and presentation 5: Transfusion sets for single use with pressure infusion apparatus TC 38 Textiles TC 79 Light metals and their alloys ISO/CD 18074 Textiles — Identification of some animal fibres by DNA analysis method- Cashmere, wool, yak ISO/CD 16374 Evaluation method for cleanness of magnesium and their blends and magnesium alloy ingots TC 41 Pulleys and belts (including veebelts) TC 85 Nuclear energy, nuclear technologies, and radiological protection ISO/CD 13050 Curvilinear toothed synchronous belt drive systems ISO/CD Nuclear energy — Vocabulary — Part 3: Nu - 12749-3 clear fuel cycle TC 42 Photography ISO/CD 8769 Reference sources — Calibration of surface ISO/CD 17850 Photography — Digital cameras — Geometric contamination monitors — Alpha-, beta- and distortion (GD) measurements photon emitters TC 45 Rubber and rubber products ISO/CD Measurement of radioactivity in the environ - ISO/DTS Reclaimed rubber derived from products 18589-2 ment — Soil — Part 2: Guidance for the selec - 16095 containing mainly natural rubber — Evaluation tion of the sampling strategy, sampling and procedure pre-treatment of samples

ISO Upd ate, Supplement to ISO Focus -- May 2013 1 TC 94 Personal safety -- Protective clothing ISO/DPAS Textile floor coverings — Installation practice and equipment 18167 ISO/CD Protective clothing against heat and flame — TC 223 Societal security 13506-1 Part 1: Test method for complete garments ISO/DTR Societal security — Emergency manage - — Prediction of absorbed energy using an 22351 ment — Message structure for exchange of instrumented manikin information ISO/CD Respiratory protective devices — Methods of TC 244 Industrial furnaces and associated 16900-14 test and test equipment — Part 14: Measure- ment of sound level processing equipment ISO/CD Industrial furnace and associated processing ISO/CD Respiratory protective devices — Part 1: Selec - 13577-3 equipement — Safety — Part 3: Generation and 16975-1 tion, use and maintenance use of protective and reactive atmosphere TC 96 Cranes gases ISO/CD 4302 Cranes — Wind load assessment TC 258 Project, programme and portfolio TC 104 Freight containers management ISO/CD Freight containers — Electronic seals — Part 3: ISO/CD 21502 Project and Programme Portfolio Management 18185-3 Environmental characteristics JTC 1 Information technology TC 107 Metallic and other inorganic coatings ISO/IEC Information technology — Implementation and ISO/CD 11177 Vitreous and porcelain enamels — Inside and 14763-2:2012/ operation of customer premises cabling — Part outside enamelled valves and pressure pipe PDAM 1 2: Planning and installation — Amendment 1 fittings for untreated and potable water supply ISO/IEC Information technology — High efficiency — Quality requirements and testing 23008-2/ coding and media delivery in heterogeneous TC 110 Industrial trucks PDAM 1 environments

ISO/CD Rough-terrain trucks — User requirements — — Part 2: High efficiency video coding — 11525-4 Part 4: Requirements for trucks operating with Amendment 1: Range extensions freely swinging loads ISO/IEC Information technology — High efficiency ISO/CD Rough-terrain trucks — User requirements — 23008-2/ coding and media delivery in heterogeneous 11525-5 Part 5: Interface between rough-terrain truck PDAM 2 environments and integrated personnel work platform ISO/CD Rough-terrain trucks — Non-integrated — Part 2: High efficiency video coding — Amendment 2: Multiview extensions 18479-2 personnel work platforms — Part 2: User requirements ISO/IEC CD Information technology — High efficiency TC 113 Hydrometry 23008-5 coding and media delivery in heterogeneous environments ISO/DTR Estimation of sediment deposition in reservoir 11651 using one dimensional simulation models — Part 5: HEVC Conformance testing and ISO/DTR Artificial recharge to groundwater reference software 13973 ISO/IEC CD Information Technology — Real Time Locat - TC 146 Air quality 24769-61 ing System (RTLS) Device Conformance Test Methods — Part 61: Low rate pulse repetition ISO/CD 17621 Workplace atmospheres — Short term detector frequency Ultra Wide Band (UWB) air interface tube measurement systems — Requirements and test methods ISO/IEC CD Information Technology — Real Time Locat - ing 24769-62 System (RTLS) Device Conformance Test TC 165 Timber structures Methods — Part 62: High rate pulse repetition ISO/CD 18324 Timber structures — Test methods — Floor frequency Ultra Wide Band (UWB) air interface vibration ISO/IEC CD Information technology — Real Time Locat - ing TC 173 Assistive products for persons with 24770-61 Systems (RTLS) device performance test methods — Part 61: Low rate pulse repetition disability frequency Ultra Wide Band (UWB) air interface ISO/CD 7176-8 Wheelchairs — Part 8: Requirements and Information technology — Real Time Locat - ing test methods for static, impact and fatigue ISO/IEC CD 24770-62 Systems (RTLS) device performance test strengths methods — Part 62: Low rate pulse repetition ISO/CD Wheelchair seating — Part 11: The determina - frequency Ultra Wide Band (UWB) air interface 16840-11 tion of perspiration dissipation characteristics of seat cushions intended to manage tissue integrity TC 206 Fine ceramics

ISO/CD 17162 Fine ceramics (advanced ceramics, advanced technical ceramics) — Mechanical properties of monolithic ceramics at room temperature — Determination of compressive strength DIS circulated ISO/CD 17170 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for sphere indentation of porous ceramics Period from 01 April to 30 April 2013 TC 219 Floor coverings These documents have obtained substantial support within the ap - propriate ISO technical committee. ISO/CD 16905 Resilient floor coverings — Specification for rubber floor covering — Tile/Plank They have been submitted to the ISO member bodies for voting by the date shown. ISO/CD 16906 Resilient Floor Covering — Determination of seam strength * Available in English only

2 ISO Upd ate, Supplement to ISO Focus -- May 2013

ISO/DIS 17786 * Dimethyl ether (DME) for fuels Vote — Determination of evapora - 2013-07-09 terminates tion residues — Mass analysis method COPOLCO Committee on consumer TC 31 Tyres, rims and valves policy ISO/DIS * Earth-mover tyres and rims — ISO/IEC Safety aspects — Guidelines for 4250-1 Part 1: Tyre designation and 2013-07-13 DGuide 51 their inclusion in standards 2013-08-17 dimensions (Revision of ISO 4250-1:2006) (Revision of ISO/IEC Guide ISO/DIS * Earth-mover tyres and rims 4250-2 — Part 2: Loads and inflation 2013-07-13 5 pressures 1:1999) (Revision of ISO 4250-2:2006) TC 17 Steel ISO/DIS 683-4 * Heat-treatable steels, alloy steels and free-cutting steels — Part 4: 2013-07-03 TC 34 Food products Free-cutting steels ISO/DIS 2451 * Cocoa beans — Specification (Revision of ISO 683-9:1988) 2013-07-06 ISO/DIS * Heat-treatable steels, alloy steels 683-18 and free-cutting steels — Part 2013-07-05 (Revision of ISO 2451:1973) 18: Bright steel products ISO/DIS * Rice — Determination of amyl - 6647-1 ose content — Part 1: Reference 2013-09-12 ( method Revision of ISO 683-18:1996) TC 20 Aircraft and space vehicles (Revision of ISO 6647 -1:2007) ISO/DIS 11077 * Aerospace — Self-propelled de-icing/anti-icing vehicles — 2013-07-18 ISO/DIS * Rice — Determination of amyl -

Functional requirements 6647-2 ose content — Part 2: Routine 2013-09-12 (Revision of ISO 11077:1993) methods (Revision of ISO 6647-2:2007) ISO/DIS 8278 * Aerospace — Hydraulic, pres - sure compensated, variable 2013-07-17 ISO/DIS * Milk and milk products - Deter- 8968-1 mination of nitrogen content and 2013-09-05 delivery pumps — General requirements crude protein calculation — Part (Revision of ISO 8278:1986) 1: Kjeldahl principle (Revision of ISO 5549:1978, ISO ISO/DIS 9206 * Aerospace — Constant displace - 8968-1:2001, ISO 8968-2:2001) ment hydraulic motors — Gen - eral 2013-07-04 specifications ISO/DIS * Microbiology of food and animal (Revision of ISO 9206:1990) 16649-3 feeding stuffs — Horizontal 2013-09-19 method for the enumeration of TC 22 Road vehicles beta-glucuronidase-positive ISO/DIS * Road vehicles — Fuse-links — Escherichia coli — Part 3: Detec - 8820-10 Part 10: Fuse-links with tabs tion and most probable number Type L (high current miniature) technique using 5-bromo-4-chlo - ro-3-indolyl-beta-D-glucuronide ISO/DIS * Road vehicles — Vehicle test (Revision of ISO/TS 11451-3 methods for electrical dis - 2013-07-25 16649-3:2005) turbances from narrowband radiated electromagnetic energy ISO * Animal and vegetable fats and — Part 3: On-board transmitter 5555:2001/ oils — Sampling — Amendment 2013-09-19 simulation DAmd 1 1 (Revision of ISO 11451-3:2007) ISO/DIS * Determination of individual and ISO/DIS * Road vehicles — Controller area 12228-1 total sterols contents — Gas 2013-09-26 16845-2 network (CAN) — Conformance 2013-07-20 chromatographic method — Part test plan — Part 2: High-speed 1: Animal and vegetable fats medium access unit with selec - and oils tive wake-up functionality — (Revision of ISO 12228:1999) Conformance test plan TC 38 Textiles TC 24 Particle characterization ISO/DIS 16533 * Textiles — Measurement of including sieving exothermic and endothermic 2013-07-13 ISO/DIS * Particle size analysis — Image properties of textiles under 13322-1.2 analysis methods — Part 1: 2013-06-23 humidity change Static image analysis methods TC 42 Photography (Revision of ISO 13322-1:2004) ISO/DIS 18943 * Imaging materials — Magnetic TC 28 Petroleum products and hard drives used for image stor- 2013-07-30 lubricants age — Care and handling ISO/DIS 17196 * Dimethyl ether (DME) for fuels ISO/DIS 18944 * Imaging materials — Reflec - — Determination of impurities — 2013-07-09 tion colour photographic prints 2013-07-23 Gas chromatographic method — Test print construction and measurement ISO/DIS 17197 * Dimethyl ether (DME) for fuels — (Revision of ISO 18944:2012) Determination of water content 2013 -07 -09 Acoustics — Karl Fischer titration method TC 43 ISO/DIS 17198 * Dimethyl ether (DME) for fuels ISO/DIS * Acoustics — Soundscape — — Determination of total sulfur, 2013-07-09 12913-1 Part 1: Definition and conceptual 2013-07-23 ultraviolet fluorescence method framework

ISO Upd ate, Supplement to ISO Focus -- May 2013 3 ISO 10140- * Acoustics — Laboratory meas - ISO/DIS 3064 * Essential oil of petitgrain, Para - 3:2010/DAmd urement of sound insulation 2013-09-05 guayan type (Citrus aurantium 2013-07-18 1 of building elements — Part 3: L. ssp. aurantium, syn. Citrus Measurement of impact sound aurantium L. ssp. amara var. insulation — Amendment 1 pumilia) (Revision of ISO 3064:2000) TC 44 Welding and allied TC 58 Gas cylinders processes ISO/DIS 17533 * Welding for aerospace applica - ISO/DIS 10286 * Gas cylinders — Terminology tions — Welding data in design 2013-07-23 2013-09-26 documents (Revision of ISO 10286:2007) TC 45 Rubber and rubber products ISO/DIS * Gas cylinders — Non-refillable 11118.2 metallic gas cylinders — Specifi - 2013-06-27 ISO/DIS 1823 * Rubber hose assemblies for oil cation and test methods suction and discharge service (Revision of ISO 11118:1999) — Specification (Revision of ISO 1823-1:1997, TC 61 Plastics ISO 1823-2:1997) ISO/DIS 13927 * Plastics — Simple heat release ISO/DIS 249 * Rubber, raw natural — Determi - test using a conical radiant 2013-09-19 nation of dirt content 2013-07-20 heater and a thermopile detector (Revision of ISO 13927:2001) (Revision of ISO 249:1995) ISO/DIS 17223 * Plastics — Determination of ISO/DIS 1656 * Rubber, raw natural, and rubber yellowness index and change in 2013-07-09 latex, natural — Determination of 2013-07-20 yellowness index nitrogen content ISO/DIS * Plastics — Determination of (Revision of ISO 1656:1996) 22007-6 thermal conductivity and thermal 2013-07-09 ISO/DIS * Rubber — Determination of diffusivity — Part 6: Comparative 6101-3 metal content by atomic absorp - 2013-07-20 method for low thermal con - tion spectrometry — Part 3: ductivities using a temperature- Determination of copper content modulation technique (Revision of ISO 6101-3:1997) TC 69 Applications of statistical ISO/DIS * Rubber — Determination of methods 6101-4 metal content by atomic absorp - 2013-07-20 ISO/DIS * Control charts — Part 1: General tion spectrometry — Part 4: 7870-1 guidelines 2013-07-30 Determination of manganese content (Revision of ISO 7870-1:2007) (Revision of ISO 6101-4:1997) TC 83 Sports and recreational ISO/DIS 124 * Latex, rubber — Determination of total solids content 2013-07-06 equipment ISO/DIS 11110 * Winter-sports equipment — Test (Revision of ISO 124:2011) devices for the setting of the 2013-07-03 ISO/DIS 976 * Rubber and plastics — Polymer functional unit ski/boot/binding dispersions and rubber latices — 2013-07-06 — Requirements and tests Determination of pH (Revision of ISO 11110:1997) (Revision of ISO 976:1996, ISO ISO/DIS 13992 * Alpine touring ski-bindings — 976:1996/Amd 1:2006) Requirements and test methods 2013-07-03 ISO/DIS 2322 * Styrene-butadiene rubber (SBR) (Revision of ISO 13992:2006) — Emulsion- and solution- 2013-07-09 polymerized types — Evaluation TC 85 Nuclear energy, nuclear procedures technologies, and radio - (Revision of ISO 2322:2009) logical protection ISO/DIS 2393 * Rubber test mixes — Prepara - ISO/ASTM DIS * Practice for use of thermolu - tion, mixing and vulcanization — 2013-07-09 51956 minescence dosimetry (TLD) Equipment and procedures systems for radiation processing (Revision of ISO 2393:2008) (Revision of ISO/ASTM ISO/DIS 2476 * Butadiene rubber (BR) — Solu - 51956:2005) tion-polymerized types — Evalu - 2013-07-09 ISO/ASTM DIS * Standard practice for dosimetry ation procedures 52628 in radiation processing 2013-07-19 (Revision of ISO 2476:2009)

ISO/DIS * Flexible cellular polymeric mate - ISO/ASTM DIS * Guide for performance char- 3385.2 rials — Determination of fatigue by 2013-06-19 52701 acterization of dosimeters and 2013-07-19 constant-load pounding dosimetry systems for use in (Revision of ISO 3385:1989) radiation processing TC 46 Information and TC 91 Surface active agents documentation ISO/DIS * Surface active agents — Deter- ISO/DIS 16439 * Methods and procedures for as - 17293-1 mination of chloroacetic acid 2013-07-30 sessing the impact of libraries 2013-07-27 (chloroacetate) in surfactants — Part 1: HPLC method TC 54 Essential oils

4 ISO Upd ate, Supplement to ISO Focus -- May 2013 ISO/DIS * Surface active agents — Deter- TC 131 Fluid power systems 17293-2 mination of chloroacetic acid 2013-07-30 (chloroacetate) in surfactants — ISO/DIS * Hydraulic fluid power — Fa - 10771-1 tigue pressure testing of metal 2013-07-30 Part 2: Ionic Chromatographic pressure-containing envelopes method — Part 1: Test method TC 94 Personal safety -- Pro- (Revision of ISO 10771-1:2002) tective clothing and TC 135 Non-destructive testing equipment ISO/DIS * Non-destructive testing — Char- ISO/DIS * Protective clothing for use in 18563-1 acterization and verification of 2013-09-12 11611.2 welding and allied processes 2013-06-26 ultrasonic phased array equip - ment — Part 1: Instruments (Revision of ISO 11611:2007) TC 138 Plastics pipes, fittings and * Protective clothing — Cloth - ing ISO/DIS valves for the transport of 11612.2 to protect against heat and flame 2013-06-26 — Minimum performance fluids requirements ISO/DIS 15494 * Plastics piping systems for (Revision of ISO 11612:2008) industrial applications — Polybu - 2013-09-05 * Protective clothing — Protection tene (PB), polyethylene (PE) and ISO/DIS polypropylene (PP) — Specifica - against heat and flame — Lim - ited 14116.2 2013-06-26 tions for components and the flame spread materials, material system — Metric series assemblies and clothing (Revision of ISO 15494:2003) (Revision of ISO 14116:2008, ISO 14116:2008/Cor 1:2009) ISO/DIS 7509 * Plastics piping systems — Glass-reinforced thermosetting 2013-07-13 TC 102 Iron ore and direct reduced plastics (GRP) pipes — Deter- iron mination of time to failure under ISO/DIS 16742 * Iron ores — Sampling of slurries sustained internal pressure 2013-07-06 (Revision of ISO 7509:2000) TC 142 Cleaning equipment for air TC 106 Dentistry and other gases ISO/DIS 16443 Dentistry — Vocabulary of oral ISO/DIS 15957 * Loading dusts for testing air implantology 2013-09-26 cleaning equipment 2013-09-05

ISO/DIS 11499 * Dentistry — Single-use cartridg - TC 146 Air quality es for local anaesthetics 2013-09-19 ISO/DIS * Stationary source emissions — 14385-1 Green house gases — Part 1: 2013-07-23 (Revision of ISO 11499:2007) Calibration of automated meas - ISO/DIS 17730 * Dentistry - Fluoride Varnishes uring systems 2013-09-05 ISO/DIS * Stationary source emissions — 14385-2 Green house gases — Part 2: 2013-07-23 TC 108 Mechanical vibration, Ongoing quality control of auto - shock and condition mated measuring systems monitoring TC 147 Water quality ISO/DIS * Methods for the calibration of ISO/DIS 16780 * Water Quality — Determination of 16063-16 vibration and shock transducers 2013-07-13 polychlorinated naphthalenes 2013-07-09 — Part 16: Calibration by Earth's (PCN) — Method using gas gravitation chromatography (GC) and mass (Revision of ISO 5347-5:1993) spectrometry (MS) TC 121 Anaesthetic and respiratory TC 150 Implants for surgery equipment ISO/DIS * Implants for surgery - Plasma- ISO/DIS 17256 * Anaesthetic and respira - 13179-1.2 sprayed unalloyed titanium coat - 2013-06-23 tory equipment — Respiratory 2013-07-27 ings on surgical implants — Part therapy tubing and connectors 1: General requirements ISO/DIS * Medical supply units ISO/DIS * Implants for surgery — Active 11197.2 2013-06-05 14708-1 implantable medical devices — 2013-07-23 Part 1: General requirements for (Revision of ISO 11197:2004) safety, marking and for infor- mation to be provided by the ISO/DIS * Systems for evacuation of plume 16571.2 generated by medical devices 2013-06-19 manufacturer (Revision of ISO 14708-1:2000)

TC 130 Graphic technology TC 161 Control and protective devices for gas and/or oil ISO/DIS * Graphic technology — Process 12647-5 control for the manufacture of 2013-07-23 burners and appliances half-tone colour separations, ISO/DIS * Safety and control devices for proof and production prints — 23551-5 gas burners and gas-burning 2013-07-05 Part 5: Screen printing appliances — Particular require- (Revision of ISO 12647-5:2001) ments — Part 5: Manual gas ISO/DIS 15341 * Graphic technology — Method valves for Radius Determination of 2013-07-20 TC 163 Thermal performance and Printing Cylinders energy use in the built environment

ISO Upd ate, Supplement to ISO Focus -- May 2013 5

ISO/DIS * Thermal insulation — Building ISO 8124- * Safety of toys — Part 1: Safety 9869-1 elements — In-situ measure- 2013-07-09 1:2012/DAmd aspects related to mechani - 2013-07-03 ment of thermal resistance and 2 cal and physical properties — thermal transmittance — Part 1: Amendment 2: Impaction and Heat flow meter method impalement hazards (Revision of ISO 9869:1994) ISO 8124- * Safety of toys — Part 1: Safety TC 164 Mechanical testing of 1:2012/DAmd aspects related to mechani - 2013-07-09 metals 3 cal and physical properties — Amendment 3: Cords ISO/DIS * Metallic materials — Tensile test - ISO 8124- * Safety of toys — Part 4: Swings, 6892-3 ing — Part 3: Method of test at 2013-09-05 low temperature 4:2010/DAmd slides and similar activity toys 2013-07-03 (Revision of ISO 15579:2000) 2 for indoor and outdoor family domestic use — Amendment 2: ISO/DIS * Metallic materials — Verifica - Paddling pools 7500-1 tion of static uniaxial testing 2013-09-05 machines — Part 1: Tension/ TC 182 Geotechnics compression testing machines ISO/DIS * Geotechnical investigation and — Verification and calibration of 17892-1 testing — Laboratory testing of 2013-09-12 the force-measuring system soil — Part 1: Determination of (Revision of ISO 7500-1:2004, water content ISO 7500-1:2004/Cor 1:2008) (Revision of ISO/TS 17892- TC 171 Document management 1:2004, ISO/TS 17892-1:2004/ applications Cor 1:2006) ISO/DIS * Electronic imaging — Test target ISO/DIS * Geotechnical investigation and 12653-3 for scanning of office documents 2013-06-19 17892-2 testing — Laboratory testing of 2013-09-12 — Part 3: Test target for use in soil — Part 2: Determination of lower resolution applications density of fine-grained soil (Revision of ISO/TS 17892- ISO/DIS * Electronic imaging — Vocabulary 2:2004, ISO/TS 17892-2:2004/ 12651-2 — Part 2: Document workflow 2013-07-20 Cor 1:2006)

(Revision of ISO 12651:1999) TC 189 Ceramic tile

TC 172 Optics and photonics ISO/DIS * Ceramic tiles — Part 4: Determi - 10545-4 nation of modulus of rupture and 2013-09-26 ISO/DIS 17411 * Optics and photonics — Opti - breaking strength cal materials and components 2013-07-16 (Revision of ISO 10545-4:2004) — Test method for homogene - ity of optical glasses by laser ISO/DIS * Ceramic tiles — Part 8: De - interferometry 10545-8 termination of linear thermal 2013-09-26 expansion ISO/DIS 11978 * Ophthalmic optics — Contact (Revision of ISO 10545-8:1994) lenses and contact lens care 2013-09-12 products — Labelling TC 190 Soil quality (Revision of ISO 11978:2000) ISO/DIS * Soil quality - Acid-base account - ISO/DIS * Ophthalmic implants — Intraocu - 14388-3 ing procedure for acid sulfate soils 2013-07-23 11979-6 lar lenses — Part 6: Shelf-life 2013-09-26 — Part 3: Suspension peroxide and transport stability oxidation combined acidity and (Revision of ISO 11979-6:2007) sulfur (SPOCAS) suite analysis ISO/DIS 13212 * Ophthalmic optics — Contact lens care products — Guidelines 2013-09-26 ISO/DIS 17182 * Soil quality — Determination for determination of shelf-life of some selected phenols and 2013-07-12 (Revision of ISO 13212:2011) chlorophenols — Gas chroma - tographic method with mass IEC/DIS Medical electrical equipment spectrometric detection 80601-2-58 — Part 2-58: Particular require- 2013-07-17 ments for basic safety and ISO/DIS 18227 * Soil quality — Determination of essential performance of lens elemental composition by X-ray 2013-07-23 fluorescence removal devices and vitrectomy devices for ophthalmic surgery ISO/DIS 16198 * Soil quality — Plant-based (Revision of IEC biotest to assess the environ - 2013-09-19 80601-2-58:2008) mental bioavailability of trace elements to plants ISO/DIS * Lasers and laser-related equip - 11151-1 ment — Standard optical com - 2013-09-19 TC 192 Gas turbines ponents — Part 1: Components for the UV, visible and near-infra - ISO/DIS 19372 * Microturbines applications red spectral ranges — Safety 2013-07-03 (Revision of ISO 11151-1:2000) ISO/DIS * Lasers and laser-related equip - TC 193 Natural gas 11151-2 ment — Standard optical com - 2013-09-19 ISO/DIS 16960 * Natural gas — Determination of ponents — Part 2: Components sulfur compounds — Determina - 2013-09-19 for the infrared spectral range tion of total sulfur by oxidative (Revision of ISO 11151-2:2000) microcoulometry method TC 181 Safety of toys TC 204 Intelligent transport systems ISO/DIS 21217 * Intelligent transport systems — Communications access for land 2013-07-17 mobiles (CALM) — Architecture

6 ISO Upd ate, Supplement to ISO Focus -- May 2013 (Revision of ISO 21217:2010) (Revision of ISO/IEC 2382- 1:1993, ISO 2382-2:1976, ISO TC 209 Cleanrooms and associat - 2382-3:1987, ISO 2382-6:1987, ed controlled environments ISO/IEC 2382-7:2000, ISO/IEC ISO/DIS * Cleanrooms and associated 2382-8:1998, ISO 2382-12:1988, 14644-12 controlled environments — Part 2013-09-05 ISO/IEC 2382-13:1996, ISO/IEC 12: Classification of air cleanli - 2382-14:1997, ISO/IEC 2382- ness by nanoscale particle 15:1999, ISO/IEC 2382-16:1996, concentration ISO 2382-19:1989, ISO/IEC 2382-20:1990, ISO 2382- TC 213 Dimensional and geometri - 21:1985, ISO/IEC 2382-23:1994, cal product specifications ISO/IEC 2382-24:1995, ISO/IEC and verification 2382-25:1992, ISO/IEC 2382- ISO * Geometrical Product Specifica - 26:1993, ISO/IEC 2382-27:1994, 4287:1997/ tions (GPS) — Surface tex - 2013-09-12 ISO/IEC 2382-28:1995, ISO/IEC DAmd 2 ture: Profile method — Terms, 2382-29:1999, ISO/IEC 2382- definitions and surface texture 9:1995, ISO/IEC 2382-31:1997, parameters — Amendment 2: ISO/IEC 2382-32:1999, ISO/IEC Parameters Xsm and Xc 2382-34:1999, ISO/IEC 2382- 18:1999, ISO/IEC 2382-4:1999, TC 215 Health informatics ISO/IEC 2382-5:1999, ISO/IEC ISO/DIS * Health informatics — Medical 2382-17:1999, ISO/IEC 2382- 22077-1 waveform format — Part 1: 2013-07-27 36:2008, ISO/IEC 2382-37:2012, Encoding rules ISO/IEC 2382-36:2008/Cor (Revision of ISO/DIS 1:2012, ISO/IEC 2382-36:2008/ 11073-92001) DAmd 1) ISO/IEC * Identification cards — Contact - TC 226 Materials for the produc - tion of primary aluminium 14443-2:2010/ less integrated circuit cards — 2013-07-17 DAmd 5 Proximity cards — Part 2: Radio ISO/DIS 18142 * Carbonaceous materials for the frequency power and signal production of primary aluminium 2013-07-09 interface — Amendment 5: Bit — Baked carbon bodies — rates of 3fc/4, fc, 3fc/2 and 2fc Determination of the dynamic from PCD to PICC elasticity modolus by the reso - * Information technology — Secu - nance method ISO/IEC DIS 24759 rity techniques — Test require- 2013-07-05 ISO/DIS 23201 * Aluminium oxide primarily used ments for cryptographic modules for production of aluminium — 2013-07-09 (Revision of ISO/IEC Determination of trace elements 24759:2008) — Wavelength dispersive X-ray

neric coding of moving pictures method 13818-1/ 2013-07-09 DAmd 4 and associated audio informa - TC 232 Learning services outside tion: Systems — Part 1: — formal education Amendment 4: Support for event ISO/DIS * Language learning services signalling in Transport Stream in MPEG-2 systems 29991-1 outside formal education — Re - 2013-07-06 quirements — Part 1: ISO/IEC * Information technology — Cod - 14496-3:2009/ ing of audio-visual objects — 2013-07-13 TC 249 Traditional chinese DAmd 4 Part 3: Audio — Amendment 4: medicine New levels for AAC profiles * Traditional Chinese medicine — ISO/DIS ISO/IEC * Information technology — Cod - 17217-1 Ginseng seeds and seedlings — 2013-07-06 14496- ing of audio-visual objects 2013-07-09 12:2012/DAmd — Part 12: ISO base media Part 1: Panax ginseng CA Meyer 2 file format — Amendment 2: TC 261 Additive manufacturing Carriage of timed text and other * Additive manufacturing — Rapid ISO/DIS visual overlay 17296-3 technologies (rapid prototyping) 2013-07-05 — Part 3: Test methods ISO/IEC * Information technology — Cod - 14496- ing of audio-visual objects — 2013-07-13 * Additive manufacturing — Rapid ISO/DIS 16:2011/DAmd Part 16: Animation Framework technologies (rapid prototyping) 17296-4 2013-07-05 2 eXtension (AFX) — Amendment — Part 4: Data processing 2: Multi-resolution 3D mesh IULTCS International Union of compression

Leather Technologists and ISO/IEC * Information technology — Cod - Chemists Societies 14496- ing of audio-visual objects — Part 2013-07-09 26: Audio conformance — ISO/DIS 15701 * Leather - Tests for colour fast - 26:2010/DAmd Amendment 3: Conformance for ness - Part IUF 442 rev: Colour 2013-09-26 3 Low Delay AAC v2 profile fastness to migration into poly - meric material ISO/IEC DIS * Information technology — Cod - (Revision of ISO 15701:1998) 14496-30 ing of audio-visual objects 2013-07-24 — Part 30: Timed Text and JTC 1 Information technology other visual overlays in ISO Base ISO/IEC DIS * Information technology Media File Format 2382 — Vocabulary 2013-07-16

ISO Upd ate, Supplement to ISO Focus -- May 2013 7 ISO/IEC * Information technology — JPEG ISO/FDIS * Garden equipment — Safety 15444- 2000 image coding system — 2013-07-09 5395-2 requirements for 2013-06-19 12:2012/DAmd Part 12: ISO base media file for- combustion-engine-powered 2 mat — Amendment 2: Carriage of lawnmowers — Part 2: Pedestri - timed text and other visual an-controlled lawnmowers overlays (Revision of ISO 5395:1990, ISO 5395:1990/Amd 1:1992) ISO/IEC DIS * Information technology — Topic 13250-3 Maps — Part 3: XML syntax 2013-07-06 ISO/FDIS * Garden equipment — Safety 5395-3 requirements for 2013-06-19 (Revision of ISO/IEC combustion-engine-powered 13250-3:2007) lawnmowers — Part 3: Ride- on lawnmowers with seated operator (Revision of ISO 5395:1990, ISO 5395:1990/Amd 1:1992) TC 24 Particle characterization including sieving FDIS circulated ISO/FDIS * Particle characterization of par- 26824 ticulate systems — Vocabulary 2013-06-13

Period from 01 April to 30 April 2013 TC 27 Solid mineral fuels These Final draft International Standards have been submitted to the ISO/FDIS * Coal — Ultimate analysis ISO member bodies for formal approval by the date shown 17247 2013-06-06

* Available in English only (Revision of ISO 17247:2005,

ISO 17247:2005/Cor 1:2006) TC 28 Petroleum products and Vote lubricants terminates ISO/FDIS 9038 * Determination of sustained com - bustibility of liquids 2013-06-12 TC 4 Rolling bearings ISO/FDIS * Rolling bearings — Single-row (Revision of ISO 9038:2002) 12044 angular contact ball bearings — 2013-06-03 ISO/FDIS 9162 * Petroleum products — Fuels Chamfer dimensions for outer (class F) — Liquefied petroleum 2013-06-06 ring non-thrust side gases — Specifications (Revision of ISO 12044:1995) (Revision of ISO 9162:1989) TC 6 Paper, board and pulps TC 29 Small tools ISO/FDIS * Paper, board and pulps — Deter- ISO/FDIS 883 * Indexable hardmetal (carbide) in - 10775 mination of cadmium content — 2013-06-23 serts with rounded corners, with - 2013-06-09 Atomic absorption spectrometric out fixing hole — Dimensions method (Revision of ISO 883:1985) (Revision of ISO 10775:1995) ISO/FDIS * End mills with indexable inserts TC 17 Steel 6262-1 — Part 1: End mills with flatted 2013-06-09 parallel shank ISO/FDIS 4967 * Steel — Determination of con - (Revision of ISO 6262-1:1982) tent of nonmetallic inclusions 2013 -06 -05

— Micrographic method using ISO/FDIS * End mills with indexable inserts

standard diagrams 6262-2 — Part 2: End mills with Morse 2013-06-09 taper shank (Revision of ISO 4967:1998) (Revision of ISO 6262-2:1982) TC 20 Aircraft and space vehicles Side and face milling (slotting) ISO/FDIS * Air cargo — Fire containment ISO/FDIS 698 6 * cutters with indexable inserts 2013-06-09 14186 covers — Design, performance 2013-06-18 — Dimensions and testing requirements (Revision of ISO 6986:1983) TC 21 Equipment for fire protec - ISO/FDIS * Hardmetal burrs — Part 1: Gen - tion and fire fighting 7755-1 eral specifications 2013-06-23 ISO/FDIS * Fire detection and alarm systems 7240-14 — Part 14: Design, installation, 2013-06-23 (Revision of ISO 7755-1:1984) commissioning and service of fire ISO/FDIS * Hardmetal burrs — Part 2: Cylin - detection and fire alarm sys - 7755-2 drical burrs (style A) 2013-06-23 tems in and around buildings (Revision of ISO/TR (Revision of ISO 7755-2:1984) 7240-14:2003) ISO/FDIS * Hardmetal burrs — Part 3: Cy - TC 23 Tractors and machinery for 7755-3 lindrical round- (ball-) nose burrs 2013-06-23 agriculture and forestry (style C) ISO/FDIS * Garden equipment — Safety (Revision of ISO 7755-3:1984) 5395-1 requirements for combustion- 2013-06-19 ISO/FDIS * Hardmetal burrs — Part 4: engine-powered lawnmowers — 7755-4 Spherical burrs (style D) 2013-06-23 Part 1: Terminology and common tests (Revision of ISO 7755-4:1984) (Revision of ISO 5395:1990, ISO 5395:1990/Amd 1:1992)

8 ISO Upd ate, Supplement to ISO Focus -- May 2013

ISO/FDIS * Hardmetal burrs — Part 5: Oval TC 42 Photography 7755-5 burrs (style E) 2013-06-23 ISO/FDIS * Photography — Electronic still 15740 picture imaging — Picture trans - 2013-06-23 (Revision of ISO 7755-5:1984) fer protocol (PTP) for digital still ISO/FDIS * Hardmetal burrs — Part 6: Arch photography devices 7755-6 round- (ball-) nose burrs (style F) 2013-06-23 (Revision of ISO 15740:2008)

(Revision of ISO 7755-6:1984) TC 43 Acoustics ISO/FDIS 1680 Acoustics — Test code for the ISO/FDIS * Ha rdmetal burrs — Part 7: Arch * 7755-7 pointed-nose burrs (style G) 2013-06-23 measurement of airborne noise 2013-07-12 emitted by rotating electrical (Revision of ISO 7755-7:1984) machines (Revision of ISO 1680:1999, ISO ISO/FDIS * Hardmetal burrs — Part 8: Flame 1680:1999/DAmd 1) 7755-8 burrs (style H) 2013-06-23 TC 45 Rubber and rubber (Revision of ISO 7755-8:1984) products ISO/FDIS * Hardmetal burrs — Part 9: 60 ISO/FDIS 5999 * Flexible cellular polymeric 7755-9 degrees and 90 degrees cone 2013-06-23 materials — Polyurethane foam 2013-06-26 burrs (styles J and K) for load-bearing applications (Revision of ISO 7755-9:1984) excluding carpet underlay — Specification ISO/FDIS * Hardmetal burrs — Part 10: (Revision of ISO 5999:2007) 7755-10 Conical round- (ball-) nose burrs 2013-06-23 (style L) TC 46 Information and (Revision of ISO 7755-10:1984) documentation ISO/FDIS * Hardmetal burrs — Part 11: ISO/FDIS Codes for the representation 7755-11 Conical pointed-nose burrs (style 2013-06-23 3166-1 of names of countries and their 2013-06-20 M) subdivisions — Part 1: Country (Revision of ISO 7755-11:1984) codes (Revision of ISO 3166-1:2006, ISO/FDIS * Hardmetal burrs — Part 12: 7755-12 Inverted cone burrs (style N) 2013-06-23 ISO 3166-1:2006/Cor 1:2007) ISO/FDIS Codes for the representation (Revision of ISO 7755-12:1984) 3166-2 of names of countries and their 2013-06-20 subdivisions — Part 2: Country TC 34 Food products subdivision code ISO 9167- * Rapeseed — Determination of (Revision of ISO 3166-2:2007) 1:1992/FDAmd 2013-06-05 glucosinolates content — Part 1: ISO/FDIS Codes for the representation 1 Method using high-performance 3166-3 of names of countries and their 2013-06-20 liquid chromatography — subdivisions — Part 3: Code Amendment 1 for formerly used names of ISO/FDIS 5527 * Cereals — Vocabulary countries 2013-07-03 (Revision of ISO 3166-3:1999) TC 54 Essential oils (Revision of ISO 5527:1995) ISO/FDIS 4716 * Essential oil of vetiver [Chrys - ISO/FDIS * Microbiology of food and animal opogon zizanioides (L.) Roberty, 2013-06-26 4833-1 feed — Horizontal method for the 2013-06-26 syn. Vetiveria zizanioides (L.) enumeration of microorgan - isms Nash] — Part 1: Colony count at 30 degrees C by the pour plate (Revision of ISO 4716:2002) technique TC 61 Plastics

(Revision of ISO 4833:2003) ISO/FDIS * Plastics — Methods of exposure ISO/FDIS * Microbiology of f ood and animal 4892-4 to laboratory light sources — 2013-06-11 4833-2 feed — Horizont al method for 2013-06-26 Part 4: Open-flame carbon-arc the enumeration of microorgan - lamps isms — Part 2: Colony count (Revision of ISO 4892-4:2004, at 30 degrees C by the surface ISO 4892-4:2004/Cor 1:2005) plating technique TC 67 Materials, equipment and ISO/FDIS 3657 * Animal and vegetable fats and offshore structures for pe - oils — Determination of saponifi - 2013-06-05 troleum, petrochemical and cation value (Revision of ISO 3657:2002) natural gas industries ISO * Petroleum and natural gas ISO/FDIS 3961 * Animal and vegetable fats and 19902:2007/ industries — Fixed steel offshore 2013-06-12 oils — Determination of iodine 2013-06-05 FDAmd 1 structures — Amendment 1 value (Revision of ISO 3961:2009) TC 70 Internal combustion TC 38 Textiles engines ISO/FDIS * Textiles — Quantitative chemical ISO/FDIS * Methods of test for full-flow 1833-25 analysis — Part 25: Mixtures of 2013-06-26 4548-5 lubricating oil filters for internal 2013-06-06 polyester and certain other fibres combustion engines — Part 5: (method using trichloracetic acid Test for cold start simulation and and chloroform) hydraulic pulse durability (Revision of ISO 4548-5:1990) ISO/FDIS * Woven fabrics — Distortion — 13015 Determination of skew and bow 2013-06-19

ISO Upd ate, Supplement to ISO Focus -- May 2013 9

TC 85 Nuclear energy, nuclear ISO/FDIS * Soil quality — Determination of technologies, and radio - 11916-1 selected explosives and related 2013-06-30 logical protection compounds — Part 1: Method using high-performance liquid ISO/FDIS * Measurement of radioactivity in chromatography (HPLC) with 18589-7 the environment — Soil — Part 2013-06-26 ultraviolet detection 7: In situ measurement of gamma-emitting radionuclides ISO/FDIS * Soil quality — Determination of 11916-2 selected explosives and related 2013-06-30 TC 104 Freight containers compounds — Part 2: Method ISO/FDIS 668 * Series 1 freight containers — using gas chromatography (GC) Classification, dimensions and 2013-06-16 with electron capture detection ratings (ECD) or mass spectrometric detection (MS) (Revision of ISO 668:1995, ISO 668:1995/Amd 1:2005, ISO TC 199 Safety of machinery 668:1995/Amd 2:2005) ISO/FDIS * Safety of machinery — Pressure- TC 106 Dentistry 13856-3 sensitive protective devices 2013-06-05 ISO/FDIS * Dentistry — Minimal dental im - — Part 3: General principles for 16498 plant data set for clinical use 2013-06-12 design and testing of pressure- sensitive bumpers, plates, wires and similar devices TC 120 Leather (Revision of ISO 13856-3:2006) ISO/FDIS 5431 * Leather — Wet blue goat skins TC 207 Environmental — Specification 2013-06-18 management (Revision of ISO 5431:1999) ISO/FDIS * Environmental management 14031 — Environmental performance 2013-06-19 ISO/FDIS 5432 * Leather — Wet blue sheep skins evaluation — Guidelines — Specification 2013-06-18 (Revision of ISO 14031:1999) (Revision of ISO 5432:1999) TC 213 Dimensional and geometri - ISO/FDIS 5433 * Leather — Bovine wet blue cal product specifications — Specification 2013-06-18 and verification ISO/FDIS * Geometrical product specifica - (Revision of ISO 5433:1999) 14253-1 tions (GPS) — Inspection by 2013-06-12 TC 122 Packaging measurement of workpieces and measuring equipment — Part ISO/FDIS * Packaging — Transport packag - 1: Decision rules for proving 13274 ing for dangerous goods — 2013-06-26 conformity or nonconformity with Plastics compatibility testing for specifications packaging and IBCs (Revision of ISO 14253-1:1998, ISO/FDIS * Packaging — Transport packag - ISO 14253-1:1998/DAmd 1) ing for dangerous goods — Test 16495 2013-06-12 ISO/FDIS * Geometrical product specifica - 25178-603 tions (GPS) — Surface texture: 2013-06-12 methods Areal — Part 603: Nominal characteristics of non-contact TC 153 Valves ISO/FDIS * Metallic butterfly valves for gen - (phase-shifting interferometric 10631 eral purposes 2013-06-09 microscopy) instruments

(Revision of ISO 10631:1994) TC 216 Footwear TC 163 Thermal performance and ISO/FDIS * Footwear and footwear compo - energy use in the built 16187 nents — Test method to assess 2013-06-12 antibacterial activity environment ISO/FDIS * Hygrothermal performance of CASCO Committee on conformity 12571 building materials and products 2013 -06 -12 assessment

— Determination of hygroscopic ISO/IEC FDIS * Conformity assessment — Fun -

sorption properties 17067 damentals of product certifica - 2013-06-12 (Revision of ISO 12571:2000) tion and guidelines for product certification schemes TC 172 Optics and photonics (Revision of ISO/IEC ISO 10110- * Optics and photonics — Prepa - Guide 12:2007/ ration of drawings for optical 2013-06-30 67:2004) FDAmd 1 elements and systems — Part JTC 1 Information technology 12: Aspheric surfaces — Amend - ISO/IEC/IEEE * Software and systems engineer- ment 1 FDIS 29119-1 2013-06-23 ing — Software testing — Part 1: TC 173 Assistive products for per- Concepts and definitions sons with disability ISO/IEC/IEEE * Software and systems engineer- FDIS 29119-2 2013-06-23 ISO/FDIS * Wheelchairs — Part 25: Batteries ing — Software testing — Part 2: 7176-25 and chargers for powered wheel - 2013-06-03 Test process ISO/IEC/IEEE * chairs — Requirements and test Software and systems engineer- FDIS 29119-3 2013-06-23 methods ing — Software testing — Part 3: TC 190 Soil quality Test documentation

10 ISO Upd ate, Supplement to ISO Focus -- May 2013

ISO/IEC * Information technology — Cod - ISO * Tractors for agriculture and forestry 14496- ing of audio-visual objects 2013-06-13 27850:2013 — Falling object protective structures J 10:2012/ — Part 10: Advanced Video — Test procedures and performance FDAmd 1 Coding — Amendment 1: Addi - requirements tional profiles and supplemental ISO Agricultural machinery — Safety — enhancement information (SEI) 4254-1:2013 Part 1: General requirements messages R ISO/IEC FDIS * Information technology — MPEG ISO Self-propelled agricultural machinery 23002-5 video technologies — Part 5: 2013-06-13 16231-1:2013 — Assessment of stability — Part 1: B Reconfigurable media coding Principles conformance and reference software TC 28 Petroleum products and lubricants ISO Petroleum products — Calculation 4264:2007/ of cetane index of middle-distillate XZ Amd 1:2013 fuels by the four-variable equation — Amendment 1 ISO Petroleum and related products — De - 4404-2:2010 termination of the corrosion resistance D of fire-resistant hydraulic fluids — Part Standards published 2: Non-aqueous fluids ISO Determination of flash point — Abel 13736:2013 closed-cup method L New International Standards published between 01 April and 30 April 2013 TC 29 Small tools * Available in English only ISO 6106:2013 Abrasive products — Checking the ** French version of standard previously published in English only grain size of superabrasives E

ISO 9284:2013 Abrasive grains — Test-sieving Price machines B group ISO Milling cutters — Designation — TC 2 Fasteners 11529:2013 Shank-type and bore-type milling G cutters of solid or tipped design or with ISO 898- Mechanical properties of fasteners indexable cutting edges 1:2013/Cor 1 made of carbon steel and alloy steel free — Part 1: Bolts, screws and studs with TC 34 Food products specified property classes — Coarse ISO Wheat flour — Physical characteristics thread and fine pitch thread — Techni - 5530-1:2013 of doughs — Part 1: Determination M cal Corrigendum 1 of water absorption and rheological TC 4 Rolling bearings properties using a farinograph ISO Rolling bearings — Accessories — Part ISO/TS Microbiology of food and animal feed 2982-1:2013 1: Dimensions for adapter sleeve as - D 15216-1:2013 — Horizontal method for determination P semblies and withdrawal sleeves of hepatitis A virus and norovirus in food using real-time RT-PCR — Part 1: ISO Rolling bearings — Accessories — Part Method for quantification 2982-2:2013 2: Dimensions for locknuts and locking F devices ISO/TS Microbiology of food and animal feed 15216-2:2013 — Horizontal method for determination N TC 6 Paper, board and pulps of hepatitis A virus and norovirus in ISO/TS * Paper and board — Determination of food using real-time RT-PCR — Part 2: 17958:2013 fracture toughness — Constant rate of H Method for qualitative detection elongation method (1,7 mm/s) ISO Animal feeding stuffs — Determination TC 8 Ships and marine technology 17180:2013 of lysine, methionine and threonine in F commercial amino acid products and ISO * Ships and marine technology — Marine premixtures 16165:2013 environment protection — Terminology Q relating to oil spill response ISO Foodstuffs — Methods of analysis for 21569:2005/ the detection of genetically modified X TC 22 Road vehicles Amd 1:2013 organisms and derived products — ISO * Road vehicles — Vehicle to grid com - Qualitative nucleic acid based methods 15118-1:2013 munication interface — Part 1: General V — Amendment 1 information and use-case definition ISO Foodstuffs — Methods of analysis for ISO * Road vehicles — Pedestrian protection 21570:2005/ the detection of genetically modi- XZ 16850:2007/ — Child head impact test method — XZ Amd 1:2013 fied organisms and derived products Amd 1:2013 Amendment 1 — Quantitative nucleic acid based methods — Amendment 1 ISO * Motorcycles — Measurement methods 17479:2013 for gaseous exhaust emissions during E ISO Foodstuffs — Methods of analysis for inspection or maintenance 24276:2006/ the detection of genetically modified XZ Amd 1:2013 organisms and derived products — TC 23 Tractors and machinery for agri - General requirements and definitions culture and forestry — Amendment 1 TC 38 Textiles

ISO Upd ate, Supplement to ISO Focus -- May 2013 11 ISO Textiles — Tensile properties of fabrics TC 67 Materials, equipment and off- 13934-1:2013 — Part 1: Determination of maximum F shore structures for petroleum, force and elongation at maximum force petrochemical and natural gas using the strip method industries TC 41 Pulleys and belts (including ISO Petroleum and natural gas industries veebelts) 15546:2011 — Aluminium alloy drill pipe S ISO Steel cord conveyor belts — Longitu - 7622-1:2013 dinal traction test — Part 1: Measure- B ISO Petroleum and natural gas indus - ment of elongation 20312:2011 tries — Design and operating limits U ISO 8094:2013 Steel cord conveyor belts — Adhesion of drill strings with aluminium alloy strength test of the cover to the core B components layer ISO Petroleum and natural gas industries TC 42 Photography 19901-7:2013 — Specific requirements for offshore XC structures — Part 7: Stationkeeping ISO * Photography and graphic technol - systems for floating offshore structures 22028-2:2013 ogy — Extended colour encodings for K and mobile offshore units digital image storage, manipulation and interchange — Part 2: Reference out - TC 69 Applications of statistical put medium metric RGB colour image methods encoding (ROMM RGB) ISO * Statistics — Vocabulary and symbols TC 43 Acoustics 3534-3:2013 — Part 3: Design of experiments X ISO * Acoustics — Measurement of sound 5129:2001/ pressure levels in the interior of aircraft XZ TC 71 Concrete, reinforced concrete Amd 1:2013 during flight — Amendment 1 and pre-stressed concrete TC 44 Welding and allied processes ISO * Performance guidelines for design of ISO Gas welding equipment — Acetylene 14484:2013 concrete structures using fibre-rein - C 15615:2013 manifold systems for welding, cutting H forced polymer (FRP) materials and allied processes — Safety require- TC 86 Refrigeration and ments in high-pressure devices air-conditioning ISO Soft soldering fluxes — Test methods ISO * Air-cooled air conditioners and air-to- 9455-16:2013 — Part 16: Flux efficacy test, wetting J 16358-1:2013 air heat pumps — Testing and calculat - M balance method ing methods for seasonal performance TC 54 Essential oils factors — Part 1: Cooling seasonal performance factor ISO * Essential oil of rose, Chinese Kushui 25157:2013 type (Rosa sertata x Rosa rugosa) D ISO * Air-cooled air conditioners and air-to- 16358-2:2013 air heat pumps — Testing and calculat - R ing methods for seasonal performance TC 58 Gas cylinders factors — Part 2: Heating seasonal ISO * Gas cylinders — Refillable composite performance factor 11119-3:2013 gas cylinders and tubes — Design, R ISO * Air-cooled air conditioners and air-to- construction and testing — Part 3: 16358-3:2013 air heat pumps — Testing and calculat - C Fully wrapped fibre reinforced com - ing methods for seasonal performance posite gas cylinders and tubes up to factors — Part 3: Annual performance 450L with non-load-sharing metallic or factor non-metallic liners TC 92 Fire safety TC 61 Plastics ISO Methods for sampling and analysis of ISO 75-1:2013 Plastics — Determination of tempera - 19701:2013 fire effluents XA ture of deflection under load — Part 1: E General test method TC 94 Personal safety -- Protective ISO 75-2:2013 Plastics — Determination of tempera - clothing and equipment ture of deflection under load — Part 2: D Plastics and ebonite ISO/TS * Respiratory protective devices — Hu - 16976-7:2013 man factors — Part 7: Hearing and F ISO 178:2010/ Plastics — Determination of flexural speech Amd 1:2013 properties — Amendment 1 XZ TC 106 Dentistry ISO 180:2000/ Plastics — Determination of Izod ISO Dentistry — Endodontic instruments — Amd 2:2013 impact strength — Amendment 2: XZ 3630-2:2013 Part 2: Enlargers H Precision data ISO Plastics — Differential scanning calo - TC 110 Industrial trucks 11357-2:2013 rimetry (DSC) — Part 2: Determination C ISO 22915- Industrial trucks — Verification of sta - of glass transition temperature and 4:2009/Amd bility — Part 4: Pallet stackers, double XZ glass transition step height 1:2013 stackers and order-picking trucks with ISO Plastics — Determination of the degree operator position elevating up to and 16929:2013 of disintegration of plastic materials E including 1 200 mm lift height — under defined composting conditions Amendment 1 in a pilot-scale test TC 111 Round steel link chains, chain ISO * Adhesives — Adhesives for bonding slings, components and 17178:2013 parquet to subfloor — Test methods E accessories and minimum requirements ISO 7597:2013 * Forged steel lifting hooks with latch, grade 8 E

12 ISO Upd ate, Supplement to ISO Focus -- May 2013 TC 112 Vacuum technology ISO * Corrosion of metals and alloys — 7539-11:2013 Stress corrosion cracking — Part 11: H ISO 2861:2013 * Vacuum technology — Dimensions of Guidelines for testing the resistance of clamped-type quick-release couplings C metals and alloys to hydrogen embrittlement and hydrogen-assisted TC 121 Anaesthetic and respiratory cracking equipment TC 159 Ergonomics ISO * Non-invasive sphygmomanometers ISO/TR 7250- * Basic human body measurements for 81060-2:2013 — Part 2: Clinical investigation of S 2:2010/Amd technological design — Part 2: Statisti - XZ 1:2013 cal summaries of body measurements automated measurement type from national populations — Amend - TC 126 Tobacco and tobacco products ment 1 ISO 2971:2013 Cigarettes and filter rods — Determina - tion of nominal diameter — Method J TC 163 Thermal performance and en - using a non-contact optical measuring ergy use in the built environment apparatus ISO * Thermal insulating products for build - TC 127 Earth-moving machinery 18098:2013 ing equipment and industrial installa - B tions — Determination of the apparent ISO 7130:2013 * Earth-moving machinery — Operator density of preformed pipe insulation training — Content and methods B ISO * Thermal insulating products for build - 18099:2013 ing equipment and industrial installa - D ISO 7133:2013 Earth-moving machinery — Scrap - tions — Determination of the coeffi - ers — Terminology and commercial K specifications cient of thermal expansion TC 130 Graphic technology TC 165 Timber structures ISO/TR * Timber structures — Bond perfor- ISO * Graphic technology — Management of 20152-3:2013 mance of adhesives — Part 3: Use of B 14298:2013 security printing processes K alternative species for bond tests

TC 131 Fluid power systems TC 176 Quality management and quality assurance ISO/TS Hydraulic fluid power — Hose assem - 17165-2:2013 blies — Part 2: Practices for hydraulic J ISO Quality management — Customer hose assemblies 10004:2012 satisfaction — Guidelines for monitor- P ing and measuring ISO 6263:2013 Hydraulic fluid power — Compen - sated flow-control valves — Mounting K TC 184 Automation systems and surfaces integration TC 142 Cleaning equipment for air and ISO 9787:2013 Robots and robotic devices — other gases Coordinate systems and motion F nomenclatures ISO Air intake filter systems for rotary 29461-1:2013 machinery — Test methods — Part 1: V ISO * Automation systems and integration — Evaluating Static filter elements 20140-1:2013 energy efficiency and other S factors of manufacturing systems that TC 146 Air quality influence the environment — Part 1: ISO Interior air of road vehicles — Part 4: Overview and general principles 12219-4:2013 Method for the determination of the H TC 198 Sterilization of health care emissions of volatile organic com - products pounds from vehicle interior parts and materials — Small chamber method ISO 13408- Aseptic processing of health care 1:2008/Amd products — Part 1: General require- XZ TC 147 Water quality 1:2013 ments — Amendment 1 ISO Water quality — Radium-226 — Part ISO/TS * Sterilization of health care products 1: Test method using liquid scintillation 13165-1:2013 G 17665-3:2013 — Moist heat — Part 3: Guidance on U counting the designation of a medical device ISO * Water quality — Determination of the to a product family and processing 16191:2013 toxic effect of sediment on the growth L category for steam sterilization behaviour of Myriophyllum aquaticum TC 199 Safety of machinery ISO Water quality — Biochemical and ISO Safety of machinery — Pressure- 23893-3:2013 physiological measurements on fish — L 13856-1:2013 sensitive protective devices — Part T Part 3: Determination of vitellogenin 1: General principles for design and TC 150 Implants for surgery testing of pressure-sensitive mats and pressure-sensitive floors ISO * Implants for surgery — Cardiac pace - 5841-3:2013 makers — Part 3: Low-profile connec - F ISO Safety of machinery — Pressure- tors (IS-1) for implantable pacemakers 13856-2:2013 sensitive protective devices — Part U 2: General principles for design and TC 153 Valves testing of pressure-sensitive edges and ISO Industrial valves — Isolating valves for pressure-sensitive bars 28921-1:2013 low-temperature applications — Part 1: L TC 202 Microbeam analysis Design, manufacturing and production testing ISO Microbeam analysis — Electron probe 23833:2013 microanalysis (EPMA) — Vocabulary N TC 156 Corrosion of metals and alloys

TC 204 Intelligent transport systems

ISO Upd ate, Supplement to ISO Focus -- May 2013 13 ISO Electronic fee collection — Application IULTCS International Union of Leather 14906:2011/ interface definition for dedicated short- free Technologists and Chemists Cor 1:2013 range communication — Technical Societies Corrigendum 1 ISO Leather - Physical and mechanical ISO/TR * Public transport — Interoperable fare 17130:2013 tests - Determination of dimensional B 24014-3:2013 management system — Part 3: R change Complementary concepts to Part 1 for multi-application media CASCO Committee on conformity assessment ISO * Intelligent transport systems — Com - 29281-1:2013 munication access for land mobiles P ISO/IEC Conformity assessment — Require- (CALM) — Non-IP networking — Part 17020:2012 ments for the operation of various J 1: Fast networking & transport layer types of bodies performing inspection protocol (FNTP) JTC 1 Information technology ISO * Intelligent transport systems — Com - ISO/IEC * Information technology — Univer- 29281-2:2013 munication access for land mobiles M 10646:2012/ sal Coded Character Set (UCS) — XB (CALM) — Non-IP networking — Part Amd 1:2013 Amendment 1: Linear A, Palmyrene, 2: Legacy system support Manichaean, TC 206 Fine ceramics Khojki, Khudawadi, Bassa Vah, Du - ployan, and other ISO Fine ceramics (advanced ceramics, characters 22197-4:2013 advanced technical ceramics) — Test E method for air-purification perfor- ISO/IEC TR * Information technology — Future mance of semiconducting photocata - 29181-3:2013 Network — Problem statement and N lytic materials — Part 4: Removal of requirements — Part 3: Switching and formaldehyde routing ISO Fine ceramics (advanced ceramics, ISO/IEC TR * Information technology — Future 22197-5:2013 advanced technical ceramics) — Test E 29181-6:2013 Network — Problem statement and re- P method for air-purification performance of quirements — Part 6: Media transport semiconducting photocatalytic materials * Information technology — Future — Part 5: Removal of methyl mercaptan ISO/IEC TR 29181-7:2013 Network — Problem statement and T requirements — Part 7: Service TC 207 Environmental management composition ISO/TR * Greenhouse gases — Quantification ISO/IEC * Identification cards — Integrated circuit 14069:2013 and reporting of greenhouse gas emis - X 7816-4:2013 cards — Part 4: Organization, security XB sions for organizations — Guidance for and commands for interchange the application of ISO 14064-1 ISO * Information processing — Volume and TC 211 Geographic information/ 9660:1988/ file structure of CD-ROM for informa - XZ Geomatics Amd 1:2013 tion interchange — Amendment 1 ISO Geographic information — Land Ad - ISO/IEC * Information technology — Security 19152:2012 ministration Domain Model (LADM) XA 27014:2013 techniques — Governance of informa - F tion security

TC 213 Dimensional and geometrical ISO/IEC * Information technology — Digital com - 10918-5:2013 pression and coding of continuous- E product specifications and tone still images: JPEG File Inter- verification change Format (JFIF) — Part 5: ISO/TS Geometrical product specification ISO/IEC * Information technology — Digital 17863:2013 (GPS) — Geometrical tolerancing of J 10918-6:2013 compression and coding of continu - C moveable assemblies ous-tone still images: Application to TC 217 Cosmetics printing systems — Part 6: ISO Cosmetics — Microbiology — Evalua - ISO/IEC * Information technology — JPEG 11930:2012 tion of the antimicrobial protection of a L 15444-1:2004/ 2000 image coding system: Core XZ cosmetic product Amd 4:2013 coding system — Part 1: — Amend - ment 4: Guidelines for digital cinema ISO/TR Cosmetics — Analytical methods — applications 14735:2013 Nitrosamines: Technical guidance E document for minimizing and determin - ISO/IEC * Information technology — JPEG 2000 ing N-nitrosamines in cosmetics 15444-1:2004/ image coding system: Core coding XZ Amd 5:2013 system — Part 1: — Amendment 5: TC 227 Springs Enhancements for digital cinema and ISO * Springs — Symbols archive profiles (additional frame rates) 16249:2013 L ISO/IEC * Information technology — Multimedia 23000- application format (MPEG-A) — Part XZ TC 240 Project Committee: Product 12:2010/Amd 12: Interactive music application recall 3:2013 format — Amendment 3: Conformance and reference software ISO * Consumer product recall — Guidelines 10393:2013 for suppliers R ISO/IEC * Information technology — Media 23005-2:2013 context and control — Part 2: Control XC information TC 243 Project Committee: Consumer * Information technology — Media product safety ISO/IEC 23005-3:2013 context and control — Part 3: Sensory XA ISO * Consumer product safety — Guidelines information 10377:2013 for suppliers T ISO/IEC * Information technology — Media con - 23005-4:2013 text and control — Part 4: Virtual world XC object characteristics

14 ISO Upd ate, Supplement to ISO Focus -- May 2013 ISO/IEC * Information technology — Multimedia ISO 7957:1987 (reconfirmed) service platform technologies — Part 23006-1:2013 K ISO 7958:1987 (reconfirmed) 1: Architecture ISO 7959:1987 (reconfirmed) ISO 7983:1988 (reconfirmed) ISO 7984:1988 (reconfirmed) ISO 7987:1985 (reconfirmed) ISO 7988:1988 (reconfirmed) Standards confirmed ISO 9264:1988 (reconfirmed) ISO 9265:1988 (reconfirmed) ISO 9266:1988 (reconfirmed) The following International Standards are confimred for a five year ISO 9267:1988 (reconfirmed) period: ISO 9375:1989 (reconfirmed) ISO 9414:1989 (reconfirmed) TC 6 Paper, board and pulps ISO 9415:1989 (reconfirmed) ISO 302:2004 (reconfirmed) ISO 9451:1989 (reconfirmed) TC 22 Road vehicles ISO 9452:1989 (reconfirmed) ISO 2958:1973 (reconfirmed) ISO 9535:1989 (reconfirmed) ISO 3208:1974 (reconfirmed) ISO 9536:1989 (reconfirmed) ISO 3795:1989 (reconfirmed) ISO 9537:1989 (reconfirmed) ISO 5422:1982 (reconfirmed) ISO 9558:1989 (reconfirmed) ISO 10599-2:1997 (reconfirmed) ISO 9566:1989 (reconfirmed) ISO 15763:2002 (reconfirmed) ISO 9567:1989 (reconfirmed) TC 29 Small tools ISO 9615:1989 (reconfirmed) ISO 2421:2003 (reconfirmed) ISO 9616:1989 (reconfirmed) ISO 9136-1:2004 (reconfirmed) ISO 9617:1989 (reconfirmed) ISO 9285:1997 (reconfirmed) TC 48 Laboratory equipment ISO 9286:1997 (reconfirmed) ISO 7550:1985 (reconfirmed) ISO 15637-1:2002 (reconfirmed) ISO 7713:1985 (reconfirmed) ISO 15637-2:2002 (reconfirmed) ISO 8655-1:2002 (reconfirmed) ISO 21537-1:2004 (reconfirmed) ISO 8655-2:2002 (reconfirmed) ISO 21537-2:2004 (reconfirmed) ISO 8655-3:2002 (reconfirmed) TC 34 Food products ISO 8655-4:2002 (reconfirmed) ISO 6655:1997 ISO 8655-5:2002 (reconfirmed) TC 38 Textiles ISO 4795:1996 (reconfirmed) ISO 105-C12:2004 (reconfirmed) TC 61 Plastics ISO 105-J01:1997 (reconfirmed) ISO 23560:2008 ISO 105-J02:1997 (reconfirmed) TC 72 Textile machinery and accessories ISO 105-P02:2002 (reconfirmed) ISO 8115-3:1995 (reconfirmed) ISO 105-Z03:1996 (reconfirmed) TC 81 Common names for pesticides and ISO 105-Z05:1996 (reconfirmed) other agrochemicals ISO 105-Z10:1997 (reconfirmed) ISO 1750:1981 (reconfirmed) TC 39 Machine tools TC 85 Nuclear energy, nuclear technologies, ISO 7006:1981 (reconfirmed) and radiological protection ISO 7007:1983 (reconfirmed) ISO 21243:2008 ISO 7008:1983 (reconfirmed) TC 91 Surface active agents ISO 7009:1983 (reconfirmed) ISO 304:1985 (reconfirmed) ISO 7568:1986 (reconfirmed) ISO 696:1975 (reconfirmed) ISO 7569:1986 (reconfirmed) ISO/TR 896:1977 (reconfirmed) ISO 7570:1986 (reconfirmed) ISO 4316:1977 (reconfirmed) ISO 7571:1986 (reconfirmed) ISO 4318:1989 (reconfirmed) ISO 7945:1985 (reconfirmed) ISO 4319:1977 (reconfirmed) ISO 7946:1985 (reconfirmed) ISO 4320:1977 (reconfirmed) ISO 7947:1985 (reconfirmed) ISO 4322:1977 (reconfirmed) ISO 7948:1987 (reconfirmed) ISO 4324:1977 (reconfirmed) ISO 7949:1985 (reconfirmed) ISO 4326:1980 (reconfirmed) ISO 7950:1985 (reconfirmed) ISO 4327:1979 (reconfirmed)

ISO Upd ate, Supplement to ISO Focus -- May 2013 15 ISO 6121:1988 (reconfirmed) ISO 3272-3:2001 (reconfirmed) ISO 6122:1978 (reconfirmed) ISO 6148:2001 (reconfirmed) ISO 6384:1981 (reconfirmed) ISO 8127-1:1989 (reconfirmed) ISO 6387:1983 (reconfirmed) ISO 9923:1994 (reconfirmed) ISO 6388:1989 (reconfirmed) ISO 12656:2001 (reconfirmed) ISO 6835:1981 (reconfirmed) ISO 32000-1:2008 ISO 6836:1983 (reconfirmed) ISO 6196-3:1997 (reconfirmed) ISO 6837:1982 (reconfirmed) ISO 6196-5:1987 (reconfirmed) ISO 6839:1982 (reconfirmed) ISO 6196-6:1992 (reconfirmed) ISO 6840:1982 (reconfirmed) ISO 6196-7:1992 (reconfirmed) ISO 6842:1989 (reconfirmed) ISO/TR (reconfirmed) 12036:2000 ISO 6843:1988 (reconfirmed) ISO/TR (reconfirmed) ISO 6844:1983 (reconfirmed) 12037:1998 ISO 6845:1989 (reconfirmed) ISO/TR ISO 6889:1986 (reconfirmed) 12654:1997 ISO 7535:1984 (reconfirmed) ISO/TR ISO 8212:1986 (reconfirmed) 18492:2005 ISO 8214:1985 (reconfirmed) TC 172 Optics and photonics ISO 8215:1985 (reconfirmed) ISO 9802:1996 (reconfirmed) ISO 9101:1987 (reconfirmed) ISO 10629:1996 (reconfirmed) TC 93 Starch (including derivatives and TC 190 Soil quality by-products) ISO 10573:1995 (reconfirmed) ISO 1743:1982 (reconfirmed) ISO 11276:1995 (reconfirmed) ISO 3188:1978 (reconfirmed) ISO 11461:2001 (reconfirmed) ISO 3946:1982 (reconfirmed) TC 219 Floor coverings ISO 5378:1978 (reconfirmed) ISO 24334:2006 ISO 11212-1:1997 (reconfirmed) TC 227 Springs ISO 11212-2:1997 (reconfirmed) ISO 2162-2:1993 (reconfirmed) ISO 11212-3:1997 (reconfirmed) ISO 11212-4:1997 (reconfirmed)

ISO 11215:1998 (reconfirmed) ISO 11216:1998 (reconfirmed) TC 104 Freight containers ISO 14829:2002 (reconfirmed) Standards withdrawn ISO 10374:1991 (reconfirmed) TC 107 Metallic and other inorganic coatings Period from 01 April to 30 April 2013 ISO 3613:2010

TC 118 Compressors and pneumatic tools, machines and equipment TC 29 Small tools ISO 3857-1:1977 (reconfirmed) ISO 11529-1:2005 (replaced by ISO 11529:2013) TC 121 Anaesthetic and respiratory equipment ISO 11529-2:2005 (replaced by ISO 11529:2013) ISO 10651-4:2002 TC 34 Food products ISO/TS (replaced by ) TC 122 Packaging 21098:2005 ISO 6590-2:1986 (reconfirmed) TC 42 Photography TC 138 Plastics pipes, fittings and valves for ISO/TS (replaced by ISO 22028-2:2013) the transport of fluids 22028-2:2006 ISO 10838-2:2000 (reconfirmed) TC 112 Vacuum technology TC 147 Water quality ISO 2861-1:1974 (replaced by ISO 2861:2013) ISO 15587-1:2002 (reconfirmed) TC 131 Fluid power systems ISO 15587-2:2002 (reconfirmed) ISO/TR (replaced by ISO/TS 17165-2:2013) ISO/TS (reconfirmed) 17165-2:2006 16489:2006 TC 204 Intelligent transport systems ISO 6461-2:1986 (reconfirmed) ISO 29281:2011 (replaced by ISO 29281-1:2013, ISO ISO 18749:2004 (reconfirmed) 29281-2:2013) TC 171 Document management applications ISO 3272-2:1994 (reconfirmed)

16 ISO Upd ate, Supplement to ISO Focus -- May 2013

ISO Upd ate, Supplement to ISO Focus -- May 2013 17