Popodusche Eco 2.0

OPERATION MANUAL LIABILITY DISCLOSURE

The supplier is not liable for damages caused by negligence in the following areas:

1. This is an electronic device and must be grounded!

2. Persons with disabilities or small children should not be allowed to use this product without supervision.

3. This product is an electrical device, please pay attention to a proper installation.

SAFETY INSTRUCTIONS

1. Do not insert or remove any electrical plug with wet hands. Electrical shock may occur.

2. Do not damage the power cord and the plug. Otherwise there is a risk of electric shock, short circuit and re.

3. Do not use a damaged electrical plug, cord or a loose plug-in. Any negligence could result in electrical shock, re, short circuit or damage to your product may occur.

4. An electrical installation should be installed professionally. Any negligence could result in electric shock, short circuit, re or damage to your device.

5. Do not disassemble any device without expert knowledge. Any negligence could result in electric shock, short circuit, re or damage to your device.

6. Do not allow any uids of any kind to come in contact with the electrical components. Any negligence could result in electric shock, short circuit, re or damage to your device.

7. Caution! Please pay attention to the water ow direction. Negligence can cause irreparable damage to your device.

8. Don not bend, twist or bend the steel water hose, this could cause a leak.

2 TECHNICAL SPECIFICATIONS Wash Rear Wash Lady Wash Water temperature settings 5 Settings (Standard 3) Stream settings 5 Settings (Standard 3) Stream direction settings 5 Settings (Standard 5)

Hygiene Self-cleaning jet Manuell cleaning Nightlight settings Ambient light Intelligent energy saver Soft-Close seat Control head Rimless toilet Water connection G 3/8“ Electrical connection 240 V, 50/60 Hz Watts 950 W Length of cable 1,80 m Waterpressure 0,07 - 0,75 MPa (0,7-7,5 bar) Water temperature 4°C - 35°C Operating temperature range 4°C - 40°C Safety class IPX4

Water Settings Water 350 ~ 650 Milliliter per minute Water temperatur 31°C - 39°C Wash cycle 3 minutes Heating module Warm water boiler Maximum Heat 1200 W Safety Fuse Thermo-cut-off-fuse, Fill cut-off fuse, Back check Air gap

Net weight 32 kg Dimensions B 384 x T 593 x H 380 mm

3 TECHNICAL DRAWINGS

4 OVERVIEW

Cover

Nicht Light

Rear Wash Seat sensor Lady Wash Ambient Light

Control-Knob

Seat

Ceramic

5 FUNKTIONS

REAR WASH / LADYWASH

You can operate the Rear or Lady -Wash by pressing the „ “ or „ “ button on the control-knob.

The washing will stop after 3 minutes or you can stop the funktion by pressing the „ “ button on the control-knob.

Lady Wash Rear Wash

STOP-button

ADJUST WATER FLOW

In the process of Rear Wash or Ladywash you can operate by rotating the knob. The rate will increase in the clockwise direction and decrease in the anticlockwise direction.

less more

ADJUST THE NOZZLE POSITION pull You can adjust the nozzle position by pulling out the contol-knob and then turn it clockwise (the nozzle moves forward) or turn it anti clockwise (the nozzle moves backwards) .

moves back moves forward

more ADJUST WATER TEMPERATURE Press the „ “ or „ “ button for adjusting the Temperature.

less 6 SETTINGS

NIGHT LIGHT pull for adjusting the night light, pull out the contol-knob and turn it anti clockwise the night light model will change like: turn Night light out --> Night light always on --> Night light smart mode.

The smart mode refers that the night light will light up in a dark environment and light off in a bright environment.

AMBIENT LIGHT pull Open the cover and be unseated, pull the knob and rotate it in the clockwise direction . The ambient light will be lighted off. It will be lighted up when rotating it in the clockwise direction again turn

POWER OF SETTING

Keep pressing the middle button of the knob for more than 6seconds, it will go into power standby mode. Press again the button for more than 6 seconds to restart it.

7 NOZZLE CLEANIG

1. The nozzle will be cleaned before washing and after washing.

2. Manual cleanig Open the cover and seat then rotate the knob in the clockwise direction.Then the nozzle will extend with cleaning water. It will return after 5 minutes or press the " stop " button .

A B C

D E

SELF-CLEANIG TANK

Not used for more than 72 hours, when the user operates the washing ,it will open the self-cleaning for about 30 seconds. All the buttons are invalid during the self- cleaning and it will return to normal after the self-cleaning

8 RELEASE AND INSTALL COVER AND SEAT

A B

C D

9 TROUBLESHOOTING

melborP laitnetoP esuac detsegguS noitca

.1 The power supply may not be opened esaelP nrut no eht rewop The electronic bidet cannot please open the inlet water valve,or check if there is without water 2. The water supply may not be opened work supply 3.Maybe not in the seating state Please sit on the seat and adjust sitting position 1.The washing cycle is 3 mins. It will stop This is normal and please return the knob to start washing again washing after 3 mins then the nozzle will go The nozzle goes back 2.There may be some problems of water supply Please check if there is without water supply suddenly 3.Maybe the user stand up and leave the seated Please sit down and adjust sitting position sensor area. Please increase the flow rate as per "adjusting water flow rate" of 1.The water flow rate may be set at low grades operating instructions. Low water flow rate 2.The water supply pressure may be too low Please check and ensure the water supply pressure is 0.07Mpa

Please set the water temperature at high grade as per "adjusting Low water temperature The water temperature may be set at low grades temperature"of operating instructions. When start washing function, the nozzle will do The nozzle comes out slow self-cleaning before coming out, and this will take This is normal. a few seconds When the night light is set at smart mode,the night light will not work 1.Maybe in the bright environment. when in the bright environment. Night light cannot work Please open the night light function and adjust the night light mode as 2.The night light function may be closed. per "Light Setting" of operating instructions. When the night light is set at smart mode,the night light will be always 1.Maybe in the dark environment. on when in the dark environment. Night light is always on 2.Something may be covered around the knob. Clean the obstructions around the knob. Please adjust the night light mode as per "Light Setting" of operating 3.The night light may be set at always on mode instructions. 1.The nozzle goes back after washing 5 minutes. This is normal. The nozzle goes back automaticly when manual ebyaM.2 sserp bonk ehT launam gninaelc lliw eb deppots fi sserp eht bonk . cleaning 3.Maybe the seated sensor detected that it is in Please do not put down the seat during the manual cleaning the seating state The light flash twice with Please shut off the power and water supply,stop using the The water temperature may be too high. constantly "beep" product,and then contact local distributor Please check if the power and water supply are normal,cut off the The light around the knob keep There may be something wrong with the product. power for 1 minute then restart the product. If the product still cannot flashing work,please contact local distributor.

Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact you local government for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being. When replacing old appliances with new ones, the retailer is legally obligated to take back your old appliance for disposals at least free of charge.

10