DOCSLIB.ORG

RVZ03-ARGB Manual

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
RVZ03-ARGB Manual RVZ03-ARGB REREDEFIEFINE SFFFF COMCOMPUTITING WITHWITH FLAIAIR Signature RAVEN styled front panel adorned with addressable RGB light strip INTRODUCTION SilverStone RVZ03 is a further evolution of the highly rated RAVEN Z RVZ01-E, a slim form factor case with tremendous capability. It has the same optimized interior that has room for a standard ATX (PS2) power supply and support for some the biggest consumer graphics cards on the market with superb air cooling performance. Designed for use in either vertical or horizontal orientation, it can be placed comfortably in any space-constrained environment that requires a powerful PC. For those looking to build a slim form factor PC with extra flair, the RVZ03’s inclusion of addressable RGB lighting and controller bring about another exciting chapter to the famed RAVEN series of computer cases. SPECIAL FEATURES Signature RAVEN styled front panel adorned with addressable RGB light strip Mini-ITX motherboard & ATX PSU compatible for wide array of building possibilities Support cards up to 13 inches (330mm) to fit most high-end GPUs for compute power far exceeding consoles Maximum performance in slim form factor with support for AIO liquid cooling Positive air pressure design for excellent cooling/quietness and dust-prevention Fits in nearly any environment with horizontal or vertical orientation SPECIFICATIONS Model SST-RVZ03B-ARGB (black), SST-RVZ03W-ARGB (white) Material Reinforced plastic outer shell, steel body Motherboard Mini-DTX, Mini-ITX Drive Bay Internal 2.5" x 3 Cooling System Top 1 x 120mm fan, 1500rpm, 18dBA Bottom 1 x 120mm fan, 1500rpm, 18dBA 1 x 120mm fan slot Expansion Slot 2 Front I/O Port USB3.0 x 2, Audio x 1, MIC x 1 Power Supply Optional PS2 (ATX) Expansion Card Compatible up to 13" (330mm) long, width restriction-5.88" (149mm) Limitation of CPU cooler 83mm Limitation of PSU 150mm* Net Weight 4.05kg Dimension 382mm (W) X 105mm (H) X 364mm (D) , 14.6 liters Extra Support Kensington lock, PCI Express riser card set x 1 ARGB control PCB x 1 * Maximum length for power supply is 150mm but we recommend 140mm deep power supply due to varying connector locations and the unique structure of RVZ03. Due to the use of internal power cord extension, we recommend not to exceed 800W when powering off a 110V outlet (no limit for 220V). DISASSEMBLE CHART 2.5" HDD X1 2.5" HDD X2 TOP COVER FAN FILTER X1 12015 FAN X1 ARGB CAGE FAN FILTER X2 MINI-ITX (OPTION) POWER CAGE RESET BUTTON HDD LED POWER BUTTON POWER LED USB 3.0 + SPK + MIC 12015 FAN X1 ATX PSU (OPTION) ITEM PURPOSE RUBBER-A-FEET PAD FOR VERTICAL USE RUBBER-E-FEET PAD FOR HORIZONTAL USE TOP-CARD-BKT BOTTOM-CARD-BKT LOGO-HORIZONTAL-PAD VGA-COMP-BELOW-RUBBER SCREW C 632 X8 SECURE VGA SUPPORT BRACKET SCREW D M2 X2 SECURE OPTICAL DRIVE SCREW E 632 X5 SECURE MOTHERBOARD, PSU SCREW F M3 X4 SECURE 2.5" SSD/HDD BAG PCI-EXTEND-CARD SCREW A O4 X15-M3 X4 SECURE RADIATOR COOLING FAN SCREW B O4 X15-632 X4 SECURE RADIATOR COOLING FAN CONTROLLER CABLE ARGB SIGNAL CONTROLLER CONTROL PANEL CABLE ADOPTER CABLE INSTALLATION GUIDE Before you begin, please make sure that you Have all components collected. Check that all components do not have compatibility problems with each other or with the case. If possible, assemble the components outside the case first to make sure they are working. Keep the motherboard manual ready for reference during installation. Prepare a Philips screwdriver. Be careful not to strike on glass side panel when removing it from the case. 1 Unscrew the screws from the rear of the chassis then remove the top cover 2 Unscrew the screws from the graphics card support bracket then remove it 3 Unscrew the screws from PSU bracket then remove it 4 If you want to use SilverStone NT06-PRO or other similar CPU cooler, please relocate the top panel 120mm fan to the bottom vent near the graphics card area 1 2 5 Insert the I/O shield included with your motherboard then install the motherboard into the chassis 6 We recommend at this point connecting all the necessary cables including the SATA cables to the motherboard 7 Secure the PSU into the PSU bracket 8 Place the PSU bracket on top of the chassis then connect the power cord to the PSU 9 Insert the PSU bracket into its original position and secure with screws 10 Remove expansion slot cover and install graphics card into the graphics card support bracket 11 Depending on the design of your graphics cards, install and adjust the graphics card holder to a proper position to support your card. Adhere included rubber padding according to the height of graphics card’s backside, one (for 3mm thick backplate) or two (for no backside components) Included Foam Pad 12 Install 2.5" HDD/SSD onto the graphics card support bracket 13 Connect addressable RGB (ARGB) connector. Please refer to ARGB LED connector guide in later pages for more details 14 Install graphics card support bracket into the chassis and connect the power cord to the graphics card if needed 15 Make sure all the cables are properly connected 16 Place the top cover back onto the chassis and secure with screws 17 Depending on requirement or preference, adhere four rubber stands for horizontal use or install the rubber pads for vertical use. Corresponding RAVEN logo for each orientation are included for installation CONNECTOR DEFINITION (1) Front Panel Connectors Guide Power Switch Reset Switch Power switch and reset switch installation guide Please refer to the motherboard manuals for the motherboard’s “Front Panel Connector” or “System Panel Connector” pin definition Power switch and reset switch have no polarity, so they can be connected in any orientation LED indicators installation guide HDD LED+ HDHDDD LED-LED Please refer to the motherboard manuals for the motherboard’s “Front Panel Connector ” or “System Panel Connector” pin definition; the white/black wires are negative while other colors are positive wires (2) ARGB LED connector guide RVZ03-ARGB includes custom ARGB controller. It has dual modes that enables you to control lighting effect either via software (provided by motherboard) or hardware. Software control : A. To control lighting via motherboard, make sure it supports addressable RGB (+5V, D, G) signals on its RGB header. B. If you have other ARGB devices such as SilverStone’s own LS03 light strip or FG122 ARGB fan frame, you may also connect them to RVZ03’s ARGB controller, below are installation steps: 1. Flip the controller switch to “MB” mode 2. Connect motherboard ARGB signal cable to motherboard 3. If needed, use included extension cable 4. When connecting non-SilverStone ARGB products, make sure pin definition and connector orientation are compatible Hardware control: Utilizing the case’s reset button to change lighting effects 1. Flip the controller switch to “IC” mode 2. Connect other ARGB devices to RVZ03’s ARGB controller 3. When connecting non-SilverStone ARGB products, make sure pin definition and connector orientation are compatible 4. Connect the controller to power supply 5. Be sure not to connect case’s reset connector to motherboard as you are going to use reset button for changing ARGB colors and effects from now on 6. When PC is powered, press reset button on the case to change ARGB lighting effects (3) Front I/O connector guide Below are the front I/O connectors pin definition, please also check your motherboard manual to cross reference with motherboard’s front I/O pin headers. SilverStone’s I/O connectors are in block type to simplify installation USB 3.0 CONNECTOR Pin 1 Pin 19 Vbus IntA_P1_SSRX- Vbus IntA_P1_SSRX+ IntA_P2_SSRX- GND IntA_P2_SSRX+ IntA_P1_SSTX- GND IntA_P1_SSTX+ IntA_P2_SSTX- GND IntA_P2_SSTX+ IntA_P1_D- GND IntA_P1_D+ IntA_P2_D- ID IntA_P2_D+ Pin 10 Pin 11 HD CONNECTOR AUD GND PORT1L PRESENCE PORT1R SENSE1_RETURN PORT2R PIN SENSE_SEND SENSE2_RETURN PORT2L PIN COMPONENT SIZE LIMITATIONS (1) CPU cooler height limitation 83mm 11mm 4.2mm A. Height limitation: The RVZ03 has 83mm height limitation for CPU cooler B. Upper boundary: the cooler can protrude 11mm over the motherboard’s top edge C. Front boundary: The clearance toward the front of the chassis is 4.2mm (2) PSU limitation RVZ03’s maximum depth for a standard PS/2 (ATX) power supply is 150mm, but installation of a 150mm deep power supply will require sacrificing a 2.5" drive space and no room for cable connection after installation. So if using a 150mm deep modular power supply, make sure to connect all cables prior to installing it into the case. Power supplies with depth of 140mm or less may have enough room to allow for cable connection after installation so we recommend using 140mm deep modular power supply with flat cables, such as SilverStone’s own ST75F-PT (3) Graphics card/expansion card length limitation iii 149mm ii 131mm i 111mm A. Length limitation RVZ03 can support 13" (330mm) consumer level graphics cards. Please contact us if you find a card that does not fit B. Width limitation (i) The standard width for graphics card is 4.38" (111mm) (ii) With the graphics card holder installed, the maximum allowable width for graphics card is 5.16" (131mm) (iii) Without the graphics card holder, the maximum allowable width for graphics card is up to 5.88" (149mm) i ii iii 3.23mm 34.8mm 68mm 32mm C. Thickness limitation (i) Calculated from the bottom of the graphics card PCB to the top, the total thickness limitation is 68mm (ii) With the standard 34.8mm-thick dual slot graphics card installed, the maximum thickness of the fans is 32mm (iii) The thickness of the components on the back of the graphics card is limited to 3mm in the area supported by the graphics card holder; the thickness limitation for the rest of the components is 10mm OPTIMAL THERMAL PERFORMANCE LAYOUT If you use graphics card with omni-direction or open air cooler, we recommend having two case fans on the bottom vents VERTICAL/HORIZONTAL PLACEMENT A.
Load more

Recommended publications
  • S1 Supplementary Information Novel Fluorescent Lapachone-Based BODIPY
    Electronic Supplementary Material (ESI) for ChemComm. This journal is © The Royal Society of Chemistry 2016 Supplementary Information Novel fluorescent lapachone-based BODIPY: Synthesis, computational and electrochemical aspects, and subcellular localisation of a potent antitumour hybrid quinone Talita B. Gontijo,a Rossimiriam P. de Freitas,a Guilherme F. de Lima,a Lucas C. D. de Rezende,b Leandro F. Pedrosa,c Thaissa L. Silva,d Marilia O. F. Goulart,d Bruno C. Cavalcanti,e Claudia Pessoa,e,f Marina P. Bruno,g José R. Correia,g Flavio S. Emeryb* and Eufrânio N. da Silva Júniora* aInstitute of Exact Sciences, Department of Chemistry, Federal University of Minas Gerais, CEP 31270-901, Belo Horizonte, MG, Brazil; bFaculty of Pharmaceutical Sciences, University of São Paulo, CEP 14040-903, Ribeirão Preto, SP, Brazil; cInstitute of Exact Sciences, Department of Chemistry, Fluminense Federal University, CEP 27213-145, Volta Redonda, RJ, Brazil; dInstitute of Chemistry and Biotechnology, Federal University of Alagoas, CEP 57072-970, Maceió, AL, Brazil; eDepartment of Physiology and Pharmacology, Federal University of Ceará, CEP 60180-900, Fortaleza, CE, Brazil; fFiocruz-Ceará, CEP 60180-900, Fortaleza, CE, Brazil; gInstitute of Chemistry, University of Brasília, CEP 70904970, Brasília, DF, Brazil. E-mail: [email protected], [email protected] Contents Chemistry S2 NMR spectra of compounds S6 HRMS spectra S14 Photophysical Parameters S15 Cell Staining Procedure S18 Cytotoxicity against cancer cell lines – MTT assay S27 Analysis of reduced glutathione content and TBARS assay S29 Electrochemical studies S31 Computational details S35 S1 Chemistry Materials and methods Melting points were obtained on Thomas Hoover and are uncorrected. Analytical grade solvents were used.
    [Show full text]
  • Silverstone SG06B Premiere Mini-ITX/Mini-DTX Small Form
    1701 R. J. Conlan Blvd. NE, Unit #5 Like Us Facebook See Our Instagram Palm Bay, FL 32905, USA Toll Free: 888-381-8222 Follow Us Twitter Watch Our YouTube Performance-PCs.com www.performance-pcs.com [email protected] SilverStone SG06B Special Price $91.96 was Premiere Mini-ITX/Mini-DTX $114.95 Small Form Factor Case w/ 300W PSU - Silver Product Images 1 10/3/21 Short Description Designed for use with Mini-DTX and Mini-ITX motherboards, the SG06, like the SG05 is the smallest Sugo yet. Compared with Micro-ATX iterations at around 23 liters in volume, the SG06 at 11.1 liters is less than half the size! In keeping with the spirit of its Sugo name, the case is capable of swallowing many standard components while keeping everything cooled. The SG06 is equipped with a low speed 120mm fan that utilizes golf blades for exceptional quietness to airflow. As in the SG05, the fan is mounted in the front drawing air into the case to create positive air pressure cooling. Description Product Details: Designed for use with Mini-DTX and Mini-ITX motherboards, the SG06, like the SG05 is the smallest Sugo yet. Compared with Micro-ATX iterations at around 23 liters in volume, the SG06 at 11.1 liters is less than half the size! In keeping with the spirit of its Sugo name, the case is capable of swallowing many standard components while keeping everything cooled. The SG06 is equipped with a low speed 120mm fan that utilizes golf blades for exceptional quietness to airflow.
    [Show full text]
  • Analysis and Experiment on Multi-Antenna-To-Multi-Antenna RF WPT
    Received December 21, 2020, accepted December 22, 2020, date of publication December 25, 2020, date of current version January 6, 2021. Digital Object Identifier 10.1109/ACCESS.2020.3047485 Analysis and Experiment on Multi-Antenna-to- Multi-Antenna RF Wireless Power Transfer JE HYEON PARK, (Student Member, IEEE), DONG IN KIM , (Fellow, IEEE), AND KAE WON CHOI , (Senior Member, IEEE) Department of Electrical and Computer Engineering, College of Information and Communication Engineering, Sungkyunkwan University, Suwon 16419, South Korea Corresponding author: Kae Won Choi ([email protected]) This work was supported in part by the National Research Foundation of Korea (NRF) funded by the Ministry of Science, ICT and Future Planning (MSIP), Korean Government under Grant 2014R1A5A1011478, and in part by the Basic Science Research Program through the National Research Foundation of Korea (NRF) funded by the Korean Government (MSIP) under Grant NRF-2020R1A2C1014693. ABSTRACT In this paper, we provide a tool for predicting the power transfer efficiency of radio-frequency (RF) wireless power transfer (WPT). With its capability of long-range wireless power transfer, RF WPT is considered as a very promising recharging technique for powering low-power internet of things (IoT) devices. The prediction of the power transfer efficiency is a prerequisite for setting up a proper design goal of RF WPT systems. We propose an analytic method that enables to calculate the efficiency in various multi- antenna-to-multi-antenna WPT scenarios with arbitrary positions and attitudes of antenna arrays. We have built a prototype RF WPT system with 64 transmit and 16 receive antennas, the operating frequency of which is 5.8 GHz, and verified the accuracy of the proposed analysis.
    [Show full text]
  • Gvic SX2380 Book.Book
    Gateway SX2830 Service Guide SG V1.01 PRINTED IN TAIWAN Revision History Please refer to the table below for the updates made on this service guide. Date Version Chapter Updates 04-25-2012 First Draft 04-26-2012 V1.00 08-20-2012 V1.01 1,2,6 Phase in Win8 operation system, and update related information on page1, 15, 16, 98. ii Copyright Copyright © 2012 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated. iii Disclaimer The information in this guide is subject to change without notice. Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Acer is a registered trademark of Acer Corporation. Other brand and product names are trademarks and/or registered trademarks of their respective holders. iv Conventions The following conventions are used in this manual: SCREEN Denotes actual messages that appear on screen. MESSAGES NOTE Gives additional information related to the current topic.
    [Show full text]
  • Node 605 the Node 605 Highlights a Minimalistic, Sleek Scandinavian Appeal Which Is Designed to Integrate Into Your Home Theatre Equipment
    Product Sheet Node 605 The Node 605 highlights a minimalistic, sleek Scandinavian appeal which is designed to integrate into your home theatre equipment. Featuring a stunning exterior appearance accompanied by a modern, black interior with sound and vibration dampening materials, the Fractal Design Node 605 supports a full ATX motherboard as well as a graphics card up to 280mm in length. Cleverly hidden behind the access panel on the solid 8mm thick aluminum front panel are two USB 3.0 ports, a FireWire port and a multi-format card reader for multiple formats. Key features • Solid aluminum front panel • Supports full ATX motherboards • Noise-dampening material • 4 HDD/SSD slots • Integrated card reader • Two Silent Series R2 hydraulic bearing fans included • Supports graphic cards up to 280mm in length (180mm with all hard drives in place) • USB 3.0 and FireWire front connectors Fractal Design brings you scandinavian design and quality www.fractal-design.com Product Sheet General Specifications Motherboard compatibility • ATX, microATX, Mini ITX, DTX Front interface • 2 - USB 3.0 • 1 - FireWire (IEEE 1394) • 1 - 3.5mm audio in (microphone) • 1 - 3.5mm audio out (headphone) • Power button with LED • HDD LED HDD / SSD slots • 4 - supports either 2.5” or 3.5” HDD / SSD ODD slots • 1x 12.7mm slim/slimline ODD (only supported with mATX or smaller motherboards) Expansion slots • 7 PSU compatibility • 180 mm (including any modular connectors) with both hard drive cages mounted • 190 mm (excluding cables and any modular connectors) with one hard
    [Show full text]
  • The Benchmark for Small Form Factor Value
    SUGO The benchmark for small form factor value SG13B-Q SG13B Special Features Support standard-length expansion cards (10.5 inches) Mini-DTX / Mini-ITX motherboard & ATX PSU compatible Support 120mm or 140mm single fan All-in-One Liquid Cooler Support 2.5” and 3.5” hard drives Elevated standoff for motherboard back side components HEADQUARTERS USA EUROPE Model No.: SST-SG13B 12F.,NO.168,Jiankang Rd., Zhonghe Dist., 13626 Monte Vista Ave.Unit A, Chino, Brandstücken 43, D-22549 Hamburg SST-SG13B-Q New Taipei City 235, Taiwan R.O.C. CA 91710, USA Germany Tel: +886-2-8228-1238 Tel: +1-909-465-9596 Tel: +49-40-675931-0 Fax: +886-2-8228-7123 Fax: +1-909-465-9596 Fax: +49-40-675931-66 www.silverstonetek.com SUGO The benchmark for small form factor value SG13 Introduction After bringing Mini-ITX into mainstream DIY (do it yourself) market in 2009 with the Sugo SG05, SilverStone is looking to define the category again with SG13, a newly evolved design that aims to satisfy every type of computer users. At only 11.5 liters in size, it has suitably small statue for easily integrating into numerous computing environments and will comfortably fit many standard components for general purpose or office builds. For enthusiasts and in keeping with Sugo series’ famed tradition, the SG13’s ability to fit 10.5” long expansion card, standard ATX power supply, and all-in-one liquid cooler in 120mm or 140mm size will help produce amazingly small and powerful systems. Feature Photos Support standard-length Mini-DTX / Mini-ITX Support 120mm or Support 2.5” and 3.5” Elevated standoff expansion cards motherboard & ATX PSU 140mm single fan hard drives for motherboard back (10.5 inches) compatible All-in-One Liquid Cooler side components Specifications Model No.
    [Show full text]
  • Carmen Rodríguez Capilla Francesco Quacquarelli Definición Del Factor De Forma
    Los factores de forma Carmen Rodríguez Capilla Francesco Quacquarelli Definición del factor de forma El Factor de forma (inglés form factor) es el tamaño físico estandarizado de una placa base para ordenador personal. También define algunas especificaciones la placa base. Estas características se definen para poder integrar la placa madre con el resto de los dispositivos. El factor de forma define: • Forma de la placa madre: cuadrada o rectangular. • Ancho y largo de la placa madre. • Posición de los anclajes (ubicación de tornillos). • Áreas donde se sitúan los componentes (ranuras de expansión, conectores y puertos). • Forma física del conector de la fuente de alimentación y las conexiones eléctricas. Las placas base van ha ser creadas en función del factor de forma y ya que existen difernetes tipos de factores de forma estándares van a surgir diferentes tamaños de placas base, diferentes dimensiones físicas de la fuente de alimentación, según la placa y diferentes tipos de conectores de la alimentación con los que se va a suministrar la energía. Es por todo esto por lo que las cajas ('case') van a ser diseñadas para contener uno o varios tipos de placas base y van a contar con las ranuras apropiadas para su instalación. Surgen, de este modo: − placas estándar con factor de forma XT, AT, ATX, AT Baby, BTX, WTX, etc... − placas propietarias que son las propias de algunos fabricantes de ordenadores. Origen del factor de forma El factor de forma nació de la necesidad de crear un standard para que los componentes de un ordenador sean intercambiables entre si, indiferentemente del fabricante.
    [Show full text]
  • Formaty Płyt Głównych
    Formaty płyt głównych ₥@ʁ€₭ ‽ud3£k0 Urządzenia Techniki Komputerowej Spis treści • Budowa modułowa • DTX • Podział płyt głównych • ITX • IBM PC Motherboard • ETX • • XT XTX • WTX • AT • Płyta główna dla • LPX górników • NLX • Formaty • ATX przyszłościowe • BTX – ASUS Utopia 2 Koncepcja budowy modułowej • Budowa modułowa (model otwarty) polega na tym, że komputer można zestawić z wybranych elementów i dopasować do potrzeb (i finansów). – Poszczególne części muszą być ustandaryzowane, by pasowały do siebie. • Standardy płyt głównych pozwalają na umieszczanie określonych kart rozszerzeń. – Obudowy komputerów muszą być dopasowane do danego typu płyty. 3 Idea budowy modułowej 4 Wymiary płyty głównej Otwory na śrubki mocujące wymiarami do obudowy wymiarami Interfejsy zewnętrzne pasujące zewnętrzne Interfejsy Złącza, gniazda i wtyki znormalizowane 5 PODZIAŁ PŁYT GŁÓWNYCH 6 Płyta główna WTX ETX AT ATX BTX ITX DTX LPX NLX Baby AT Micro BTX Mini ITX Mini DTX Nano ITX Pico BTX Pico ITX EATX Ultra ATX Flex ATX EEATX Mobile ITX Micro ATX Mini ATX Neo ITX 7 Zestawienie płyt pod względem rozmiaru WTX 356×425 Micro ATX 244×244 ESM 149×71 AT 350×305 Pico BTX 267x203 Nano-ITX 120×120 EEATX 347x330 DTX 244×203 COM Express 125×95 Enhanced EATX Baby-AT 330×216 Flex ATX 229×191 ESM express 125×95 BTX 325×266 Mini-DTX 203×170 ETX/XTX 114×95 SSI CEB 305x267 EBX 203×146 Pico-ITX 100×72 EATX 305×330 Micro ATX 171×171 PC/104 (-Plus) 96×90 (Extended ATX) (min.) LPX 330×229 Mini-ITX 170×170 ESMini 95×55 ATX 305×244 Neo-ITX 170x 85 Qseven 70×70 micro BTX 264×267 GLKD-HTI 170x 85 mobile-ITX 60×60 NLX 254×228 EPIC (Express) 165×115 CoreExpress 58×65 Ultra ATX 244×367 Mini ATX 150×150 8 Rozmiary płyt głównych - porównanie 9 10 FORMATY PŁYT GŁÓWNYCH 11 Płyta główna IBM PC Motherboard • IBM „planar” Breadboard • Pierwsza nowoczesna płyta główna wyprodukowana przez IBM dla komputerów osobistych IBM PC w 1981 roku.
    [Show full text]
  • SUGO14-Product Sheet-EN
    SUGO 14 Mini-ITX cube chassis with configurable front panel • Supports 3 slot full length graphics cards with adjustable graphics card holder Exceptional usability • Compatible with Mini-DTX / Mini-ITX motherboard & ATX PSU & upgradability • Supports up to 240mm radiators • Modular design with 4 removable panels (top, left, right, bottom) • Different configurations support various storage components for 5.25", 3.5" and 2.5" • Front I/O port includes: USB 3.0 x 2, USB 2.0 x 1, combo audio x 1 Specifications Model No. SST-SG14B Material Plastic front panel, steel body Color Black Motherboard Mini-DTX, Mini-ITX Drive bay External 5.25" x 1 (without radiator and 3.5" x 1 installed) Internal 3.5" x 2 (without radiator and 5.25" installed) 2.5" x 3 Cooling system Rear 120mm / 140mm x 1 (120mm x 1 black fan included) Side 120mm / 140mm x 2 Radiator support Rear 120mm Side 120mm / 240mm Expansion slot 3 Front I/O port USB 3.0 x 2, USB 2.0 x 1, Combo audio x 1 Power supply Standard PS2 (ATX) Graphics card limit Length: 330mm Width: 148mm CPU cooler limit Air cooler: 182mm (without top fan) 240mm AIO water block: 55mm PSU limit 150mm Net Weight 4.89 kg Dimension 247mm (W) x 215mm (H) x 368.1mm (D), 19.55 Liters 9.72" (W) x 8.46" (H) x 14.49" (D), 19.55 Liters www.silverstonetek.com High compatibility with no compromise Unlike most SFF Mini-ITX chassis on the market, SUGO 14 is capable of fitting a 3 slot full length graphics cards on the left side and up to 240mm radiators on the right side.
    [Show full text]
  • Universal Housings - UCS 237-195-H-GD 9005 - 2203345 Please Be Informed That the Data Shown in This PDF Document Is Generated from Our Online Catalog
    https://www.phoenixcontact.com/pi/products/2203345 Universal housings - UCS 237-195-H-GD 9005 - 2203345 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://phoenixcontact.com/download) Complete housing for PCBs, can be positioned flexibly; includes housing half shells, side panels closed, adhesive domes for PCB attachment, screws for housing and PCB attachment; housing: black with turquoise blue corner inlays Your advantages High degree of application flexibility, thanks to the modular housing design Flexible PCB attachment, adapts to virtually all form factors Practical customization options Reduced logistics outlay, thanks to components which are compatible with one another Key Commercial Data Packing unit 1 pc GTIN GTIN 4055626404554 Technical data Item properties Type UCS 237-195-H-GD 9005 Order No. 2203345 Housing type Universal housings Type Tall design Max. IP code to attain IP40 Ventilation openings present no Measurements Width [ w ] 237 mm Height [ h ] 195 mm Depth [ d ] 67 mm Dimensions 212 mm x 170.2 mm (Maximum circuit board dimensions) 09/12/2020 Page 1 / 10 https://www.phoenixcontact.com/pi/products/2203345 Universal housings - UCS 237-195-H-GD 9005 - 2203345 Technical data Material specifications Color (RAL) black (9005) Flammability rating according to UL 94 V0 Housing material PC Ambient conditions Ambient temperature (storage/transport) -40 °C ... 55 °C Ambient temperature (assembly) -5 °C ... 100 °C Ambient temperature (operation) -40 °C ... 100 °C (depending on power dissipation) Relative humidity (storage/transport) 80 % PCB data Number of PCB holders 1 This product is prepared for a printed-circuit board.
    [Show full text]
  • Sliger Cerberus X ATX/EATX Computer Chassis
    1701 R. J. Conlan Blvd. NE, Unit #5 Like Us Facebook See Our Instagram Palm Bay, FL 32905, USA Toll Free: 888-381-8222 Follow Us Twitter Watch Our YouTube Performance-PCs.com www.performance-pcs.com [email protected] Sliger Cerberus X $265.00 ATX/EATX Computer Chassis Product Images 1 10/8/21 2 10/8/21 3 10/8/21 Short Description Cerberus X is the worlds smallest ATX/ EATX PC case on the marking measuring in at roughly 14.97" x 6.78" x 14.09", But don't let its size fool you this Mini Chassis is build for hard work with its ability to be fully customizable this chassis is perfect for a LAN Party Rig or just for every day use. Please Note: These cases will take up to 1 Week to be assembled and shipped. Description Cerberus X is the worlds smallest ATX/ EATX PC case on the marking measuring in at roughly 14.97" x 6.78" x 14.09", But don't let its size fool you this Mini Chassis is build for hard work with its ability to be fully customizable this chassis is perfect for a LAN Party Rig or just for every day use. Please Note: These cases will take up to 1 Week to be assembled and shipped. Features Support for ATX, EATX, Mini-DTX, and Mini-ITX motherboards Compatible with air coolers up to 148mm tall (with side hinge bracket removed) Interchangable power supply mounting options for SFX, SFX-L, and ATX power supplies (8x) PCIe Expansion Card Slots for quad SLI/Crossfire/Quadro Sync support (up to 330mm long x 150mm tall) Ability to mount up to two 280mm radiators for water cooling setups Infinite vent design for mounting of any and
    [Show full text]
  • AMD Empowers PC Industry to Deliver Innovative Small Form Factor Solutions with DTX and New Energy-Efficient Processors
    June 5, 2007 AMD Empowers PC Industry to Deliver Innovative Small Form Factor Solutions With DTX and New Energy-Efficient Processors Open Standards Approach Enables Aesthetically-Pleasing Platform Solutions That Combine Leading-Edge Performance With Reduced Power Consumption TAIPEI, Taiwan--(BUSINESS WIRE)-- Further advancing the availability of energy-efficient platforms, at Computex today, AMD (NYSE:AMD) announced the finalization of the DTX specification, an open standard initiated by AMD to enable the development of small form factor PCs. AMD also introduced new 45- watt energy-efficient processors based on 65nm technology, the AMD Athlon(TM) X2 dual- core processor BE-2350 and the AMD Athlon X2 dual-core processor BE-2300. These innovations help AMD deliver on its commitment to lead the world to energy efficient processing by empowering OEMs and system builders to deliver smaller, quieter computing solutions for the home or office desktop, as well as other locations throughout home. Industry partners including Albatron, Asus, Cooler Master, ECS, Gigabyte, MSI, Silverstone, and Thermaltake are demonstrating functional DTX demonstration platforms at AMD Booth #TF1I at Computex, Hall 4 TICC with the intent to deliver systems later in 2007. "AMD remains committed to enabling our ecosystem partners, and the ecosystem as a whole, to develop systems that are not only energy-efficient, but also visually compelling for end users," said Bob Brewer, corporate vice president and general manager, Desktop Division, AMD. "Our leadership of the DTX
    [Show full text]