Empty the condensation container Your dryer Intended use Preparation Installation aInstallation and maintenance instructions, Page 1 Drying Display panel and buttons Information on ... If the condensation drain is installed, it is not necessary to Display panel Congratulations! - You have chosen a modern, high-quality domestic ʋ For domestic use only. Never start the dryer if it is damaged. empty the condensation container. a separate ʑ Labelling of fabrics appliance from Siemens. ʋ Only to be used for drying, refreshing or unwrinkling Inform your after-sales service. Inspect the dryer Instructions for condensation drain. Please clean lint Clean the fluff filters a Page 4. Follow the manufacturer's care instructions.

filter fabrics.of WT48Y890DN

One distinctive feature of the condensation dryer with heat pump and he programme

fabrics that have been washed with water. on the othing. automatic cleaning of the heat exchanger is its low energy Empty the container after each drying cycle, and not during Please empty Empty the condensation container a Page 4 and/or clean the filter in the condensation hcSuitable for tumble drying s. Do not leave children vidual items of consumption. 7 the cycle. condensate container a Installation and maintenance instructions, Page 3. ( Dry at normal temperature. unsupervised near the dryer. Make sure your hands are dry. . Every dryer which leaves our factory is carefully checked to ensure 1. Remove the container, holding it level. container 'cDry at low temperature. Keep pets away from the dryer. Hold the plug only. Connect the that it functions correctly and is in perfect condition. 2. Pour out the condensed water. Push the container back Refresher-container Fill the refresher tank with distilled water for steam programmes a Page 8. )cDo not tumble dry. The dryer can be operated by children 8 years old mains plug in until it clicks into place. Should you have any questions, our after-sales service will be happy is empty, please re- Do not tumble-dry the following fabrics: to help. and older, by persons with reduced physical, You must also observe the a Installation and maintenance fill. sensory or mental abilities and by persons with instructions, Page 3. – Non-breathable fabrics (e.g. rubber-coated). see Basketthe for woollens and the notes on Page 6. Fascia panel Carl-WeryStr. 34 Heat exchanger is Automatic cleaning of the heat exchanger. Do not empty the condensation container while this is – Delicate materials (silk, curtains made from synthetic material) a these may crease. insufficient experience or knowledge if they are a Environmentally-responsible disposal Sort the laundry Condensation being rinsed displayed. supervised or have been instructed in its use by container with filter – Oil-stained laundry. Dispose of packaging in an environmentally-responsible manner. a responsible adult. Remove all items from pockets. Door Clean the fluff filters Buttons This appliance is designated according to European directive Check for cigarette lighters. ʑ Drying tips Õü(Drying target) Select the dryness level (e.g. C/board Dry) or the drying time

2002/96/EC, which governs waste electrical and electronic The drum must be empty prior to loading. SiemensElectrogeräte GmbH Clean fluff filters reduce energy consumption. (20 mins up to 3 hrs 30 mins., depending on the model and programme). – To ensure a consistent drying result, sort the laundry by fabric type and drying programme. 81739München/Deutschland equipment - WEEE). See programme overview on page 7. C/board Dry Extra: For laundry with thick, multi-layered parts. – Always dry very small fabrics (e.g. baby socks) together with The directive provides an EU-wide framework for the return and The fluff filter consists of two parts. large items of laundry (e.g. towels). recycling of used appliances. + C/board Dry: For single-layered laundry. Programmes / Fabrics 6 Clean the inner and outer fluff filter Ô Iron Dry: The condition of the laundry means it is suitable for (iron clothes in order – Close zips, hooks and eyelets, and button up covers. Detailed overview of the programmes and fabrics after every drying cycle. to avoid creases). Tie cloth belts, apron strings, etc. together or use a laundry bag. For further information about our products, accessories, spare parts a Programme overview, Page 7. Î (Less Ironing) After the programme finishes, the drum moves at regular intervals to prevent creases. The – Do not over-dry easy-care laundry a Risk of creasing. and services, please visit: www.siemens-home.com. Observe the care instructions on the care label. Allow laundry to finish drying in the air. Dryness level, timer programming and options can be 1. Open the door. Remove fluff from the automatic anti-crease function can be set in 30-minute segments up to 120 minutes. The longerdrying time than single-layered items of cl Options and notes description. For pre-dried, multi-layered fabrics or small, indi laundry. Also for subsequent drying. Automatic detection of residual moisture and drying Particularly gentle. Easy-to-dry textiles. For refreshing fabrics only. Observe carethe label Only for unwrinklng fabrics.of Best results can be expected "Non-iron"if appears manufacturer's label; remove the items as soon as t ends. individually selected depending on the selected programme The dryer is switched on and off by pressing the  button in the centre of the Open the door/load the laundry/ door/door area. standard setting for each programme is 60 minutes. – Do not iron laundry immediately after drying; fold items up and leave for a while Use with separate basket only and the progress of the programme. Pull out the inner (Finished in) When a programme is selected, the anticipated drying time for the maximum load is displayed. a residual moisture will then be distributed evenly. programme selector. 1 2. Iron Dry (depending on the model andprogramme) Select the programme by turning the outer ring on the programme selector (the press the programme selector/ and outer fluff filter While drying, the moisture sensors detect the actual load and correct the programme length. This – Knitted fabrics (e.g. T-, jerseys) often shrink slightly the first time they are tumble-dried.

Cotton Hard-wearing fabrics Ô selector can be turned in both directions). The selected programme is displayed. and open them out. is shown in the display by jumps in the (Finished in) time. aDo not use the  C/board Dry Extra programme. Easy Care Fabrics made from synthetic or set the programme The (Finished in) time can be delayed in one-hour steps, up to a maximum of 24 hours. Press – Starched laundry is not always suitable for dryers a starch leaves behind a coating that oatingand blended fabrics the (Finished in) button repeatedly until the required number of hours is displayed (h=hour). reduces the drying effect. ntainingwool

Mixed Fabrics A mixed load of fabrics made of s Childproof lock: Activate/Deactivate a Start programme, press and hold the  – When washing laundry that is to be tumble-dried afterwards, use the correct amount of f cottonor linen 3. Remove any fluff, (Finished in) button above the display panel for 5 seconds. cotton and synthetic fabrics Programme selector / Off Display panel / Buttons rinse both fluff filters fabric softener as specified in the manufacturer's instructions. Û (Menu) ÖüSpin Speed; ×üAdjust drying level; Õülow heat, žüAmount of steam – With a small load, use the time programme.

Lingerie Very delicate synthetic, cotton or under running water C/board Dry and Depending on the selected programme, it may not be possible to select individual options. c blended fabrics and dry thoroughly. +

Tips for unwrinkle/refresh ,

Hand or machine-washable fabrics Wool in basket Ö]Spin Speed: The spin speed that was used for spinning in the washing machine /93069000812483 *812483* Close the door 4. Fold the fluff filters – Use your dryer to unwrinkle and refresh fabrics. Refer to the table of consumption rates on Page 10 made of wool or containing wool 2 closed, put them a used exclusively to display the anticipated drying time ((Finished in) time) more accurately. a – Unwrinkling cycle to reduce creasing. a Jeans Fabrics made from jeans/denim back together and reinsert them into the appliance. ×cAdjust drying level: The drying result (e.g. C/board Dry) can be increased in three stages (+1 - max. +3); exception: Zeitprogramme (Timer programmes). Default = 0. After one – Refresh cycle to reduce odours in fabrics. Warm time program All types of fabric except for wool programme has been finely adjusted, the setting is retained for the others. Contents Page and silk Õlow heat: Reduced temperature for delicate fabrics ', e.g. polyacrylic, polyamide or Do not use unwrinkle/refresh for the following fabrics: Preparation ...... 2 Cotton, easy-care and blended C/boardDry Extra ʋ Auto on the programme). Multi-layered fabrics require a elastane, with a longer drying time. – Wool, leather, fabrics with metal, wooden or plastic parts. fabric. Fabrics must be suitable for tumble drying  ʋ Control panel ...... 2 fabrics isselected Two-part Remove the laundry and switch off žüAmount of steam: Only for steam programmes. Fine adjustment of the steam can be – Waxed and oiled . a ʋ Drying ...... 3/4 Outdoor Weatherproof and outdoor Select the fluff filter 5 selected: normal, ÷üstrong, øüvery strong. Standard setting: normal. i ʋ Display panel and buttons ...... 5 with a membrane coating and water- Ø 3 the dryer ecoPerfect ¢ To save energy during a prolonged drying time. – Sort the laundry by colour and use the unwrinkle/refresh cycles separately to prevent ʋ Notes on laundry ...... 6 repellent fabrics (Start/Pause) discolouration. speedPerfect i For drying in a shorter time at a higher level of energy consumption. Perfect ʋ Overview of programmes ...... 5 Super 40' Synthetics, cotton or blended fabrics – For best results, take each item out of the machine separately, as soon as the programme Type of fabric Type water-repellentfabrics button Memory 1/2 To save individual programme settings that are used frequently. Use the programme selector to Hard-wearingfabrics, boil-resistant fabrics made o Fabricsmade from synthetic or blendedfabrics Mixedfabrics made cotton of and synthetics Verydelicate synthetic, cotton or blendedfabrics machine-washableHand or woolco or madefabrics of Fabricsmade from jeans/denim All typesof fabric except for wool and silk Cotton,easy-care and blended fabrics Weatherproofand outdoor clothing with membrane a c Synthetics,light cotton or blended fabrics Casualwear made of cotton artificial or fibres Suits,jackets and Easy-carefabrics Hard-wearingfabrics made from cotton ʋ Steam programmes ...... 8/9 Air inlet comes to an end, and hang on a clothes hanger to finish drying. If necessary, pull into ʋ Important information / 4 End of the programme ... select the required programme. Press and hold the Memory 1/2 button for 3 seconds until the shape. speed Consumption rates ...... 10 Steam programmes required programme has been saved. To select the saved programme, briefly press the

Memory 1/2 button. The programme that is called from Memory 1/2 is displayed on the display Environmental protection / Energy-saving tips 8 kg/ 5 kg* 3.5 kg 3.5 kg 2 kg 1 kg 6 kg 2 kg 2 kg 1.5 kg 1.5 kg 1.5 kg 2.5 kg ʋ Normal noises ...... 11 Casual refresh Casual wear made of cotton or ecoPerfect ¢ Energy-saving programme Change the functions in the display using the buttons ? > Interrupt the programme panel. artificial fibres sequence – Before drying, spin the laundry in the washing machine a the higher the spin speed, the ʋ What to do if ... / After-sales service. . . 12 Õ (Drying target) C/board Dry Extra, + C/board Dry, Ô Iron Dry 1. Open the door or select the (Start/Pause) button, ¾ 3 sec (Basic end signal, button signal, auto power-off and Language. Press and simultaneously hold shorter the drying time will be, thus less energy is consumed. Also spin easy-care laundry. ʋ Safety instructions ...... 13 Business refresh Suits, jackets and trousers speedPerfect i Accelerated programme Ø ü settings 3 sec.) both sequence Î (Less Ironing) Anti-crease function can be set up to 120 mins Drying drying cycle is interrupted. – Use the maximum recommended capacity, but do not exceed it Easy-care non-iron Easy-care fabrics ¾ 3 sec (Basic settings 3 sec.) buttons for 3 seconds, in order to access the menu. a Programme overview page 7. (Finished in) Time delay/sChildlock 2. Add or remove laundry and close the door. end signal, button signal: The signal volume level can be selected: off - quiet - medium - loud - Cottons non-iron Hard-wearing fabrics made from Memory 1 Save or call individual 3. If required, select a new programme and additional – Make sure the room is well ventilated during drying. Further information a Page 5. very loud. non-iron cotton } settings Û (Menu) Ö]Spin Speed, ×cAdjust drying level, Õ low heat, ž Amount of steam refresh Memory 2 functions. Select the Ø(Start/Pause) button. The Activate/deactivate by pressing the buttons. – Clean the fluff filter after every drying cycle a Clean the fluff filter, Page 4. non-iron

auto power-off: ¾ 3 sec (Basic settings 3 sec.) refresh ¾ 3 sec end signal, button signal, auto power-off and Language Take care when opening the door. time program (Start/Pause) Start or pause the programme  (Finished in) time is updated after a few minutes. The dryer automatically switches off, depending on your selection, after 15, 30 or 60 minutes. – Keep the supply of cool air unobstructed a Do not cover or block the air inlet.

Øü Dryness levels can be individually selected (Basic settings 3 sec.) Hot steam may escape. The setting is active after Î (Less Ironing) or end of programme. Sortthe laundry according to type textileof and  Reduced loading whenthe option Overview ofProgrammes Overview ofProgrammes Recommendation: Dry separately. Programmes Max. Degree of dryness can be finely adjusted (depending * Language: Select the required language. a a Cotton Easy-Care Mixed Fabrics Wool in basket Jeans Warm Auto Outdoor Super 40' Steam programmes Casual Business Easy-care Cottons 1 2 3 4 5 6 7 Steam programmes Steam programmes Important information... Normal noises What to do if ... Safety instructions Steam programmes for unwrinkling or refreshing Your dryer is designed to be particularly energy efficient. Its technical features include a If you cannot rectify a fault yourself (e.g. by switching the dryer off/on), please contact our after-sales Emergency – Pull the mains plug out of the socket immediately or disconnect the fuse. Before starting a steam programme, fill the refresher tank with distilled water only. refrigeration circuit, which uses energy efficiently, in a similar way to a refrigerator. During drying, the compressor and the pump generate some noise which is entirely normal. service. We will always find an appropriate solution and avoid unnecessary visits by engineers. Trust ONLY use the – in rooms inside the house. Do not use tap water, condensed water or additives. – Your dryer has unwrinkling and refresh programmes that can be used to minimise odours The dryer's heat exchanger is cleaned automatically during drying. the expertise of the manufacturer and this will ensure that the repair will be carried out by trained dryer... – for drying or unwrinkling/refreshing fabrics. service technicians using original spare parts. The contact details of your local after-sales service and creasing in dry fabrics. Steam unwrinkles and refreshes items of clothing. The fluff filters and filter in the condensation container must be cleaned regularly. The dryer must – be used for purposes other than those described above. – The laundry must be sorted according to size, weight, fabric and colour. can be found in the enclosed after-sales service directory: – GB 0844 8928999 (Calls from a BT landline will be charged at up to 3 pence per minute. A call NEVER... – be modified in terms of its technology or properties. Set the programme selector to one of the steam programmes. – Only use the unwrinkling or refresh programmes together for fabrics with the same 1. Never operate the dryer without the fluff filters or the filter in the condensation container. set-up fee of up to 6 pence may apply.) Hazards – The dryer must not be used by children or persons who have not been The selection available is: Casual refresh, Business refresh for refreshing properties. The compressor in the dryer may – IE 01450 2655 (0.03 € per minute at peak. Off peak 0.0088 € per minute.) instructed in its use. and Easy-care non-iron, Cottons non-iron for unwrinkling. – The result of refreshing and unwrinkling may vary depending on the type of fabric, size of occasionally generate a humming noise. When contacting the after-sales service, please specify the product number (E-No.) and production – Do not leave children unsupervised near the dryer. load and programme selected. Fluff filters The volume and pitch of this may vary number (FD) of your appliance (see inside of door). – Keep pets away from the dryer. – During steam generation (required), additional noises may occur. ʑ depending on the selected Switch the dryer off using the programme selector and unplug the mains plug from the socket. – Remove all objects from pockets, and lighters in particular Please empty condensate Empty the condensation container aPage 4. a Risk of explosion. – After unwrinkling or refreshing, all fabrics must be removed immediately and hung crease- During drying, fluff and hair from the laundry is trapped by the fluff filter. A blocked fluff filter programmes and the progress of the free on a hanger or a washing line for 15 minutes. drying. ʠ container is displayed. Press any button. – Do not lean or sit on the door a Risk of tipping. may impair the heat exchange process. Select the Ø (Start/Pause) button again. – Open the door carefully. Hot steam may escape. Fabrics and drum may be 2. Select the Ø (Start/Pause) button. The fluff filters must therefore be cleaned after every drying cycle. Please empty condensate Is the condensation drain installed? aCondensation drain hota Risk of burns. Rinse regularly under running water a Page 4. ʠ container is displayed and the hose blocked a check and clean the hose. Installation – Secure loose leads or hoses, otherwise there is a Risk of tripping. Observe the safety drying cycle is interrupted. Stopper in the condensation container? aseparate – Below 0 °C, there is a possibility of frost damage. instructions on The refresher tank is only to be filled if Refresher-container is empty, Filter in the condensation container Instructions for condensation drain. Mains – Connect the dryer to an AC earthed socket according to specifications, page 13. please re-fill. appears in the display and an audible signal is heard. To do ʑ Is the filter in the condensation container dirty? aClean the Programmes The filter in the condensation container cleans the condensation. This condensation is connection otherwise it cannot be guaranteed that the appliance is completely safe. this: filter in the condensation container a Installation and – The cable cross-section must be sufficient. Please observe the care labels and manufacturer's instructions on the fabrics. required for the automatic cleaning process. The filter should be cleaned regularly under maintenance instructions, Page 3. 3. Completely remove the condensation container. Do not use the unwrinkling or refresh programmes for fabrics made of wool or leather, running water. Empty the condensation container before cleaning the filter a Installation and Please clean lint filter is displayed. Clean the fluff filters a Page 4. – Only use earth-leakage circuit breakers with the following symbol: maintenance instructions, Page 3. ʠ Select the Ø (Start/Pause) button again. – The appliance plug and socket must be compatible. fabrics containing metal or wooden parts or for waxed or oiled jackets. Do not use any dryer – Do not use multiple plugs/connectors and/or extension cables. cleaning sets. The compressor in the dryer is ventilated Refresher-container is empty, Fill it with distilled water a Page 8. Fabrics ʠ please re-fill. is displayed. – Do not touch or hold the appliance plug with wet hands If the filter in the refresher tank is dirty ʑ from time to time, which creates a whirring a Risk of electric shock. Do not dry any fabrics that have come into contact with solvents, oil, wax, grease or paint: sound. Steam programmes do not start. Is the filter in the refresher tank dirty? a Clean the filter in the refresher tank, Installation and maintenance ʠ Clean the filter in the refresher tank a Installation and – Never pull the appliance plug out of the socket by its cable. e.g. hair-styling products, nail varnish remover, stain remover, cleaning solvent, etc. – Do not damage the mains lead a Risk of electric shock. instructions on page 2. Casual refresh Empty all pockets. maintenance instructions, page 2. Operation – Only load the dryer as recommended in the programme descriptions Suitable for refreshing casual wear made of cotton or synthetic fibres. Fabrics must be suit- Do not dry non-breathable fabrics. Water overflows when filling the Remove and clean the filter in the refresher tank able for tumble dryersa Observe the care labels. This programme is exclusively used for ʠ refresher tank. a Installation and maintenance instructions, page 2. (Programmes/fabrics, Page 1 and Programme overview, Page 7). Check the refreshing fabrics; they are not cleaned. Remove the fabrics immediately after the pro- Avoid drying laundry items that produce a lot of fluff. contents before you switch the dryer on. 4. Pour distilled water into the filler opening on the refresher tank Dryer does not start. Has the Ø (Start/Pause)übutton been pressed? Door closed? gramme ends. Programme suitable for one pullover, 2 pairs of trousers or 5 shirts/busi- Woollens should be refreshed or dried using the woollens programme only. ʠ Ambient temperature greater than 5 °C? – Do not use the dryer if the laundry has been in contact with solvents, oil, wax, until Refresher container is ready, please press start. appears in the grease or paint (e.g. hair-styling products, nail varnish remover, stain remover, ness shirts. Creasing occurs despite using the Laundry load exceeded? display and an audible signal is heard. Use the jug that is supplied. cleaning solvent, etc.) a Risk of fire/explosion. Business refresh Consumption rates ʠ steam programmes. Remove articles of clothing immediately after the end of the programme, hang up and pull into shape. – Dust (e.g. coal dust, flour) poses a danger: Do not use the dryer Suitable for refreshing suits, jackets and trousers or fabrics that recommend dry cleaning Residual moisture in the fabrics Energy aRisk of explosion and cannot be washed in the washing machine a Observe the care labels. This pro- Fabrics/programmes Drying time** Water is leaking out. Make sure the dryer is level. – Do not put laundry containing foam material/rubber in the dryer With the recommended load, the after spinning consumption** ʠ gramme is exclusively used for refreshing fabrics; they are not cleaned. Remove the fabrics Drying result was not achieved Warm laundry feels damper than it really is. a elastic material may be destroyed and the dryer may be damaged due to steam programmes use approx. 250 - 300 ml of distilled water. Cottons 8 kg possible deformation of the foam material. immediately after the programme ends. Programme for one suit or 1 to 2 smaller laundry ʠ (laundry too damp). The selected programme does not suit the load. Use another items. The automatic cleaning process causes a – Light things, such as long hair, may be sucked into the air inlet of the dryer +cC/board Dry* 1400rpm 50% 162min 1.44kWh clicking noise. drying programme or, in addition, select the time programme a Page 7. aRisk of injury. 1000rpm 60% 186min 1.71kWh – Switch off the dryer once the programme has ended. Use the « ×üAdjust drying level » option a Page 5. Tumble dryer 5. Completely refit the condensation container. non-iron 800rpm 70% 210min 1.98kWh – Use only distilled water for the unwrinkle/refresh programmes. Do not use any Easy-care Thin layer of limescale on the moisture sensors? Suitable for unwrinkling easy-care fabrics such as shirts/business shirts. The best results are Iron Dry* 1400rpm 50% 118min 1.06kWh condensed water, tap water or additives. Ô Clean the moisture sensors aInstallation and maintenance – The distilled water/condensed water is not drinking water and may be achieved for fabrics that have the manufacturer's label “Non-iron”. The fabrics must be 1000rpm 60% 142min 1.32kWh instructions, Page 2. immediately removed after the end of the programme and hung crease-free to dry on a contaminated with fluff. Programme termination, e.g. condensation container, mains – Do not use the dryer if it is defective or if you suspect that it is. clothes hanger or line for 15 minutes. Programme for up to 5 shirts/business shirts. 800rpm 70% 166min 1.59kWh power supply failure, door open or maximum drying time Defect Easy-Care 3.5 kg reached. Repairs must only be carried out by the after-sales service. Cottons non-iron – Do not connect the dryer if the mains cable is defective. To avoid danger, only Instruction manual en 6. Start the steam programme. Suitable for unwrinkling hard-wearing fabrics made of cotton, such as bed linen, tablecloths +cC/board Dry* 800rpm 40% 51min 0.46kWh ʠ Drying time too long. Clean the fluff filters under running water a Page 4. have the defective mains cable replaced by the after-sales service. or shirts/business shirts. The best results are achieved for fabrics that have the 600rpm 50% 62min 0.55kWh Insufficient supply of air a Ensure that air can circulate. Spare parts – For safety reasons, only use genuine spare parts and accessories. manufacturer's label “Non-iron”. The fabrics must be immediately removed after the end of * Programme setting for testing in accordance with applicable standard EN61121. Air inlet may be obstructed? Clear the inlet a Installation and maintenance instructions, Page 1. Disposal – Dryer: Pull out the appliance plug, then cut off the mains cable from the You must read this instruction manual and the the programme and hung crease-free to dry on a clothes hanger or line for 15 minutes. ** The values may differ from those specified, depending on the type of fabric, composition of laundry to be dried, residual appliance. installation and maintenance instructions before using the dryer. Programme for up to 5 /business shirts or 1 to 2 larger laundry items. The process of pumping the condensation Ambient temperature higher than 35 °C a Ventilate the room. moisture in the fabric and the amount of laundry being loaded. into the condensation container generates Dispose of the appliance at a municipal waste disposal facility. When installing the condensation drain, observe the separate The humidity in the room increases Make sure the room is sufficiently ventilated. – Packaging: Keep all packaging out of reach of babies and children Annual energy pumping noises. Instructions for condensation drain (depending on the model)! Fabrics/programmes Option Drying time ʠ significantly. a Risk of suffocation. consumption Heat exchanger is being rinsed is Not an error. Automatic cleaning of the heat exchanger. Do not – Heat exchangers contain a fluorinated greenhouse gas covered by the Kyoto Cottons 8 kg / 4 kg* ʠ displayed in the display panel. empty the condensation container during the cleaning process. protocol (R407C) a Dispose of this properly. Capacity: 0.315 kg. Power failure. As a result of a power failure, the programme is cancelled. If the – All materials are environmentally sound and can be reused. Dispose of all Caution – risk of scalding! +cC/board Dry ecoPerfect¢*** 146 min / per cycle 213 kWh / per year ʠ laundry is still too damp aSwitch on the appliance and restart materials in an environmentally-responsible manner. *** Programme setting for testing and energy labelling in accordance with Directive 2010/30/EU. the programme. Other intermittent noises and Normal noises a page 11. 8 9 10 11 ʠ vibrations. 12 13 Your dryer Intended use Preparation Installation aInstallation and maintenance instructions, Page 1 a ʑ Congratulations! - You have chosen a modern, high-quality domestic ʋ For domestic use only. Never start the dryer if it is damaged. appliance from Siemens. ʋ Only to be used for drying, refreshing or unwrinkling Inform your after-sales service. a One distinctive feature of the condensation dryer with heat pump and fabrics that have been washed with water. automatic cleaning of the heat exchanger is its low energy a hc consumption. Do not leave children a ( unsupervised near the dryer. Every dryer which leaves our factory is carefully checked to ensure 'c that it functions correctly and is in perfect condition. Keep pets away from the dryer. a )c Should you have any questions, our after-sales service will be happy The dryer can be operated by children 8 years old to help. and older, by persons with reduced physical, a sensory or mental abilities and by persons with a

insufficient experience or knowledge if they are a Environmentally-responsible disposal supervised or have been instructed in its use by Dispose of packaging in an environmentally-responsible manner. a responsible adult. ʑ This appliance is designated according to European directive Õü 2002/96/EC, which governs waste electrical and electronic equipment - WEEE).  The directive provides an EU-wide framework for the return and + recycling of used appliances. Programmes / Fabrics Ô Detailed overview of the programmes and fabrics a Programme overview, Page 7. For further information about our products, accessories, spare parts Î a and services, please visit: www.siemens-home.com. Observe the care instructions on the care label. Dryness level, timer programming and options can be individually selected depending on the selected programme The dryer is switched on and off by pressing the  button in the centre of the a and the progress of the programme. programme selector.  Select the programme by turning the outer ring on the programme selector (the

Cotton Hard-wearing fabrics Ô selector can be turned in both directions). The selected programme is displayed.  a  Easy Care Fabrics made from synthetic or  a blended fabrics  s a  Mixed Fabrics A mixed load of fabrics made of cotton and synthetic fabrics Programme selector / Off Display panel / Buttons Û Öü ×ü Õü žü Lingerie Very delicate synthetic, cotton or c

blended fabrics + Wool in basket Hand or machine-washable fabrics Ö] made of wool or containing wool a  a a Jeans Fabrics made from jeans/denim ×c Warm time program All types of fabric except for wool Contents Page and silk Õ ' ʋ Preparation ...... 2 Auto Cotton, easy-care and blended ʋ  Control panel ...... 2 fabrics žü a ʋ Drying ...... 3/4 Outdoor Weatherproof and outdoor clothing Ø ÷ü øü i ʋ Display panel and buttons ...... 5 with a membrane coating and water- ¢ ʋ Notes on laundry ...... 6 repellent fabrics i ʋ Overview of programmes ...... 5 Super 40' Synthetics, cotton or blended fabrics ʋ Steam programmes ...... 8/9 ʋ Important information / Consumption rates ...... 10 Steam programmes ʋ Normal noises ...... 11 Casual refresh Casual wear made of cotton or ecoPerfect ¢ Energy-saving programme Change the functions in the display using the butto ? > ʋ artificial fibres sequence a What to do if ... / After-sales service. . . 12 Õ (Drying target) C/board Dry Extra, + Ô ¾ ʋ Safety instructions ...... 13 Business refresh Suits, jackets and trousers speedPerfect i Accelerated programme Ø ü Î (Less Ironing) Anti-crease function can be set up to 120 mins Easy-care non-iron Easy-care fabrics sequence ¾ a (Finished in) Time delay/s Cottons non-iron Hard-wearing fabrics made from Memory 1 Save or call individual Û (Menu) Ö]Spin Speed, ×c Õ ž a cotton Memory 2 } settings Ø ¾ a ¾ 3 sec end signal, button signal, auto power-off and Language  a Øü(Start/Pause) Start or pause the programme (Basic settings 3 sec.) Î 

a a 1 2 aInstallation and maintenance instructions, Page 1 Drying Empty the condensation container If the condensation drain is installed, it is not necessary to a ʑ ʋ Never start the dryer if it is damaged. empty the condensation container. separate ʋ Inform your after-sales service. Inspect the dryer Instructions for condensation drain. a Empty the container after each drying cycle, and not during a hc the cycle. a ( Make sure your hands are dry. 7 1. Remove the container, holding it level. 'c Hold the plug only. Connect the 2. Pour out the condensed water. Push the container back a )c mains plug in until it clicks into place. You must also observe the a Installation and maintenance instructions, Page 3. Fascia panel a Sort the laundry Condensation a container with filter Remove all items from pockets. Door Clean the fluff filters ʑ Check for cigarette lighters. Õü The drum must be empty prior to loading. Clean fluff filters reduce energy consumption. See programme overview on page 7.  The fluff filter consists of two parts. + 6 Clean the inner and outer fluff filter Ô a after every drying cycle. Î a 1. Open the door. Remove fluff from the door/door area.  button in the centre of the Open the door/load the laundry/ a 1 2. Pull out the inner  he programme selector (the press the programme selector/ and outer fluff filter ected programme is displayed. and open them out.  a  Ô set the programme  a  s a  3. Remove any fluff, Display panel / Buttons rinse both fluff filters Û Öü ×ü Õü žü under running water c

and dry thoroughly. + Close the door 4. Fold the fluff filters Ö] 2 closed, put them a  a back together and reinsert them into the appliance. ×c a

Õ ' ʋ ʋ  Two-part Remove the laundry and switch off žü a

ʋ i Ø fluff filter 5 ÷ü øü ʋ Select the 3 the dryer ¢ ʋ (Start/Pause) i ʋ button ʋ Air inlet ʋ 4 End of the programme ... ʋ ¢ Change the functions in the display using the buttons ? > Interrupt the programme ʋ a Õ C/board Dry Extra, + C/board Dry, Ô Iron Dry ¾ ʋ i 1. Open the door or select the Ø(Start/Pause)übutton, Î Anti-crease function can be set up to 120 mins Drying drying cycle is interrupted. ¾  Time delay/sChildlock 2. Add or remove laundry and close the door. a 3. If required, select a new programme and additional Û Ö]Spin Speed, ×cAdjust drying level, Õ low heat, ž Amount of steam Further information a Page 5. functions. Select the Ø(Start/Pause) button. The ¾ a Øü ¾ end signal, button signal, auto power-off and Language Take care when opening the door.  (Finished in) time is updated after a few minutes. a Hot steam may escape. Î 

a a 3 4 a Empty the condensation container Display panel and buttons Information on laundry ... ary to ʋ a ʑ Display panel Labelling of fabrics ʋ Please clean lint Clean the fluff filters a Page 4. Follow the manufacturer's care instructions. filter hcSuitable for tumble drying drying cycle, and not during Please empty Empty the condensation container a Page 4 and/or clean the filter in the condensation 7 condensate container a Installation and maintenance instructions, Page 3. ( Dry at normal temperature. container 'cDry at low temperature. k Refresher-container Fill the refresher tank with distilled water for steam programmes a Page 8. )cDo not tumble dry. is empty, please re- a Installation and maintenance Do not tumble-dry the following fabrics: fill. – Non-breathable fabrics (e.g. rubber-coated). Heat exchanger is Automatic cleaning of the heat exchanger. Do not empty the condensation container while this is – Delicate materials (silk, curtains made from synthetic material) a these may crease. a being rinsed displayed. – Oil-stained laundry. ʑ Buttons Drying tips Õü(Drying target) Select the dryness level (e.g. C/board Dry) or the drying time (20 mins up to 3 hrs 30 mins., depending on the model and programme). – To ensure a consistent drying result, sort the laundry by fabric type and drying programme. C/board Dry Extra: For laundry with thick, multi-layered parts. – Always dry very small fabrics (e.g. baby socks) together with + C/board Dry: For single-layered laundry. large items of laundry (e.g. towels). 6 Ô Iron Dry: The condition of the laundry means it is suitable for ironing (iron clothes in order – Close zips, hooks and eyelets, and button up covers. to avoid creases). Tie cloth belts, apron strings, etc. together or use a laundry bag. a Î (Less Ironing) After the programme finishes, the drum moves at regular intervals to prevent creases. The – Do not over-dry easy-care laundry a Risk of creasing. automatic anti-crease function can be set in 30-minute segments up to 120 minutes. The Allow laundry to finish drying in the air. standard setting for each programme is 60 minutes. – Do not iron laundry immediately after drying; fold items up and leave for a while  a (Finished in) When a programme is selected, the anticipated drying time for the maximum load is displayed. residual moisture will then be distributed evenly. While drying, the moisture sensors detect the actual load and correct the programme length. This – Knitted fabrics (e.g. T-shirts, jerseys) often shrink slightly the first time they are tumble-dried. is shown in the display by jumps in the (Finished in) time. aDo not use the  C/board Dry Extra programme. Ô The (Finished in) time can be delayed in one-hour steps, up to a maximum of 24 hours. Press – Starched laundry is not always suitable for dryers a starch leaves behind a coating that the (Finished in) button repeatedly until the required number of hours is displayed (h=hour). reduces the drying effect. s a  Childproof lock: Activate/Deactivate Start programme, press and hold the – When washing laundry that is to be tumble-dried afterwards, use the correct amount of (Finished in) button above the display panel for 5 seconds. fabric softener as specified in the manufacturer's instructions. Û Öü ×ü Õü žü (Menu) Spin Speed; Adjust drying level; low heat, Amount of steam – With a small load, use the time programme. Depending on the selected programme, it may not be possible to select individual options. c Tips for unwrinkle/refresh + Ö]Spin Speed: The spin speed that was used for spinning in the washing machine a used exclusively to display the anticipated drying time ((Finished in) time) more accurately. – Use your dryer to unwrinkle and refresh fabrics. a – Unwrinkling cycle to reduce creasing. a ×cAdjust drying level: The drying result (e.g. C/board Dry) can be increased in three stages (+1 - max. +3); exception: Zeitprogramme (Timer programmes). Default = 0. After one – Refresh cycle to reduce odours in fabrics. programme has been finely adjusted, the setting is retained for the others. Õ ' Do not use unwrinkle/refresh for the following fabrics: ʋ low heat: Reduced temperature for delicate fabrics , e.g. polyacrylic, polyamide or elastane, with a longer drying time. – Wool, leather, fabrics with metal, wooden or plastic parts. ʋ  Remove the laundry and switch off žüAmount of steam: Only for steam programmes. Fine adjustment of the steam can be – Waxed and oiled jackets. a

ʋ i Ø selected: normal, ÷üstrong, øüvery strong. Standard setting: normal. ʋ ecoPerfect ¢ To save energy during a prolonged drying time. – Sort the laundry by colour and use the unwrinkle/refresh cycles separately to prevent ʋ discolouration. i ʋ speedPerfect For drying in a shorter time at a higher level of energy consumption. – For best results, take each item out of the machine separately, as soon as the programme ʋ Memory 1/2 To save individual programme settings that are used frequently. Use the programme selector to comes to an end, and hang on a clothes hanger to finish drying. If necessary, pull into ʋ select the required programme. Press and hold the Memory 1/2 button for 3 seconds until the shape. required programme has been saved. To select the saved programme, briefly press the ʋ ¢ ? > Memory 1/2 button. The programme that is called from Memory 1/2 is displayed on the display Environmental protection / Energy-saving tips panel. ʋ Õ – Before drying, spin the laundry in the washing machine a the higher the spin speed, the  + Ô ¾ 3 sec (Basic end signal, button signal, auto power-off and Language. Press and simultaneously hold ʋ i Ø ü shorter the drying time will be, thus less energy is consumed. Also spin easy-care laundry. Î settings 3 sec.) both ¾ – Use the maximum recommended capacity, but do not exceed it 3 sec (Basic settings 3 sec.) buttons for 3 seconds, in order to access the menu. a Programme overview page 7.  s end signal, button signal: The signal volume level can be selected: off - quiet - medium - loud - – Make sure the room is well ventilated during drying. Û Ö] ×c Õ ž a very loud. Ø auto power-off: Activate/deactivate by pressing the ¾ 3 sec (Basic settings 3 sec.) buttons. – Clean the fluff filter after every drying cycle a Clean the fluff filter, Page 4. Øü ¾  The dryer automatically switches off, depending on your selection, after 15, 30 or 60 minutes. – Keep the supply of cool air unobstructed a Do not cover or block the air inlet. The setting is active after Î (Less Ironing) or end of programme. 

Language: Select the required language. a a 5 6 a

ʋ a ʑ ʋ a fabrics.of WT48Y890DN he he programme on the othing. a hc s. 7 a ( vidual items of 'c . a )c a see Basketthe for woollens and the notes Pageon 6. a Carl-WeryStr. 34 a ʑ Õü SiemensElectrogeräte GmbH 81739München/Deutschland  + 6 Ô a Î a longerdrying time than single-layered items of cl Options and notes description. Use with separate basket only  For pre-dried, multi-layered fabrics or small, indi laundry. Also for subsequent drying. Automatic detection of residual moisture and drying Particularly gentle. Easy-to-dry textiles. For refreshing fabrics only. Observe carethe label Only for unwrinklng fabrics.of Best results can be expected "Non-iron"if appears manufacturer's label; remove the items as soon as t ends.  a Iron Dry (depending on the model andprogramme)

 a  Ô  a oatingand

 ntainingwool s a  f f cottonor linen

Û Öü ×ü Õü žü C/board Dry and c + ,

Ö] 9306 /93069000812483 *812483* a  Refer to the table of consumption rates on Page 10 a ×c a

Õ ' ʋ C/boardDry Extra on the programme). Multi-layered fabrics require a fabric. Fabrics must be suitable for tumble drying  ʋ isselected žü a ʋ Ø ÷ü øü i ʋ ¢ ʋ ʋ i Perfect Type of fabric Type water-repellentfabrics ʋ Hard-wearingfabrics, boil-resistant fabrics made o Fabricsmade from synthetic or blendedfabrics Mixedfabrics made cotton of and synthetics Verydelicate synthetic, cotton or blendedfabrics machine-washableHand or woolco or madefabrics of Fabricsmade from jeans/denim All typesof fabric except for wool and silk Cotton,easy-care and blended fabrics Weatherproofand outdoor clothing with membrane a c Synthetics,light cotton or blended fabrics Casualwear made of cotton artificial or fibres Suits,jackets and trousers Easy-carefabrics Hard-wearingfabrics made from cotton ʋ speed

ʋ ¢ ? > 8 kg/ 5 kg* 3.5 kg 3.5 kg 2 kg 1 kg 6 kg 2 kg 2 kg 1.5 kg 1.5 kg 1.5 kg 2.5 kg ʋ a Õ  + Ô ¾ ʋ i Ø ü Î ¾  s a a non-iron

Û Ö] ×c Õ ž refresh

Ø ¾ a non-iron refresh Øü ¾  a time program Dryness levels can be individually selected Î Sortthe laundry according to type textileof and  Reduced loading whenthe option Overview ofProgrammes Overview ofProgrammes Recommendation: Dry separately. Programmes Max. Degree of dryness can be finely adjusted (depending * a a Cotton Easy-Care Mixed Fabrics Lingerie Wool in basket Jeans Warm Auto Outdoor Super 40' Steam programmes Casual Business Easy-care Cottons 7 Steam programmes Steam programmes Steam programmes for unwrinkling or refreshing Before starting a steam programme, fill the refresher tank with distilled water only. Do not use tap water, condensed water or additives. – Your dryer has unwrinkling and refresh programmes that can be used to minimise odours and creasing in dry fabrics. Steam unwrinkles and refreshes items of clothing. – The laundry must be sorted according to size, weight, fabric and colour. 1. Set the programme selector to one of the steam programmes. – Only use the unwrinkling or refresh programmes together for fabrics with the same The selection available is: Casual refresh, Business refresh for refreshing properties. and Easy-care non-iron, Cottons non-iron for unwrinkling. – The result of refreshing and unwrinkling may vary depending on the type of fabric, size of load and programme selected. – During steam generation (required), additional noises may occur. ʑ – After unwrinkling or refreshing, all fabrics must be removed immediately and hung crease- a a ʠ a free on a hanger or a washing line for 15 minutes. Ø 2. Select the Ø (Start/Pause) button. a a a ʠ a a The refresher tank is only to be filled if Refresher-container is empty, ʑ please re-fill. appears in the display and an audible signal is heard. To do Programmes a this: a Please observe the care labels and manufacturer's instructions on the fabrics. a 3. Completely remove the condensation container. Do not use the unwrinkling or refresh programmes for fabrics made of wool or leather, a ʠ Ø fabrics containing metal or wooden parts or for waxed or oiled jackets. Do not use any dryer cleaning sets. ʑ ʠ a If the filter in the refresher tank is dirty a a Clean the filter in the refresher tank, Installation and maintenance ʠ a a instructions on page 2. Casual refresh Suitable for refreshing casual wear made of cotton or synthetic fibres. Fabrics must be suit- able for tumble dryersa Observe the care labels. This programme is exclusively used for ʠ a refreshing fabrics; they are not cleaned. Remove the fabrics immediately after the pro- Ø ü 4. Pour distilled water into the filler opening on the refresher tank gramme ends. Programme suitable for one pullover, 2 pairs of trousers or 5 shirts/busi- ʠ until Refresher container is ready, please press start. appears in the ness shirts. display and an audible signal is heard. Use the jug that is supplied. ʠ a Business refresh Suitable for refreshing suits, jackets and trousers or fabrics that recommend dry cleaning a and cannot be washed in the washing machine a Observe the care labels. This pro- ʠ With the recommended load, the gramme is exclusively used for refreshing fabrics; they are not cleaned. Remove the fabrics a steam programmes use approx. 250 - 300 ml of distilled water. immediately after the programme ends. Programme for one suit or 1 to 2 smaller laundry ʠ items. +c a a ×ü a 5. Completely refit the condensation container. Easy-care non-iron Suitable for unwrinkling easy-care fabrics such as shirts/business shirts. The best results are Ô a achieved for fabrics that have the manufacturer's label “Non-iron”. The fabrics must be immediately removed after the end of the programme and hung crease-free to dry on a clothes hanger or line for 15 minutes. Programme for up to 5 shirts/business shirts. Cottons non-iron +c a 6. Start the steam programme. Suitable for unwrinkling hard-wearing fabrics made of cotton, such as bed linen, tablecloths ʠ or shirts/business shirts. The best results are achieved for fabrics that have the a manufacturer's label “Non-iron”. The fabrics must be immediately removed after the end of a  the programme and hung crease-free to dry on a clothes hanger or line for 15 minutes. Programme for up to 5 shirt/business shirts or 1 to 2 larger laundry items. a ʠ a ʠ a

+c ¢ ʠ a

a 8 9 ʠ Important information... Normal noises Your dryer is designed to be particularly energy efficient. Its technical features include a refrigeration circuit, which uses energy efficiently, in a similar way to a refrigerator. During drying, the compressor and the pump generate some noise which is entirely normal. The dryer's heat exchanger is cleaned automatically during drying. The fluff filters and filter in the condensation container must be cleaned regularly.

Never operate the dryer without the fluff filters or the filter in the condensation container. The compressor in the dryer may occasionally generate a humming noise. The volume and pitch of this may vary ʑ Fluff filters depending on the selected programmes and the progress of the a a During drying, fluff and hair from the laundry is trapped by the fluff filter. A blocked fluff filter ʠ a may impair the heat exchange process. drying. Ø Ø The fluff filters must therefore be cleaned after every drying cycle. a a Rinse regularly under running water a Page 4. ʠ a a ʑ Filter in the condensation container a The filter in the condensation container cleans the condensation. This condensation is a required for the automatic cleaning process. The filter should be cleaned regularly under running water. Empty the condensation container before cleaning the filter a Installation and ʠ a maintenance instructions, Page 3. Ø The compressor in the dryer is ventilated ʠ a ʑ Fabrics from time to time, which creates a whirring a Do not dry any fabrics that have come into contact with solvents, oil, wax, grease or paint: sound. a ʠ a e.g. hair-styling products, nail varnish remover, stain remover, cleaning solvent, etc. a Empty all pockets. a Do not dry non-breathable fabrics. ʠ a Avoid drying laundry items that produce a lot of fluff. Ø ü Woollens should be refreshed or dried using the woollens programme only. ʠ Consumption rates ʠ a a a Fabrics/programmes Residual moisture in the fabrics Drying time** Energy ʠ after spinning consumption** a Cottons 8 kg ʠ The automatic cleaning process causes a +cC/board Dry* 1400rpm 50% 162min 1.44kWh clicking noise. a 1000rpm 60% 186min 1.71kWh a ×ü a 800rpm 70% 210min 1.98kWh Ô Iron Dry* 1400rpm 50% 118min 1.06kWh a 1000rpm 60% 142min 1.32kWh 800rpm 70% 166min 1.59kWh Easy-Care 3.5 kg +cC/board Dry* 800rpm 40% 51min 0.46kWh ʠ a 600rpm 50% 62min 0.55kWh a a  * Programme setting for testing in accordance with applicable standard EN61121. ** The values may differ from those specified, depending on the type of fabric, composition of laundry to be dried, residual The process of pumping the condensation a moisture in the fabric and the amount of laundry being loaded. into the condensation container generates Annual energy pumping noises. ʠ Fabrics/programmes Option Drying time a consumption ʠ Cottons 8 kg / 4 kg* a +cC/board Dry ecoPerfect¢*** 146 min / per cycle 213 kWh / per year ʠ a *** Programme setting for testing and energy labelling in accordance with Directive 2010/30/EU. ʠ a 10 11 What to do if ... Safety instructions If you cannot rectify a fault yourself (e.g. by switching the dryer off/on), please contact our after-sales Emergency – Pull the mains plug out of the socket immediately or disconnect the fuse. service. We will always find an appropriate solution and avoid unnecessary visits by engineers. Trust ONLY use the – in rooms inside the house. the expertise of the manufacturer and this will ensure that the repair will be carried out by trained dryer... – for drying or unwrinkling/refreshing fabrics. service technicians using original spare parts. The contact details of your local after-sales service can be found in the enclosed after-sales service directory: The dryer must – be used for purposes other than those described above. – GB 0844 8928999 (Calls from a BT landline will be charged at up to 3 pence per minute. A call NEVER... – be modified in terms of its technology or properties. set-up fee of up to 6 pence may apply.) Hazards – The dryer must not be used by children or persons who have not been – IE 01450 2655 (0.03 € per minute at peak. Off peak 0.0088 € per minute.) instructed in its use. When contacting the after-sales service, please specify the product number (E-No.) and production – Do not leave children unsupervised near the dryer. number (FD) of your appliance (see inside of door). – Keep pets away from the dryer. ʑ Switch the dryer off using the programme selector and unplug the mains plug from the socket. – Remove all objects from pockets, and lighters in particular ʠ Please empty condensate Empty the condensation container aPage 4. a Risk of explosion. container is displayed. Press any button. – Do not lean or sit on the door a Risk of tipping. Select the Ø (Start/Pause) button again. Ø – Open the door carefully. Hot steam may escape. Fabrics and drum may be Please empty condensate Is the condensation drain installed? aCondensation drain hota Risk of burns. a ʠ container is displayed and the hose blocked a check and clean the hose. Installation – Secure loose leads or hoses, otherwise there is a Risk of tripping. drying cycle is interrupted. Stopper in the condensation container? aseparate – Below 0 °C, there is a possibility of frost damage. ʑ Instructions for condensation drain. a Mains – Connect the dryer to an AC earthed socket according to specifications, Is the filter in the condensation container dirty? Clean the otherwise it cannot be guaranteed that the appliance is completely safe. filter in the condensation container a Installation and connection maintenance instructions, Page 3. – The cable cross-section must be sufficient. a ʠ Please clean lint filter is displayed. Clean the fluff filters a Page 4. – Only use earth-leakage circuit breakers with the following symbol: Select the Ø (Start/Pause) button again. – The appliance plug and socket must be compatible. ʠ Refresher-container is empty, Fill it with distilled water a Page 8. – Do not use multiple plugs/connectors and/or extension cables. is displayed. – Do not touch or hold the appliance plug with wet hands ʑ please re-fill. a Steam programmes do not start. Is the filter in the refresher tank dirty? Risk of electric shock. a ʠ a – Never pull the appliance plug out of the socket by its cable. Clean the filter in the refresher tank Installation and a maintenance instructions, page 2. – Do not damage the mains lead Risk of electric shock. ʠ Water overflows when filling the Remove and clean the filter in the refresher tank Operation – Only load the dryer as recommended in the programme descriptions a refresher tank. a Installation and maintenance instructions, page 2. (Programmes/fabrics, Page 1 and Programme overview, Page 7). Check the contents before you switch the dryer on. ʠ Dryer does not start. Has the Ø (Start/Pause)übutton been pressed? Door closed? Ambient temperature greater than 5 °C? – Do not use the dryer if the laundry has been in contact with solvents, oil, wax, grease or paint (e.g. hair-styling products, nail varnish remover, stain remover, ʠ Creasing occurs despite using the Laundry load exceeded? cleaning solvent, etc.) a steam programmes. Remove articles of clothing immediately after the end of the Risk of fire/explosion. programme, hang up and pull into shape. – Dust (e.g. coal dust, flour) poses a danger: Do not use the dryer aRisk of explosion a ʠ Water is leaking out. Make sure the dryer is level. – Do not put laundry containing foam material/rubber in the dryer a Drying result was not achieved Warm laundry feels damper than it really is. elastic material may be destroyed and the dryer may be damaged due to ʠ possible deformation of the foam material. (laundry too damp). The selected programme does not suit the load. Use another +c – Light things, such as long hair, may be sucked into the air inlet of the dryer drying programme or, in addition, select the time programme a a Page 7. Risk of injury. ×ü a – Switch off the dryer once the programme has ended. Use the « Adjust drying level » option Page 5. – Use only distilled water for the unwrinkle/refresh programmes. Do not use any Ô Thin layer of limescale on the moisture sensors? condensed water, tap water or additives. Clean the moisture sensors aInstallation and maintenance – The distilled water/condensed water is not drinking water and may be instructions, Page 2. contaminated with fluff. Programme termination, e.g. condensation container, mains – Do not use the dryer if it is defective or if you suspect that it is. power supply failure, door open or maximum drying time Defect reached. Repairs must only be carried out by the after-sales service. a – Do not connect the dryer if the mains cable is defective. To avoid danger, only +c ʠ Drying time too long. Clean the fluff filters under running water Page 4. have the defective mains cable replaced by the after-sales service. a Insufficient supply of air Ensure that air can circulate. Spare parts – For safety reasons, only use genuine spare parts and accessories. Air inlet may be obstructed? Clear the inlet a Installation and maintenance instructions, Page 1. Disposal – Dryer: Pull out the appliance plug, then cut off the mains cable from the a appliance. Ambient temperature higher than 35 °C Ventilate the room. Dispose of the appliance at a municipal waste disposal facility. ʠ The humidity in the room increases Make sure the room is sufficiently ventilated. – Packaging: Keep all packaging out of reach of babies and children significantly. a Risk of suffocation. ʠ Heat exchanger is being rinsed is Not an error. Automatic cleaning of the heat exchanger. Do not – Heat exchangers contain a fluorinated greenhouse gas covered by the Kyoto displayed in the display panel. empty the condensation container during the cleaning process. protocol (R407C) a Dispose of this properly. Capacity: 0.315 kg. +c ¢ ʠ Power failure. As a result of a power failure, the programme is cancelled. If the – All materials are environmentally sound and can be reused. Dispose of all laundry is still too damp aSwitch on the appliance and restart materials in an environmentally-responsible manner. the programme. ʠ Other intermittent noises and Normal noises a page 11. vibrations. 12 13 ʑ a a ʠ a Ø Ø a a a ʠ a a Observe the safety instructions on ʑ page 13. a a a a ʠ Ø ʠ a ʑ a a ʠ a a a ʠ a ʠ Ø ü ʠ a a a ʠ ʠ a +c a a ×ü a Tumble dryer

Ô a

Instruction manual en +c ʠ a a a  You must read this instruction manual and the a installation and maintenance instructions before using the dryer. When installing the condensation drain, observe the separate ʠ Instructions for condensation drain (depending on the model)! a ʠ a Caution – risk of scalding! +c ¢ ʠ a ʠ a