sign in sign up
<<
Home , Junk rig, Yacht

The Rig

(the westernised version, as developed by Blondie Hasler in the UK, and by Tom Colvin in the US)

The two pioneers who did most to bring the to the attention of the public. Blondie sailed “Jester” in the first single-handed transatlantic race, and Tom has designed a range of functional junk rigged and cargo vessels.

1 One of the best known of junk rigged , thanks to Annie Hill’s book “Voyaging on a small income”

She has sailed more than 100,000 miles in the North and South Atlantic, from Greenland to the South Orkney Islands. She is one of Jay Benford’s sailing dory designs. Everything was home-made, on a very limited budget “Badger”,in Greenland

2 What is it?

A rig derived from the rigs used in , and adapted for use on modern yachts

It may have a stayed or un-stayed (s), but an unstayed mast is usually preferred

It always has stiff battens, most of which are controlled by a sheeting system which permits control over and shape.

Stresses are widely distributed, and are much lower than in the bermudan rig

It usually has a at an angle of between 20 and 70 degrees to the horizontal

3 What does it do well? Reefing (on any point of Gybing is easy, quiet and sail) is a simple matter of safe No dramas easing the and trimming the and the When the sheet is eased, other control lines 15 seconds for the sail is quiet and the first reef docile No flogging Furling (on any ) is a simple matter of Speed can easily be letting go the halyard, controlled by easing sheets when the sail is gathered and/or reefing, when into the topping lifts Failsafe approaching harbour No dramas, again

Tacking is a simple matter Performance downwind is of putting the helm over - superior to bermudan rig no sheets to handle No flogging Less heeling, easier motion

4 What does it do badly? A flat junk sail does Nothing else not have the drive of a cambered sail, So why doesn’t the modern yachtsman use the junk rig, when he and performance to seems to prefer motoring to windward? Innate windward in light conservatism, and an unwillingness to stand out breezes is poor, when from the crowd, perhaps? compared to that of a bermudan with a

5 How can the windward performance be improved?

By adding camber - obvious, really

In strong and variable winds, a junk rigged can make safely and comfortably to windward when a bermudan rigged yacht is finding the going too difficult

6 The fiendishly-clever Chinese way of adding camber, that Blondie Hasler somewhat overlooked when he designed his rigs

A fanned sail develops camber in its upper part by twisting, even if it is cut flat

7 Hinges have been used successfully, but most ocean sailors don’t favour them

Hinged battens have been used, but integrity is compromised, and the standard of design and manufacture must be high

8 The preferred approach is to build camber into most of the panels of the sail, using a variety of sailmaking techniques - broad seam, shelf foot, tucks etc

9 “Tystie” has covered nearly 50,000 miles with these . The first (GRP,) battens were replaced a year ago, in , with lighter, better shaped ones in aluminium alloy

Best, but at a high cost, is the “soft wing-sail”, enclosing the mast. The after part of the sail has stiff battens, but the forward part is doubled around wishbones, enclosing the mast

10 There are many different planforms and varieties of junk rig

From left to right: 1.A Wharram with a wing sail on each hull 2.A “split rig”, with cambered “” and 3.A commercially available sail shape

11 “China Moon”, in the Tamar River

Junk rig on a catamaran- one mast in each hull

12 Aren’t all the control lines very complicated?

Not as complicated as those Batten parrels keep the in a bermudan rig - just battens close to the mast different Topping lifts support the A halyard, usually with aft end of the sail bundle several parts because the sail bundle is heavier Another lift supports the forward end of the sail A sheet, which also acts as bundle reefing lines There may be more luff A yard parrel keeps the yard parrels close to the mast There may be batten A luff parrel peaks up the yard and shapes the sail

13 A fanned sail One of the modern sail shapes, with the major lines shown

A Raven 26’ , “Fantail”, now being rigged in New Ze aland

14 Is an un-stayed mast safe? Safer than a stayed A stayed mast relies mast on every component of its complex If it is designed triangulated staying right, and built system being in place right, it is very - if one little pin difficult to get an is lost, the whole un-stayed mast to rig might be lost fail It takes a load in excess of that for which the rig was designed - a 360 degree rollover will do it often fail through fatigue

15 Isn’t an unstayed mast very heavy? The un-stayed mast However, when the itself is heavier weight of all the than a bermudan standing is mast, because it added to the weight must be designed to of a bermudan mast, resist bending loads the un-stayed mast usually shows a The bermudan mast is weight saving lighter, because it only has to resist compressive loads

16 Can I make a junk rig for my boat? There is nothing that Sails can be made a backyard handyman from polyester cannot make - unlike , but since bermudan rig the stresses are lower than in Spars can be of wood bermudan rig, a wider or aluminium alloy range of fabrics is tube suitable - making home sailmaking If you made it, you easier can also mend it in remote places Try a rig first 17 Where can I find out more? The standard book is designing and “Practical Junk Rig”, building a junk rig by Blondie Hasler & Jock McCleod. We have The Junk Rig made advances in Association has a several areas since website at it was published in www.junkrigassociation.org 1988, but up to the with a great deal of stage of development useful knowledge, and that they reached, it fora to talk with cannot be faulted. It fellow enthusiasts is an essential reference when

18