Nr. Standard reference Title Information technology — Digitally recorded media for information 1 ISO/IEC FDIS 30193 interchange and storage — 120 mm Triple Layer (100,0 Gbytes per disk) BD Rewritable disk Information technology — Multimedia application format (MPEG-A) — 2 ISO/IEC FDIS 23000-19 Part 19: Common media application format (CMAF) for segmented media Fasteners — Mechanical properties of corrosion-resistant stainless 3 ISO/FDIS 3506-1 steel fasteners — Part 1: Bolts, screws and studs with specified grades and property classes Fasteners — Mechanical properties of corrosion-resistant stainless 4 ISO/FDIS 3506-2 steel fasteners — Part 2: Nuts with specified grades and property classes Fasteners — Mechanical properties of corrosion-resistant stainless 5 ISO/FDIS 3506-6 steel fasteners — Part 6: General rules for the selection of stainless steels and nickel alloys for fasteners Fire protection — Automatic sprinkler systems — Part 7: Requirements 6 ISO/FDIS 6182-7 and test methods for early suppression fast response (ESFR) sprinklers Wheat flour and durum wheat semolina — Determination of impurities 7 ISO/FDIS 11050 of animal origin 8 ISO/FDIS 20771 Legal translation — Requirements Test conditions for numerically controlled turning machines and turning 9 ISO/FDIS 13041-2.2 centres — Part 2: Geometric tests for machines with a vertical workholding spindle Plastics — Carbon and environmental footprint of biobased plastics — 10 ISO/FDIS 22526-2 Part 2: Material carbon footprint, amount (mass) of CO2 removed from the air and incorporated into polymer molecule 11 ISO/FDIS 8659 Thermoplastics valves — Fatigue strength — Test method Implants for surgery — Active implantable medical devices — Part 5: 12 ISO/FDIS 14708-5 Circulatory support devices 13 ISO/FDIS 10018 Quality management — Guidelines for people engagement Fine ceramics (advanced ceramics, advanced technical ceramics) — 14 ISO/FDIS 21712 Test method for flexural bond strength of ceramics Health informatics — Device interoperability — Part 10101: Point-of- 15 ISO/IEEE FDIS 11073-10101 care medical device communication — Nomenclature 16 ISO/FDIS 22483 Tourism and related services — Hotels — Service requirements Extenders — Specifications and methods of test — Part 1: Introduction 17 ISO/FDIS 3262-1 and general test methods Leather — Chemical tests — Quantitative analysis of tanning agents by 18 ISO/FDIS 14088 filter method 19 ISO/FDIS 17131 Leather — Identification of leather with microscopy Information technology — Fibre channel — Part 226: Single-byte 20 ISO/IEC 14165-226:2020 command code sets mapping protocol - 6 (FC-SB-6) Information technology — Fibre channel — Part 246: Backbone — 6 21 ISO/IEC 14165-246:2019 (FC-BB-6) Information technology — IT asset management — Part 8: Guidelines 22 ISO/IEC 19770-8:2020 for mapping of industry practices to/from the ISO/IEC 19770 family of standards 23 ISO 15241:2012/Amd 1:2020 Rolling bearings — Symbols for physical quantities — Amendment 1 24 ISO 21993:2020 Paper and pulp — Deinkability test for printed paper products Ships and marine technology — Cutter suction dredger supervisory and 25 ISO 20661:2020 control systems Ships and marine technology — Hopper dredger supervisory and 26 ISO 20662:2020 control systems Ships and marine technology — Grab dredger supervisory and control 27 ISO 20663:2020 systems Technical product documentation (TPD) — Technical drawings for 28 ISO 6414:2020 glassware Air cargo equipment — Restraint straps — Part 2: Utilization 29 ISO 16049-2:2020 requirements and recommendations and lashing calculations Space environment (natural and artificial) — Operational estimation of 30 ISO/TR 23989:2020 the solar wind energy input into the Earth's magnetosphere by means of the ground-based magnetic polar cap (PC) index 31 ISO 12353-1:2020 Road vehicles — Traffic accident analysis — Part 1: Vocabulary Road vehicles — Human performance and state in the context of 32 ISO/TR 21959-1:2020 automated driving — Part 1: Common underlying concepts 33 ISO 5681:2020 Equipment for crop protection — Vocabulary Crop protection equipment — Reciprocating positive displacement 34 ISO 12809:2020 pumps and centrifugal pumps — Test method 35 ISO 13320:2020 Particle size analysis — Laser diffraction methods Measurement of fluid flow in closed conduits — Ultrasonic meters for 36 ISO 17089-1:2019 gas — Part 1: Meters for custody transfer and allocation measurement 37 ISO 11746:2020 Rice — Determination of biometric characteristics of kernels Milk — Bacterial count — Protocol for the evaluation of alternative 38 ISO 16297:2020 methods Milk and milk products — Guidelines for the application of in-line and on- 39 ISO 23291:2020 line infrared spectrometry 40 ISO 15184:2020 Paints and varnishes — Determination of film hardness by pencil test Paints and varnishes — On-site test methods on quality assessment for 41 ISO 23169:2020 interior wall coatings Textiles — Determination of the total heat transfer through textiles in 42 ISO 20852:2020 simulated environments Imaging materials — Photographic reflection prints — Methods for 43 ISO 18937:2020 measuring indoor light stability Acoustics — Characterization of sources of structure-borne sound and 44 ISO 20270:2019 vibration — Indirect measurement of blocked forces Rubber hoses and hose assemblies for liquefied petroleum gas in motor 45 ISO 8789:2020 vehicles — Specification Plastics — Polyetheretherketone (PEEK) moulding and extrusion 46 ISO 23153-2:2020 materials — Part 2: Preparation of test specimens and determination of properties Plastics — Carbon and environmental footprint of biobased plastics — 47 ISO 22526-1:2020 Part 1: General principles Determination of the resistance to cryogenic spill of insulation materials 48 ISO 20088-2:2020 — Part 2: Vapour exposure 49 ISO 1920-4:2020 Testing of concrete — Part 4: Strength of hardened concrete Measurement of radioactivity in the environment — Air: radon-222 — 50 ISO 11665-4:2020 Part 4: Integrated measurement method for determining average activity concentration using passive sampling and delayed analysis Nuclear criticality safety — Solid waste excluding irradiated and non- 51 ISO 22946:2020 irradiated nuclear fuel Eye and face protection — Test methods — Part 3: Physical and 52 ISO 18526-3:2020 mechanical properties Respiratory protective devices — Human factors — Part 7: Hearing and 53 ISO/TS 16976-7:2020 speech 54 ISO 668:2020 Series 1 freight containers — Classification, dimensions and ratings 55 ISO 1609:2020 Vacuum technology — Dimensions of non-knife edge flanges Vacuum technology — Mounting dimensions of pipeline fittings — Part 56 ISO 9803-1:2020 1: Non knife-edge flange type Vacuum technology — Mounting dimensions of pipeline fittings — Part 57 ISO 9803-2:2020 2: Knife-edge flange type Vacuum technology — Right-angle valve — Dimensions and interfaces 58 ISO 21358:2020 for pneumatic actuator Non-invasive sphygmomanometers — Part 2: Clinical investigation of 59 ISO 81060-2:2018/Amd 1:2020 intermittent automated measurement type — Amendment 1 Tobacco and tobacco products — Determination of nicotine purity — 60 ISO 13276:2020 Gravimetric method using tungstosilicic acid 61 ISO 4874:2020 Tobacco — Sampling of batches of raw material — General principles 62 ISO 5598:2020 Fluid power systems and components — Vocabulary 63 ISO 14743:2020 Pneumatic fluid power — Push-in connectors for thermoplastic tubes Non-destructive testing — Standard test method for determining 64 ISO 21432:2019 residual stresses by neutron diffraction 65 ISO 15727:2020 UV-C devices — Measurement of the output of a UV-C lamp Graphical symbols — Safety colours and safety signs — Registered 66 ISO 7010:2019/Amd 1:2020 safety signs — Amendment 1 Implants for surgery — Wear of total knee-joint prostheses — Part 1: Loading and displacement parameters for wear-testing machines with 67 ISO 14243-1:2009/Amd 1:2020 load control and corresponding environmental conditions for test — Amendment 1 Implants for surgery — Wear of total knee-joint prostheses — Part 3: Loading and displacement parameters for wear-testing machines with 68 ISO 14243-3:2014/Amd 1:2020 displacement control and corresponding environmental conditions for test — Amendment 1 69 ISO 22109:2020 Industrial valves — Gearbox for valves 70 ISO 22153:2020 Electric actuators for industrial valves — General requirements Corrosion of metals and alloys — Classification of low corrosivity of 71 ISO 11844-3:2020 indoor atmospheres — Part 3: Measurement of environmental parameters affecting indoor corrosivity Optics and photonics — Optical transfer function — Application — Part 72 ISO 9336-3:2020 3: Telescopes Intelligent transport systems — Service architecture of probe vehicle 73 ISO 19414:2020 systems Fine ceramics (advanced ceramics, advanced technical ceramics) — Determination of bacterial reduction rate by semiconducting 74 ISO 22551:2020 photocatalytic materials under indoor lighting environment — Semi-dry method for estimating antibacterial activity on the actual environmental bacteria contamination surface Fine ceramics (advanced ceramics, advanced technical ceramics) — 75 ISO 23114:2020 Test method for determining bonding strength of ceramic coatings Geographic information — Geography Markup Language (GML) — Part 76 ISO 19136-1:2020 1: Fundamentals Health informatics — Categorial structure for Chinese materia medica 77 ISO/TS 23303:2020 products manufacturing process Physical and mechanical properties of wood — Test methods for small 78 ISO 13061-5:2020 clear wood specimens — Part 5: Determination of strength in compression perpendicular to grain Traditional Chinese medicine — General requirements of electric radial 79 ISO 18615:2020 pulse tonometric devices 80 ISO 22988:2020 Traditional Chinese medicine — Astragalus mongholicus root Framework for integration and operation of smart community infrastructures — Part 1: Recommendations for considering 81 ISO 37155-1:2020 opportunities and challenges from interactions in smart community infrastructures from relevant aspects through the life cycle Leather — Determination of abrasion resistance — Part 1: Taber® 82 ISO 17076-1:2020 method Manned submersibles — Breathing air supply and CO2 adsorption 83 ISO 22252:2020 systems — Performance requirements and recommendations 84 ISO 11971:2020 Steel and iron castings — Visual testing of surface quality Air cargo equipment — Restraint straps — Part 1: Design criteria and 85 ISO 16049-1:2020 testing methods Space systems — Evaluation of radiation effects on Commercial-Off- 86 ISO 21980:2020 The-Shelf (COTS) parts for use on low-orbit satellite Road vehicles — Liquefied petroleum gas (LPG) fuel systems 87 ISO 20766-11:2020 components — Part 11: Manual shut-off valve 88 ISO 349:2020 Hard coal — Audibert-Arnu dilatometer test Petroleum and related products — Precision of measurement methods 89 ISO 4259-3:2020 and results — Part 3: Monitoring and verification of published precision data in relation to methods of test Social responsibility and sustainable development — Guidance on using 90 ISO/TS 26030:2019 ISO 26000:2010 in the food chain Simultaneous interpreting delivery platforms — Requirements and 91 ISO/PAS 24019:2020 recommendations Rubber, vulcanized — Determination of low-temperature characteristics 92 ISO 2921:2019 — Temperature-retraction procedure (TR test) 93 ISO 28620:2020 Medical devices — Non-electrically driven portable infusion devices

Martial arts — Protective equipment for martial arts — Part 9: Additional 94 ISO 21924-9:2020 requirements and test methods for Wushu Sanda head protectors Measurement of radioactivity in the environment — Air: radon-222 — 95 ISO 11665-3:2020 Part 3: Spot measurement method of the potential alpha energy concentration of its short-lived decay products Measurement of radioactivity in the environment — Air: radon-222 — 96 ISO 11665-5:2020 Part 5: Continuous measurement methods of the activity concentration

Measurement of radioactivity in the environment — Air: radon-222 — 97 ISO 11665-6:2020 Part 6: Spot measurement methods of the activity concentration Hydraulic fluid power — Test methods for couplings actuated with or 98 ISO 18869:2017 without tools Water quality — Radium 226 and Radium 228 — Test method using 99 ISO 22908:2020 liquid scintillation counting Optics and photonics — Lasers and laser-related equipment — Test 100 ISO 11551:2019 method for absorptance of optical laser components 101 ISO 21801-1:2020 Cognitive accessibility — Part 1: General guidelines Geotechnical investigation and testing — Geotechnical monitoring by 102 ISO 18674-3:2017/Amd 1:2020 field instrumentation — Part 3: Measurement of displacements across a line: Inclinometers — Amendment 1 Biological evaluation of medical devices — Part 18: Chemical 103 ISO 10993-18:2020 characterization of medical device materials within a risk management process Building construction machinery and equipment — Portable, hand-held, internal combustion engine-driven abrasive cutting machines — Part 1: 104 ISO 19432-1:2020 Safety requirements for cut-off machines for centre-mounted rotating abrasive wheels Additive manufacturing — Process characteristics and performance — 105 ISO/ASTM 52904:2019 Practice for metal powder bed fusion process to meet critical applications Fine bubble technology — Cleaning applications — Part 2: Test method 106 ISO 21256-2:2020 for cleaning machine-oil stained surfaces of machined metal parts Use of reclaimed water in industrial cooling systems — Part 1: 107 ISO 22449-1:2020 Technical guidelines Information security, cybersecurity and privacy protection — Guidelines 108 ISO/IEC 27007:2020 for information security management systems auditing Rubber and rubber products — Determination of chlorine and bromine 109 ISO 7725:2020 content Comparison of toxic gas data from different tests — Part 1: Guidance 110 ISO 29903-1:2020 and requirements Plastics piping systems for non-pressure underground drainage and sewerage — Structured-wall piping systems of unplasticized poly(vinyl 111 ISO 21138-1:2020 chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) — Part 1: Material specification and performance criteria for pipes, fittings and systems Plastics piping systems for non-pressure underground drainage and sewerage — Structured-wall piping systems of unplasticized poly(vinyl 112 ISO 21138-2:2020 chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) — Part 2: Pipes and fittings with smooth external surface, Type A

Plastics piping systems for non-pressure underground drainage and sewerage — Structured-wall piping systems of unplasticized poly(vinyl 113 ISO 21138-3:2020 chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) — Part 3: Pipes and fittings with non-smooth external surface, Type B Plastics pipes and fittings — Butt fusion jointing procedures for 114 ISO 21307:2017/Amd 1:2020 polyethylene (PE) piping systems — Amendment 1 Medical electrical equipment — Part 2-31: Particular requirements for 115 IEC 60601-2-31:2020 the basic safety and essential performance of external cardiac pacemakers with internal power source Intelligent transport systems — Definition of data elements and data 116 ISO/TS 19082:2020 frames between roadside modules and signal controllers for cooperative signal control Geographic information — Geodetic references — Part 1: International 117 ISO 19161-1:2020 terrestrial reference system (ITRS) 118 ISO/TS 21831:2020 Information model of Chinese materia medica processing 119 ISO 21404:2020 Solid biofuels — Determination of ash melting behaviour