DOCSLIB.ORG

Measuring Length, Mass, Volume, and Temperature Label Your (Adapted from Prentice-Hall, Inc

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Measuring Length, Mass, Volume, and Temperature Label Your (Adapted from Prentice-Hall, Inc Name______________________________ Class __________________ Date ______________ Don’t forget to Measuring Length, Mass, Volume, and Temperature label your (Adapted from Prentice-Hall, Inc. Biology Lab Manual B) answers with the correct units! Introduction : Doing experiments is an important part of science. Most experiments include making measurements. Many different quantities can be measured. Some examples are length, mass, volume, temperature, and time. Some quantities, such as length, can be measured directly. Others, such as speed, are calculated from other measurements. In science you will probably use metric units to estimate, measure, and record data. The three fundamental metric units are the meter for length, the gram for mass, and the liter for capacity. In this investigation you will carry out different types of measurements. Problem : What types of measurements are used to describe quantities? Pre-Lab Discussion: Read the entire investigation. Then, work with a partner to answer the following questions. 1. How will you record a distance that is 2 centimeters longer than 5 meters? ________ 2 centimeters shorter? _______ 2. Why would you measure the contents of a paper cup in milliliters (mL) rather than in liters? 3. Explain why don’t measurements start at the beginning of a ruler, yard stick, meter stick, etc? (the zero point is always a little bit offset from the end) Materials (per group): meter stick 2 paper cups millimeter ruler 30 cm of string 250-mL graduated cylinder golf ball tripple beam balance 1 sheet college-ruled notebook paper thermometer Toy car (like a hotwheels car) Safety : Wear your lab apron and safety goggles while dealing with glassware. Procedure: 1. Measure and record the length and width of a piece of notebook paper in centimeters. length: ________________ width: _________________ 2. Picture in your mind a familiar distance nearby that you think is 5 m long. Write a description of this distance below (for example, “The distance from our classroom to room 203 down the hall”). Then measure the distance with a meter stick and record your result. Area measured: _________________________________________________________________________ length: ________________ How good was your estimate? 3. Measure and record the space between two lines on a piece of college-ruled notebook paper in millimeters. length: ________________ 4. Using a triple beam balance, find and record the mass in grams of a hotwheels toy car. mass: ________________ 5. Fill a paper cup about two-thirds full with water. Pour the water into the graduated cylinder and record its volume in milliliters. volume: ________________ 6. Place the thermometer in the water and find its temperature. Record your measurement below. cool tap water: ________________ 7. What is the difference between surface area and volume? 8. A prism measures 2cm in height, 2cm in width, and 5cm in length. Calculate the surface area and volume of the prism. surface area: __________________ volume: ___________________ 9. Imagine that the prism in question #8 is pliable and malleable. Can you increase its surface area without changing the volume? Explain. 8. Find the volume of a golf ball in cm3 using the displacement of water (a technique often used for finding the volume of irregular objects). Fill a beaker half full of water. Record the volume of the water in mL. Place the golf ball in the beaker of water. Record the volume of water in mL. The water displaced is equal to the volume of the golf ball. (1 mL of water = 1 cm3) Initial volume of water: __________________ Final volume of water: __________________ Volume of golf ball: __________________ 9. The raider cross country team was a bit tired this morning, so they took an easy morning stroll. Using the map of the route below, find the distance that they ran in kilometers. Hint: A string can be a useful tool when measuring the circumference of an object as well as lines that are not straight. Distance: ____________________ Analysis and Conclusions: 1. One student measured the height of a plant as 52 mm. Another student measured the same plant to the nearest tenth of a centimeter. What was the second student’s measurement? Was one method more precise? Explain your answer. 2. Why might two people measuring the same temperature get very different results? 3. Why might it be a good practice to measure a quantity several times and average the results? .
Load more

Recommended publications
  • Metric System Units of Length
    Math 0300 METRIC SYSTEM UNITS OF LENGTH Þ To convert units of length in the metric system of measurement The basic unit of length in the metric system is the meter. All units of length in the metric system are derived from the meter. The prefix “centi-“means one hundredth. 1 centimeter=1 one-hundredth of a meter kilo- = 1000 1 kilometer (km) = 1000 meters (m) hecto- = 100 1 hectometer (hm) = 100 m deca- = 10 1 decameter (dam) = 10 m 1 meter (m) = 1 m deci- = 0.1 1 decimeter (dm) = 0.1 m centi- = 0.01 1 centimeter (cm) = 0.01 m milli- = 0.001 1 millimeter (mm) = 0.001 m Conversion between units of length in the metric system involves moving the decimal point to the right or to the left. Listing the units in order from largest to smallest will indicate how many places to move the decimal point and in which direction. Example 1: To convert 4200 cm to meters, write the units in order from largest to smallest. km hm dam m dm cm mm Converting cm to m requires moving 4 2 . 0 0 2 positions to the left. Move the decimal point the same number of places and in the same direction (to the left). So 4200 cm = 42.00 m A metric measurement involving two units is customarily written in terms of one unit. Convert the smaller unit to the larger unit and then add. Example 2: To convert 8 km 32 m to kilometers First convert 32 m to kilometers. km hm dam m dm cm mm Converting m to km requires moving 0 .
    [Show full text]
  • Lesson 1: Length English Vs
    Lesson 1: Length English vs. Metric Units Which is longer? A. 1 mile or 1 kilometer B. 1 yard or 1 meter C. 1 inch or 1 centimeter English vs. Metric Units Which is longer? A. 1 mile or 1 kilometer 1 mile B. 1 yard or 1 meter C. 1 inch or 1 centimeter 1.6 kilometers English vs. Metric Units Which is longer? A. 1 mile or 1 kilometer 1 mile B. 1 yard or 1 meter C. 1 inch or 1 centimeter 1.6 kilometers 1 yard = 0.9444 meters English vs. Metric Units Which is longer? A. 1 mile or 1 kilometer 1 mile B. 1 yard or 1 meter C. 1 inch or 1 centimeter 1.6 kilometers 1 inch = 2.54 centimeters 1 yard = 0.9444 meters Metric Units The basic unit of length in the metric system in the meter and is represented by a lowercase m. Standard: The distance traveled by light in absolute vacuum in 1∕299,792,458 of a second. Metric Units 1 Kilometer (km) = 1000 meters 1 Meter = 100 Centimeters (cm) 1 Meter = 1000 Millimeters (mm) Which is larger? A. 1 meter or 105 centimeters C. 12 centimeters or 102 millimeters B. 4 kilometers or 4400 meters D. 1200 millimeters or 1 meter Measuring Length How many millimeters are in 1 centimeter? 1 centimeter = 10 millimeters What is the length of the line in centimeters? _______cm What is the length of the line in millimeters? _______mm What is the length of the line to the nearest centimeter? ________cm HINT: Round to the nearest centimeter – no decimals.
    [Show full text]
  • Distances in the Solar System Are Often Measured in Astronomical Units (AU). One Astronomical Unit Is Defined As the Distance from Earth to the Sun
    Distances in the solar system are often measured in astronomical units (AU). One astronomical unit is defined as the distance from Earth to the Sun. 1 AU equals about 150 million km (93 million miles). Table below shows the distance from the Sun to each planet in AU. The table shows how long it takes each planet to spin on its axis. It also shows how long it takes each planet to complete an orbit. Notice how slowly Venus rotates! A day on Venus is actually longer than a year on Venus! Distances to the Planets and Properties of Orbits Relative to Earth's Orbit Average Distance Length of Day (In Earth Length of Year (In Earth Planet from Sun (AU) Days) Years) Mercury 0.39 AU 56.84 days 0.24 years Venus 0.72 243.02 0.62 Earth 1.00 1.00 1.00 Mars 1.52 1.03 1.88 Jupiter 5.20 0.41 11.86 Saturn 9.54 0.43 29.46 Uranus 19.22 0.72 84.01 Neptune 30.06 0.67 164.8 The Role of Gravity Planets are held in their orbits by the force of gravity. What would happen without gravity? Imagine that you are swinging a ball on a string in a circular motion. Now let go of the string. The ball will fly away from you in a straight line. It was the string pulling on the ball that kept the ball moving in a circle. The motion of a planet is very similar to the ball on a strong.
    [Show full text]
  • Measuring the Astronomical Unit from Your Backyard Two Astronomers, Using Amateur Equipment, Determined the Scale of the Solar System to Better Than 1%
    Measuring the Astronomical Unit from Your Backyard Two astronomers, using amateur equipment, determined the scale of the solar system to better than 1%. So can you. By Robert J. Vanderbei and Ruslan Belikov HERE ON EARTH we measure distances in millimeters and throughout the cosmos are based in some way on distances inches, kilometers and miles. In the wider solar system, to nearby stars. Determining the astronomical unit was as a more natural standard unit is the tUlronomical unit: the central an issue for astronomy in the 18th and 19th centu· mean distance from Earth to the Sun. The astronomical ries as determining the Hubble constant - a measure of unit (a.u.) equals 149,597,870.691 kilometers plus or minus the universe's expansion rate - was in the 20th. just 30 meters, or 92,955.807.267 international miles plus or Astronomers of a century and more ago devised various minus 100 feet, measuring from the Sun's center to Earth's ingenious methods for determining the a. u. In this article center. We have learned the a. u. so extraordinarily well by we'll describe a way to do it from your backyard - or more tracking spacecraft via radio as they traverse the solar sys­ precisely, from any place with a fairly unobstructed view tem, and by bouncing radar Signals off solar.system bodies toward the east and west horizons - using only amateur from Earth. But we used to know it much more poorly. equipment. The method repeats a historic experiment per­ This was a serious problem for many brancht:s of as­ formed by Scottish astronomer David Gill in the late 19th tronomy; the uncertain length of the astronomical unit led century.
    [Show full text]
  • Multidisciplinary Design Project Engineering Dictionary Version 0.0.2
    Multidisciplinary Design Project Engineering Dictionary Version 0.0.2 February 15, 2006 . DRAFT Cambridge-MIT Institute Multidisciplinary Design Project This Dictionary/Glossary of Engineering terms has been compiled to compliment the work developed as part of the Multi-disciplinary Design Project (MDP), which is a programme to develop teaching material and kits to aid the running of mechtronics projects in Universities and Schools. The project is being carried out with support from the Cambridge-MIT Institute undergraduate teaching programe. For more information about the project please visit the MDP website at http://www-mdp.eng.cam.ac.uk or contact Dr. Peter Long Prof. Alex Slocum Cambridge University Engineering Department Massachusetts Institute of Technology Trumpington Street, 77 Massachusetts Ave. Cambridge. Cambridge MA 02139-4307 CB2 1PZ. USA e-mail: [email protected] e-mail: [email protected] tel: +44 (0) 1223 332779 tel: +1 617 253 0012 For information about the CMI initiative please see Cambridge-MIT Institute website :- http://www.cambridge-mit.org CMI CMI, University of Cambridge Massachusetts Institute of Technology 10 Miller’s Yard, 77 Massachusetts Ave. Mill Lane, Cambridge MA 02139-4307 Cambridge. CB2 1RQ. USA tel: +44 (0) 1223 327207 tel. +1 617 253 7732 fax: +44 (0) 1223 765891 fax. +1 617 258 8539 . DRAFT 2 CMI-MDP Programme 1 Introduction This dictionary/glossary has not been developed as a definative work but as a useful reference book for engi- neering students to search when looking for the meaning of a word/phrase. It has been compiled from a number of existing glossaries together with a number of local additions.
    [Show full text]
  • Measuring in Metric Units BEFORE Now WHY? You Used Metric Units
    Measuring in Metric Units BEFORE Now WHY? You used metric units. You’ll measure and estimate So you can estimate the mass using metric units. of a bike, as in Ex. 20. Themetric system is a decimal system of measurement. The metric Word Watch system has units for length, mass, and capacity. metric system, p. 80 Length Themeter (m) is the basic unit of length in the metric system. length: meter, millimeter, centimeter, kilometer, Three other metric units of length are themillimeter (mm) , p. 80 centimeter (cm) , andkilometer (km) . mass: gram, milligram, kilogram, p. 81 You can use the following benchmarks to estimate length. capacity: liter, milliliter, kiloliter, p. 82 1 millimeter 1 centimeter 1 meter thickness of width of a large height of the a dime paper clip back of a chair 1 kilometer combined length of 9 football fields EXAMPLE 1 Using Metric Units of Length Estimate the length of the bandage by imagining paper clips laid next to it. Then measure the bandage with a metric ruler to check your estimate. 1 Estimate using paper clips. About 5 large paper clips fit next to the bandage, so it is about 5 centimeters long. ch O at ut! W 2 Measure using a ruler. A typical metric ruler allows you to measure Each centimeter is divided only to the nearest tenth of into tenths, so the bandage cm 12345 a centimeter. is 4.8 centimeters long. 80 Chapter 2 Decimal Operations Mass Mass is the amount of matter that an object has. The gram (g) is the basic metric unit of mass.
    [Show full text]
  • Hydraulics Manual Glossary G - 3
    Glossary G - 1 GLOSSARY OF HIGHWAY-RELATED DRAINAGE TERMS (Reprinted from the 1999 edition of the American Association of State Highway and Transportation Officials Model Drainage Manual) G.1 Introduction This Glossary is divided into three parts: · Introduction, · Glossary, and · References. It is not intended that all the terms in this Glossary be rigorously accurate or complete. Realistically, this is impossible. Depending on the circumstance, a particular term may have several meanings; this can never change. The primary purpose of this Glossary is to define the terms found in the Highway Drainage Guidelines and Model Drainage Manual in a manner that makes them easier to interpret and understand. A lesser purpose is to provide a compendium of terms that will be useful for both the novice as well as the more experienced hydraulics engineer. This Glossary may also help those who are unfamiliar with highway drainage design to become more understanding and appreciative of this complex science as well as facilitate communication between the highway hydraulics engineer and others. Where readily available, the source of a definition has been referenced. For clarity or format purposes, cited definitions may have some additional verbiage contained in double brackets [ ]. Conversely, three “dots” (...) are used to indicate where some parts of a cited definition were eliminated. Also, as might be expected, different sources were found to use different hyphenation and terminology practices for the same words. Insignificant changes in this regard were made to some cited references and elsewhere to gain uniformity for the terms contained in this Glossary: as an example, “groundwater” vice “ground-water” or “ground water,” and “cross section area” vice “cross-sectional area.” Cited definitions were taken primarily from two sources: W.B.
    [Show full text]
  • Glossary of Materials Engineering Terminology
    Glossary of Materials Engineering Terminology Adapted from: Callister, W. D.; Rethwisch, D. G. Materials Science and Engineering: An Introduction, 8th ed.; John Wiley & Sons, Inc.: Hoboken, NJ, 2010. McCrum, N. G.; Buckley, C. P.; Bucknall, C. B. Principles of Polymer Engineering, 2nd ed.; Oxford University Press: New York, NY, 1997. Brittle fracture: fracture that occurs by rapid crack formation and propagation through the material, without any appreciable deformation prior to failure. Crazing: a common response of plastics to an applied load, typically involving the formation of an opaque banded region within transparent plastic; at the microscale, the craze region is a collection of nanoscale, stress-induced voids and load-bearing fibrils within the material’s structure; craze regions commonly occur at or near a propagating crack in the material. Ductile fracture: a mode of material failure that is accompanied by extensive permanent deformation of the material. Ductility: a measure of a material’s ability to undergo appreciable permanent deformation before fracture; ductile materials (including many metals and plastics) typically display a greater amount of strain or total elongation before fracture compared to non-ductile materials (such as most ceramics). Elastic modulus: a measure of a material’s stiffness; quantified as a ratio of stress to strain prior to the yield point and reported in units of Pascals (Pa); for a material deformed in tension, this is referred to as a Young’s modulus. Engineering strain: the change in gauge length of a specimen in the direction of the applied load divided by its original gauge length; strain is typically unit-less and frequently reported as a percentage.
    [Show full text]
  • Measuring Length, Mass, Volume, and Temperature
    Name______________________________ Class __________________ Date ______________ Chapter 1 The Science of Biology You may want to refer students to Measuring Length, Mass, Volume, Section 1–4 and Appendix C in the textbook for a discussion of and Temperature measurement. Time required: 40 minutes Introduction Doing experiments is an important part of science. Most experiments include making measurements. Many different quantities can be measured. Some examples are length, mass, volume, temperature, and time. Some quantities, such as length, can be measured directly. Others, such as speed, are calculated from other measurements. In science you will probably use metric units to estimate, measure, and record data. The three fundamental metric units are the meter for length, the gram for mass, and the liter for capacity. In this investigation you will carry out different types of measurements. Problem What types of measurements are used to describe quantities? Pre-Lab Discussion Read the entire investigation. Then, work with a partner to answer the following questions. 1. Which of the measurements in the investigation are familiar to you? Which will be new to you? Measuring mass and liquid volume may be less familiar to students than measuring length and temperature. 2. How will you record a distance that is 2 centimeters longer than 5 meters? 2 centimeters shorter? 5.02 m (or 5 m 2 cm); 4.98 m (or 4 m 98 cm). Remind students that 1 cm equals 0.01 m. If necessary, review converting between centimeters and meters. 3. How will you choose an object to measure in millimeters? Millimeters are very small, so the length to be measured should not be too large.
    [Show full text]
  • IAU 2012 Resolution B2
    RESOLUTION B2 on the re-definition of the astronomical unit of length. Proposed by the IAU Division I Working Group Numerical Standards and supported by Division I The XXVIII General Assembly of International Astronomical Union, noting 1. that the International Astronomical Union (IAU) 1976 System of Astronomical Constants specifies the units for the dynamics of the solar system, including the day (D=86400 s), the mass of the Sun, MS, and the astronomical unit of length or simply the astronomical unit whose definitioni is based on the value of the Gaussian gravitational constant, 2. that the intention of the above definition of the astronomical unit was to provide accurate distance ratios in the solar system when distances could not be estimated with high accuracy, 3. that, to calculate the solar mass parameter, GMS, previously known as the heliocentric gravitation constant, in Système International (SI) unitsii,the Gaussian gravitational constant k, is used, along with an astronomical unit determined observationally, 4. that the IAU 2009 System of astronomical constants (IAU 2009 Resolution B2) retains the IAU 1976 definition of the astronomical unit, by specifying k as an “auxiliary defining constant” with the numerical value given in the IAU 1976 System of Astronomical Constants, 5. that the value of the astronomical unit compatible with Barycentric Dynamical Time (TDB) in Table 1 of the IAU 2009 System (149 597 870 700 m 3 m), is an average (Pitjeva and Standish 2009) of recent estimates for the astronomical unit defined by k, 6. that the TDB-compatible value for GMS listed in Table 1 of the IAU 2009 System, derived by using the astronomical unit fit to the DE421 ephemerides (Folkner et al.
    [Show full text]
  • The International System of Units (SI) - Conversion Factors For
    NIST Special Publication 1038 The International System of Units (SI) – Conversion Factors for General Use Kenneth Butcher Linda Crown Elizabeth J. Gentry Weights and Measures Division Technology Services NIST Special Publication 1038 The International System of Units (SI) - Conversion Factors for General Use Editors: Kenneth S. Butcher Linda D. Crown Elizabeth J. Gentry Weights and Measures Division Carol Hockert, Chief Weights and Measures Division Technology Services National Institute of Standards and Technology May 2006 U.S. Department of Commerce Carlo M. Gutierrez, Secretary Technology Administration Robert Cresanti, Under Secretary of Commerce for Technology National Institute of Standards and Technology William Jeffrey, Director Certain commercial entities, equipment, or materials may be identified in this document in order to describe an experimental procedure or concept adequately. Such identification is not intended to imply recommendation or endorsement by the National Institute of Standards and Technology, nor is it intended to imply that the entities, materials, or equipment are necessarily the best available for the purpose. National Institute of Standards and Technology Special Publications 1038 Natl. Inst. Stand. Technol. Spec. Pub. 1038, 24 pages (May 2006) Available through NIST Weights and Measures Division STOP 2600 Gaithersburg, MD 20899-2600 Phone: (301) 975-4004 — Fax: (301) 926-0647 Internet: www.nist.gov/owm or www.nist.gov/metric TABLE OF CONTENTS FOREWORD.................................................................................................................................................................v
    [Show full text]
  • Dimensional Analysis and Modeling
    cen72367_ch07.qxd 10/29/04 2:27 PM Page 269 CHAPTER DIMENSIONAL ANALYSIS 7 AND MODELING n this chapter, we first review the concepts of dimensions and units. We then review the fundamental principle of dimensional homogeneity, and OBJECTIVES Ishow how it is applied to equations in order to nondimensionalize them When you finish reading this chapter, you and to identify dimensionless groups. We discuss the concept of similarity should be able to between a model and a prototype. We also describe a powerful tool for engi- ■ Develop a better understanding neers and scientists called dimensional analysis, in which the combination of dimensions, units, and of dimensional variables, nondimensional variables, and dimensional con- dimensional homogeneity of equations stants into nondimensional parameters reduces the number of necessary ■ Understand the numerous independent parameters in a problem. We present a step-by-step method for benefits of dimensional analysis obtaining these nondimensional parameters, called the method of repeating ■ Know how to use the method of variables, which is based solely on the dimensions of the variables and con- repeating variables to identify stants. Finally, we apply this technique to several practical problems to illus- nondimensional parameters trate both its utility and its limitations. ■ Understand the concept of dynamic similarity and how to apply it to experimental modeling 269 cen72367_ch07.qxd 10/29/04 2:27 PM Page 270 270 FLUID MECHANICS Length 7–1 ■ DIMENSIONS AND UNITS 3.2 cm A dimension is a measure of a physical quantity (without numerical val- ues), while a unit is a way to assign a number to that dimension.
    [Show full text]