1300 885 886 Independent Living Centres Advisory

Product Details With suppliers in N/A Coway Range of (PR01284) https://ilcaustralia.org.au/products/1284

A range of units which replace a conventional seat. They fit most standard and can be installed onto a specific over toilet frame. Available in electric and non- electric. The electric models provide adjustable temperature, pressure and range for the cleansing spray jet, adjustable warm air drying and seat temperature. An elongated seat (for larger users) is available for on some models. We recommend checking your state or territory regulations as some products must be installed by a licensed plumber to COWAY BA08 Bidet comply with legislative requirements. Toilet raiser and support arm options are available to attach to bidet. General Details

Caution Do not climb on the seat cover or body Do not lean against the seat cover. Do not insert a steel wire or sharp items into any part of the unit as it may cause electrical hazards or damage. Do not place a stove or heater close to the product as it may distort or catch fire. Do not expose the product directly to the sun as the plastic could become discoloured. The water pressure level should be set at 1 to protect the anal region. To protect against low temperature burns, the temperature setting of the toilets, water and air dryer should be set to Low or Off.

Method of Use POWER: Plug the cord into the wall outlet. Press the Power button on the side control panel.

CLEANING CYCLES: Rear Cleansing (anal ): Press the "Rear Cleansing" button while sitting on the seat. Duration of wash cycle is pre set at 60 seconds. You can adjust nozzle position, spray ranges, water temperature and pressure and move function. Front Cleansing (): Press the "Front Cleansing" button while sitting on the seat. Duration of wash cycle is pre set at 60 seconds. You can adjust nozzle position, water temperature, pressure and move function.

DRYING: Press the "Air Dryer" button and warm air blows out for 2 minutes. The temperature is able to be adjusted using the up and down arrows.

Cleaning Requirements Exterior Cleaning: Wipe the exterior parts with a soft sponge or cloth applying a small amount of neutral detergent. Do not use any detergents containing hydrochloric acid, solvents or benzene.

Cleaning of Nozzles: Push "Nozzle Cleaning" button for three seconds or more. Front cleansing nozzle extend forward and stops. Scrub the nozzle with a toothbrush. Once clean push the "nozzle cleaning" button again. The Front nozzle returns and the the rear nozzle extends forwards and stops. Scrub the nozzle with a toothbrush. Once clean, push the "Stop" button and the rear nozzle will return. Hold the nozzle lightly while cleaning as excessive force may damage it. The nozzle returns automatically if no button is pushed for two minutes.

Extra product information Please ask supplier for the questionnaire/evaluation form that is required to be completed prior to installation.

===

The bidet is made of anti-bacterial plastic and has an operating unit, an ergonomic plastic and a hydraulic lid. The unit, toilet seat and lid are secured on to the original porcelain toilet bowl, replacing the original toilet seat and lid. The system has a filter for water purification with a life span of 6 months. The unit has a self diagnosis system to assist with detecting faults.

Adjustable angle spray jets are located at the rear and front of the toilet bowl. The spray jets automatically retract at the end of use to maintain hygiene. The warm air blow drier is located at the rear of the toilet bowl.

The unit has a side control panel with push button controls to activate or adjust the following: spray jets Nozzle position Water pressure Warm air drier Wide spray range Nozzle cleaning Water temperature Seat temperature Nozzle move mode.

The nozzle adjustment has five positions and the nozzles are self cleaning. The water pressure and air dryer temperature have three levels. You can adjust spray ranges for 3 different levels. Seat temperature has low (34 degrees C), moderate (37 degrees C), high (40 degrees C)and off levels. Water temperature has low (32 degrees C), moderate (36 degrees C), high (38 degrees C) and off levels.

An automatic power saving mode is available . If the seat sensor is not activated within a minute, water and seat temperature change to Low and after 30 minutes water, seat heater and LED lamps are turned off.

Arm supports and seat raisers: Throne toilet seat spacers (50mm and 80mm), Throne 3-in-1 toilet support arms and Throne bariatric toilet rails can be used with the bidets. Note - the Coway bidets raise the seat height by 50mm when installed.

Installation We recommend checking your state or territory regulations as some products must be installed by a licensed plumber to comply with legislative requirements.

This bidet is able to be self installed. A power point is needed within 2.5m of the bidet. 1. Remove the existing toilet seat and seat lid 2. Install the T valve: Turn off the water supply valve, separate the toilet hose from the water main pipe, then fix the T shape connector to existing water main pipe. Connect both the toilet cistern hose and bidet hose to the T shape connector. 3. Connect the Filter: Open the filter cap on the upper left of the body, put it inside the groove and turn it clockwise. 4. Placing the fixing plate: Push and fit the rear part of the main body of the bidet into the fixing plate and tighten the bolts. 5. Install the body: Place fixing plate, push fixing bolts into the fixing plate, and tighten the nuts until the fixing plate doesn't move. 6. Connect the bidet hose: Connect the bidet hose joined with the T shape connector to the main body of the unit.

Manufacturer/Country United States of America. Websites The Bidet Shop - http://www.thebidetshop.com.au/categories/Coway-Bidet/ Models / Specifications

Model BA 11: with wireless remote control unit. Features as per BA 07, with built in MP3 player, one-touch automatic lid, instant heating system and memory function to save preferred settings. Only available in elongated seat design.

Model BA 12: Non-electric bidet using room temperature filtered and aerated water stream via two self cleaning nozzles. Water pressure is adjustable. Jog-dial controller located on right of seat. No drier function. Available with black or white control.

Model BA 13: Electronic bidet with wireless remote control unit. Features as per BA 07, with stainless steel nozzles, air and water stream and ultra streamline design. Includes instant heating system and power save function. Available in regular and elongated seat.

Model BA 15: Electronic bidet with wireless remote control unit. Features as per BA 07, with power save function and gentle aerated water stream. Model BA 08: Electronic bidet with wireless remote control unit. Features as per BA 07, with enema function and aerated water stream. Available with child seat that includes safety arms/handles. Also available in regular and elongated seat size. Load Capacity (supplier stated) 200 kg

Model BA 07 : Electronic bidet with side control unit. It features cold or warm water rear cleansing with a range of nozzle position adjustments, the option of wide or moving spray, massage cleansing and drier function. Available in regular and elongated seat size. Load Capacity (supplier stated) 150 kg Suppliers (3)

Aidacare - https://ilcaustralia.org.au/suppliers/12912 See supplier website or your telephone directory for location of your nearest store.

Head office : 1300 216 898

Aidacare https://www.aidacare.com.au/ Online shop Mobility HQ https://www.mobilityhq.com.au/

Reece Plumbing Centres - https://ilcaustralia.org.au/suppliers/2212 See supplier website or your telephone directory for location of your nearest store.

Sales : 03 9274 0000 Fax : 03 9274 0198 Toll free : 1800 032 566

Reece Plumbing Centres www.reece.com.au Reece Plumbing Centres Store Locator www.reece.com.au/storefinder/

Tradelink (Head Office) - https://ilcaustralia.org.au/suppliers/1118 See supplier website or your telephone directory for location of your nearest store.

Fax : 07 3260 9750 Sales : 07 3260 9777 Toll free : 1800 228 476

Tradelink www.tradelink.com.au Tradelink Showroom Locator http://www.tradelink.com.au/showroom-locator Agents (0)

Importers (0)

Manufacturers (0) Images

Coway BA 08 Bidet

Coway BA 08 Bidet

Measurements of Coway bidet with 80mm Coway with toilet raiser (50 or 80mm height toilet raiser available) and arms

Coway with toilet raiser and bariatric arms

Maintenance

Refer to the supplier and manufacturer manual for maintenance instructions and safety warnings. Standards

Some assistive technology needs to meet Australian or other standards. Standards may relate to materials, manufacturing, and installation. Products that meet Australian or international standards will have written certification. To find out if a product meets Australian Standards ask the supplier to show you the certificate. For more information about standards see http://www.ilcaustralia.org.au/Using_Assistive_Technology/standards_regulation Disclaimer

Independent Living Centres Australia (ILCA) does not design or make products. ILCA cannot guarantee that all information given is correct. Prices shown are a rough guide. Some products may incur GST. Check with suppliers for up-to-date prices. The display of products at an ILCA centre, or details given in print, is only for your information. It is not a recommendation. You should always get professional advice when choosing products. The person choosing the product is responsible for their choice. ILCA takes no responsibility for people choosing equipment or services which will cause (or be alleged to have caused) loss or injury. You must follow the manufacturer’s or service provider’s instructions when using equipment or services.

Copyright ILCA 2011. All rights reserved