Analog IC Design - the Obsolete Book

Total Page：16

File Type：pdf, Size：1020Kb

Analog IC design - the obsolete book Ricardo Erckert July 2021 Contents 1 Preface 7 1.1 Using the book . 7 1.2 If you find mistakes . 8 1.3 Copying . 8 1.4 Warranty and Liability . 8 2 The top level of a chip 8 2.1 How to get the correct data of a chip . 8 2.1.1 Versioning tools . 9 2.2 System on a chip . 11 2.2.1 Where exactly is “ground”? . 12 2.2.2 Signals: If anything can go wrong it will! . 12 2.2.3 Timings . 14 2.3 Top level . 14 2.4 Hierarchy of the chip . 15 2.4.1 Analog on top . 15 2.5 Down at the bottom . 16 2.5.1 Electric . 16 2.5.2 Xcircuit . 17 3 From wafer to chip 18 3.1 Choice of the right substrate . 20 3.1.1 Junction isolated P- substrate . 20 3.1.2 Junction Isolated P+ substrate . 21 3.1.3 Junction isolated N- substrate . 22 3.1.4 Junction isolated N+ substrate . 22 3.1.5 Oxide isolated technology with N-tubs . 23 3.1.6 Oxide isolated technology with P-tubs . 26 3.2 Examples of more complex processes . 26 3.2.1 A bipolar process . 26 3.2.2 A BCD (bipolar, CMOS, DMOS) power process . 27 3.2.3 An isolated (ABCD - advanced BCD) power process . 28 3.2.4 A non volatile memory process . 29 3.2.5 State of the art (2020) digital processes . 29 3.2.6 Programmable chips . 29 4 Components 31 4.1 Wires . 31 4.1.1 Electromigration . 31 4.1.2 Resistance of a wire . 32 4.1.3 The via how to . 33 4.1.4 Wires acting as antennas . 34 4.2 Contacts . 37 4.2.1 Local interconnect . 38 4.2.2 Device matching . 38 4.2.3 Seebeck effect . 38 4.3 Resistors . 39 4.3.1 Poly silicon resistors . 39 4.3.2 Thermal Noise of a resistors . 40 4.3.3 Poly silicon resistor aging: . 40 1 4.3.4 Resistor matching . 41 4.3.5 Diffused resistors . 41 4.4 Capacitors . 41 4.4.1 Junction capacitors . 42 4.4.2 Poly silicon capacitors . 43 4.4.3 Isolated poly silicon capacitors . 43 4.4.4 Metal capacitors . 43 4.4.5 Noise of a capacitor (KTC-noise) . 44 4.4.6 Parasitic resistance . 45 4.4.7 Capacitor matching . 45 4.4.8 Maximum voltage of a capacitor . 45 4.4.9 External capacitors . 46 4.5 Inductors . 47 4.5.1 External inductors . 47 4.5.2 Transformers . 49 4.5.3 Transducers . 50 4.6 MOS transistors . 50 4.6.1 NMOS transistors . 51 4.6.2 PMOS transistors . 61 4.7 Bipolar transistors and diodes . 62 4.7.1 Bipolar Diodes . 62 4.7.2 Vertical NPN transistors . 66 4.7.3 High Voltage NPN transistors . 68 4.7.4 NPN power transistors . 71 4.7.5 Lateral NPN transistors . 71 4.7.6 PNP transistors . 73 4.7.7 Lateral PNP transistor . 73 4.8 Special devices . 74 4.8.1 Vertical DMOS . 75 4.8.2 Lateral DMOS . 76 4.8.3 High voltage PMOS . 76 4.8.4 Substrate power PNP transistor . 76 4.8.5 Substrate power DMOS . 77 4.8.6 SiC transistors . 80 4.8.7 GaN transistors . 81 4.8.8 IGBT (Isolated gate bipolar transistor) . 82 4.8.9 Thyristors . ..

495

Copy Link

Recommended publications

Chapter 19 - the Oscillator
Chapter 19 - The Oscillator The Electronics Curse “Your amplifiers will oscillate, your oscillators won't!” Question, What is an Oscillator? A Pendulum is an Oscillator... “Oscillators are circuits that are used to generate A.C. signals. Although mechanical methods, like alternators, can be used to generate low frequency A.C. signals, such as the 50 Hz mains, electronic circuits are the most practical way of generating signals at radio frequencies.” Comment: Hmm, wasn't always. In the time of Marconi, generators were used to generate a frequency to transmit. We are talking about kiloWatts of power! e.g. Grimeton L.F. Transmitter. Oscillators are widely used in both transmitters and receivers. In transmitters they are used to generate the radio frequency signal that will ultimately be applied to the antenna, causing it to transmit. In receivers, oscillators are widely used in conjunction with mixers (a circuit that will be covered in a later module) to change the frequency of the received radio signal. Principal of Operation The diagram below is a ‘block diagram’ showing a typical oscillator. Block diagrams differ from the circuit diagrams that we have used so far in that they do not show every component in the circuit individually. Instead they show complete functional blocks – for example, amplifiers and filters – as just one symbol in the diagram. They are useful because they allow us to get a high level overview of how a circuit or system functions without having to show every individual component. The Barkhausen Criterion [That's NOT ‘dog box’ in German!] Comment: In electronics, the Barkhausen stability criterion is a mathematical condition to determine when a linear electronic circuit will oscillate.
[Show full text]
Analysis of BJT Colpitts Oscillators - Empirical and Mathematical Methods for Predicting Behavior Nicholas Jon Stave Marquette University
Marquette University e-Publications@Marquette Master's Theses (2009 -) Dissertations, Theses, and Professional Projects Analysis of BJT Colpitts Oscillators - Empirical and Mathematical Methods for Predicting Behavior Nicholas Jon Stave Marquette University Recommended Citation Stave, Nicholas Jon, "Analysis of BJT Colpitts sO cillators - Empirical and Mathematical Methods for Predicting Behavior" (2019). Master's Theses (2009 -). 554. https://epublications.marquette.edu/theses_open/554 ANALYSIS OF BJT COLPITTS OSCILLATORS – EMPIRICAL AND MATHEMATICAL METHODS FOR PREDICTING BEHAVIOR by Nicholas J. Stave, B.Sc. A Thesis submitted to the Faculty of the Graduate School, Marquette University, in Partial Fulfillment of the Requirements for the Degree of Master of Science Milwaukee, Wisconsin August 2019 ABSTRACT ANALYSIS OF BJT COLPITTS OSCILLATORS – EMPIRICAL AND MATHEMATICAL METHODS FOR PREDICTING BEHAVIOR Nicholas J. Stave, B.Sc. Marquette University, 2019 Oscillator circuits perform two fundamental roles in wireless communication – the local oscillator for frequency shifting and the voltage-controlled oscillator for modulation and detection. The Colpitts oscillator is a common topology used for these applications. Because the oscillator must function as a component of a larger system, the ability to predict and control its output characteristics is necessary. Textbooks treating the circuit often omit analysis of output voltage amplitude and output resistance and the literature on the topic often focuses on gigahertz-frequency chip-based applications. Without extensive component and parasitics information, it is often difficult to make simulation software predictions agree with experimental oscillator results. The oscillator studied in this thesis is the bipolar junction Colpitts oscillator in the common-base configuration and the analysis is primarily experimental. The characteristics considered are output voltage amplitude, output resistance, and sinusoidal purity of the waveform.
[Show full text]
Oscillator Design
Oscillator Design •Introduction –What makes an oscillator? •Types of oscillators –Fixed frequency or voltage controlled oscillator –LC resonator –Ring Oscillator –Crystal resonator •Design of oscillators –Frequency control, stability –Amplitude limits –Buffered output –isolation –Bias circuits –Voltage control –Phase noise 1 Oscillator Requirements •Power source •Frequency-determining components •Active device to provide gain •Positive feedback LC Oscillator fr = 1/ 2p LC Hartley Crystal Colpitts Clapp RC Wien-Bridge Ring 2 Feedback Model for oscillators x A(jw) i xo A (jw) = A f 1 - A(jω)×b(jω) x = x + x d i f Barkhausen criteria x f A( jw)× b ( jω) =1 β Barkhausen’scriteria is necessary but not sufficient. If the phase shift around the loop is equal to 360o at zero frequency and the loop gain is sufficient, the circuit latches up rather than oscillate. To stabilize the frequency, a frequency-selective network is added and is named as resonator. Automatic level control needed to stabilize magnitude 3 General amplitude control •One thought is to detect oscillator amplitude, and then adjust Gm so that it equals a desired value •By using feedback, we can precisely achieve GmRp= 1 •Issues •Complex, requires power, and adds noise 4 Leveraging Amplifier Nonlinearity as Feedback •Practical trans-conductance amplifiers have saturating characteristics –Harmonics created, but filtered out by resonator –Our interest is in the relationship between the input and the fundamental of the output •As input amplitude is increased –Effective gain from input
[Show full text]
Lec#12: Sine Wave Oscillators
Integrated Technical Education Cluster Banna - At AlAmeeria ‎ © Ahmad El J-601-1448 Electronic Principals Lecture #12 Sine wave oscillators Instructor: Dr. Ahmad El-Banna 2015 January Banna Agenda - © Ahmad El Introduction Feedback Oscillators Oscillators with RC Feedback Circuits 1448 Lec#12 , Jan, 2015 Oscillators with LC Feedback Circuits - 601 - J Crystal-Controlled Oscillators 2 INTRODUCTION 3 J-601-1448 , Lec#12 , Jan 2015 © Ahmad El-Banna Banna Introduction - • An oscillator is a circuit that produces a periodic waveform on its output with only the dc supply voltage as an input. © Ahmad El • The output voltage can be either sinusoidal or non sinusoidal, depending on the type of oscillator. • Two major classifications for oscillators are feedback oscillators and relaxation oscillators. o an oscillator converts electrical energy from the dc power supply to periodic waveforms. 1448 Lec#12 , Jan, 2015 - 601 - J 4 FEEDBACK OSCILLATORS FEEDBACK 5 J-601-1448 , Lec#12 , Jan 2015 © Ahmad El-Banna Banna Positive feedback - • Positive feedback is characterized by the condition wherein a portion of the output voltage of an amplifier is fed © Ahmad El back to the input with no net phase shift, resulting in a reinforcement of the output signal. Basic elements of a feedback oscillator. 1448 Lec#12 , Jan, 2015 - 601 - J 6 Banna Conditions for Oscillation - • Two conditions: © Ahmad El 1. The phase shift around the feedback loop must be effectively 0°. 2. The voltage gain, Acl around the closed feedback loop (loop gain) must equal 1 (unity). 1448 Lec#12 , Jan, 2015 - 601 - J 7 Banna Start-Up Conditions - • For oscillation to begin, the voltage gain around the positive feedback loop must be greater than 1 so that the amplitude of the output can build up to a desired level.
[Show full text]
CLAPPS OSCILLATOR SHUBANGI MAHAJAN Indian Institute of Information Technology, Trichy
CLAPPS OSCILLATOR SHUBANGI MAHAJAN Indian Institute of Information Technology, Trichy INTRODUCTION Clapp oscillator is a variation Of Colpitts oscillator.The circuit differs from the Colpitts oscillator only in one respect; it contains one additional capacitor (C3) connected in series with the inductor. The addition of capacitor (C3) improves the frequency stability and eliminates the effect of transistor parameters and stray capacitances. Apart from the presence of an extra capacitor, all other components and their connections remain similar to that in the case of Colpitts oscillator. Hence, the working of this circuit is almost identical to that of the Colpitts, where the feedback ratio governs the generation and sustainability of the oscillations. However, the frequency of oscillation in the case of Clapp oscillator is given by fo=1/2π√L.C Where C=1/ (1/C1+1/C2+1/C3) Usually, the value of C3 is much smaller than C1 and C2. As a result of this, C is approximately equal to C3. Therefore, the frequency of oscillation, fo=1/2π√L.C3 Usually the value of C3 is chosen to be much smaller than the other two capacitors. Thus the net capacitance governing the circuit will be more dependent on it. A Clapp oscillator is sometimes preferred over a Colpitts oscillator for constructing a variable frequency oscillator. The Clapp oscillators are used in receiver tuning circuits as a frequency oscillator. These oscillators are highly reliable and are hence preferred inspite of having a limited range of frequency of operation. SCHEMATIC DIAGRAM Figure 1: Schematic diagram of clap oscillator NgSpice Plots: Figure 2: Output Plot PYTHON PLOT: Figure 3: output plot REFERENCES • https://www.tutorialspoint.com/sinusoidal_oscillators/sinusoidal_clapp_oscillat or.htm • https://www.electrical4u.com/clapp-oscillator/ .
[Show full text]
Sinusoidal and Non- Sinusoidal Oscillators
CHAPTER65 Learning Objectives ➣ What is an Oscillator? SINUSOIDAL ➣ Classification of Oscillators ➣ Damped and Undamped AND NON- Oscillations ➣ Oscillatory Circuit ➣ Essentials of a Feedback LC SINUSOIDAL Oscillator ➣ Tuned Base Oscillator ➣ Tuned Collector Oscillator OSCILLATORS ➣ Hartley Oscillator ➣ FET Hartley Oscillator ➣ Colpitts Oscillator ➣ Clapp Oscillator ➣ FET Colpitts Oscillator ➣ Crystal Controlled Oscillator ➣ Transistor Pierce Cystal Oscillator ➣ FET Pierce Oscillator ➣ Phase Shift Principle ➣ RC Phase Shift Oscillator ➣ Wien Bridge Oscillator ➣ Pulse Definitions ➣ Basic Requirements of a Sawtooth Generator ➣ UJT Sawtooth Generator ➣ Multivibrators (MV) ➣ Astable Multivibrator An oscillator is an electronic device used for ➣ Bistable Multivibrator (BMV) the purpose of generating a signal. Oscillators ➣ Schmitt Trigger are found in computers, wireless receivers ➣ Transistor Blocking Oscillator and transmitters, and audiofrequency equipment particularly music synthesizers 2408 Electrical Technology 65.1. What is an Oscillator ? An electronic oscillator may be defined in any one of the following four ways : 1. It is a circuit which converts dc energy into ac energy at a very high frequency; 2. It is an electronic source of alternating cur- rent or voltage having sine, square or sawtooth or pulse shapes; 3. It is a circuit which generates an ac output signal without requiring any externally ap- Oscillator plied input signal; 4. It is an unstable amplifier. These definitions exclude electromechanical alternators producing 50 Hz ac power or other devices which convert mechanical or heat energy into electric energy. 65.2. Comparison Between an Amplifier and an Oscillator As discussed in Chapter-10, an amplifier produces an output signal whose waveform is similar to the input signal but whose power level is generally high.
[Show full text]
Analog Circuits (EC-405) Unit : I Topic : Oscillator
Name of Faculty : Prof. L N Gahalod Designation : Associate Professor Department : Electronics & Communication Subject : Analog Circuits (EC-405) Unit : I Topic : Oscillator Analog Circuits (EC-405) Page 1 UNIT – I Feedback Amplifier and Oscillators 1.8 Oscillator: Any circuit that generates an alternating signal is called oscillator. To generate ac signal, the circuit is supplied energy from a dc source. The oscillators have variety of applications. In some application we need signal of low frequencies, in other of very high frequencies. For example, to test the performance of a stereo amplifier, we need an oscillator of variable frequency in audio range (20Hz – 20kHz), which is called audio frequency generator. Generation of high frequency is essential in all communication system. For example in radio and television broadcasting, the transmitter radiates the signal using a carrier of very high frequency. Some applications of communication system with their frequency band is given below. 550 kHz – 22 MHz Radio broadcasting 88 MHz – 108 MHz for FM radio 1 GHz – 4 GHz for DTH, TV and satellite Communication Figure 1.18: Block diagram of Oscillator Figure 1.18 shows that oscillator is an electronics source of alternating current or voltage having sine, square or saw tooth waves. Oscillator is a circuit which generates an ac source without requiring any externally applied input signal. It is a circuit which converts dc energy into ac energy at very high frequency. 1.9 Comparison between Amplifier and Oscillator: Comparision between an amplifier and an oscillator is explained in table 2. Analog Circuits (EC-405) Page 2 Amplifier Oscillator 1.
[Show full text]
Single Transistor Crystal Oscillator Circuits
Copyright © 2009 Rakon Limited SINGLE TRANSISTOR CRYSTAL OSCILLATOR CIRCUITS The majority of modern crystal oscillator circuits fall into one of two design categories, the Colpitts / Clapp oscillator and the Pierce oscillator. There are other types of single transistor oscillators ( Hartley and Butler for example ), but their usefulness and application is beyond the scope of this discussion. For an electronic circuit to oscillate there are two criteria which must be satisfied. It must contain an amplifier with sufficient gain to overcome the losses of the feedback network (quartz crystal in this case) and the phase shift around the whole circuit is 0 o or some integer multiple of 360 o. To design a crystal oscillator the above has to be true but there are a myriad of other considerations including crystal power dissipation, unwanted mode suppression, crystal loading (the actual impedance the crystal sees once oscillation has started) and the introduction of a non-linearity in the gain to limit the oscillation build-up. Consider the apparently simple circuit of the Colpitts / Clapp oscillator in Fig. 1. Without the correct simulation tools it is not immediately obvious this circuit has Negative Resistance at the frequency of oscillation (necessary to over come the crystals Equivalent Series Resistance), an initial gain in excess of one (to allow oscillator start- up) which drops to unity once the oscillation starts, and is then subsequently stabilised by either the voltage limiting on the transistor’s base emitter junction, or transistor collector current starvation. For AT cut crystals this circuit, with careful choice of the component values, can be made to oscillate from about 1MHz to above 200MHz with complete control over the crystal drive level and crystal loading impedance.
[Show full text]
Lecture 24: Oscillators. Clapp Oscillator. VFO Startup
Whites, EE 322 Lecture 24 Page 1 of 10 Lecture 24: Oscillators. Clapp Oscillator. VFO Startup Oscillators are circuits that produce periodic output voltages, such as sinusoids. They accomplish this feat without any “input” signal, other than dc power. Our NorCal 40A has three: 1. VFO (an LC oscillator), 2. BFO (a crystal oscillator), 3. Transmitter oscillator (also a crystal oscillator). You’ve likely had some experience with oscillators, perhaps with the astable multivibrator using the 555 IC. This RC oscillator produces a square-wave output voltage that is useful at low frequencies. Generally used in hobby-type circuits. The oscillators in the NorCal 40A are called feedback oscillators. This is a somewhat difficult subject since these oscillators are intrinsically nonlinear devices. Feedback oscillators have three basic parts: 1. An amplifier with signal gain G, 2. A linear feedback network with signal loss L, 3. A load of resistance R. We’ll ignore the effects of R for now. The amplifier and feedback network are connected as shown in Figure 11.1(a): © 2006 Keith W. Whites Whites, EE 322 Lecture 24 Page 2 of 10 amplifier G= gain x y L= loss linear feedback network For the amplifier y = Gx (11.1) y while for the feedback network xyLx= ⇒= (11.2) L Here we have two equations for two unknowns. However, these are not linearly independent equations! If • GL≠⇒== xy0. No oscillation is possible. • GL=⇒ y and x may not be zero. Hence, oscillation is possible. Generally, G and L are complex numbers, so we have two real equations to satisfy in the equality G = L: 1.
[Show full text]
5 Frequency Measurement and Manipulation
EE3.02/A04 Instrumentation 5. Frequency generation and measurement 5 Frequency Measurement and manipulation By the end of this section you will be able to: • Describe and quantify the operation of frequency measuring instruments. • Describe a phase locked loop, and its principles of operation. • Compute the centre frequency, capture and tracking range of a phase locked loop • Describe several methods for frequency multiplication. 5.1 Frequency as a state variable The generation and measurement of frequency is related to the ancient problem of determining time by building clocks. The importance of clocks to navigation on earth, on the sea and recently in air and in space means that enormous resources have been allocated over the centuries in resolving it. In our days time measurement is by far the most exact branch of metrology, and time is known (at least to the Standards organisations) with an estimated error of 1 part in 1014. Techniques to further improve time determination by another 2 orders of magnitude are known and are being implemented. Suffice it to say that the theoretical accuracy of time determined by GPS is better than 1 part in 108 which corresponds to an uncertainty of a fraction of a second /year. It is counter intuitive that the frequency of a signal can be considered as a state variable, a quantity which not only can be measured, but also can be manipulated. Figure 5-1: Historical development of clock accuracy (after HP application note 1289: The science of timekeeping) CP IC-EEE Autumn 2007 1 EE3.02/A04 Instrumentation 5.
[Show full text]
CHAPTER Feedback Amplifier & Oscillators
Analog Circuits Day-12 Oscillators Introduction to Feedback: The phenomenon of feeding a portion of the output signal back to the input circuit is known as feedback. The effect results in a dependence between the output and the input and an effective control can be obtained in the working of the circuit. Feedback is of two types. • Negative Feedback • Positive Feedback Negative or Degenerate feedback: • In negative feedback, the feedback energy (voltage or current), is out of phase with the input signal and thus opposes it. • Negative feedback reduces gain of the amplifier. It also reduce distortion, noise and instability. • This feedback increases bandwidth and improves input and output impedances. • Due to these advantages, the negative feedback is frequently used in amplifiers. NegativeFeedback Positive or regenerate feedback: • In positive feedback, the feedback energy (voltage or currents), is in phase with the input signal and thus aids it. Positive feedback increases gain of the amplifier also increases distortion, noise and instability. • Because of these disadvantages, positive feedback is seldom employed in amplifiers. But the positive feedback is used in oscillators. Positive Feedback In the above figure, the gain of the amplifier is represented as A. The gain of the amplifier is the ratio of output voltage Vo to the input voltage Vi. The feedback network extracts a voltage Vf = β Vo from the output Vo of the amplifier. This voltage is subtracted for negative feedback, from the signal voltage Vs. Now, Vi=Vs + Vf =Vs+βVo The quantity β = Vf/Vo is called as feedback ratio or feedback fraction. The output Vo must be equal to the input voltage (Vs + βVo) multiplied by the gain A of the amplifier.
[Show full text]
Investigation and Design of Low Phase Noise and Wideband Microwave Vcos
Investigation and Design of Low Improving landfill monitoring programs Phase Noise and Wideband Microwavewith the aid of VCOs geoelectrical - imaging techniques Master’sand geographical Thesis in Wireless and information Photonics Engineering systems Master’s Thesis in the Master Degree Programme, Civil Engineering MINHU ZHENG KEVIN HINE Department of Microtechnology and Nanoscience CHALMERSDepartment UofNIVERSITY Civil and Environmental OF TECHNOLOGY Engineering Goteborg,¨Division of Sweden GeoEngineering 2012 Engineering Geology Research Group CHALMERS UNIVERSITY OF TECHNOLOGY Göteborg, Sweden 2005 Master’s Thesis 2005:22 Investigation and Design of Low Phase Noise and Wideband Microwave VCOs © MINHU ZHENG, 2012 Master’s Thesis 2012 Department of Microtechnology and Nanoscience Chalmers University of Technology SE-41296 Goteborg¨ Sweden Tel. +46-(0)31 772 1000 Reproservice / Department of Microtechnology and Nanoscience Goteborg,¨ Sweden 2012 Investigation and Design of Low Phase Noise and Wideband Microwave VCOs Master’s Thesis in the Master's programme in Wireless and Photonics Engineering MINHU ZHENG Department of Microtechnology and Nanoscience Chalmers University of Technology Abstract This thesis studied the design techniques of low phase noise and wideband microwave voltage controlled oscillators (VCOs) used for point-to-point radio applications. First, basic oscillator theories as well as different technologies were reviewed. Then two C- band MMIC VCOs were designed in a commercial InGaP HBT foundry process with different topologies, namely the balanced Colpitts and the balanced Clapp. The circuits were simulated with a commercial harmonic balance simulator and the designs were optimized for the best phase noise performance by studying the implication of various design parameters, such as tank quality factors, transistor current density, feedback capacitor ratio and etc.
[Show full text]