Schedule of Unit Rates for Variation (M&E) Electrical

Total Page:16

File Type:pdf, Size:1020Kb

Schedule of Unit Rates for Variation (M&E) Electrical PROPOSED ADDITIONS AND ALTERATIONS WORKS FOR OFFICE OF FOOTBALL ASSOCIATION OF SINGAPORE @ 100 TYRWHITT ROAD, JALAN BESAR STADIUM, SINGAPORE 207542 SCHEDULE B - SCHEDULE OF UNIT RATES FOR VARIATION (M&E) Rates are inclusive of all overheads (including on and off-site supervisory staff, allowances, consumables, etc.) and shall remain valid until the end of the Defects Liability Period. ELECTRICAL Rate S$ Item Description Labour/ Total Unit Material Overheads/ Profits DISTRIBUTION BOARDS 1 Supply and installation of MCB distribution board complete with neutral and earth terminal block clamping rails, MCBs, etc., 63A and below incoming with 5A, 10A, No. of Ways (10KA) 15A or 20A Ways DP TPN DP TPN DP TPN DP TPN (a) 6 Ways (b) 8 Ways (c) 10 Ways (d) 12 Ways (e) 18 Ways (f) 24 Ways (g) 36 Ways (h) 48 Ways 40A and below incoming with 5A, 10A, No. of Ways (10KA) 15A or 20A Ways DP TPN DP TPN DP TPN DP TPN (a) 6 Ways (b) 8 Ways (c) 10 Ways (d) 12 Ways (e) 18 Ways (f) 24 Ways (g) 36 Ways (h) 48 Ways SCHEDULE B - 1 PROPOSED ADDITIONS AND ALTERATIONS WORKS FOR OFFICE OF FOOTBALL ASSOCIATION OF SINGAPORE @ 100 TYRWHITT ROAD, JALAN BESAR STADIUM, SINGAPORE 207542 Rate S$ Item Description Labour/ Total Unit Material Overheads/ Profits 2. MOULDED CASE CIRCUIT BREAKER/MINIATURE CIRCUIT BREAKER Supply and installation of MCB/ MCCB in cubicle panel complete with thermal/magnetic trip etc. Breaking Capacity of MCCB- 50KA rms (SYM) a) 415V, TPN (i) 100AF,60AT- 100AT 1 No (ii) 50AF,10AT- 50AT 1 No b) 415V, 4P (i) 100AF, 60AT- 100AT 1 No (ii) 50AF, 10AT- 50AT 1 No (c) 250V, DP (i) 100AF,60AT-100AT 1 No (ii) 50AF,10AT- 50AT 1 No Breaking Capacity of MCCB- 36KA rms (SYM) 415V, TPN (i) 100AF,60AT-100AT 1 No (ii) 50AF, 10AT-50AT 1 No 415V, 4P (i) 100AF,60AT-100AT 1 No (ii) 50AF, 10AT-50AT 1 No 250V, DP (i) 125AF,50AT-100AT 1 No (ii) 100AF,60AT-100AT 1 No (iii) 50AF,10AT- 50AT 1 No Breaking Capacity of MCCB- 22KA rms (SYM) 415V, TPN (i) 100AF,60AT-100AT (ii) 50AF, 10AT-50AT 1 No 415V, 4P SCHEDULE B - 2 PROPOSED ADDITIONS AND ALTERATIONS WORKS FOR OFFICE OF FOOTBALL ASSOCIATION OF SINGAPORE @ 100 TYRWHITT ROAD, JALAN BESAR STADIUM, SINGAPORE 207542 Rate S$ Item Description Labour/ Total Unit Material Overheads/ Profits (i) 1 No 100AF,60AT-100AT (ii) 50AF, 10AT-50AT 1 No 250V, DP (i) 100AF,60AT-100AT 1 No (ii) 50AF, 10AT-50AT 1 No Breaking Capacity of MCB15KA rms (SYM) (a) 415V, TPN (i) 100AF, 60AT- 100AT 1 No (ii) 50AF, 10AT- 50AT 1 No (b) 415V, 4P (i) 100AF, 60AT- 100AT 1 No (ii) 50AF, 10AT- 50AT 1 No (c) 250V, DP (i) 100AF,60AT-100AT 1 No (ii) 50AF,10AT- 50AT 1 No (d) 250V, SPN (i) 100AF,60AT-100AT 1 No (ii) 50AF,10AT- 50AT 1 No Breaking Capacity of MCB10KA rms (SYM) (a) 415V, TPN (i) 100A to 60A 1 No (ii) 50A to 15A 1 No (b) (iii) (c) 415V, 4P (i) 100A to 60A 1 No (ii) 50A to 15A 1 No (d) 250V, DP (i) 100AF,60AT-100AT 1 No (ii) 50AF,10AT- 50AT 1 No Item Description Rate S$ Total SCHEDULE B - 3 PROPOSED ADDITIONS AND ALTERATIONS WORKS FOR OFFICE OF FOOTBALL ASSOCIATION OF SINGAPORE @ 100 TYRWHITT ROAD, JALAN BESAR STADIUM, SINGAPORE 207542 Labour/ Unit Material Overheads/ Profits (e) 250V, SPN (i) 100AF,60AT-100AT (ii) 50AF,10AT- 50AT Breaking Capacity of MCB 6KA rms (SYM) (a) 415V, TPN (i) 100A to 60A 1 No (ii) 50A to 15A 1 No (b) 415V, 4P (i) 100A to 60A 1 No (ii) 50A to 15A 1 No (c) 250V, DP (i) 100AF,60AT-100AT 1 No (ii) 50AF,10AT- 50AT 1 No (d) 250V, SPN (i) 100AF,60AT-100AT 1 No (ii) 50AF,10AT- 50AT 1 No RESIDUAL CURRENT CIRCUIT BREAKERS 3. Supply and installation of current-operated residual current circuit breaker (RCCB) (a) 100mA sensitivity (i) 63A,4-pole,415V 1 No (ii) 40A,4-pole,415V 1 No (iii) 63A, 2-pole, 230V 1 No (iv) 40A, 2-pole, 230V 1 No (b) 30mA sensitivity (i) 63A,2-pole,250V 1 No (ii) 40A,2-pole,250V 1 No (iii) 63A, 4-pole, 415V 1 No (iv) 40A, 4-pole, 415V 1 No SCHEDULE B - 4 PROPOSED ADDITIONS AND ALTERATIONS WORKS FOR OFFICE OF FOOTBALL ASSOCIATION OF SINGAPORE @ 100 TYRWHITT ROAD, JALAN BESAR STADIUM, SINGAPORE 207542 Rate S$ Item Description Labour/ Total Unit Material Overheads/ Profits TIME SWITCHES / CONTACTORS 4. Supply and installation of 24 hour time switch with spring reserve and by-pass switch combination (a) 10A,SP,250V,50Hz 1 No (b) 16A,SP,250V,50Hz 1 No PVC, PVC/PVC, PVC/SWA/PVC CABLES 5. Supply and installation of PVC insulated cables (copper conductor) in steel trunking /conduit (excluding trunking/ conduit) (a) 1.0 sq mm/1C 1m (b) 1.5 sq mm/1C 1m (c) 2.5 sq mm/1C 1m (d) 4.0 sq mm/1C 1m (e) 6.0 sq mm/1C 1m (f) 10.0 sq mm/1C 1m (g) 16.0 sq mm/1C 1m (h) 25.0 sq mm/1C 1m (i) 35.0 sq mm/1C 1m (j) 50.0 sq mm/1C 1m 6. Supply and installation of PVC/PVC cables (copper conductor) on cable trays (excluding cable trays) (a) 1 x 10 sq mm/1C 1m (b) 1 x 16 sq mm/1C 1m (c) 1 x 25 sq mm/1C 1m (d) 1 x 35 sq mm/1C 1m (e) 1 x 50 sq mm/1C 1m SCHEDULE B - 5 PROPOSED ADDITIONS AND ALTERATIONS WORKS FOR OFFICE OF FOOTBALL ASSOCIATION OF SINGAPORE @ 100 TYRWHITT ROAD, JALAN BESAR STADIUM, SINGAPORE 207542 Rate S$ Item Description Labour/ Total Unit Material Overheads/ Profits CABLE TRUNKING/CONDUITS/ TRAYS/ LADDERS 7. Supply and installation of heavy duty underground pipes inclusive of excavation and backfilling, etc. (a) 50mm dia. uPVC 1m (b) 100mm dia. uPVC 1m 8. Supply and installation of surface heavy gauge galvanised screwed steel conduits and fittings (including fixing accessories) Size (a) 20mm dia 1m (b) 25mm dia 1m (c) 32mm dia 1m (d) 50mm dia 1m 9. Supply and installation of concealed heavy gauge galvanised screwed steel conduits and fittings (including fixing accessories) Size (a) 20mm dia 1m (b) 25mm dia 1m (c) 32mm dia 1m (d) 50mm dia 1m 10. Supply and installation of galvanised steel trunking complete with joints, cover plates and M.S. bracket supports Size (a) 50mm x 25mm 1m (b) 50mm x 50mm 1m (c) 75mm x 50mm 1m (d) 100mm x 50mm 1m (e) 100mm x 75mm 1m SCHEDULE B - 6 PROPOSED ADDITIONS AND ALTERATIONS WORKS FOR OFFICE OF FOOTBALL ASSOCIATION OF SINGAPORE @ 100 TYRWHITT ROAD, JALAN BESAR STADIUM, SINGAPORE 207542 Rate S$ Item Description Labour/ Total Unit Material Overheads/ Profits (f) 150mm x 100mm 1m (g) 200mm x 75mm 1m 11. Supply and installation of galvanised perforated steel cable trays/ladder complete with M.S. bracket supports Size (a) 50mm 1m (b) 100mm 1m (c) 150mm 1m (d) 200mm 1m (e) 300mm 1m (f) 450mm 1m 12. Supply and installation of hot- dipped galvanised mild steel cable tray/ladder complete with M.S. bracket supports Size (a) 50mm 1m (b) 100mm 1m (c) 150mm 1m (d) 200mm 1m 13. LIGHTING AND SMALL POWER Supply and installation of fluorescent light fittings complete with control gears, energy saving tube of colour rendering index 85% to 95% with colour temperature 3000K to 4000K. (All luminaires sizes shall be suitable for use with METRIC modular ceiling) (a) 20W COB LED surface mounted dimmable doen light, 3000K or 4000K, 1 No black finish (Diameter 170mm, height 230mm or approved equivalent SCHEDULE B - 7 PROPOSED ADDITIONS AND ALTERATIONS WORKS FOR OFFICE OF FOOTBALL ASSOCIATION OF SINGAPORE @ 100 TYRWHITT ROAD, JALAN BESAR STADIUM, SINGAPORE 207542 Rate S$ Item Description Labour/ Total Unit Material Overheads/ Profits (b) Eyelite 30W Led recessed dimmable down light with 1-10V dimmable LED driver c/w die cast 1 No housing aluminum trim with opal acrylic diffuser IP44 4000K 2400lm (c) Eyelite 30W Led recessed non dimmable down light LED driver c/w die cast 1 No housing aluminum trim with opal acrylic diffuser IP44 4000K 2400lm (d) 17.1W WFL COB wall washer LED light 3500K, white colour (135mm x 1 No 135mm, height 160mm) or approved equivalent (e) MARSON Tubular outdoor wall mounted with 2 x 11W LED light bulb 1 No (Bulb fitting E27) black finish IP65 (Diameter 9cm x Height 26cm). (f) EDITH candy holder wooden hanging lamp with 1 x 4/6W LED light bulb (Bulb fitting E27) 1 No white colour, (Width 120mm x Height 180mm x Depth 190mm), Material : Metal, glass , wood) (g) ELSA smooth metallic chic pot-lid pendant lamp with 1 x 4/6W LED light bulb (Bulb fitting E27) colour : Black/white/moss 1 No green, (Height of base 20cm, length of base 28cm) Material : Metal or approved equivalent (h) Emergency UFO lighting 1 No (i) Emergency “Mickey mouse” 1 No lighting SCHEDULE B - 8 PROPOSED ADDITIONS AND ALTERATIONS WORKS FOR OFFICE OF FOOTBALL ASSOCIATION OF SINGAPORE @ 100 TYRWHITT ROAD, JALAN BESAR STADIUM, SINGAPORE 207542 Rate S$ Item Description Labour/ Total Unit Material Overheads/ Profits 14. Supply and install the following emergency 'EXIT' light fitting: (a) 'EXIT' luminaires complete with 2 Nos. 8W fluorescent tube and gears with 2 hour 1 No Nickel cadmium re- chargeable battery (b) 'EXIT' luminairies with directional arrow complete with 2 Nos.
Recommended publications
  • Lecture 5: Electrical Supply and Distribution
    Lecture 5: Electrical Supply and Distribution 5.1 Single Phase Electric Power There is only one phase, i.e. the current flows through only one wire and there is one return path called neutral line to complete the circuit. Single-phase comes to the home with two wires: active and neutral. The neutral wire is connected to earth (water pipe, earth stake, etc.) at the switchboard. Single-phase distribution is used when loads are mostly lighting and heating, with few large electric motors. Single-phase power is: Able to supply ample power for smaller customers, including homes and small, non- industrial businesses. Adequate for running motors up to about 10kw; a single-phase motor draws significantly more current than the equivalent 3-phase motor, making 3-phase power a more efficient choice for industrial applications. 5.2 Three Phase Electric Power It is the Polyphase system where three phases are send together from the generator to the load. Each phase are having a phase difference of 120°, i.e. 120° angle electrically. Therefore, from the total of 360°, three phases are equally divided into 120° each. The power in three-phase system is continuous as all the three phases are involved in generating the total power. Three-phase has four wires: three actives (called phases) and one neutral. The neutral wire is earthed at the switchboard. 3-phase power is: Common in large businesses, as well as industry and manufacturing. Large domestic installations sometimes have three-phase because it distributes the total load in a way that ensures that the current in each phase is lower.
    [Show full text]
  • Answer the Purpose: 4
    Page 26 1. CONDUCTORS Conductors are defined as materials that easily allow the flow of _________. Metals are _______ conductors while insulators are ______ . The 2 common metals used for conductors in the electrical trade are: ___________ and ______________. Aluminium has become more prevalent for larger C.S.A. conductors as it is cheaper and lighter but more brittle than copper. Current/ Copper/ Aluminium Thermoplastic-sheathed cable (TPS) consists of an outer toughened sheath of polyvinyl chloride (PVC) (the thermoplastic element) covering one or more individual cables which are PVC insulated annealed copper conductors. It is a commonly used type of wiring for residential and light commercial construction in many countries. The flat version of the cable with two insulated conductors and an uninsulated earth conductor all within the outer sheath is referred to as twin and earth. In mainland Europe, a round equivalent is more common. Flat cables (or festoon cables) are made in PVC and Neoprene and are used as trailing cables for cranes, open filed conveyors and shelve service devices. Flat cables offer the advantages of extremely small bending radius’s, high flexibility and minimum wastage of space. Thermoplastic-sheathed cable (TPS) consists of an outer toughened sheath of polyvinyl chloride (PVC) (the thermoplastic element) covering one or more individual cables which are PVC insulated annealed copper conductors. It is a commonly used type of wiring for residential and light commercial construction in many countries. The flat version of the cable with two insulated conductors and an uninsulated earth conductor all within the outer sheath is referred to as twin and earth.
    [Show full text]
  • EDS 05-2010 Main Substation Feeder and Ring Main Unit Protection
    Document Number: EDS 05-2010 Version: 4.0 Date: 02/12/2015 ENGINEERING DESIGN STANDARD EDS 05-2010 VALIDITY BEFORE USE BEFORE VALIDITY MAIN SUBSTATION FEEDER AND RING MAIN UNIT S PROTECTION SETTINGS (LPN) Network(s): LPN Summary: This standard describes the protection settings for main substation feeders and ring main units in the LPN area. Owner: Kevin Burt Date: 02/12/2015 ADER MUST CONFIRM IT CONFIRM MUST ADER Approved By: Barry Hatton Approved Date: 08/01/2015 This document forms part of the Company’s Integrated Business System and its requirements are mandatory throughout UK Power Networks. Departure from these requirements may only be taken with the written approval of the Director of Asset Management. If you have any queries about this document please contact the author or owner of the current issue. Applicable To UK Power Networks External All UK Power Networks G81 Website Asset Management Contractors RE THE DOCUMENT, LED Capital Programme ICPs/IDNOs Connections Meter Operators HSS&TT Network Operations UK Power Networks Services Other THIS IS AN UNCONTROL AN IS THIS Document Number: EDS 05-2010 Version: 4.0 Date: 02/12/2015 E Revision Record Version 4.0 Review Date 08/01/2019 Date 02/12/2015 Author Kevin Burt Why has the document been updated – Periodic review What has changed – No content changes Document transferred onto a new template and rules applied S VALIDITY BEFORE US BEFORE VALIDITY S Version 3.2 Review Date 09/11/2015 Date 04/09/2012 Author Lee Strachan Document reviewed for publishing on G81 website Version 3.1 Review Date 09/11/2015 Date 25/08/2011 Author Chris Anderson Reclassified from EI to EDS Version 3.0 Review Date 09/11/2015 Date 19/08/2010 Author David G Edwards IT CONFIRM MUST ADER Rebranded, reviewed and review date extended Version 2.0 Review Date Date 30/10/2006 Author David G Edwards TLF ratings and revised ACB protection settings added Tables (6A and 11A) Version 1.0 Review Date Date 07/04/2004 Author David G Edwards Original, based on Protection Standard Number E 7/6 P 6/1 revision 4.
    [Show full text]
  • Pdf Grade 11 Physics Week 6 Lesson 2
    Ministry of Education Secondary Engagement Programme Grade 11 Physics WEEK 6 Lesson 2 Topic: Electricity Sub-topic: Electricity in Home Objective: Given information and with the aid of diagrams, students will: i. discuss the reasons for using parallel connections of domestic appliances; ii. explain the purpose of a fuse or circuit breaker and the earth wire; iii. select a fuse or circuit breaker of suitable current rating for a given appliance; iv. state the adverse effects of connecting electrical appliances to an incorrect or fluctuating voltage supply. Content: Distributing electricity Electrical energy is most efficiently generated and distributed using alternating current. Most Caribbean countries, and also the USA, utilize an a.c. frequency of 60 Hz. A few territories use a frequency of 50 Hz. Minimizing Power Loss When current travels along a wire, the wire becomes hot and heat energy is lost to the atmosphere. Power is lost according to the formula P = I2 R where P is the power lost, I is the current in the wire and R is the resistance of the wire To minimize power loss, two approaches are used in distribution systems. i. Keep the resistance (R) of the conducting wires as small as possible. The transmission wires, therefore, have larger diameters, since thick wires have less resistance per unit length than thin wires. ii. A second approach is to use small currents in the wires. To achieve this, the power is sent at very high voltages. Household electric circuits Parallel wiring 68 Ministry of Education Secondary Engagement Programme Grade 11 Physics Parallel wiring is used in household circuits rather than series connections so that appliances can be controlled individually without affecting other devices.
    [Show full text]
  • The Testing of Electrical Installations
    2014 HellermannTyton South Africa Compliance Testers Compliance Test Kits TCTRP TCTDT TCTCDK Description Analogue Digital Digital Kit Kit Kit DMM TBM811 - - Clamp Meter - TBM3030 TBM3030 Insulation Tester T1800 T1851 T1151 Earth Resistance T1805 T1820 T1120 Loop Tester T1825 T1825 T1125 ELCB Tester TEL1TLB TEL1TLB TEL1TLB Phase Rotation T860 T887 T890 Foam TCTRPFM TCTDTFM TCTCDKFM Case TCTCS TCTCS TCTCS Refer to pages 19-24 for Technical Specifications Compliance Combination Tester Model T419 | T89 All the above testers featured in a single lightweight compliance combination tester • Continuity (Low OHM) • Insulation (50/100/250/500/1000 V) • Loop impedance • Earth resistance (resistivity) • ELCB (sensitivity & time) • RS232 Interface or USB • Frequency/Voltage • Phase Rotation • 350 Memory Locations Johannesburg Durban Cape Town Port Elizabeth i (011) 879-6620 (031) 569-9900 (021) 594-7100 (041) 408-2400 Index 1. WHAT IS AN ELECTRICAL INSTALLATION? 1 2. WHO IS RESPONSIBLE? 1 3. HOW CAN A LAYMAN KNOW IF THE INSTALLATION IS SAFE? 1 4. WHERE TO OBTAIN A CERTIFICATE OF COMPLIANCE? 1 5. WHAT MUST BE DONE BEFORE ISSUING A CERTIFICATE OF COMPLIANCE? 1 6. WHAT ELECTRICAL TEST MUST BE CARRIED OUT? 1 Tests to be done 7. CONTINUITY OF ALL BONDING CONDUCTORS 1/2 8. RESISTANCE OF EARTH CONTINUITY CONDUCTOR 2 9. CONTINUITY OF RING CIRCUIT (IF APPLICABLE) 4 10. ISOLOCK TESTER 5 11. EARTH LOOP IMPEDANCE TEST: MAIN SWITCH 4/6 12. ELEVATED VOLTAGE ON NEUTRAL 10 13. EARTH ELECTRODE RESISTANCE (IF REQUIRED) 10 14. INSULATION RESISTANCE 14 15. VOLTAGE (MAIN DB) NO LOAD 14 16. VOLTAGE (MAIN DB) ON LOAD 14 17. VOLTAGE AT AVAILABLE LOAD (WORST CONDITION) 14 18.
    [Show full text]
  • Huawei Data Center Facilities Solutions
    Power ICT in a Smart Way Huawei Data Center Facilities Solutions HUAWEI TECHNOLOGIES CO., LTD. Contents Modular Data Center ���������������������������������������������������������������� 05 Prefabricated Data Center �������������������������������������������������������� 17 Huawei Datacenter Facility Management System ��������������������� 29 Global Applications ������������������������������������������������������������������� 31 Indoor Modular Data Center FusionModule2000&5000 FusionModule800 Outdoor Prefabricated Data Center FusionModule1000B FusionModule1000A Modular Data Center FusionModule5000 Smart Modular Data Center Introduction HUAWEI FusionModule5000 is a new generation smart modular data center solution with complete integration of cabinets, power supply and distribution systems, cooling systems, cabling systems, management software, and other subsystems. It supports flexible deployment with single or dual row, cold or hot aisle containment. The maximum IT power can be up to 21kW/rack. Application Scenarios • Maximum IT power per module can be up to 310kW, which meet FusionModule5000 (Dual-row) the requirements of large-scale data center for industries like ISP, government, education, healthcare, finance, telecom, etc. • Designed for chilled water cooling scenarios. Features & Value Reliable • Single/dual power supply, Tier IV supportive, Precise monitoring of power branch temperature prevents fire caused by loose contact and overheat • Water leakage monitoring keeps room away from flooding • Ring network of monitoring system
    [Show full text]
  • House Wiring and Dirty Electricity
    Your low EMF Home 1. House wiring © Alasdair and jean Philips 2.11.17 Your low EMF Home Articles Your low EMF Home set of articles is separated into 9 sections, each of which can be individually downloaded. It is a 'work in progress' incorporating new information whenever time permits. Section 1 House wiring and EMFs; July 2007 SAGE report 1. House wiring and EMFs; introduction; what are normal EMFs? Choosing a consumer unit; electric fields; cables; demand switches; external ‘faults’ in the supply that can cause high magnetic fields; Wiring in homes - SAGE report July 2007 2. Dirty electricity (DE) – What is dirty electricity? What effect does it have? What sort of levels are you likely to have? What you can do if you have high levels of DE; DE coming into the house; DE generated within the house; dLAN caution 3. Lighting and EMFs; Bulbs, incandescent, energy-saving, fluorescent, halogen, full- spectrum light, daylight, light emitting diode (LED); anglepoise lamps and other metal framed lamps, halogen desk lamps, bedside/bedhead lights, spotlights, standard lamps and table lamps, nightlights; light wiring; light switches, dimmer switches; Physiological effects of blue and red lights; circadian rhythms, melatonin, light and illness, timing of blue lights, timing of red/amber lights 4. Smart meters – What is it all about? Smart Grid; Remote reading meters; Smart meters; Wide Area Network (WAN) technologies; Home Area Network (HAN); RF exposures from Smart Meters; Experiences of smart meters in other countries; Solar storms may affect smart
    [Show full text]
  • Hybrid Ring/Radial Final Circuits
    PE NICEIC OCTober 2015:Layout 1 06/08/2015 15:13 Page 1 TECHNICAL ADVICE taking you step by step through procedures and requirements for electrical installations Hybrid ring/radial final circuits ICEIC is sometimes asked whether a ring Ring circuit cable (installed rating 20 A min) final circuit has to be Nsupplied directly from Ring !nal circuit a protective device in the distribution board or consumer unit, or whether it is permitted to supply the two ends of the Junction box (or possibly double-pole switch or contactor) rated at 30/32 A min ring via a dedicated radial circuit Cable connected to 30/32 A overcurrent protective device Radial circuit cable cable, as shown in Fig. 1, in consumer unit (installed rating 30/32 A min) thereby forming a hybrid L OUT N ring/radial circuit. OUT This question can arise where, for example, the contractor wishes to Consumer unit make use of a redundant radial circuit cable previously installed for another Fig 1 Typical ring final circuit supplied via a radial circuit cable, purpose (such as a cooker circuit) to forming a hybrid ring/radial circuit supply a ring final circuit, or where a Periodic Inspection of an existing hybrid circuit, the ‘single point of of the socket-outlets ( I⌬n ≤ 30 mA) in installation reveals such an supply’ is the point at which the two accordance with Regulation 411.3.3. arrangement. ends of the ring part of the circuit are Also, if any part of the circuit cable connected to the radial part (that is, at The same question may also arise is concealed in a wall or partition, it the junction box, switch or contactor as where the contractor wishes to control must be provided with additional labelled in Fig 1).
    [Show full text]
  • Switch Pdf, Epub, Ebook
    SWITCH PDF, EPUB, EBOOK Megan Hart | 376 pages | 10 Aug 2012 | Harlequin (UK) | 9780263904536 | English | Richmond, United Kingdom Switch PDF Book The knife and contacts are typically formed of copper , steel , or brass , depending on the application. English Now I'm going to ask you again to switch on the emotional bit. Koei Tecmo America Corpor; Koei. A biased switch contains a mechanism that springs it into another position when released by an operator. A pair of contacts is said to be " closed " when current can flow from one to the other. Contact materials are also chosen on the basis of electrical conductivity , hardness resistance to abrasive wear , mechanical strength, low cost and low toxicity. Modus Games. Demand response Distributed generation Dynamic demand Electric power distribution Electricity retailing Electrical busbar system Electric power system Electric power transmission Electrical grid Electrical interconnector High-voltage direct current High-voltage shore connection Load management Mains electricity by country Power line Power station Power storage Pumped hydro Smart grid Substation Single-wire earth return Super grid Transformer Transmission system operator TSO Transmission tower Utility pole. Temp Brand. Product Variants Selector. The interior lamp of a household refrigerator is controlled by a switch that is held open when the door is closed. Your feedback helps us make Walmart shopping better for millions of customers. Do you know the person or title these quotes desc USA Gear. The terms " make " for closure of contacts and " break " for opening of contacts are also widely used. Login or Register. For example, the caps lock key on a computer causes all letters to be generated in capitals after it is pressed once; pressing it again reverts to lower-case letters.
    [Show full text]
  • High Resistance Fault Locator Refer to Preface & Safety Instructions Before Operating Applicable from Serial No
    T272 High Resistance Fault Locator Refer to Preface & Safety Instructions before operating Applicable from serial no. 37888 onwards Operation Manual l Issue 5 l September 2008 00901183-5 T272 Operating Manual Contents 1. Health and Safety at Work.............................................................................................. 1 3. Technical Specification................................................................................................... 2 4. Connections..................................................................................................................... 2 Connections both ends available - ...................................................................................... 3 Operation............................................................................................................................. 6 Copyright 2008 Radiodetection Ltd - SPX Corporation. All rights reserved. Radiodetection is a subsidiary of SPX Corporation. SPX and Radiodetection are trademarks of Radiodetection Ltd. and SPX Corporation. Due to a policy of continued development, we reserve the right to alter or amend any published specification without notice. Copyright 2008 Radiodetection Ltd - SPX Corporation. This document is protected by copyright and may not be copied, reproduced, transmitted, modified or used, in whole or in part, without the prior written consent of Radiodetection Ltd. Radiodetection Ltd. 00901183-5 T272 Operating Manual Page 1 1. Health and Safety at Work 1.1 Health And Safety At Work Act 1974
    [Show full text]
  • Ch34 Switchgear
    //integras/b&h/Eer/Final_06-09-02/eerc034 34 Switchgear B M Pryor DipEE, CEng, FIEE Power Systems Consultant Substations & Main Plant Contents 34.1 Circuit-switching devices 34/3 34.1.1 Disconnectors (isolators) 34/3 34.5 HV secondary distribution switchgear 34/27 34.1.2 Switches 34/3 34.5.1 Urban networks 34/27 34.1.3 Switch disconnectors 34/4 34.5.2 Rural networks 34/29 34.1.4 Earth switches 34/4 34.1.5 Fuses 34/5 34.6 HV primary distribution switchgear 34/29 34.1.6 Fuse switches 34/10 34.1.7 Contactors 34/12 34.7 HV transmission switchgear 34/29 34.1.8 Circuit-breakers 34/13 34.8 Generator switchgear 34/30 34.2 Materials 34/19 34.2.1 Insulating materials 34/19 34.9 Switching conditions 34/31 34.2.2 Contact materials 34/21 34.9.1 Normal switching conditions 34/31 34.9.2 Abnormal switching conditions 34/33 34.3 Primary-circuit-protection devices 34/21 34.3.1 Current transformers 34/22 34.10 Switchgear testing 34/34 34.3.2 Voltage transformers 34/22 34.3.3 Combined-instrument transformers 34/24 34.11 Diagnostic monitoring 34/35 34.3.4 Surge arresters 34/24 34.12 Electromagnetic compatibility 34/35 34.4 LV switchgear 34/25 34.4.1 Fuse cut-outs 34/25 34.13 Future developments 34/35 34.4.2 LV fuse cabinets 34/26 34.4.3 LV switchboards 34/27 //integras/b&h/Eer/Final_06-09-02/eerc034 //integras/b&h/Eer/Final_06-09-02/eerc034 Circuit-switching devices 34/3 `Switchgear' is a term used to refer to combinations of Disconnectors are generally hand operated but may have switching devices and their interconnection with associated power operating mechanisms if remote operational facilities control, protective and measurement systems.
    [Show full text]
  • Socket Outlets, Light Switches, Power Points, Clock Connectors, Cooker Control Units and Similar Outlets
    Electrical Installation Lecture No.12 Dr.Mohammed Tawfeeq Al-Zuhairi Accessories INTRODUCTION From the user’s point of view the electricity service in a building consists of socket outlets, light switches, power points, clock connectors, cooker control units and similar outlets. Such fittings are collectively known as accessories. SOCKET OUTLETS A socket outlet is the correct name of what is popularly known as a power point. It is a female socket connected to the power wiring in the building and will accept the male plug attached at the end of the flexible wire of an appliance such as a vacuum cleaner, electric fire or music centre.They are rated at 2 A, 5 A.13A and 15A, the spacing of the pins and sockets being different for the different ratings. This makes sure that a plug of one rating cannot be inserted, even wilfully, into a socket of a different rating. Plugs and sockets rated at 2 and 5 A are available in both two- and three-pin versions, but those of 15 A rating are made only with three pins. Types of Domestic plugs and sockets Type A (North America/Japanese 2-pin) Type B (American 3-pin) 1 Electrical Installation Lecture No.12 Dr.Mohammed Tawfeeq Al-Zuhairi Type C (European 2-pin) (Type D – German 2-pin ) Type E (French 2-pin , female earth) 2 Electrical Installation Lecture No.12 Dr.Mohammed Tawfeeq Al-Zuhairi Type F ( British 3- pin) Duplex British 3 – pin ( type –F) Type G (Danish 3-pin ) 3 Electrical Installation Lecture No.12 Dr.Mohammed Tawfeeq Al-Zuhairi BS 546 (15 A/250 V earthed) Type of connection of socket outlets circuits 1.
    [Show full text]