DOCSLIB.ORG

High-Pressure-Assisted Heating As a Method for Sterilizing Foods

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
High-Pressure-Assisted Heating As a Method for Sterilizing Foods 10 High-Pressure-Assisted Heating as a Method for Sterilizing Foods Volker Heinz and Dietrich Knorr Technical University Berlin, Berlin, Germany I. INTRODUCTION In 1899, Hite (1899) subjected milk to high hydrostatic pressure instead of high temperature to keep it from turning sour. His attempt was inspired by the sensory shortcomings of heat- sterilized milk, which had a ‘‘cooked’’ taste, and by his knowledge of recent discoveries in the field of marine ecology, in which researchers had demonstrated that microorganisms are affected by pressure. Hite achieved a 4-log reduction in microbial count in milk with a 10- min treatment at approximately 700 MPa at room temperature. A 30-min treatment at 400 MPa successfully preserved grape juice, cider, peaches, and pears without destroying the fresh flavor. Below 200 MPa, the lethal effect of pressure was found to be significantly reduced, which was in agreement with earlier findings of Chlopin and Tammann (1903). These authors already reported the resistance of bacterial spores to hydrostatic pressure, which was later proven by Larson et al. (1918). These authors found that a pressure of even 1200 MPa was not sufficient to kill Bacillus subtilis spores. Shortly afterward, Bigelow published his data (Bigelow et al., 1920, 1921), and for the first time, a scientifically based method and calculation procedure for heat sterilization of food was introduced. In these publications, the effectiveness of heat treatment was proven by quantifying the death of the bacterial spores responsible for product deterioration or foodborne illnesses. Clear processing rules were developed that accounted for the transient nature of heat transfer. It is evident that the lack of success in spore inactivation impaired the quality-retaining benefits of high hydrostatic pressure as an alternative preservation treatment. The production of shelf-stable food was (and still is) the goal of the canning industry. From the viewpoint of a process engineer, it is understandable that the optimization of thermal preservation appeared to be more promising. In fact, the development of rotary retort systems, high-temperature–short-time treatment, aseptic processing, and novel pack- aging systems improved the quality characteristics of thermally processed food substan- tially. However, due to physical limitations, a certain class of products can be identified that warrants further consideration on the effectiveness of heat treatments. In this chapter, it will be demonstrated that high pressure can be used beneficially in those situations where conventional thermal sterilization processes fail to obtain high-quality products. 207 Copyright © 2005 by Marcel Dekker. 208 Heinz and Knorr II. PRESSURE AND TEMPERATURE Thermodynamic properties and phase equilibria in any system, as well as transport properties such as viscosity, thermal conductivity, or diffusivity, must be considered in their functional relationship with temperature and pressure. The equilibrium concentrations of chemical reactions also depend on these quantities. From experiments, it is known that the formation of ions from neutral molecules, like the self-ionization of water, is promoted by increasing pressure. Applying the ‘‘Le Chatelier’’ principle to the resulting drop in pH, it can be assumed that the volume of the ions is less than the volume of the neutral molecules. In general, the impact of pressure ( p) and temperature (T) can be derived quantitatively from Gibbs’s definition of free energy G [Eq. (1)]: GuH À TS ð1Þ where S and H are the entropy and enthalpy, respectively. Using HuU+pV (U: inner energy; V: volume), the total derivative of Eq. (1) yields: dG ¼ dU þ pdV þ Vdp À TdS À SdT ð2Þ This converts to Eq. (3) when the First and Second Laws of Thermodynamics (dUudqÀpdV and dquTdS, where dq denotes the transferred heat) are applied and when only changes in free energy (DG) are considered: dðDGÞ¼DVdp À DSdT ð3Þ From Eq. (3), it follows that transitions or reactions within physicochemical systems that show a difference in free energy between educts and products are determined by simultaneously occurring changes in volume and entropy. Hence, reactions such as phase transitions or molecular reorientation depend on both temperature and pressure and cannot be treated separately. Integration of Eq. (3) using a Taylor series expansion up to second- order terms yields Eq. (4): 2 2 DG ¼ DG0 þ DV0ð p À p0ÞDS0ðT À T0ÞþðDb=2Þðp À p0Þ ðDcp=2T0ÞðT À T0Þ þDað p À p0ÞðT À T0Þð4Þ with a u (dV/dT)p: thermal expansion coefficient; b u (dV/dp)T: compressibility; and cp u (dq/dT)p: heat capacity. It is evident that this approximation yields a quadratic dependence of the change in free energy on temperature and pressure. In Fig. 1, it is demonstrated that this quadratic two-variable function converts to an ellipsoidal phase transition line in the p–T plane for constant DG. In the diagram on the right, a particular situation where DG=0 is considered for the relevant pressure and temperature range ( p z 0andT z 0). Usually, states A and B denote molecular or physicochemical states, which are reversibly or irreversibly connected by reactive pathways that finally bring about the transition to the energetically favored configuration (DG<0). In a more general approach, this concept may also apply to the inactivation of spores. In spite of the limited knowledge on the mechanistic background of the lethal action, it is clear that biochemical reactions sensitive to changes in pressure and temperature are involved. Hence, it is still a matter of speculation whether only one or multiple target sites of the sporulated organism should be regarded as the weakest link when exposed to external stress; from the point of view of preservation technology, these considerations are of less importance. Therefore, it is justified at this point to reduce the Copyright © 2005 by Marcel Dekker. High-Pressure Heating for Sterilizing Foods 209 Figure 1 Changes in free energy in response to pressure and temperature. highly complex survival strategy of bacterial spores (described later in this chapter) to two distinct states: recoverable and not recoverable. In analogy to states A and B in Fig. 1, it can be assumed that the inactivation can be brought about at various pressure–temperature conditions along the equilibrium line DG=0. From the relations given above, the rate at which the spore alters from the recoverable to the nonrecoverable state cannot be deduced. This is because the thermodynamic formulations are based on the assumption that during transition, all components involved are equilibrated, which takes an infinitely long time theoretically. In fact, the kinetics of reactive pathways must be treated in a different way. For process engineering, it is most important to know which treatment time is required to obtain the expected results, and how the process is influenced by changes in pressure and temperature. The velocity of chemical reactions can be accelerated as well as delayed by variations in pressure and/or temperature. This effect is highly dependent on the molecules involved and the reaction mechanism under consideration. In order to find a quantitative formulation of this observation, the reaction rate (k) must be related to these parameters. Whereas a reliable relation on the temperature dependence of k was first published in 1889 by Arrhenius (1889) [Eq. (5)], it took much longer until a similar expression for pressure dependence [Eq. (6)] was derived by Eyring (1935a,b) in 1935. BlnðkÞ E ¼ a ð5Þ BT RT 2 p BlnðkÞ DV Ã B ¼ ð6Þ p T RT with R: universal gas constant (R = 8.314 J/K mol); Ea: activation energy; and DV*: activation volume. Observing the right-hand side of Eq. (6), it is evident that a negative DV produces an increased reaction rate k, whereas a positive DV * indicates a delayed reaction. Examples of accelerated reactions can be found among polymerizations, cyclo-additions, and solvolytic reactions. Unfortunately, the general application of Eq. (6) is hindered by the empirical finding that DV * is not always constant, but may also vary with pressure. Another limitation is that the order of reaction might be different at different pressure levels [which is not considered in Eq. (6)]. Copyright © 2005 by Marcel Dekker. 210 Heinz and Knorr From Eqs. (5) and (6), it is obvious that experimental designs must include both pressure and temperature in the set of independent variables. Hence, systematic inves- tigations of any pressure–temperature response of a system are based on kinetic experiments at constant pressure and temperature to identify the reaction order or, possibly, the underlying mechanism of action of a more complex response. An obvious way of showing the results of such experiments is to use a contour plot with lines of constant reaction rate k in a p–T diagram similar to that of Fig. 1. The importance of these results is even more relevant when the thermodynamic relation between pressure and temperature must be taken into account. If the boundary of a system under consideration is assumed adiabatic, and if phase transitions are excluded, an increase in pressure will produce a rise in temperature. The effect of compression on aqueous systems is presented in Fig. 2. This observation can be expressed by the thermodynamically derived Eq. (7), where q denotes the density of the system. In most cases, unfortunately, the thermal expansion coefficient and the specific heat capacity are not constant within the temperature and pressure range, which is of interest, and little experimental data on food materials are available. BT aT B ¼ ð7Þ P adiabat pcp It is important to note that the temperature increase DT under adiabatic conditions depends on the maximum pressure reached, as well as on the temperature of the system before compression. For example, a pressurization of water from ambient pressure up to 800 MPa with an initial temperature of 5jC and 100jC results in a level of 23jC and 140jC, respectively.
Load more

Recommended publications
  • Heat Resistant Thermophilic Endospores in Cold Estuarine Sediments
    Heat resistant thermophilic endospores in cold estuarine sediments Emma Bell Thesis submitted for the degree of Doctor of Philosophy School of Civil Engineering and Geosciences Faculty of Science, Agriculture and Engineering February 2016 Abstract Microbial biogeography explores the spatial and temporal distribution of microorganisms at multiple scales and is influenced by environmental selection and passive dispersal. Understanding the relative contribution of these factors can be challenging as their effects can be difficult to differentiate. Dormant thermophilic endospores in cold sediments offer a natural model for studies focusing on passive dispersal. Understanding distributions of these endospores is not confounded by the influence of environmental selection; rather their occurrence is due exclusively to passive transport. Sediment heating experiments were designed to investigate the dispersal histories of various thermophilic spore-forming Firmicutes in the River Tyne, a tidal estuary in North East England linking inland tributaries with the North Sea. Microcosm incubations at 50-80°C were monitored for sulfate reduction and enriched bacterial populations were characterised using denaturing gradient gel electrophoresis, functional gene clone libraries and high-throughput sequencing. The distribution of thermophilic endospores among different locations along the estuary was spatially variable, indicating that dispersal vectors originating in both warm terrestrial and marine habitats contribute to microbial diversity in estuarine and marine environments. In addition to their persistence in cold sediments, some endospores displayed a remarkable heat-resistance surviving multiple rounds of autoclaving. These extremely heat-resistant endospores are genetically similar to those detected in deep subsurface environments, including geothermal groundwater investigated from a nearby terrestrial borehole drilled to >1800 m depth with bottom temperatures in excess of 70°C.
    [Show full text]
  • Food Processing and Preservation - Sbt1607
    SCHOOL OF BIO AND CHEMICAL ENGINEERING DEPARTMENT OF BIOTECHNOLOGY B.TECH – BIOTECHNOLOGY UNIT – I - FOOD PROCESSING AND PRESERVATION - SBT1607 HISTORY OF FOOD PROCESSING AND FOOD PRESERVATION FOOD PROCESSING Food processing dates back to the prehistoric age when crude processing including various types of cooking, such as over fire, smoking, steaming, fermenting, sun drying and preserving with salt were in practice. Foods preserved this way were a common part of warriors’ and sailors’ diets. These crude processing techniques remained essentially the same until the advent of the Industrial Revolution. Nicolas Appert developed a vacuum bottling process to supply food to troops in the French army, which eventually led to canning in tins by Peter Durand in 1810. Modern food processing technologies, in the 19th century were also largely developed to serve military needs. In the early 20th century, the space race, change in food habits and the quality conciousness of the consumers in the developed world furthered the development of food processing with advancements such as spray drying, juice concentrates, freeze drying and the introduction of artificial sweetners, colourants, and preservatives. In the late 20th century products including dried instant soups, reconstituted fruit juices, and self cooking meals such as ready-to-eat food rations etc., were developed. Benefits of Processing . Converts raw food and other farm produce into edible, usable and palatable form. Helps to store perishable and semi-perishable agricultural commodities, avoid glut in the market, check post harvest losses and make the produce available during off-season. Generates employment. Development of ready-to-consume products, hence saves time for cooking.
    [Show full text]
  • Medical Bacteriology
    LECTURE NOTES Degree and Diploma Programs For Environmental Health Students Medical Bacteriology Abilo Tadesse, Meseret Alem University of Gondar In collaboration with the Ethiopia Public Health Training Initiative, The Carter Center, the Ethiopia Ministry of Health, and the Ethiopia Ministry of Education September 2006 Funded under USAID Cooperative Agreement No. 663-A-00-00-0358-00. Produced in collaboration with the Ethiopia Public Health Training Initiative, The Carter Center, the Ethiopia Ministry of Health, and the Ethiopia Ministry of Education. Important Guidelines for Printing and Photocopying Limited permission is granted free of charge to print or photocopy all pages of this publication for educational, not-for-profit use by health care workers, students or faculty. All copies must retain all author credits and copyright notices included in the original document. Under no circumstances is it permissible to sell or distribute on a commercial basis, or to claim authorship of, copies of material reproduced from this publication. ©2006 by Abilo Tadesse, Meseret Alem All rights reserved. Except as expressly provided above, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording, or by any information storage and retrieval system, without written permission of the author or authors. This material is intended for educational use only by practicing health care workers or students and faculty in a health care field. PREFACE Text book on Medical Bacteriology for Medical Laboratory Technology students are not available as need, so this lecture note will alleviate the acute shortage of text books and reference materials on medical bacteriology.
    [Show full text]
  • Unit 3 Lecture 6
    Unit 3 Lecture 6 Unit 3 Lecture 6 Introduction to Antimicrobials An Antimicrobial is any method which interferes with the optimum growth of a microbe. Microbial death is defined as the inability of the organism to reproduce. Sterility is the complete destruction or removal of all microorganisms and viruses. Sterile is an absolute term. There is no “almost sterile.” Sterility requires all life forms to be eliminated from the various kingdoms of microorganisms including the vegetative state (those in active metabolism and reproduction) and those that are quite resistant to sterilization (e.g. endospores and cysts). Sterilization can be achieved by physical or chemical means. Microbial death is the permanent loss of reproductive ability of the microbe. Disinfection is the complete destruction or removal of all vegetative pathogens and their toxins. It does not affect endospores. Therefore non- pathogenic life forms may survive. It does however require all vegetative forms of pathogens be eliminated. Disinfection can be achieved by physical or chemical means. A disinfectant is used on only on inanimate objects. Aseptic techniques Surgical asepsis is any barrier to exclude the admission of any viable organism. Medical asepsis is any barrier to exclude the admission of naturally communicable organisms. An Antiseptic is a chemical used to provide asepsis that is safe to use on body surfaces. An object or skin is sanitized when the mechanical destruction or removal of sufficient microbes has been performed to have a microbial population at a “safe level.” Degermation is the reduction of the number of microbes on the skin by scrubbing. Word parts used with antimicrobials that assist in their definition.
    [Show full text]
  • Self Assessment & Review: Microbiology & Immunology, 4Th
    Self Assessment & Review MMUNOLOGY Self Assessment & Review MMUNOLOGY 4th Edition Rachna Chaurasia MD Radiodiagnosis MLB Medical College, Jhansi, India Anshul Jain MD Anaesthesia MLB Medical College, Jhansi, India the arora medical book publishers pvt. ltd. A Group of Jaypee Brothers Medical Publishers (P) Ltd. Published by Jitendar P Vij Jaypee Brothers Medical Publishers (P) Ltd Corporate Office 4838/24 Ansari Road, Daryaganj, New Delhi - 110002, India, Phone: +91-11-43574357 Registered Office B-3 EMCA House, 23/23B Ansari Road, Daryaganj, New Delhi - 110 002, India Phones: +91-11-23272143, +91-11-23272703, +91-11-23282021, +91-11-23245672 Rel: +91-11-32558559, Fax: +91-11-23276490, +91-11-23245683 e-mail: [email protected], Website: www.jaypeebrothers.com Branches ❑ 2/B, Akruti Society, Jodhpur Gam Road Satellite Ahmedabad 380 015, Phones: +91-79-26926233, Rel: +91-79-32988717 Fax: +91-79-26927094, e-mail: [email protected] ❑ 202 Batavia Chambers, 8 Kumara Krupa Road, Kumara Park East Bengaluru 560 001, Phones: +91-80-22285971, +91-80-22382956 91-80-22372664, Rel: +91-80-32714073, Fax: +91-80-22281761 e-mail: [email protected] ❑ 282 IIIrd Floor, Khaleel Shirazi Estate, Fountain Plaza, Pantheon Road Chennai 600 008, Phones: +91-44-28193265, +91-44-28194897 Rel: +91-44-32972089, Fax: +91-44-28193231, e-mail: [email protected] ❑ 4-2-1067/1-3, 1st Floor, Balaji Building, Ramkote Cross Road, Hyderabad 500 095, Phones: +91-40-66610020, +91-40-24758498 Rel:+91-40-32940929Fax:+91-40-24758499, e-mail: [email protected]
    [Show full text]
  • 201: Microbiology UNIT –I
    201: Microbiology UNIT –I 1. Beginning of Microbiology, milestones in the development of microbiology, spontaneous generation, Microbial Ecosystem, Microbial world, Branches of Microbiology, Application of microbiology. 2. Methods in Microbiology: Sterilization, Culture Media, Pure culture technique, enrichment culture technique, Microbial staining methods, Maintenance and preservation of Microorganisms, Culture collection centers. 3. Microbial growth: Growth curve, measurement of growth, growth yields, synchronous growth, continuous culture, growth as affected by environmental factors such as temperature, acidity, alkalinity, water availability and oxygen. 4. Microbial evolution, systematics and taxonomy: Evolution of earth’s earliest life forms, primitive organisms, their metabolic strategies and their molecular coding, New approaches to bacterial taxonomy, nomenclature, Bergey’s manual, Ribotyping. NOTES Discovery of Microscope: The fascinating microbial world would have remained unknown had the microscope not been invented. It was Roger Bacon (1267) who developed a lens for the first time. Jansen and Jansen (1590), about 300 years later first produced a crude type of microscope by placing two lenses together without any provision for focusing’ Galileo Galilei (1610) prepared a microscope with a focusing device called ‘occiale’. Till then, the name ‘microscope’ had not been in use and it was first proposed by Faber (or Fabri) in 1625. However, the advent of such optical lens systems did not reveal the existence of microorganisms. It was not until the mid-17th century when further development of the optical lens systems to definite microscope permitted the visualization of microorganisms that the great diversity of the microbial world began to be recognized. Robert Hooke (1635-1703) made and used a compound microscope in the 1660s and described his fascinating explorations of the newly discovered universe of microscopic creatures in his classic “Micrographia” (1665).
    [Show full text]
  • Effect of Tyndallisation Process on Microbial Quality and Shelf Life of Gulabjamun
    The Pharma Innovation Journal 2020; 9(12): 30-32 ISSN (E): 2277- 7695 ISSN (P): 2349-8242 NAAS Rating: 5.03 Effect of tyndallisation process on microbial quality TPI 2020; 9(12): 30-32 © 2020 TPI and shelf life of Gulabjamun www.thepharmajournal.com Received: 18-10-2020 Accepted: 23-11-2020 S Banupriya, G Kumaresan and C Kathirvelan S Banupriya Department of Livestock Abstract Products Technology, Dairy A study has been carried out to enhance the shelf life of Gulabjamun by tyndallization. Gulabjamun were Science, Veterinary College and prepared under aseptic conditions in the laboratory as per standard procedure. All the samples of Research Institute, Tamil Nadu gulabjamun were packed in 16 glass containers. Eight samples were tyndallized and others were kept as Veterinary and Animal Sciences control. Standard Plate Count, Coliform Count and Yeast and Mould Count analysis were carried out in University, Namakkal, Tamil tyndallized and control gulabjamun. Sensory evaluation on a nine point Hedonic Scale was done for Nadu. India treated and untreated products stored at ambient condition (30 ˚C) at 0 day, 7th, 21st, 28th and till they were acceptable based on organoleptic test and consumer acceptance. It was observed that the shelf life G Kumaresan of gulabjamun was extended by 28 days and beyond at room temperature. The different microbial count Department of Livestock Products Technology, Dairy also within the permissible limit in tyndallized product than control. It has been concluded that of Science, Veterinary College and tyndallization process in gulabjamun is suggested to enhance the shelf life of the product up to 28 days in Research Institute, Tamil Nadu room temperature.
    [Show full text]
  • International Journal of Food Microbiology Design of Microbial Consortia for the Fermentation of Pea-Protein-Enriched Emulsions
    International Journal of Food Microbiology 293 (2019) 124–136 Contents lists available at ScienceDirect International Journal of Food Microbiology journal homepage: www.elsevier.com/locate/ijfoodmicro Design of microbial consortia for the fermentation of pea-protein-enriched emulsions T Salma Ben-Harb, Anne Saint-Eve, Maud Panouillé, Isabelle Souchon, Pascal Bonnarme, ⁎ Eric Dugat-Bony, Françoise Irlinger UMR GMPA, AgroParisTech, INRA, Université Paris-Saclay, 78850 Thiverval-Grignon, France ARTICLE INFO ABSTRACT Keywords: In order to encourage Western populations to increase their consumption of vegetables, we suggest turning Legume legumes into novel, healthy foods by applying an old, previously widespread method of food preservation: Aroma profile fermentation. In the present study, a total of 55 strains from different microbial species (isolated from cheese or Bacteria plants) were investigated for their ability to: (i) grow on a emulsion containing 100% pea proteins and no Fungi carbohydrates or on a 50:50 pea:milk protein emulsion containing lactose, (ii) increase aroma quality and reduce Microbial assembly sensory off-flavors; and (iii) compete against endogenous micro organisms. The presence of carbohydrates in the mixed pea:milk emulsion markedly influenced the fermentation by strongly reducing the pH through lactic fermentation, whereas the absence of carbohydrates in the pea emulsion promoted alkaline or neutral fer- mentation. Lactic acid bacteria assigned to Lactobacillus plantarum, Lactobacillus rhamnosus, Lactococcus lactis
    [Show full text]
  • Sterilization, Disinfection and Biosafety
    Sterilization, Disinfection and Biosafety Department of Microbiology College of Medicine University of Baghdad Learning Objectives . Define Sterilization and disinfection . Identify the different types or methods of sterilization . Recognize the biosafety in operation theaters and hopspitals . Recognize the standard microbiological practices . Define procedures used by laboratories to protect workers and others from infection . List the types of infectious waste. Sterilization • Sterilization – The killing or removal of all form of microbial life including spores. – Sterilization of instruments, drugs and supplies is important for the prevention of infection. • Disinfection – Is reducing the number of bacteria to a level low enough that disease is unlikely to occur – It a is less lethal process than sterilization. Types of sterilization Types of sterilization Chemical Physical methods methods Filtration Radiation Heat Mild Potent Non- Dry heat Moist ionizing heat ionizing Read heat At a temperature (direct Autoclaving At a temperature below 100c flaming) above 100c Infra-red Hot of 100c radiation air oven Boiling at Tyndallization 100c Physical methods • Heat 1. Dry heat a) Red heat: heating of platinum loop, points of forceps, needles and mouth of culture tubes. Physical methods b) Hot air oven: Temperature of 160 °C for 1 hour is employed. Hot air oven is the best method for sterilizing dry glassware, forceps, scalpels...other steel & dental &surgical instruments, powders, fat, greases. Physical methods c) Infra-red radiation: the source employed is an electrically heat element, a temperature of 180° C can be attained. Used for glassware. Physical methods • d) Incineration: This is an excellent method of destroying materials such as contaminated cloth, animal carcasses and pathological materials.
    [Show full text]
  • Gamma Irradiation and Autoclave Sterilization Peat and Compost As the Carrier for Rhizobial Inoculant Production
    Journal of Agricultural Science; Vol. 4, No. 12; 2012 ISSN 1916-9752 E-ISSN 1916-9760 Published by Canadian Center of Science and Education Gamma Irradiation and Autoclave Sterilization Peat and Compost as the Carrier for Rhizobial Inoculant Production Panlada Tittabutr1, Kamonluck Teamthisong2, Bancha Buranabanyat1, Neung Teaumroong1 & Nantakorn Boonkerd1 1 School of Biotechnology, Suranaree University of Technology, Nakhon Ratchasima, Thailand 2 The Center for Scientific and Technological Equipment, Suranaree University of Technology, Nakhon Ratchasima, Thailand Correspondence: Nantakorn Boonkerd, School of Biotechnology, Suranaree University of Technology, Nakhon Ratchasima, Thailand. Tel: 66-4422-4501. E-mail: [email protected] Received: August 1, 2012 Accepted: August 28, 2012 Online Published: November 15, 2012 doi:10.5539/jas.v4n12p59 URL: http://dx.doi.org/10.5539/jas.v4n12p59 Abstract Rhizobium is a biofertilizer for leguminous crops. To formulate this form of fertilizer, the suitable sterilization processes of carrier are important. Therefore, the aim of this research was to elucidate the process of gamma irradiation and autoclaving on peat and compost based carriers for rhizobial inoculant production. Carriers with 10% moisture content packing in polyethylene bag could be efficiently sterilized by irradiation at 10-20 kGy, or by autoclaving with tyndallization approach (autoclaving two times in a row at 121ºC for 60 min, with waiting period of 18 hours after each time of autoclaving). The number of Bradyrhizobium sp. PRC008 was in the range of 108-109 cfu/g in both irradiated and autoclaved peat after 6 months storage. However, the numbers of bradyrhizobial cell were reduced in compost sterilized by both methods after one month storage.
    [Show full text]
  • WO 2016/097248 Al 23 June 2016 (23.06.2016) W P O P C T
    (12) INTERNATIONAL APPLICATION PUBLISHED UNDER THE PATENT COOPERATION TREATY (PCT) (19) World Intellectual Property Organization International Bureau (10) International Publication Number (43) International Publication Date WO 2016/097248 Al 23 June 2016 (23.06.2016) W P O P C T (51) International Patent Classification: (81) Designated States (unless otherwise indicated, for every A61Q 5/06 (2006.01) A61K 36/00 (2006.01) kind of national protection available): AE, AG, AL, AM, A61K 8/97 (2006.01) AO, AT, AU, AZ, BA, BB, BG, BH, BN, BR, BW, BY, BZ, CA, CH, CL, CN, CO, CR, CU, CZ, DE, DK, DM, (21) Number: International Application DO, DZ, EC, EE, EG, ES, FI, GB, GD, GE, GH, GM, GT, PCT/EP20 15/080403 HN, HR, HU, ID, IL, IN, IR, IS, JP, KE, KG, KN, KP, KR, (22) International Filing Date: KZ, LA, LC, LK, LR, LS, LU, LY, MA, MD, ME, MG, 18 December 2015 (18. 12.2015) MK, MN, MW, MX, MY, MZ, NA, NG, NI, NO, NZ, OM, PA, PE, PG, PH, PL, PT, QA, RO, RS, RU, RW, SA, SC, (25) Filing Language: English SD, SE, SG, SK, SL, SM, ST, SV, SY, TH, TJ, TM, TN, (26) Publication Language: English TR, TT, TZ, UA, UG, US, UZ, VC, VN, ZA, ZM, ZW. (30) Priority Data: (84) Designated States (unless otherwise indicated, for every 1462873 19 December 2014 (19. 12.2014) FR kind of regional protection available): ARIPO (BW, GH, GM, KE, LR, LS, MW, MZ, NA, RW, SD, SL, ST, SZ, (71) Applicant: L'OREAL [FR/FR]; 14, rue Royale, 75008 TZ, UG, ZM, ZW), Eurasian (AM, AZ, BY, KG, KZ, RU, Paris (FR).
    [Show full text]
  • Ensuring Dairy Raw Biological Safety by Tyndallization
    ©2021 International Transaction Journal of Engineering, Management, & Applied Sciences & Technologies ISSN 2228-9860 eISSN 1906-9642 CODEN: ITJEA8 International Transaction Journal of Engineering, Management, & Applied Sciences & Technologies http://TuEngr.com Ensuring Raw Dairy Biological Safety by Tyndallization Vladimir Kaishev1 1 Department of Technology of Production and Processing of Agricultural Products, Stavropol State Agrarian University, Stavropol, RUSSIA. *Corresponding Author (Tel: +7-999 55 00 00, Email: [email protected]) Paper ID: 12A5B Abstract Volume 12 Issue 5 The article provides a theoretical substantiation of the technological Received 23 December 2020 platform for ensuring the biological safety of raw milk by the method Received in revised form 12 of controlled thermal cleaning before technological processing. Investigated February 2021 alternative options for bacterial purification of raw milk by heating, with Accepted 24 February 2021 exposure to a soft regime, improved its microbiological, physicochemical, Available online 02 March and technological properties. The technology of low-temperature heat 2021 treatment of whey has been substantiated, making it possible to achieve Keywords: microbiological purification, stabilization, and preservation of the quality of Milk; Whey; Microbial contamination; Heat raw materials, with the possibility of its preservation further use in obtaining treatment; Thermized functional food products and feed means of a new generation. milk; Technological Disciplinary: Biotechnology,
    [Show full text]