ACCESS HOLE REQUIRED: DECK EDGE + + C OF + - DECK LAMINATE 305(12") 50- HEIGHT x 460 (18") 50 WIDTH- +25 -50 L ACCESS HOLE REQUIRED: OFFSET TO ALLOW FOR VARIATION OFFSET TO ALLOW FOR VARIATION FILL VOID BETWEEN COVERING BOARD AND HULL + + 305 (12") 50 -HEIGHT x 460 (18") 50 WIDTH- IN DECK THICKNESS (FROM DECK IN DECK THICKNESS (FROM DECK DECK LAMINATE WITH GEL COAT, CABOSIL (OR REC. 350 (13-3/4")H. x 505(19-7/8")W. C OF BOW STRINGERS (3), P/S L REC. 350L (13-3/4") H. x 505 (19-3/8") W. EDGE TO OUTBOARD EDGE OF EDGE TO OUTBOARD EDGE OF OFFSET TO ALLOW FOR AEROSIL, OR EQUIVALENT) AND RESIN MIXTURE + C OF HULL -2 C OF HOLE SHALL BE ON C OF HULL, 50. - BALSA CORE) IS OPTIONAL. BALSA CORE) IS OPTIONAL. VARIATION IN DECK THICKNESS 280(11") 50 L L L -1 1/2 DECK EDGE + + -1 - 460(18-1/8") 30 510(20") 30- (FROM DECK EDGE TO OUTBOARD +25 -1/2 310(12-3/16") 30 COVERING BOARD -260 O ACCESS COVER REQUIRED: 260 EDGE OF BALSA CORE) IS OPTIONAL. I.Y.R.U. PLAGUE (3/8") 1 (3/8") (3/8") 160(6-5/16") 6MM(1/4") THK. FIR PLYWOOD (MARINE) LAMINATED PORT/ST'B'D. 2 12MM (1/2") 6 MM (1/4") THK. PLYWOOD BHD. OR KNEE, EXCEPT 6MM (1/4") THK. PLYWOOD BHD. COVERED WITH 2 3 2 BOTH SIDES & ALL EDGES W/ 1 PLY 340 G/M (10 OZ.) 4 END GRAIN FOR 12MM (1/2") THK. FORWARK (CHAINPLATE) KNEE, 1 PLY 340 G/M (10 OZ.) GLASS CLOTH, BOTH SIDES 5 5 100 100 GLASS CLOTH, OR 6MM (1/4") LEXAN, OR EQUIVALENT + 100 2 TR. 11-1/2 REC.225(10") - + + BALSA CORE COVERED WITH 1 PLY 340 G/M (10 0Z.) GLASS CLOTH, 6 8 9 10 11 122(4-13/16") 10 331(13") 10- 389(15-5/16") 10 - BHD. BONDING 540(21-1/4") 30 BOTH SIDES. 655 (25-13/16") 30

1 PLY 225 G/M (3/4 OZ.) MAT LAID 100 100 100 TAPES + + REC. 10 +

REC. 10 80(3-1/8") 10 - REC. 10 238(9-3/8") 10 - - BETWEEN DECK & COVERING BOARD BONDING LAYUP SCHEDULE - BHD. TO HULL - (MANDATORY): 300(11-3/16") 10 745(29-5/16") 30 NOTES 2 REC. 255(10") 1 PLY 340 G/M (10 OZ.) GLASS CLOTH, REC. 200 (8") WIDE TAPE BHD. BONDING TAPES 100 100 + 100 + + OVER 1 PLY 450 (1-1/2 OZ.) MAT, REC. 150 (6") WIDE TAPE. 65(2-9/16") 10 - 171(6-3/4") 10 - 234(9-3/16") 10 - 1. THE HULL (INCLUDING DECK), KEEL, SKEG, RUDDER, STANDING RIGGING, SPARS AND SAILS (BONDING LAYUP SCHEDULE FOR BHD. TO DECK REFER TO REC. 230(9") ARE STRICTLY CONTROLLED IN ACCORDANCE WITH THE INTERNATIONAL E-22 CLASS RULES + REC. HULL/DECK JOINT BONDING LAYUP SCHEDULES STRAKE "A" - +

+ 100 - 100 HULL LAMINATE ATTACHMENT OF AFTER BHD. & KNEES DETAIL.) + 100 + PERTAINING TO ONE-DESIGN CONTROL, THE OFFICIAL PLANS AND SPECIFICATIONS, 2 47(1-7/8") 10 - 117(4-5/8") 10 - 181(7-1/8") 10 - 1 PLY 450 G/M (1-1/2 OZ.) MAT, 150 (6") WIDE TAPE OVER MEASUREMENT FORM, MEASUREMENT DIAGRAMS AND CONSTRUCTION MANUAL, BHD. BONDING LAYUP SCHEDULE TO HULL & DECK (MANDATORY): + 2 REC. CONST. 330(13") - 1 PLY 450 G/M (1-1/2 OZ.) MAT, 100 (4") WIDE TAPE. 1 PLY 340 G/M (10 2OZ.) GLASS CLOTH, REC. 125 (5") WIDE TAPE, REC. 230(9") MIN. 255/MAX. 405 MATERIALS, LAYUP SCHEDULES, ASSEMBLIES, FITTINGS, PARTS, STRUCTURAL 100 + + + 100 2 REC. 230(9") 64(2-1/2") 10 - - 133(5-1/4") 10 - MEMBERS (SEAT, BULKHEADS, KNEES, BOW STRINGERS, DECK STIFFENERS) AND OVER 1 PLY 450 G/M (1-1/2" OZ.) MAT, REC. 100 (4") WIDE TAPE. + A - 520(20-1/2") 30 STRUCTURAL REINFORCEMENT SHOWN ON THIS CONSTRUCTION PLAN ARE MANDATORY

+ 100 KNEE BONDING LAYUP SCHEDULE TO HULL & DECK (MANDATORY): TOP OF COAMING 85(3-3/8") 10 - UNLESS SPECIFICALLY NOTED AS "RECOMMENDED (REC.)" OR "OPTIONAL (OPT.)". 2 D.W.L. D.W.L. 1 PLY 340 G/M (10 OZ.) GLASS CLOTH, REC. 100 (4") WIDE TAPE, D.W.L. REC. 230 (9") DIMENSIONS WITH TOLERANCES INDICATED ARE MANDATORY. MEASUREMENTS OVER 1 PLY 450 G/M (1-1/22 OZ.) MAT, REC. 75 (3") WIDE TAPE. REC. 10 630(24-13/16") 30 SECTION THRU HULL/DECK JOINT MICROBALLOONS & RESIN, OR EQUIVALENT A (3/8") REQUIRED FOR THE INTERNATIONAL E-22 CLASS MEASUREMENT FORM (1974) ARE STRAKE "B" 800(31-1/2") 30 SO INDICATED BY ENCLOSING THE ITEM NUMBERS LISTED ON THE MEASUREMENT (MOULDS #1 & #3) MINIMUM ALLOWABLE REC. DRAIN PLUG (SCREW- REC. 10 FORM IN BRACKETS, I.E. [#20]. PARTS AND FITTINGS SPECIFIED AS "ONE-DESIGN 2 (3/8") REC. 12 (1/2") CONSTANT CLEARANCE BTN. BULKHEAD AND HULL/DECK REC. DRAIN PLUG (SCREW- NOTE: COVERING BOARD IS PART OF THE HULL LAMINATE. 1 PLY 225 G/M (3/4 OZ.) MAT, OFFSET: 100 (3.94") ACCESS COVER REQUIRED: IN TYPE REQUIRED). FITTING" (I.E. STEM FITTING, CHAINPLATE, MAST STEP, BACKSTAY FITTING, RUDDER

REC. 12 (1/2") CONSTANT CLEARANCE BTN. BHD. AND HULL/DECK, KNEE HULL REC. CONST. (410(16") 2 IN TYPE REQUIRED). MIN. 335/MAX. 485 AFTER KNEE 1 PLY 450 G/M (1-1/2 OZ.) MAT 6MM (1/4") THK. FIR PLYWOOD (MARINE) STOCK) ARE MANDATORY AND SHALL BE FABRICATED IN ACCORDANCE WITH (3) HULL REINFORCEMENT (120MM FORWARD STATION 6) REC. 10 LAMINATED BOTH SIDES & ALL EDGES W/ DWG. NO. 3MKB-15G "FITTINGS DETAIL". THE DESIGN OF THE RUDDER HEAD, TAPES IN WAY OF BHD. 7 (3/8") SIDE DECK 1 PLY 340 G/M (10 OZ.)2 GLASS CLOTH, OR MATERIAL: 6MM (1/4") THK. FIR PLYWOOD (MARINE) INTERMDIATE KNEE TILLER, TILLER EXTENSION AND LIFTING EYES IS OPTIONAL, EXCEPT NO EXOTIC SECTION AT AFTER BHD. STRAKE "C" 6MM (1/4") LEXAN, OR EQUIVALENT. LAMINATED BOTH SIDES & ALL (THREE) EDGES WITH (915 MM FORWARD STATION 6) MATERIALS SHALL BE USED. THE DETAIL DESIGN OF OTHER FITTINGS ON THIS LOOKING AFT 340 G/M (10 OZ.) GLASS CLOTH. CONSTRUCTION PLAN IS OPTIONAL PROVIDED THAT THEY ARE OF THE GENERAL TYPES + 12MM (1/2") END MATERIAL: 6MM (1/4") THK. FIR PLYWOOD (MARINE) - REC. CONST. 350(14") SHOWN ON THIS PLAN. IT IS IMPOSSIBLE TO MENTION EVERY SUGGESTION THAT HAS 25(1") 6 GRAIN BALSA CORE MIN. 275/MAX. 425 + (2.95") LAMINATED BOTH SIDES & ALL (THREE) EDGES WITH

75 MAX. STRAKE "D" FILL WITH CHOPPED STRANDS & RESIN MIXTURE, WHERE - STATION 2 BEEN RULED ILLEGAL IN THE PAST, AND TO FORESEE EVERY INNOVATION WHICH MAY BE 25(1") 6 340 G/M (102 OZ.) GLASS CLOTH. THE TIGHT CURVATURE OF THE DECK EDGE MAKES IT LOOKING END BHD. GASKET REQ'D. _ 3 x 12(1/8" x 1/2") FWD. (CHAINPLATE) KNEE THOUGHT OF IN THE FUTURE. THEREFORE WHEN CONSIDERING ANYTHING IN CONNECTION PRESSURE SENSITIVE RUDDER STRIP, DIFFICULT TO LAYUP THE BONDING PLIES CONTINUOUSLY (1690 MM FORWARD STATION 6) WITH THE YACHT OR ITS SAILS OR EQUIPMENT WHICH IS NOT CLEARLY COVERED BY THE ALONG THE HULL AND DECK LAMINATES. VOIDS BETWEEN ACCESS COVER OR EQUIVALENT. NOTE: REC. KEEL ROOT OF HULL AND TOP OF PLANS, SPECIFICATION AND/OR RULES, IT MUST BE ASSUMED ILLEGAL UNLESS PRIOR THE BONDING PLIES AND THE HULL AND DECK LAMINATES MATERIAL: 12 MM (1/2") THK. FIR PLYWOOD (MARINE) APPROVAL HAS BEEN OBTAINED FROM I.Y.R.U. THROUGH THE E-22 INTERNATIONAL HULL 2 LEAD KEEL BE RABBETED TO PERMIT AT THE DECK EDGE WILL CAUSE FRACTURING OF THE LAMINATED BOTH SIDES & ALL (THREE) EDGES WITH 2 ASSOCIATION. 450 G/M (1-1/2+ OZ.)MAT. + GLASS TAPES AT HULL/KEEL JOINT TO HULL/KEEL JOINT LAYUP SCHEDULE: 2 - - 5 MAX. 340 G/M (10 OZ.) GLASS CLOTH. HULL/DECK JOINT SEAM. THE AMOUNT OF CHOPPED STRANDS 2 1 PLY 225 G/M (3/4 OZ.) MAT. 50(2") 5 WIDE TAPE LIE FLUSH (REFER TO RULE 2.3). REC. (2) PLIES 340 G/M 2 2. HULL, DECK, SEAT, SKEG AND RUDDER SHALL BE OF GLASS REINFORCED POLYESTER (3/4") & RESIN MIXTURE TO BE MINIMIZED; TOO MUCH MIXTURE REC.19 1 PLY 450 G/M (1-1/2 OZ.) MAT. (2.95") 75 MAX. (0.20") 2 2 + (10 OZ.) GLASS TAPE RESIN (G.R.P.) IN ACCORDANCE WITH THE RULES, OFFICIAL PLANS AND SPECIFICATIONS WILL ALSO CAUSE FRACTURING OF THE HULL/DECK JOINT DECK LAMINATE - 2 1 PLY 610 G/M (18 OZ.) WOVEN ROVING

ATTACHMENT OF 1 PLY 450 G/M (1-1/2 OZ.) MAT. L C AND SHALL BE MADE ONLY FROM OFFICIAL MOULDS CONSTRUCTED SOLELY BY BUILDERS SEAM. WHERE THE CURVATURE OF THE DECK EDGE 450 G/M (1-1/2 OZ.)MAT. 100(4") 5 WIDE TAPE 2 EPOXY RESIN & COBOSIL MIXTURE (OR EPOXY & 1 PLY 610 G/M (18 OZ.) W.R. LEAD KEEL 2 2 LICENSED FOR THAT PURPOSE BY THE I.Y.R.U. THE LAYUP SCHEDULE FOR THE IS LARGE ENOUGH, THE CHOPPED STRANDS & 2 ASBESTINE, OR EQUIVALENT) TO BE APPLIED 1 PLY 225 G/M (3/4 OZ.) MAT 2 PLIES 450 G/M (1-1/2 OZ.) MAT - 280x450 (11"x18") AFTER BHD. & KNEES 2 HULL, DECK. SKEG, RUDDER, TANK TOP, AND SEAT IS AS FOLLOWS: RESIN MIXTURE IS NOT NECESSARY. 450 G/M (1-1/2 OZ.)MAT. 150 (6") 5 WIDE TAPE BETWEEN BOTTOM OF HULL KEEL ROOT & TOP 6MM (1/4") DIA. BOLT W/NUT. 1 PLY 450 G/M (1-1/2 OZ.) MAT. HULL 2 HULL LAYUP SCHEDULE: FULL SIZE 1 PLY 450 G/M (1-1/2 OZ.) MAT. OF LEAD KEEL. 12 REQ'D _ REC. BOLT BE AFFIXED 2 2 REC.75 (3") TO BALSA CORE FILL ALL HOLES IN CHAINPLATE STRAKE "A" - 2 PLIES 450 G/M (1-1/2 OZ.) MAT; 1 PLY 610 G/M (18 OZ.) WOVEN ROVING REC. 125 (5") WIDE TAPE TO BHD. IN SUCH A WAY TO PREVENT 12MM (1/2") END HULL 2 2

REC. TRIM COAMING TO TRACE OF OUTBOARD WITH CHOPPED STRANDS AND

NOT LESS THAN 75 (3") STATION 5 STRAKE "B" - 2 PLIES 450 G/M (1-1/2 OZ.) MAT; 2 PLIES 610 G/M (18 OZ.) WOVEN ROVING IT TURNING WHEN TIGHTINING OR GRAIN BALSA CORE 2 2 EDGE OF BALSA CORE LOOKING FWD. AND AFT. RESIN. STRAKE "C" - 3 PLIES 450 G/M (1-1/2 OZ.) MAT; 3 PLIES 610 G/M (18 OZ.) WOVEN ROVING FORWARD BHD. ATTACHMENT LOOSENING NUT. ADHESION OF 2 MICROBALLOONS & RESIN, OR EQUIVALENT BULKHEAD STRAKE "D" - 4 PLIES 450 G/M (1-1/2 OZ.)MAT; 4 PLIES 610 G/M (18 OZ.) WOVEN ROVING2 RESIN OR GLASS TAPE TO BOLT TRANSOM - 2 PLIES 450 G/M (1-1/2 OZ.)MAT;2 1 PLY 610 G/M (18 OZ.) WOVEN2 ROVING 12MM (1/2") END 6MM (1/4") THK. FIR PLYWOOD (MARINE) REINFORCEMENT AND HULL REINFORCEMENT HEAD IS NOT RELIABLE. GRAIN BALSA CORE CHAINPLATE STRAKES "A", "B", "C", AND "D" LAMINATES SHALL OVERLAP 75 (3") ON EITHER

FULL SIZE 264(10-3/8") L FILL W/MICROBALLOONS LAYUP SIDE OF THE CENTERLINE OF THE HULL. SECTION E-E +2 SECTION A-A C 2 -4 1 PLY 450 G/M (1-1/2" OZ.) MAT. (#22 & #23) AND RESIN MIXTURE DECK LAYUP SCHEDULE (INCLUDING CUDDY TOP): HULL/DECK JOINT SEAM: FULL SIZE FULL SIZE 1 PLY 610 G/M (18 2OZ.) WOVEN ROVING KNEE LAYUP SCHEDULE (MANDATORY): 2 OR EQUIVALENT 2 PRIMARY BOND OR BARRIER LAMINATE. 1 PLY 225 G/M (3/4 OZ.) MAT. - CURE - CAMFER HULL AND DECK LAMINATES AS REC. SEAT BONDING LAYUP SCHEDULE (TO HULL & DECK): + 1 PLY 450 G/M (1-1/2 OZ.) MAT - REC. 75 (3") WIDE TAPE 2 2 NOTE: LOCAL REINFORCEMENT IN WAY OF THE ATTACHMENT OF FITTINGS TO THE 175(6-7/8") 100 - 1 PLY 450 G/M (1-1/2 OZ.) MAT. SHOWN, THEN APPLY A MIXTURE OF GEL REC. HULL/DECK JOINT BONDING LAYUP SCHEDULE: 2 2 1 PLY 340 G/M (10 OZ.) GLASS CLOTH OVER 12MM(1/2") THK. KNEE 1 PLY 340 G/M (10 OZ.) GLASS CLOTH - REC. 100 (4") WIDE TAPE 1 PLY 450 G/M (1-1/2 OZ.) MAT, 150 (6") WIDE TAPE 2 COAMING IS PERMITTED. IT SHALL CONSIST OF THE ADDITION OF GLASS SECTION B-B 12 MM (1/2") END GRAIN BALSA CORE (OUTBOARD EDGE 75 (3") IN FROM DECK EDGE), COAT (SAME COLOR AS HULL), CABOSIL (OR 2 1 PLY 450 G/M (1-1/2 OZ.) MAT. 100 (4") WIDE TAPES. LOCAL REINFORCEMENT 1 PLY 450 G/M (1-1/2 OZ.) MAT, 175 (7") WIDE TAPE FIBER TAPES AND/OR BACK-UP PLATES OF METAL, WOOD, FILLER, RESIN, VACUUM BAG CURE, OR EQUIVALVENT. AEROSIL, OR EQUIVALENT) AND RESIN. 2 IN ACCORDANCE W/ RULES 3.1, FULL SIZE 2 1 PLY 450 G/M (1-1/2 OZ.) MAT, 200 (8") WIDE TAPE. GLASS FIBER OR ANY COMBINATION THERE OF AND SHALL NOT EXCEED IN 1 PLY 450 G/M (1-1/2 OZ.)MAT. SECTION II IN WAY OF WINCH (5) 2 AREA THE AMOUNT REQUIRED FOR PREVENTION OF LOCAL CRUSHING OR CHAINPLATE. 1 PLY 610 G/M (18 OZ.) WOVEN ROVING THE FRACTURE OF THE COAMING. (REFER TO RULE 3.1) ADDITIONAL PLY 450 G/M (1-1/22 OZ.) MAT IN WAY OF COAMING. (ONE-DESIGN FITTING) TRACE OF OUTBOARD REFER TO DWG. 3MKB-15G COVERING BOARD LAYUP SCHEDULE (MAY EQUAL OR EXCEED FOLLOWING SCHEDULE): EDGE OF BALSO CORE. 2 TRANSOM: PRIMARY BOND OR BARRIER LAMINATE - 1 PLY 225 G/M (3/4OZ.)MAT. CURE - FILL WITH CHOPPED STRANDS & RESIN MIXTURE (SERVES DECK 2 (STRAKE "A" E 2 PLIES 450 G/M (1-1/2 OZ.) MAT. AS THE COMPRESSION COMPONENT OF THE JOINT). FAIR REC. 30(1-3/16") LAYUP SCHEDULE) 3823(12'- 6-1/2") (#20 & #21) 2 MIXTURE INTO HULL & DECK (TO EDGE OF BALSA CARE) REC. 150 (6") DIA. SOLID G.R.P. REC. 30(1-3/16") 1 PLY 610 G/M (18 OZ.) WOVEN ROVING MAX. 40(1.57") SKEG AND RUDDER LAYUP SCHEDULE: LAMINATES AS SHOWN TO MINIMIZE STRESS CONCENTRATION. +12 (NO BALSA CORE) REINFORCEMENT TRANSOM REINFORCEMENT (MANDATORY): -13 FOR HEADSTAY HARDWARE. (#24 AND #25) PRIMARY BOND OR BARRIER LAMINATE - 1 PLY 225 G/M (3/4 OZ.)MAT.2 CURE - 1 PLY 450 G/M (1-1/22 OZ.) MAT. LENGTH: OUTBOARD EDGE MAX. 40(1.57")(#24/#25) (1 PLY 450 G/M (1-1/22 OZ.) MAT MAY BE SUBSTITUTED FOR THE 225 G/M (3/4 OZ.) MAT 2 FROM TOP TO BOTTOM OF TRANSOM; E OF TANK TOP 2 PLIES 450 G/M (1-1/2 OZ.)2 MAT (1 PLY OF 610 G/M (18 OZ.) WOVEN ROVING2 MAY BE 2 SECTION THRU HULL/DECK JOINT WIDTH: REC. 150 (6") WIDE TAPE. REC. TO + SUBSTITUTED FOR 1 PLY 450 G/M (1-1/2 OZ.) MAT) HULL LAMINATE - C DECK (WOOD) STIFFENER, P/S - LENGTH 1525(60") 100 (ALTERNATIVE METHOD) BE APPLIED AFTER BARRIER LAMINATE. REC. FILL VOID WITH TANK TOP LAYUP SCHEDULE: 2 + - REFER TO DETAIL OF DECK STIFFENERS FOR MICROBALLONS AND 1 PLY 450 G/M (1-1/2 OZ.) MAT LIFTING EYE (2) + 12MM (1/2") END GRAIN - RESIN, OR CHOPPED 1 PLY 610 G/M (18 OZ.)2 WOVEN ROVING REQ'D. DESIGN + DIMENSIONS AND LAYUP SCHEDULE

NOTES: 1. COVERING BOARD IS PART OF THE DECK LAMINATE + - REC.470(18-1/2") 530(20.87")MAX. BALSA CORE. TRACE OF 12MM (1/2") C DECK (WOOD) STIFFENER, P/S-LENGTH 1015(40") 100 202(7.95") 2 (#26)- STRANDS AND RESIN, 2. THIS METHOD REQUIRES LESS PRECISION IN BACKSTAY FITTING BONDING LAYUP SCHEDULE (MANDATORY MIN.): OPTIONAL. SEAT LAYUP SCHEDULE: END GRAIN BALSA CORE 1 PLY 450 G/M (1-1/22 OZ.) MAT. 150 WIDE x 200 LG. (6"x8") P/S REFER TO DETAIL OF DECK STIFFERNERS REC.400(15-3/4") OR EQUIVALENT. 3 PLIES 450 G/M (1-1/2 OZ.)2 MAT APPLICATION, BUT IS HEAVIER THAN THE RECOMMENDED 2 B + - 1 PLY 610 G/M (18 OZ.) WOVEN ROVING. 150 W. x 200 LG. (6"x8") P/S FOR DIMENSIONS AND LAYUP SCHEDULE. 5 + - THE BUILDER SHALL FOLLOW PROCEDURES AND STANDARDS WHICH ENSURE STRICT CONTROL

METHOD. SECTION F-F DRILL 10MM (3/8") DIA. DRILL (6") 12MM(1/2") THK. KNEE 1 PLY 450 G/M (1-1/22 OZ.) MAT. 200 WIDE x 250 LG. (8"x10") P/S 4 3

305(12") 50 OF THE ONE-DESIGN SHAPE AND SHALL ASSEMBLE THE COMPONENTS IN ACCORDANCE 175 50 1 0 -1/2 150 50 -1 -1 1/2 6 2 300(11-13/16") 50 REC CHAINPLATE LAYUP SCHEDULE HOLES IN FOOT WELLS, P/S 2 (6-7/8") 11 10 9 8 7 -2 FILL ALL HOLES IN REC. BONDING LAYUP SCHEDULE FOR ATTACHMENT OF PLYWOOD TO SEAT: TRACE OF 6MM (1/4") THK. FIR 1 PLY 610 G/M (18 OZ.)WOVEN ROVING 200 W. x 250 LG. (8"x10") P/S 2 PLIES 450 G/M (1-1/2 2OZ.) MAT, 280x450 (11" x 18"), ARE WITH RULE 3.2 "HULL AND DECK ASSEMBLY", RULE 3.9.1 " THE GLASS HULL", AND RULE 3.9.2 2 PLYWOOD (MARINE)_ FORMS (SAME SCHEDULE FOR BONDING BOTTOM OF BACKSTAY B CHAINPLATE WITH "THE BARE YACHT". LOCAL REINFORCEMENT, AS SHOWN ON THIS CONSTRUCTION PLAN 1 PLY 340 G/M (10 OZ.) GLASS CLOTH OVER APPLIED, THEN CHAINPLT. IS PRESSED INTO MAT UNTIL CURED. CHOPPED STRANDS 1 PLY 450 G/M (1-1/22 OZ.)MAT. 75 (3") WIDE TAPES BOTTOM OF SIDE LOCKERS_ FITTING TO HULL) FILL CHAINPLATE HOLES W/CHOPPED STRANDS & RESIN, THEN AND/OR DESCRIBED IN RULE 3.1 IS PERMITTED AT POINTS OR STRESS CONCENTRATION OR + - AND RESIN. APPLY 1 PLY 450 G/M (1-1/2 OZ.)MAT-330x4752 (13"x19"), CHAINPLATE HIGH LOADINGS. SUCH REINFORCEMENT SHALL NOT AFFECT THE STRENGTH OR RIGIDITY F 1 PLY 610 G/M (18 OZ.)2 WOVEN ROVING - 380x500(15"x20") (ONE-DESIGN FITTING) OF THE HULL AND/OR DECK. NOTE: BACKSTAY PENNANT MAY BE (#27) 2 2 TOP OF CONSOLE BH, BONDING 1 PLY 450 G/M (1-1/2 OZ.) MAT-430x525 (17"x21") REFER TO DWG. 3MKB-15G 3. THE KEEL SHALL BE OF LEAD CAST IN AN OFFICIAL MOULD OBTAINED FROM A REC. 1 PLY 450 G/M (1-1/2 OZ.) MAT. 305 WIDE DEAD ENDED TO AFTER BHD., OR HULL TAPES SOURCE APPROVED BY THE I.Y.R.U., AND SHALL BE IN ACCORDANCE WITH THE RULES, 200 LONG (12"x8") BE APPLIED, THEN BACKSTAY IN AFTER FLOTATION COMPARTMENT, OR 100(3.94") 2 OFFICIAL PLANS AND SPECIFICATIONS, AND MEASUREMENT FORM. A SMALL DECK LAMINATE FITTING IS PRESSED INTO MAT. UNTIL CURED. KEELSON. BHD. OR HULL IN WAY OF HULL REINFORE- 12MM(1/2") THK. KNEE KEELSON: SECURE AFTER 610 AMOUNT (APPROXIMATELY 3% OR LESS) OF ANTIMONY MAY BE ADDED TO PENNANT ATTACHMENT SHALL BE RE- MENT TAPES (24") OF KEELSON TO TANK TOP W/ IMPROVE THE WORKING SURFACE. INFORCED IN ACCORDANCE W/RULE 3.1, As of 1 Jan 2008 a additional bulkhead has been mandated HULL TRACE OF SEAT SECTION II. FRP & RESIN, IF SAMSON POST IS USED. BONDING PLIES LOCAL REINFORCEMENT IN in all new yachts. See drawings Bow_Bulkhead_2007, 4. THE ATTACHMENT OF THE DECK TO THE HULL SHALL FOLLOW THE EXAMPLES SHOWN REC.75 (3") TO BALSA CORE TO HULL & DECK BACKSTAY FITTING: (ONE-DESIGN + ACCORDANCE W/ RULE 3.1, Bow_Bulkhead_Installation_2007 and (BILGE SUMP 150 25 100 25(BILGE- SUMP) ON THIS CONSTRUCTION PLAN. OTHER METHODS FOR JOINING THE DECK TO THE FITTING). REFER TO DWG. 3MKB-15G. BHD. BONDING TAPES SECTION II, IF KICKING STRAP Bow_Bulkhead Specifications for construction and installation details. CHAINPLATE INSTALLATION HULL REQUIRE PRIOR WRITTEN APPROVAL FROM THE I.Y.R.U. THROUGH THE OUTLINE OF COCKPIT OR VANG IS ATTACHED TO CUDDY. INTERNATIONAL E-22 CLASS ASSOCIATION. NOTES: 1. 12MM(1/2") THK. KNEE IS INSTALLED AFTER THE CHAINPLATE SOLE (FLOORBOARDS) REC. 1 PLY 450 G/M (1-1/2 OZ.) MAT, 305 WIDE x (3) BOW STRINGERS (PORT/STARBOARD) HAS BEEN GLASSED IN PLACE. 5. FLOORBOARDS: REFER TO RULE 3.3.3. THE TOP SURFACE OF THE FLOORBOARDS 12MM (1/2") END 200 LONG (12"x18"), BE APPLIED THEN BACKSTAY REFER TO DETAIL OF BOW STRINGERS FOR 2. FLEXIBLE SEALANT TO BE APPLIED AROUND THE CHAINPLATE AT SHALL BE A SINGLE HORIZONTAL PLANE. THE FLOORBOARDS, INCLUDING TRANSVERSE, GRAIN BALSA CORE F FITTING IS PRESSED INTO MAT UNTIL CURED. DIMENSIONS AND LAYUP SCHEDULE. TOP OF DECK TO PREVENT WATER FROM ENTERING. REC. HEAVY LONGITUDINAL & VERTICAL MEMBERS OR REINFORCEMENT, SHALL WEIGH NOT LESS THAN 6MM (1/4") THK. FIR PLYWOOD (MARINE), DUTY MARINE SILICONE SEALANT. 15 KG-(33 LBS.) AND NOT MORE THAN 20 KG.(44 LBS.) WHEN DRY. THE DESIGN IS OPTIONAL, HULL/DECK JOINT SEAM: LAMINATED BOTH SIDES & ALL EDGES 6MM (1/4") THK. FIR PLYWOOD (MARINE) BULKHEAD EXCEPT AS SHOWN ON THIS CONSTRUCTION PLAN AND NOTED IN RULE 3.3.3. THE 2 (BHD.) LAMINATED BOTH SIDES & ALL EDGES WITH CAMFER HULL AND DECK LAMINATES AS REC. HULL/DECK JOINT BONDING SCHEDULE: W/ 340 G/M (10 OZ.) GLASS CLOTH. MATERIAL IS OPTIONAL, EXCEPT NO EXOTIC MATERIAL (I.E. CARBON FIBRES, KEVLAR, ETC.) 1 PLY 340 G/M (10 OZ.) GLASS CLOTH SHOWN, THEN APPLY A MISTURE OF GEL 1 PLY 225 G/M (3/42 OZ.) MAT, 75 (3") WIDE TAPE (FORMS BOTTOM OF SIDE LOCKERS, P/S) SHALL BE USED. +5 COAT (SAME COLOR AS HULL), CABOSIL (OR 1 PLY 610 G/M (18 2OZ.) FABMAT, 100 (4") WIDE TAPE 3820(12'- 6-3/8") (#17) -20 HULL 6MM (1/4") THK. FIR PLYWOOD (MARINE) BULKHEAD 6. THE USE OF A CONSOLE OR SAMSON POST IS OPTIONAL. THE DESIGN IS AEROSIL, OR EQUIVALENT) AND RESIN 1 PLY 610 G/M (18 2OZ.) FABMAT, 125 (5") WIDE TAPE SEAT CONSTRUCTION & INSTALLATION REC. FORM FAIRING STRIP WITH MICRO. 2 (BHD.) LAMINATED BOTH SIDED & ALL EDGES BALLOONS AND RESIN, OR EQUIVALENT OPTIONAL, EXCEPT AS SHOWN ON THIS CONSTRUCTION PLAN AND NOTED IN RULE 7.4. 2 + 7 1 PLY 610 G/M (18 OZ.) FABMAT, 150 (6") WIDE TAPE +20 -23 2 WITH 1 PLY 340 G/M (10 OZ.) GLASS CLOTH. 2660 (8- 8-3/4") (#30) -10 4560(14'- 11-1/2") (#18) 1 PLY 610 G/M (18 OZ.) FABMAT, 200 (8") WIDE TAPE THE MATERIAL IS OPTIONAL, EXCEPT NO EXOTIC MATERIAL (I.E. CARBON FIBRES, KEVLAR, ETC.) SHALL BE USED. CAREFUL APPLICATION OF THE BONDING PLIES IS NECESSARY SECTION AT BACKSTAY FITTING 9297(30'-6") (#19)+23 TO PREVENT ANY VOIDS BETWEEN THE BONDING PLIES AND SCALE: 1:2 (HALF SIZE) -12 THE HULL AND DECK LAMINATES AT THE DECK EDGE. VOIDS +27 7. THE GLASS IN ATTACHMENT OF METALIC HARDWARE IS TO BE DONE WITH WILL CAUSE FRACTURING OF THE HULL/DECK JOINT SEAM. REF. 211 1313(51-11/16") (#74)-23 + EXTREME CARE IN ORDER TO DEVELOP CONTINUITY OF STRENGTH. + + + 150(6") 150- 2115 (83.27") 10 (#28)- 2340(7'- 8-1/8") 100 - 2680(8'- 9-1/2") 100 - (8-5/16") DECK STIFFENER LAYUP SCHEDULE: 8. I.Y.R.U. PLAQUE NUMBER SHALL BE CUT INTO KEELSON OR MOULDED INTO THE 1 PLY 205 G/M (6 OZ.)2 GLASS CLOTH OVER +20 + BALSA GLASS OF THE HULL IN THE BILGE AREA. 940 (37.01") (#29)-19 670(26-3/8") 100 - + - 2 CORE 1 PLY 450 G/M (1-1/2 OZ.) MAT. REC. 180 (7") WIDE TAPES. MEASUREMENT DECK 32 3 9. BETWEEN THE FWD & AFTER B'H'D.S, THE INSIDE SURFACE OF THE HULL & UNDERSIDE OF HULL LAMINATE 220(8.66") MAX CONSOLE WIDTH 9MM (3/8") THK. PLYWOOD BHD. BONDING TAPES POINT "B" (1-1/4") DECK SHALL BE COATED W./GEL COAT. PAINT, INCL. ALIPHATIC POLYURETHANE COATINGS, ARE PARTIAL BULKHEAD PROHIBITED. SECTION THRU HULL/DECK JOINT REC. 165(6-1/2") MEASUREMENT (RECOMMENDED METHOD) POINT "A" WOOD (TYPE OF WOOD OPTIONAL) STIFFENER. (3) BOW STRINGERS (PORT/STARBOARD) + + 19 -3 FORWARD STIFF'N'RS: LENGTH 1525(60") 100 - 10. As of 1 Jan 2008 a additional bulkhead has been mandated REFER TO DETAIL OF BOW STRINGERS FOR + NOTE: 1. COVERING BOARD IS PART OF THE DECK LAMINATE. AFTER STIFFN'R'S: LENGTH 1015(40") 100 - in all new yachts. See drawings Bow_Bulkhead_2007, DIMENSIONS AND LAYUP SCHEDULE (3/4") 2. THIS METHOD PRODUCES A STRONGER AND LIGHTER + + + 120 25- 795(31-1/4") 25 - 780(30-11/16") 25 - Bow_Bulkhead_Installation_2007 and JOINT WITH LESS STRESS CONCENTRATION THAN THE HULL REINFORCE- CONSOLE (OPTIONAL) + - + Bow_Bulkhead Specifications for construction and installation details. + - - +100 -30 MENT TAPES 420(16-1/2") 75 ALTERNATIVE METHOD. REFER TO RULE 7.14 FOR REC. DRAIN PLUG (SCREW- (4-3/4") 3. ANY ALTERATIONS FROM THE RECOMMENDED METHOD LIMITATIONS. IN TYPE REQUIRED)- REC. RUDDER TUBE BONDING LAYUP SCHEDULE: MEASUREMENT C DECK STIFFENERS 38(1-1/2") 6 OR THE ABOVE ALTERNATIVE METHOD OF JOINING HULL & 2 50(1.97") MIN. POINT "C" 1 PLY 450 G/M (1-1/2 OZ.) MAT - 175 x 225 (7" x 8-3/4") G FULL SIZE DECK REQUIRES PRIOR APPROVAL OF THE E-22 INTERNATIONAL 2 FLOORBOARDS LENGTH: BHD. BOND- (TOP OF COAMING) 1 PLY 450 G/M (1-1/2 OZ.) MAT - 200 x 225 (8" x 8-3/4") + ASSOCIATION (IE22C) AND THE IYRU. 2 REC. FILL CAVITY BELOW DRAIN - ING TAPES 290(11-1/2") 25 1830(6'-0") 50 + 1 PLY 450 G/M (1-1/2 OZ.) MAT - 230 x 225 (9" x 8-3/4") - + MIN. FLOORBOARDS WIDTH: 810(31.89") 2 HOLE W/MICROBALLOONS AND - 1 PLY 450 G/M (1-1/2 OZ.) MAT - 225 x 225 (10" x 8-3/4") CHOPPED STRANDS (TO TANK TOP) 670(26 3/8") RESIN MIXTURE, OR EQUIVALENT 897(35-5/16") 15 + & RESIN-25(1") MAX. FLOORBOARDS WIDTH: TO SURFACE OF HULL - RUDDER STOCK 1000(39-3/8") 100 +50 770(30-5/16") 15 (#31) D.W.L. G.R.P. RUDDER TUBE: REC. LAYING UP (3) HIGH.-10

860 (33-7/8") REF. MIN. DISTANCE B'T'N. 32(1-1/4") 6 REC. CONSOLE BONDING LAYUP SCHEDULE: FLOOR- KEELSON PLIES 450 G/M (1-1/22 OZ.) MAT 10 FORM TUBE D.W.L. 2 ANY TWO TRANSVERSE BOARDS 2 1 PLY 450 G/M (1-1/2 OZ.) MAT, 125 (5") WIDE TAPE 1896(6'- 2 5/8") (#32) + C - NOTE: ALL DIMENSIONS ARE GIVEN IN MILLIMETRES, NUMBERS ENCLOSED 2 CENTER OF BOW STRINGER: 1 PLY 340 G/M (10 OZ.) GLASS +9 MEMBERS:250(9.84") TANK TOP 1 PLY 610 G/M (18 OZ.) WOVEN ROVING, 125(5") WIDE TAPE SECTION H-H -11 IN PARENTHESES ARE CONVERSIONS TO THE ENGLISH SYSTEM GIVEN IN FEET 2 TO POINT "C" TRANSVERSE MEMBERS: STEM FITTING CLOTH PREFORMED FROM A SHAPED MOULD. +5 + 1 PLY 450 G/M (1-1/2 OZ.) MAT, 150 (6") WIDE TAPE FULL SIZE D + AND INCHES OR INCHES. EXAMPLE: 3820(12'- 6-3/8") OR 150(6") -20 -150 2 35(1.38")MAX. THK LENGTH OF TOP STRINGER: 2465(8'-1") 150 - 1 PLY 610 G/M (18 OZ.) WOVEN ROVING, 150 (6") WIDE TAPE + NUMBERS ENCLOSED IN BRACKETS REFER TO ITEM NUMBERS ON THE LENGTH OF MIDDLE STRINGER: 2100(6'- 10-1/2") 150 - 75(3") 75 + INTERNATIONAL E-22 CLASS MEASUREMENT FORM (1974). EXAMPLE: [#17] OVERLAP OF TANK+ TOP 2142(7'- 0-5/16") (#33) G LENGTH OF BOTTOM STRINGER: 1590(5'- 2-1/2") 150 - - STEM FITTING LAYUP SCHEDULE - BOTH SIDES OF C (MANDATORYL MIN.): LAMINATES ON HULL 1 PLY 450 G/M (1-1/2OZ.)MAT.2 REC.-100W.x305 LONG (4"x12") H D 1 PLY 610 G/M (18 2OZ.)WOVEN ROVING REC.-125W.x355LG. (5"x14") STEM FITTING (ONE- +8 + 305(12")MAX -12 KEELSON (WOOD) - MANDATORY: 1 PLY 450 G/M (1-1/22 OZ.)MAT. REC.-150W.x405LG. (6"x16") DESIGN FITTING). - + + + 2 RUDDER STOCK: (ONE- 22 3- x 150 6 x 1830- 25 - 1 PLY 610 G/M (18 OZ.) WOVEN ROVING REC.-175W.x455LG. (7"x18") REFER TO DWG. BONDING PLIES LIMIT OF (7/8" x 6" x 6'-0") 3MKB-15G DESIGNER: 2 DESIGN FITTING). REFER FABMAT OF EQUIVALENT OR GREATER STRENGTH MAY BE USED REC. 1 PLY 450 G/M (1-1/2 OZ.) MAT BE APPLIED TO TANK CONSOLE BONDING H 57(2-1/4") 6 TO DWG. 3MKB-15G. SOLID MICROBALLOONS AND RESIN C TOP IN WAY OF BEARING SURFACES OF THE CONSOLE, LAMINATES. MIXTURE_REC. 4:1 RATIO (WEIGHT) REC. FILL CAVITY BELOW DRAIN HOLE L E.W. ETCHELLS

+ - W/ MICROBALLOONS AND RESIN BONDING LAYUP SCHEDULE (MANDATORY): THEN CONSOLE IS PRESSED INTO MAT UNTIL CURED. MAHOGANY CAP (OPTIONAL) 2 ROUTE 5, BOX 486 NOTE - SUMP FLOORS: 6MM (1/4") THK. FIR MIXTURE, OR EQUIVALENT. 1 PLY 610 G/M (18 OZ.) WOVEN ROVING, REC. 250(10") WIDE TAPE, MAST STEP_ (ONE- 2 EASTON, MD 21601 U.S.A. + PLYW'D (MARINE), OR 9MM (3/8") THK. FOAM, OVER 1 PLY 450 G/M (1-1/2 OZ.) MAT, REC. 200(8") WIDE TAPE TANK TOP - DESIGN FITTING)_ REFER FRP WRAPPED AROUND OR EQUIVALENT TAPED TO HULL W/2 PLIES REC. DRAIN PLUG (SCREW-IN 2 TO DWG. 3MKB-15G RUDDER STOCK RUDDER STOCK. OF 450 G/M (1-1/2 OZ.) MAT_ TYPE REQUIRED) CONTROLLING AUTHORITIES: 2 RUDDER SKEG D.W.L. 248 (9-3/4") 25 MAST STEP LAYUP SCHEDULE: REC. 1 PLY 450 G/M (1-1/2 OZ.) MAT, 150 (6") WIDE H H DRAIN HOLE B'TN. 2 PLIES 450 G/M (1-1/2OZ.)2 MAT, TAPE, BE APPLIED TO TANK TOP, THEN HULL INTERNATIONAL E-22 CLASS ASSOCATION REC. 12 (1/2") CONSTANT CLEARANCE SUMPS REQ'D._ REC. MICROBALLOONS & RESIN REC. 150 (6") WIDE TAPES, P/S MAST STEP IS PRESSED INTO MAT MICROBALLONS & RESIN BETWEEN PARTIAL BHD. AND HULL 32(1-1/4") I.D. TUBE. C BOX 534, WALL STREET STATION REC. PARTIAL BHD. BONDING LAYUP SCHEDULE (BOTH SIDES): UNTIL CURED. L CHAINGIRTHS: 2165 25 (#36) & (#37) 1 PLY 340 G/M (10 OZ.)2 GLASS CLOTH OVER 10MM? REC. DRAIN PLUG (SCREW- HULL NEW YORK, NY 10268 U.S.A. 1 PLY 450 G/M (1-1/22 OZ.) MAT. 100 (4") WIDE TAPES 9MM (3/8") THK. PLYWOOD PARTIAL BHD. COVERED WITH IN TYPE REQ'D.), PORT TANK TOP 1 PLY 340 G/M (10 OZ.) GLASS CLOTH, BOTH SIDES DRILL & TAP SKEG FOR (3) - 6MM OR ST'B'D._ INTERNATIONAL YACHT RACING UNION REC. BONDING BOTTOM OF RUDDER TUBE TO HULL WITH (1/4") DIA. MACHINE SCREWS 3620(11'- 10-1/2") (#35) SUMP FLOOR (4) - REFER TO NOTE HULL 2 SECTION C-C 60 KNIGHTSBRIDGE CL CL (2) PLIES 450 G/M (1-1/2 OZ.) MAT. 75(3") WIDE TAPES RUDDER STOCK MACHINE SCREWS ARE COATED 4675 (15'- 4-1/16") 15(#34) W./RESIN AND SCREWED INTO SCALE 1:2 (HALF SIZE) BOW STRINGERS LONDON SW1 7JX ENGLAND +0 SKEG. COVERING W./FRP IS OPT. REC. 110 (4-3/8") HOLE IN PARTIAL BHD. +15 45 -7 -20 FULL SIZE + - SECTION D-D MICROBALLOONS & RESIN MIXTURE (#46) 80 (FOR PASSAGE OF BACKSTAY PENNANT & WATER) NOTES: 1. REC. BOW STRINGERS TO BE FORMED FROM FIBERGLASS SCALE: 1:2 (HALF SIZE) MOULDS SHAPED ALONG THEIR LENGTH TO FOLLOW THE CURVATURE INTERNATIONAL E-22 CLASS OF THE HULL TO PREVENT BUILT IN STRESSES. SECTION G-G (AT PARTIAL BLD.) 11 10 9 8 7 6 5 4 3 2 1 0 -1/2 -1 -1 1/2 -2 STATIONS 2. BONDING PLIES SHALL BE TAPERED BEYOND THE FORWARD AND DWG. NO. 3MKB-10G LOOKING FWD. AFTER ENDS OF THE PREFORMED BOW STRINGERS, AND SHALL SECTION AT STA. 6 NOTE: BUSHING(S) (TYPE OPTIONAL MAY BE INSTALLED IN THE RUDDER TUBE. NOTE: REFER TO DWG. 3MKB-9G OVERLAP THE BONDING PLIES OF THE FORWARD BULKHEAD. SECTION H-H (RUDDER/SKEG) FOR KEEL SHAPE & BOLT LOCATION. CONSTRUCTION PLAN NOTE: REFER TO RULE 3.3.3. FOR LIMITATIONS ON FLOORBOARDS. SCALE: 1:2 (HALF SIZE) SCALE: 1:10, FULL SIZE, HALF SIZE DATE: DEC. 9, 1981 DRAWN/APPROVED: TSL/