DOCSLIB.ORG

ASA106 Instructions Page 1

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
ASA106 Instructions Page 1 ASA106 Instructions Page 1 Place the hull of the Cape Horn in the stand. Carefully unroll the sail set and remove the bowsprit. At the front of the ship slide the bowsprit under Forestay the brass brace and into the wood terminal. Top shroud 1. Attach the bow line to the tip of the underside of the bowsprit Side shrouds 3. Place the large end of the mast into the maststep. At the top of the mast the forward side of the mast has one eye hook, aft has two eyes. 2. Attach the lines on either side of the bowsprit Forestay line is attached at the top aft of the mast. to the eyes on the port and starboard sides of the Fasten the other end to the eye at the tip of the hull. bowsprit. Top shroud lines are attached at both sides of the mast top and pass through the spreader. Fasten the ends of the lines to the aft shroud eyes on the deck. Side shrouds - these thick lines are attached to the mast just below the spreader. Fasten S hooks at the ends of the lines to fore and aft shroud eyes on the deck. Run the adjustment device up each line until it is taut. 4. Twist open the mast rings so they may fit around the mast pole. The Netherlands United States Authentic Models BV Authentic Models, Inc. Ambachtsweg 37 888 Garfield NL-3899 AM P.O. Box 21710 Zeewolde Eugene, OR 97402 ASA106 Instructions Page 2 1 2 #3 connects to 3 hardware on spanner Pass line through guide eyehook 6. Haul Up the Main Sail: Connect the line from the mast's spar in the order Two eyehooks indicated above. Place S hooks 1 and 2 in the eyes on the mast's aft side. Connect #3 S hook to the other hook on the crossbar spreader. Pass the line through the fairlead guide eye and down the mast. Attach the S hook the end of the line to eye on the eye on the port side of the mast just above the boom eyehook. 5. Connect Main Sail to Mast: Pass the metal rod at the end of the mainsail's spar through the two eyehooks on the aft side of the mast directly below the spreader. Hoist the main by attaching the S hook of the block to one of the hooks at spreader's aft. Run the line down the mast and attach to the eye on the starboard side of the maststep. Tighten the line by running the adjustment device up the line until taut. The Netherlands United States Authentic Models BV Authentic Models, Inc. Ambachtsweg 37 888 Garfield NL-3899 AM P.O. Box 21710 Zeewolde Eugene, OR 97402 ASA106 Instructions Page 3 Secure main sale Close mastrings line around the mast Connect Boom preventer Backstay shroud Attach hook Maststep portside 7. Place the boom's hook in the eye on the aft side of the mast as illustrated. Connect the Preventer: The hook at the top of the block connects to the eye on the underside of the boom. The S hook at the end of the Preventer's line connects to the eye on the aft side of the mast. Loop the mast rings around the mast and twist closed. 8. Attach backstay shrouds: The lines are attached port and starboard from the side shroud eye on the mast to the side shroud eye on the aft end of the deck. Trim the sheet: use the block and tackle at the stern of the deck to hold down the end of the boom. Attach the S hook on the block to the eye on the underside of the boom. Starboard Backstay Shroud eyes Shroud eye Bow Stern Fore Aft Shroud eyes Backstay Port Shroud eye The Netherlands United States Authentic Models BV Authentic Models, Inc. Ambachtsweg 37 888 Garfield NL-3899 AM P.O. Box 21710 Zeewolde Eugene, OR 97402 ASA106 Instructions Page 4 2 Two eyes Fairlead guide eye 1 4 5 3 10. Rigging the Clubfooted Sail: 1. Fore end of sail attaches to eye at mid bowsprit. 2. S hook on block at top of sail connects to spanner 9. Gaff Sail (Keeper): Pass the long wire hooks on fore. both spars of the gaff sail through the sets of twoe 3. Run the sail line down the mast to eye at fore eyes at the top of the mast and on the main sail of maststep. spar. Pass the Keeper's line through the fairlead eye 4. Hook unattached end of clubfoot into bowsprit then down the mast. Attach the S hook to the eye terminal. at the port side of the maststep. 5. Attach S hook of the block from deck to eye on clubfoot. The Netherlands United States Authentic Models BV Authentic Models, Inc. Ambachtsweg 37 888 Garfield NL-3899 AM P.O. Box 21710 Zeewolde Eugene, OR 97402 ASA106 Instructions Page 5 2 1 Second jib here 3 4 3 1 11. Second Jib Sail 1. Attach the S hook at the fore end of the sail to the 2nd eye on the bowsprit. 2 2. Attach the top of the sail by hooking the S on the block to the eye on the mast above the spreader. 3. Run sail line down mast, connect it to the eye parallel with the boom. Run adjustment device up the line until taut. 4. The middle corner connects to the line from the deck (see next illustration). 12. First Jib Sail 1. Attach the top of the sail (with short line) to the eye at the top of the mast (fore side). 2. Attach the opposite end of the sail to the fore most eye on the bowsprit. Run adjustment device First jib up the line until taut. line Second jib 3. Attach the S hook from the appropriate deck line line to the corner of the sail. Clubfoot line The Netherlands United States Authentic Models BV Authentic Models, Inc. Ambachtsweg 37 888 Garfield NL-3899 AM P.O. Box 21710 Zeewolde Eugene, OR 97402.
Load more

Recommended publications
  • The Junk Rig Glossary (JRG) Version 20 APR 2016
    The Junk Rig Glossary (JRG) Version 20 APR 2016 Welcome to the Junk Rig Glossary! The Junk Rig Glossary (JRG) is a Member Project of the Junk Rig Association, initiated by Bruce Weller who, as a then new member, found that he needed a junk 'dictionary’. The aim is to create a comprehensive and fully inclusive glossary of all terms pertaining to junk rig, its implementation and characteristics. It is intended to benefit all who are interested in junk rig, its history and on-going development. A goal of the JRG Project is to encourage a standard vocabulary to assist clarity of expression and understanding. Thus, where competing terms are in common use, one has generally been selected as standard (please see Glossary Conventions: Standard Versus Non-Standard Terms, below) This is in no way intended to impugn non-standard terms or those who favour them. Standard usage is voluntary, and such designations are wide open to review and change. Where possible, terminology established by Hasler and McLeod in Practical Junk Rig has been preferred. Where innovators have developed a planform and associated rigging, their terminology for innovative features is preferred. Otherwise, standards are educed, insofar as possible, from common usage in other publications and online discussion. Your participation in JRG content is warmly welcomed. Comments, suggestions and/or corrections may be submitted to [email protected], or via related fora. Thank you for using this resource! The Editors: Dave Zeiger Bruce Weller Lesley Verbrugge Shemaya Laurel Contents Some sections are not yet completed. ∙ Common Terms ∙ Common Junk Rigs ∙ Handy references Common Acronyms Formulae and Ratios Fabric materials Rope materials ∙ ∙ Glossary Conventions Participation and Feedback Standard vs.
    [Show full text]
  • Sailing Trans-Atlantic on the USCG Barque Eagle
    PassageRite of Sailing Trans-Atlantic On The USCG Barque Eagle odern life is complicated. I needed a car, a bus, a train and a taxi to get to my square-rigger. When no cabs could be had, a young police officer offered me a lift. Musing on my last conveyance in such a vehicle, I thought, My, how a touch of gray can change your circumstances. It was May 6, and I had come to New London, Connecticut, to join the Coast Guard training barque Eagle to sail her to Dublin, Ireland. A snotty, wet Measterly met me at the pier, speaking more of March than May. The spires of New Lon- don and the I-95 bridge jutted from the murk, and a portion of a nuclear submarine was discernible across the Thames River at General Dynamics Electric Boat. It was a day for sitting beside a wood stove, not for going to sea, but here I was, and somehow it seemed altogether fitting for going aboard a sailing ship. The next morning was organized chaos. Cadets lugged sea bags aboard. Human chains passed stores across the gangway and down into the deepest recesses of the ship. Station bills were posted and duties disseminated. I met my shipmates in passing and in passageways. Boatswain Aaron Stapleton instructed me in the use of a climbing harness and then escorted me — and the mayor of New London — up the foremast. By completing this evolution, I was qualified in the future to work aloft. Once stowed for sea, all hands mustered amidships.
    [Show full text]
  • Spinnakers and Poles/Bowsprits Explained
    SPINNAKERS AND POLES/BOWSPRITS EXPLAINED The RORC Rating Office is sometimes asked whether symmetric and asymmetric spinnakers are rated differently, and whether there is a rating increase if you use both types. The question is often prompted by the IRC application form asking questions about the spinnakers of each type carried aboard, rather than just the largest spinnaker area (SPA) and total number of spinnakers. There are two aspects of downwind sail rating: the sail itself and the type of pole (if any) it is set on - as explained below. Text in italics is taken from the IRC 2018 Rule text. SPINNAKERS For the calculation of your rating, IRC considers the largest spinnaker area (SPA) and the total number of spinnakers carried. 21.6 Spinnakers 21.6.1 Boats carrying more than three spinnakers in total on board while racing will incur an increase in rating. 21.6.2 Spinnaker area (SPA) shall be calculated from: SPA = ((SLU + SLE)/2) * ((SFL + (4 * SHW))/5) * 0.83 SLU, SLE, SFL and SHW of the largest area spinnaker on board shall be declared. The calculated area of this spinnaker will be shown on a boat’s certificate as the maximum permitted SPA. 8.10.1 Values stated on certificates for LH, Hull Beam, Bulb Weight, Draft, x, P, E, J, FL, MUW, MTW, MHW, HLUmax, HSA, PY, EY, LLY, LPY, Cutter Rig HLUmax, SPA, STL are maximum values. Are symmetric or asymmetric spinnakers rated differently? Not directly, but see the section on pole type below. Is there a rating increase if I carry both symmetric and asymmetric spinnakers? Not directly, but see the section on pole type below.
    [Show full text]
  • December 2007 Crew Journal of the Barque James Craig
    December 2007 Crew journal of the barque James Craig Full & By December 2007 Full & By The crew journal of the barque James Craig http://www.australianheritagefleet.com.au/JCraig/JCraig.html Compiled by Peter Davey [email protected] Production and photos by John Spiers All crew and others associated with the James Craig are very welcome to submit material. The opinions expressed in this journal may not necessarily be the viewpoint of the Sydney Maritime Museum, the Sydney Heritage Fleet or the crew of the James Craig or its officers. 2 December 2007 Full & By APEC parade of sail - Windeward Bound, New Endeavour, James Craig, Endeavour replica, One and All Full & By December 2007 December 2007 Full & By Full & By December 2007 December 2007 Full & By Full & By December 2007 7 Radio procedures on James Craig adio procedures being used onboard discomfort. Effective communication Rare from professional to appalling relies on message being concise and clear. - mostly on the appalling side. The radio Consider carefully what is to be said before intercoms are not mobile phones. beginning to transmit. Other operators may The ship, and the ship’s company are be waiting to use the network. judged by our appearance and our radio procedures. Remember you may have Some standard words and phases. to justify your transmission to a marine Affirm - Yes, or correct, or that is cor- court of inquiry. All radio transmissions rect. or I agree on VHF Port working frequencies are Negative - No, or this is incorrect or monitored and tape recorded by the Port Permission not granted.
    [Show full text]
  • Sail Tuning Guide LINK
    DF 65 Dragonforce 65 Tuning Guide Phil Burgess M - 0413 200 608 E - [email protected] 1st July 2020 A+ A B C Estimated wind range - depends on wave action and tacking ability 0 - 10 kts 8 - 15 kts > 15 kts > 20 kts Distance from Jib Pivot Eyelet to front of Mast (Can also use gate control as a ram to induce mast bend without line 4th Line Line Aft Mast Gate 3rd 5th Max changing forestay). (175 mm) (176 mm) (177 mm) (178 mm) A+ From backstay crane hole to top of backstay hook 951 mm. 785 mm. 698 mm. 620 mm. A, B, C From top of Forestay tang to top of backstay hook. Mast Rake From soft to firm as wind Slightly firmer backstay & Firmer backstay & tight Firmer backstay & tight builds tight forestay forestay forestay Tension Backstay so Mast bend matches Mainsail luff, so sail Mast Bend easily flops from side to side when tilted Soft settings Match luff round Match luff round Match luff round At centre of Jib Boom deepest point 20-25 mm, 15-20 mm 15-20 mm 10-15 mm Boom Outhaul Sail 15 mm at top of range At centre of Main Boom deepest point Depth 25-30 mm, 15-25 mm 15-20 mm 10-20 mm 15 mm at top of range Jib - from Mast centre to end of Jib Boom. Place small mark on deck 38-43 mm 40-45mm 40-45mm 40-45mm Boom - Close Main - from centreline at end of Main Boom. (Adjust Tx for hauled exponential adjustment for last 20 mm sheet travel for high and low pointing mode) 8-15 mm 10-20 mm 15-25 mm 15-25 mm Jib - from Centre of Mast to leech at mid point of jib leech.
    [Show full text]
  • Build Your Own S/V Denis Sullivan Schooner
    Build Your Own S/V Denis Sullivan Schooner Materials: Directions: n Recyclable Materials: Collect building materials and supplies. ● Body (Hull) of the schooner: 1 aluminum foil, egg cartons, Before building, fill in the blanks on the S/V Denis Sullivan on next page. Label plastic bottle, carboard, etc. 2 the following parts of the schooner: ● Sails: Paper, Tissues, Paper (*Answer Key can be found at the Introduction: Towel, etc. bottom of the Activity Sheet) The S/V Denis Sullivan is the only re- ● Mast and Bowsprit: Skewers, a. Sails (Upper and Lower) creation of a 19th century Great Lakes Cargo Schooner and Wisconsin’s Flagship. Build Chopsticks, Pen, Pencils, b. Raffee Sail Schooner Straws, etc. you own S/V Denis Sullivan Schooner with c. Jib Sails (Head Sails) recyclable materials found in your home. n Pencil/Pen d. Pilot House n Paper for drawing design e. Hull Think About It: n Scissors What does a schooner look like? A sailboat n Tape/Glue f. Mast with a minimum of 2 masts that can have Denis Sullivan Denis Sullivan g. Bowsprit up to 7 with the foremast slightly shorter than the mainmast. A schooner usually has Design and draw a schooner with fore-and-aft rigged sails, but may also have 3 pencil and paper. square-rigged sails. Construct the body (hull) of the Do Ahead of Time: 4 schooner. n Gather all supplies Draw and cut out the sails using n To Take It Further: Fill testing 5 scissors. Make at least 3 sails, one Build Your Own S/V Build Your container with enough water so that for each mast, and at least one sail the boat can float freely and cannot for the bowsprit.
    [Show full text]
  • Marshall 22 Catboat T’S Hard to Pinpoint Exactly What Drew Me to a Centerboard Up, Onto the Soft Sands of Cape Cod Where Catboat, and Specifically a Marshall 22
    Welcome to SAILING Magazine’s annual guide to retrofitting, where we chronicle theoretical refits of three boats readily available on the used-boat market. The projects described are typical for boats of this age and type, and the scope and pricing reflect what a retrofit would actually cost. MARSHALL 22 CATBOAT t’s hard to pinpoint exactly what drew me to a centerboard up, onto the soft sands of Cape Cod where catboat, and specifically a Marshall 22. Perhaps it we might spend the night sleeping under the stars on was some romantic notion conjured from gazing at the 10-foot-wide deck. an Edward Hopper or Winslow Homer painting, or But I set out to find a Marshall 22 in need of a Imaybe it was because these boats seem to exude a retrofit. And no, I wasn’t in the market for a project simple elegance. boat requiring complete restoration and carpentry skills The idea of sailing with a single sail was intriguing, found only in legendary boatyards. as was the prospect of exploring shallow bays where a It helped to know a bit about the history of Marshall full-keel sloop certainly would run aground. I envisioned Marine and the late Breck Marshall, the designer and bringing the hull, which draws a mere 2 feet with the builder who founded the company in the early 1960s Originally published in December 2014/ January 2015 issue of SAILING Magazine. All rights reserved. May not be copied, printed or distributed without written permission from SAILING Magazine. Copyright © 2015 by SAILING Magazine.
    [Show full text]
  • ANSWERS to Goddard Sailing Association
    ANSWERS to Goddard Sailing Association (Chesapeake Bay) online-test QUESTION 1: Identify the following parts of a sailboat below: centerboard forestay port shroud tabernacle toping lift boom vang painter winch starboard boom mast tiller A. Boom B. Forestay C. Shroud D. Mast E. Winch F. Centerboard G. Tabernacle H. Tiller I. Topping lift J. Painter K. Port L. Starboard M. Boom vang QUESTION 2: Identify the following sails and parts of a sail below: luff leach clew bow batten head tack foot mainsail stern telltale jib A. mainsail B. jib C. clew D. tack E. head F. leach G. luff H. foot I. batten J. telltale K. stern L. bow QUESTION 3: Match the following items found on a sailboat with one of the functions listed below. mainsheet jibsheet(s) halyard(s) fairlead rudder winch cleat tiller A. Used to raise (hoist) the sails HALYARD B. Fitting used to tie off a line CLEAT C. Furthest forward on-deck fitting through which the jib sheet passes FAIRLEAD D. Controls the trim of the mainsail MAINSHEET E. Controls the angle of the rudder TILLER F. A device that provides mechanical advantage WINCH G. Controls the trim of the jib JIBSHEET H. The fin at the stern of the boat used for steering RUDDER QUESTION 4: Match the following items found on a sailboat with one of the functions listed below. stays shrouds telltales painter sheets boomvang boom topping lift outhaul downhaul/cunningham A. Lines for adjusting sail positions SHEETS B. Used to adjust the tension in the luff of the mainsail DOWNHAUL/CUNNINGHAM C.
    [Show full text]
  • Sailing Course Materials Overview
    SAILING COURSE MATERIALS OVERVIEW INTRODUCTION The NCSC has an unusual ownership arrangement -- almost unique in the USA. You sail a boat jointly owned by all members of the club. The club thus has an interest in how you sail. We don't want you to crack up our boats. The club is also concerned about your safety. We have a good reputation as competent, safe sailors. We don't want you to spoil that record. Before we started this training course we had many incidents. Some examples: Ran aground in New Jersey. Stuck in the mud. Another grounding; broke the tiller. Two boats collided under the bridge. One demasted. Boats often stalled in foul current, and had to be towed in. Since we started the course the number of incidents has been significantly reduced. SAILING COURSE ARRANGEMENT This is only an elementary course in sailing. There is much to learn. We give you enough so that you can sail safely near New Castle. Sailing instruction is also provided during the sailing season on Saturdays and Sundays without appointment and in the week by appointment. This instruction is done by skippers who have agreed to be available at these times to instruct any unkeyed member who desires instruction. CHECK-OUT PROCEDURE When you "check-out" we give you a key to the sail house, and you are then free to sail at any time. No reservation is needed. But you must know how to sail before you get that key. We start with a written examination, open book, that you take at home.
    [Show full text]
  • The Way of the Sea
    1 The Way of the Sea Cheney Duvall stared up at the great clouds of soaring sail, though her eyes watered from the sun and salt sting. The Brynn Annalea had found a tail of the northeast trade winds, strong and hot, to wend her fast down Baja and push her easily over the Tropic of Cancer. Her sharp prow knifed the water, the jib with the lucky shark’s fin mounted on it splashing in the wave crests. She was a beautiful thing, fast, sharp-hulled, streamlined, proud. And dangerous. Cheney shouted up at Shiloh, and he was shouting back down at her. Neither of them could possibly hear the other, but both of them kept on. “You idiot! Come down from there this instant! You are going to fall and die!” Cheney shrieked. He made an impatient gesture—Get below, you dumb girl!— which made Cheney’s heart almost stop, for he had let go with one arm to make jabbing “get below” motions to her. Twelve seamen were perched along the bucking, straining yard, feet kicked back against the footrope, bellies pressed against the yard, hands gathering up the heavy canvas. Cheney watched, horrified, as they struggled to roll the great main royal sail around the yard. Finally it was wound as neatly as thread on a spool, and the sailors, with strong and agile movements, passed lengths of rope around sail and yard and made it fast with hitches. One by one they started edging back along the yard, making for the weather shrouds to scamper down.
    [Show full text]
  • 7180 Rudder Angle Indicator Manual
    7180 Rudder Angle Indicator Owner’s Operation, Installation & Maintenance Manual February 2019 Kobelt Manufacturing Co. Ltd. 7180 Rudder Angle Indicator Kobelt Manufacturing Co. Ltd. NOTES: RECORD DATA BEFORE INSTALLATION FOR FUTURE REFERENCE Model #: Serial #: Date of Purchase: Date of Installation: Rev B MNL_7180 2 of 24 7180 Rudder Angle Indicator Kobelt Manufacturing Co. Ltd. TABLE OF CONTENTS 1 Introduction ............................................................................................................ 4 1.1 Contact .................................................................................................................... 4 1.2 Safety ....................................................................................................................... 4 2 Product Description ................................................................................................. 6 2.1 Technical Data ......................................................................................................... 7 3 Operation ................................................................................................................ 8 4 Installation .............................................................................................................. 9 4.1 Mechanical .............................................................................................................. 9 4.2 Electrical ................................................................................................................ 10 5 Commissioning
    [Show full text]
  • Training Manual
    Offshore Sailing 34.2 TRAINING MANUAL Intentionally Blank CONTENTS RAFSA(O) HR 34.2 TRAINING MANUAL Chap Subject Page - Contents I Introduction iii 1 Storm Sail Rigging 1 - 1 2 Rigging the Preventer 2 - 1 3 Reefing 3 - 1 4 Man Overboard Techniques 4 - 1 • Returning to the Survivor 4 - 1 • • MOB Recovery 4 - 1 • o Boat Hook 4 - 6 o Lasso 4 - 6 o Boarding Ladder 4 - 8 o Halyard Lift 4 - 9 o Handy Billy 4 - 9 o Boom & Mainsheet Lift 4 - 11 5 Adjusting Backstay Tension 5 - 1 6 Poling Out the Headsail 6 - 1 7 Spinnaker Hoisting, Flying and DroPPing 7 - 1 8 Anchoring 8 - 1 i Mar 20 Intentionally Blank ii Mar 20 INTRODUCTION 1. The Purpose of this Training Manual is to set out in more detail how to conduct specific evolutions when oPerating RAFSA(O) HR 34.2 yachts at sea. This Manual suPPlements RAFSA(O)’s Safety Management Policy and our SOPs; it forms a critical component of the RAFSA(O) Document Set. 2. Suggested amendments should be forwarded to the Training PrinciPal at [email protected] There is nothing new in sailing – a few thoughts to ponder “He who loves practice without theory is like the sailor who boards ship without a rudder and compass and never knows where he may cast.” Leonardo da Vinci "The pessimist complains about the wind; the optimist expects it to change; the realist adjusts the sails." William Arthur Ward "The wind and the waves are always on the side of the ablest navigator." Edmund Gibbon “The good seaman weathers the storm he cannot avoid, and avoids the storm he cannot weather.” Anon iii Mar 20 Intentionally Blank iv Mar 20 CHAPTER 1 - STORM SAIL RIGGING 1.
    [Show full text]