DOCSLIB.ORG

Fang™ Hd Crossbow Owner's Guide

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Fang™ Hd Crossbow Owner's Guide FANG™ HD OWNER’S GUIDE ® FANG™ HD CROSSBOW OWNER’S GUIDE PRO PACKAGE ™ ™ ® FANG HD OWNER’S GUIDE ® FANG HD OWNER’S GUIDE Thank you for purchasing your new PSE crossbow! With proper use and WARRANTY care your crossbow will provide years of enjoyment. Keep this manual PSE makes no other warranty claims whether expressed or implied. This with your crossbow for reference. warranty applies to the original owner only, and does not cover cables, strings, or vibration dampers. PSE FANG™ HD SPECIFICATIONS ** SPEED: Up to 405 FPS KINETIC ENERGY: 134 FT LBS DRAW WEIGHT: 205 LBS NOTE: This manual covers only the Fang HD crossbow model. If this is MASS WEIGHT: 7.3 LBS the incorrect manual for your crossbow model, please contact POWER STROKE: 14.5” AXLE-TO-AXLE: 18” PSE Customer Service. LENGTH: 35 ½” SAFETY TRIGGER: AUTO SAFETY & ADF ** The speed rating for the Fang HD crossbow was taken using a 370 grain crossbow 1) ALWAYS treat your crossbow as you would any weapon or firearm. bolt. The package though will include 400 grain bolts. It is a powerful weapon that can be deadly if mishandled. Your Fang HD crossbow comes with the Pro Package which includes 2) ALWAYS keep your crossbow pointed in a safe direction. Never point the following items. your crossbow at anything you don’t intend to shoot. • HDV-425 1.5-5X32 VARIABLE ZOOM ILLUMINATED RETICLE SCOPE • ADJUSTABLE BUTTSTOCK 3) NEVER enter a vehicle with a loaded crossbow. Always uncock and • FOOT STIRRUP properly stow your crossbow for transporting. • LIMB DAMPENERS & STRING SUPPRESSORS 4) ALWAYS check your crossbow to make sure that it is in proper • 5-BOLT HUNTER LT QUIVER mechanical order. Check for damaged, worn, loose or missing parts. • 3-22” THUNDER BOLTZ (400 GRAINS WITH BULLET POINTS) • DUAL STRING STOPS 5) NEVER DRY FIRE YOUR CROSSBOW. Firing the crossbow • RAIL LUBE without a bolt will cause damage not only to the crossbow but • PSE SLED COCKING WINCH DEVICE possible bodily injury to you and anyone in the area. It also voids the warranty. LIMITED LIFETIME WARRANTY 6) DO NOT make changes or alterations to any parts of this crossbow as it may cause an unsafe condition and will void the warranty. PSE warranties every compound crossbow to be free of defects in 7) NEVER release the safety on your crossbow until you are ready to material and workmanship for the period as defined below. shoot and are sure of your target. 8) NEVER shoot any bolt or other projectile from your crossbow that 1) PSE crossbow stocks, metal prods and cams, if defective, will be has not been recommended by PSE. Use only bolts of the proper replaced at no charge for the size, weight and length. lifetime of the product. 9) ALWAYS keep your fingers and thumb out of the path of the string 2) Limbs, if defective, will be replaced at no charge for the first year, and cables while shooting your crossbow. Failure to do so will cause and a $50.00 surcharge for the lifeof the product. injury. 3) Evidence of mishandling, abuse or modification of the product or 10) ALWAYS wear safety glasses when handling a crossbow. use of non-PSE replacement parts voids the warranty. 4) Cables, strings, cable slides, and vibration dampers are wearable items and are not covered by this warranty. WARNING: Use extreme caution while operating this weapon. Never run, crawl, All warranty work will be performed by PSE or your local PSE ride a horse, operate an ATV, motorcycle or travel in a vehicle with a Crossbow dealer. loaded crossbow. Accidental discharge could prove harmful or fatal. WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov 2 ™ ™ FANG HD OWNER’S GUIDE ® FANG HD OWNER’S GUIDE Thank you for purchasing your new PSE crossbow! With proper use and WARRANTY care your crossbow will provide years of enjoyment. Keep this manual PSE makes no other warranty claims whether expressed or implied. This with your crossbow for reference. warranty applies to the original owner only, and does not cover cables, strings, or vibration dampers. PSE FANG™ HD SPECIFICATIONS ** SPEED: Up to 405 FPS KINETIC ENERGY: 134 FT LBS DRAW WEIGHT: 205 LBS NOTE: This manual covers only the Fang HD crossbow model. If this is MASS WEIGHT: 7.3 LBS the incorrect manual for your crossbow model, please contact POWER STROKE: 14.5” AXLE-TO-AXLE: 18” PSE Customer Service. LENGTH: 35 ½” SAFETY TRIGGER: AUTO SAFETY & ADF ** The speed rating for the Fang HD crossbow was taken using a 370 grain crossbow 1) ALWAYS treat your crossbow as you would any weapon or firearm. bolt. The package though will include 400 grain bolts. It is a powerful weapon that can be deadly if mishandled. Your Fang HD crossbow comes with the Pro Package which includes 2) ALWAYS keep your crossbow pointed in a safe direction. Never point the following items. your crossbow at anything you don’t intend to shoot. • HDV-425 1.5-5X32 VARIABLE ZOOM ILLUMINATED RETICLE SCOPE • ADJUSTABLE BUTTSTOCK 3) NEVER enter a vehicle with a loaded crossbow. Always uncock and • FOOT STIRRUP properly stow your crossbow for transporting. • LIMB DAMPENERS & STRING SUPPRESSORS 4) ALWAYS check your crossbow to make sure that it is in proper • 5-BOLT HUNTER LT QUIVER mechanical order. Check for damaged, worn, loose or missing parts. • 3-22” THUNDER BOLTZ (400 GRAINS WITH BULLET POINTS) • DUAL STRING STOPS 5) NEVER DRY FIRE YOUR CROSSBOW. Firing the crossbow • RAIL LUBE without a bolt will cause damage not only to the crossbow but • PSE SLED COCKING WINCH DEVICE possible bodily injury to you and anyone in the area. It also voids the warranty. LIMITED LIFETIME WARRANTY 6) DO NOT make changes or alterations to any parts of this crossbow as it may cause an unsafe condition and will void the warranty. PSE warranties every compound crossbow to be free of defects in 7) NEVER release the safety on your crossbow until you are ready to material and workmanship for the period as defined below. shoot and are sure of your target. 8) NEVER shoot any bolt or other projectile from your crossbow that 1) PSE crossbow stocks, metal prods and cams, if defective, will be has not been recommended by PSE. Use only bolts of the proper replaced at no charge for the size, weight and length. lifetime of the product. 9) ALWAYS keep your fingers and thumb out of the path of the string 2) Limbs, if defective, will be replaced at no charge for the first year, and cables while shooting your crossbow. Failure to do so will cause and a $50.00 surcharge for the lifeof the product. injury. 3) Evidence of mishandling, abuse or modification of the product or 10) ALWAYS wear safety glasses when handling a crossbow. use of non-PSE replacement parts voids the warranty. 4) Cables, strings, cable slides, and vibration dampers are wearable items and are not covered by this warranty. WARNING: Use extreme caution while operating this weapon. Never run, crawl, All warranty work will be performed by PSE or your local PSE ride a horse, operate an ATV, motorcycle or travel in a vehicle with a Crossbow dealer. loaded crossbow. Accidental discharge could prove harmful or fatal. WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov 3 ™ ™ ® FANG HD OWNER’S GUIDE ® FANG HD OWNER’S GUIDE Illuminated Reticle Scope Rope Cocking Groove String Stop Prod Assembly Bolt Retention Spring Integrated Stock/Barrel Adjustable Stock Trigger Fig. 1a Assembly Ambidextrous Safety Lever Bolts Cam Foregrip Finger Safety Guard Foot Stirrup 5-Bolt Limbs Quiver Fig. 1 Before assembling your crossbow (Fig. 1), please check to see if all crossbow parts are included: 1-Prod Assembly, 1-Stock, 3-Crossbow Bolts, 1-Scope, (Fig. 1a) 1-Sled Winch Cocking Device, 1-Prod Bolt,2-Allen Wrenches, 1 Prod/Stock Connection Fig. 2 Guard w/ adhesive pad, 1-Cable slide, 1-Foot Stirrup w/set screws,1-Quiver, 1-Quiver Mount w/screws and 1-Rail Lube (not shown). If any of these parts are missing please contact PSE Customer Service. Attach cable slide to the cables with the concave area facing up and the cables in the two grooves as shown. Fig. 2 Peel cover from the adhesive side of the Prod/Stock connection pad and attach it to the prod side of the joint. Fig 3a. Slide the Prod/Stock connection guard onto the prod. Fig 3b. Connect the prod and the stock by inserting the cable slide* and cables into the slot on the front of the stock as shown in Fig. 4. (Be sure the concave side is facing up to match with the contour on the inside of the barrel. NOTE: Prod WILL NOT be flush to the stock.) Fig. 3b Push the cables into the track and position the prod for connection to the stock using the prod bolt and hex key provided. As you tighten prod bolt, the prod will become flush with the stock. Fig 5. Install and tighten the center set screw to lock in prod bolt. Insert the foot stirrup into the two holes on the front of the prod. Make sure the two grooves in the foot stirrup are facing towards the set screws used to secure the stirrup. (Inset) Tighten set foot stirrup set screws. Fig 6. * NOTE: Cable damage WILL occur if you do not use the slide. Any damage incurred due to improper set-up will not be covered by your warranty. 4 Fig. 5 ™ ™ FANG HD OWNER’S GUIDE ® FANG HD OWNER’S GUIDE Rope Cocking Groove Adjustable Stock Fig.
Load more

Recommended publications
  • On the Mechanics of the Bow and Arrow 1
    On the Mechanics of the Bow and Arrow 1 B.W. Kooi Groningen, The Netherlands 1983 1B.W. Kooi, On the Mechanics of the Bow and Arrow PhD-thesis, Mathematisch Instituut, Rijksuniversiteit Groningen, The Netherlands (1983), Supported by ”Netherlands organization for the advancement of pure research” (Z.W.O.), project (63-57) 2 Contents 1 Introduction 5 1.1 Prefaceandsummary.............................. 5 1.2 Definitionsandclassifications . .. 7 1.3 Constructionofbowsandarrows . .. 11 1.4 Mathematicalmodelling . 14 1.5 Formermathematicalmodels . 17 1.6 Ourmathematicalmodel. 20 1.7 Unitsofmeasurement.............................. 22 1.8 Varietyinarchery................................ 23 1.9 Qualitycoefficients ............................... 25 1.10 Comparison of different mathematical models . ...... 26 1.11 Comparison of the mechanical performance . ....... 28 2 Static deformation of the bow 33 2.1 Summary .................................... 33 2.2 Introduction................................... 33 2.3 Formulationoftheproblem . 34 2.4 Numerical solution of the equation of equilibrium . ......... 37 2.5 Somenumericalresults . 40 2.6 A model of a bow with 100% shooting efficiency . .. 50 2.7 Acknowledgement................................ 52 3 Mechanics of the bow and arrow 55 3.1 Summary .................................... 55 3.2 Introduction................................... 55 3.3 Equationsofmotion .............................. 57 3.4 Finitedifferenceequations . .. 62 3.5 Somenumericalresults . 68 3.6 On the behaviour of the normal force
    [Show full text]
  • Making Arrows Ronald A
    Fact Sheet 6 Making Arrows Ronald A. Howard Jr.* Many archers enjoy making increase arrow mass. Wooden been exposed to the graphite their own arrows because it shafts must be lacquered or fibers. Those fibers are hard, allows them to exercise painted full length to protect stiff and fine. They survive personal quality control, add them from moisture. cooking well and can cause injury if swallowed. Many special features, personalize the Fiberglass shafts are lighter than target archers, particularly arrows in other ways or add to wooden shafts of the same spine those shooting bows equipped their shooting enjoyment. weight. They remain relatively with overdraws, prefer graphite Making arrows involves straight, and they can be matched shafts. several steps, but it is not in spine and arrow mass much difficult. High quality arrows better than wooden shafts. Aluminum shafts have been the can be made with care and Although fiberglass is a tough standard of both target archers attention to detail. material, these shafts are subject and bowhunters for many Shaft Selection to splitting on impact. They also years. The shafts can be made tend to shatter or splinter if to very close tolerances in a The first step is selecting the variety of alloys, offering easy shaft type and size desired. struck along their length. Shafts with internal damage may even matching in spine and weight. Arrow shafts are available in Aluminum shaft materials may wood, fiberglass, graphite, shatter during a release. Fiberglass has been an excellent be obtained in inexpensive soft aluminum and graphite- alloys that are easily bent or aluminum combinations.
    [Show full text]
  • Coaches Manual
    Lviv State University of Physical Culture named after Ivan Boberskyj Department of shooting and technical sports Subject "Theory and Methodology of the Selected Sport and Improvement of Sports Skill – archery" for 4 courses students LECTURE: "TERMINOLOGY / GLOSSARY IN ARCHERY" by prof. Bogdan Vynogradskyi Lviv – 2020 TERMINOLOGY / GLOSSARY Actual draw length: The personal draw length Barrelled arrow: An arrow that has a greater of the archer measured at full draw, from the cross section in the middle and tapers down at bottom of the slot in the nock to the pivot point both ends. of the grip plus 1 3/4 inch (45mm), which is the Basic technique: The fundamental technique of back edge (far side of the bow) on most bows. shooting a bow and arrow. Usually the style Actual arrow length: The personal arrow taught during the introduction to archery, length of the archer, measured from the bottom forming the basis for consistent shooting. slot of the nock to the end of the shaft (this Belly (of bow): The surface of the bow facing measurement does not include the point/pile); the archer during shooting. Also known as the with this end of the shaft at 1 inch (25mm) in “face” of the bow. front of the vertical passing through the deepest point of the bow grip or the arrow rest. Black: The fourth scoring colour on the Indoor/Outdoor target face, when counting from Actual draw weight: The energy required to the centre of the target. draw the bow to the actual draw length (commonly measured in pounds).
    [Show full text]
  • The Arrow Shafts Is Pseudosasa Japonica Or Commonly Called Japanese Arrow Bamboo
    The Japanese Arrow By Godai Katsunaga Intorduction The Ya, or arrow of Japan and was between 34 and 38 inches in length, made of fire hardened bamboo shafts and had a steel arrow head., During this period and earlier arrows used in combat were often marked to identify who owned them, this allowed samurai to get the proper credit for killing an opponent. Period Construction The bamboo used for the arrow shafts is Pseudosasa japonica or commonly called Japanese arrow bamboo. This bamboo grows in slender culms that are packed tightly together, forming a dense hedge, with large, dark green foliage. It is a tough and versatile bamboo that will thrive in shade and in sun while growing to about 15 foot tall and was common throughout Japan. Farmers and other workers harvested the bamboo in the early winter when the plants saps were down. To get the required diameter need to make arrows the plants that were between two and three years in age were preferred. After harvesting, the best bamboo was hand selected and ideally stored for about a year for drying, allowing most of the moisture in the plant material to evaporate. Preparation of each shaft included having the nodes shaved off and then softening the shaft by placing it in hot sand prior to straightening it by hand. After the shafts were straightened, they were exposed to high heat to remove any remaining moisture and harden the natural sugars, creating a stronger bond of the natural fibers; this was known as fire hardening. Fletching was done with hawk, eagle, crane or pheasant tail feathers and could be either three or four flights depending on the arrow head that would be mounted.
    [Show full text]
  • World Crossbow Shooting Association - TARGET, STANDARD, FREESTYLE & MEDIEVAL CROSSBOW RULES
    World Crossbow Shooting Association - TARGET, STANDARD, FREESTYLE & MEDIEVAL CROSSBOW RULES WORLD CROSSBOW SHOOTING ASSOCIATION SHOOTING RULES FOR TARGET, MEDIEVAL, STANDARD, FREESTYLE CROSSBOWS AND GENERAL SHOOTING RULES. EFFECTIVE 1st January 2019 Effective, 1st January 2019 Page: 1 World Crossbow Shooting Association - TARGET, STANDARD, FREESTYLE & MEDIEVAL CROSSBOW RULES INDEX Clause Item Page No INDEX ................................................................................................................................................................................. .................. 2 DEFINITIONS ...................................................................................................................................................................................... 6 SECTION 1. WORLD CHAMPIONSHIPS, REGINAL CHAMPIONSHIP, JUDGING, RECORDS, ASSISTED SHOOTERS 1 PRECEDENCE, INTERPRETATION AND AMENDMENTS ..................................................................................................... 9 2 WORLD CHAMPIONSHIPS ...................................................................................................................................................... 9 2.1 Outdoor Target ................................................................................................................................................................ 2.2 3D ...................................................................................................................................................................................
    [Show full text]
  • By Peter Dell ' O Rto and S Ean Punch
    BY P ETER D ELL’ORTO AND S EAN P UNCH Written by PETER DELL’ORTO and SEAN PUNCH Additional Material by VOLKER BACH and C.J. CARELLA Edited by SEAN PUNCH Cover Art by BOB STEVLIC Illustrated by ABRAR AJMAL and BOB STEVLIC ISBN 978-1-55634-762-7 1 2 3 4 5 6 7 8 9 10 STEVE JACKSON GAMES Committed Attack . 99 Defensive Attack. 100 Evaluate . 100 Feint . 100 ONTENTS Ready . 101 C Who Draws First?. 103 Move . 105 Realism Level . 29 INTRODUCTION . 4 Move and Attack . 107 Beginning Students as PCs. 30 Publication History . 4 Wait . 108 About the Authors . 4 CHARACTER TEMPLATES . 31 ADDITIONAL COMBAT OPTIONS . 109 Del Duque (350 points) . 33 Melee Attack Options . 109 1. HISTORY . 5 Frauds . 35 A Matter of Inches . 110 Adrian Froste (200 points) . 37 TIMELINE . 6 Untrained Fighters . 113 Kai Lian (250 points) . 39 ASIA . 8 Close-Combat Options. 114 China . 8 ADVANTAGES, DISADVANTAGES, Teeth. 115 Xia . 8 AND SKILLS . 42 Grab and Smash! . 118 Monks and Martial Arts . 9 Advantages . 42 Ranged Attack Options . 119 India . 10 Desirable Advantages . 43 Rapid Fire with Thrown Weapons. 120 Northern vs. Southern Kung Fu . 10 Chi Powers for Martial Artists . 46 Active Defense Options . 121 Religion, Philosophy, and Fists . 11 Perks . 49 Harsh Realism for Indonesian Archipelago. 12 Disadvantages. 53 Unarmed Fighters . 124 Japan . 12 Common Disadvantages. 53 CINEMATIC COMBAT . 125 Ryu . 12 Skills . 54 Multiple Attacks . 126 Ninja: Legend vs. History . 13 Combat Skills . 55 Chambara Fighting . 128 Korea. 14 Wildcard Skills for Styles . 60 Mind Games . 130 Other Nations.
    [Show full text]
  • Tenpoint Crossbow Technologiestm OWNER's General Instruction Manual
    TenPoint Crossbow TechnologiesTM OWNER’s GENERAL INSTRUCTION MANUAL To prevent injury to yourself or others, or damage to your crossbow, read this manual along with all other operating and safety instructions included in your crossbow package before assembling, loading or using the crossbow. THIS MANUAL COVERS: Safety Instructions 1-3 Cocking & Loading 3-4 Unloading Your Crossbow 4 Using the Correct Arrow 5-6 Sighting Your Crossbow 6-9 Crossbow Maintenance & Care 9-10 Crossbow Troubleshooting 10-12 Returning Your Crossbow for Service 12 String & Cable Adjustment Chart 13 String & Cable Specifications 14 Notes 14 Limited Operational Warranty 15 TenPoint Crossbow Technologies® 1325 Waterloo Road Mogadore, OH 44260-9608 330.628.9245 www.tenpointcrossbows.com WARNING: (READ FIRST) To prevent injury to yourself or others, or damage to your crossbow, read this manual along with all other operating and safety instructions included in your crossbow package before assembling, loading or using the crossbow. SAFETY INSTRUCTIONS Follow these strict and absolute safety rules when cocking, loading, pointing, and shooting your crossbow. • Install the GripGuard on thumbhole-style stocks prior to sighting-in or shooting your crossbow (not applicable on the Vapor or Stealth SS). DANGER Note: If you have misplaced or lost the GripGuard, contact TenPoint at www.tenpointcrossbows.com or by calling 330-628-9245 immediately for a replacement. • Never allow your fore-grip hand’s fingers or thumb to move above the barrel’s flight deck or into the bowstring or cables’ release path (photos 1, 2 & 3). If you do, you will injure yourself severely when you fire your crossbow.
    [Show full text]
  • Blazer Vanes How to Remove Arrow Wraps Cleaning Arrow Shafts
    Here are the answers to the most commonly-asked questions about Bohning Archery products, including information about fletching arrows, fletching Blazer vanes, the Bohning Blazer jig, arrow wraps, quiver topics, and more. If you have a question that isn't answered here, please contact us for assistance. Blazer Vanes Do Blazer vanes work with broadheads? Blazer vanes are designed to be used with fixed and mechanical broadheads. They also work very well with field points and can be used for target shooting. How should Blazer vanes be fletched? Blazer vanes should be fletched in the same location as any other vane. We recommend a three-degree right helical, using our Blazer Helix Jig or Helix Tower Fletching Jig ™; or a two-degree offset, using our Pro-Class Fletching Jig. How to Remove Arrow Wraps What are the best ways to remove ArroWraps brand arrow wraps from a shaft? There are different options for removing ArroWraps: • Soak the ArroWrap in hot tap water for 5 minutes, and then peel it off. • Heat the ArroWrap with a hair dryer and then peel it off. • Scrape the ArroWrap off the shaft using Bohning's Stripper tool. Always clean the shaft well after removing an ArroWrap. How can vanes or feathers be replaced without damaging a shaft that has an ArroWrap brand arrow wrap or crest? Unfortunately, vanes or feathers cannot easily be replaced without damaging the crest. Cleaning Arrow Shafts What is the best method for cleaning arrow shafts? Clean arrow shafts by scrubbing with an abrasive pad (such as Scotch Brite®), using water and a good degreasing soap, such as Bohning SSR Arrow Shaft Surface Cleaner.
    [Show full text]
  • Archery for All the Real Benefits of Inclusivity Berkshire Archery Association Hidden History Brought to Light
    Official Magazine of Archery GB SUMMER 2021 | £4.95 BRITISH 3D Championships Rovers return to Pentref Archery for all The real benefits of inclusivity Berkshire Archery Association Hidden history brought to light SPECIAL Preparing for REPORT The Game Fair Discounted entry offer for AGB members Ragley Hall, 23-25 July TOKYOINTERNATIONAL JUDGES TALK THROUGH THEIR ROLES INSIDE: Compound • Getting archery-fit • Kit care • Griffin vane giveaway 2021 new MXT-10 www.wiawis.com l www.win-archery.com 2021 new META DX 2021 new ACS EL -- TRUETRUE- - SMOOTHNESS! SMOOTHNESS! MOSTMOST STABILITYSTABILITY &ACCURACY!&ACCURACY! -- BESTBEST SHOOTINGSHOOTING FEELING!FEELING! SUMMER 46 2021 NEWS/FEATURES News 06 A joyful return to the range, Big Reopening report, Big Weekend RIGHT: plans, new AGB strategy details, Day in the club round-up and more life of our RDO Mailbag 76 34 Have your say 58 Club Spotlight 36 Bowbrook Archers on their latest achievements History 38 The way we wore – clothing changes on the field Judge and jury ARCHERY GB Three international judges talk 40 through their roles ahead of the Day in the life Tokyo Games 58 Meet Toby Andrews, Regional Archery for all PRACTICAL Development Officer 46 A look at the sport’s accessibility Rule changes as told by the archers who know Latest updates How to 33 British 3D 62 Run a beginners’ course Directory Championships How to get in touch 52 Return to sport 80 Wet weekend in Wales went Chartered physiotherapist down a storm 66 Nicky Hunt on how to Berkshire Archery safely rebuild your form 40 55 Association
    [Show full text]
  • Download 2021 Catalog
    ® 2021 CATALOG ® Bohning Manufacturing Facilities Over 42,000 sq ft in the heart of the northern Michigan woods NORTH PLANT ® Since 1946, the Bohning Company LTD has proudly designed CONTENTS and manufactured some of the most innovative and successful 2 Featured Products arrow accessories from the same location in Lake City, Michigan. As we enter our 75th year of operation, the passion to continue 6 Vanes the tradition remains stronger than ever. We stand proudly with our customers, distributors, and sales partners, while supporting archery organizations world-wide. This milestone anniversary is 14 Wraps made possible by you; the archer, dealer, distributor, media and sales partners, who have graced us with your trust for 75 years. 16 Nocks The Bohning story started when Rollin Bohning, a chemist, family 18 Fletching Jigs man, and archer sought to solve the issue of broadhead to arrow adhesion in 1946. That same year Ferr-L-Tite® was created 20 Premium Points and, after extensive work with Fred Bear and Doug Easton, it was perfected. Seventy-five years later, Ferr-L-Tite remains the 24 String Care industry standard. 29 Adhesives We are a privately owned and operated company, manufacturing products which have earned the title “most successful and widely 31 Accessories used in the world”. Throughout the past seven decades, we have produced items for the archery, Christmas tree, fishing, and agricultural industries. 40 Crossbow Here at Bohning innovation is expected, delivered, and driven 42 Traditional by a team of dedicated people who live and work in a place of natural beauty, where wildlife is abundant and peace of mind is 48 Apparel just a dirt road away.
    [Show full text]
  • Tenpoint Catalog FA
    2002 Catalog Patented Superior Design Components Innovation & Materials • Patent No. 5,553,596, (VIBRA-CUSH™) • Aircraft grade machined aluminum Crossbow Vibration Damping Device • Aircraft grade extruded aluminum • Patent No. 5,598,829, (DFI™) Crossbow Dry Fire Prevention Device • Investment castings ® • Patent No. 5,649,520, (PowerTouch™ Trigger) • Hardcoated & Teflon impregnated Crossbow Trigger Mechanism aluminum surfaces • Patent No. 5,987,724, (SuperBrite™) • Pultruded Fiberglass Limbs Crossbow Bolt Cap and Fletching • Engineered Polymer Components Nock Device and Method • Fast Flight™ Strings & Cables • Patent No. 6,095,128, (ACUdraw™) Crossbow Bowstring Drawing Mechanism • Stainless Steel Assembly Screws • Patent No. 6,286,496 B1, (ACUdraw™) Crossbow Bowstring Drawing Mechanism We started our company in January 1994, proudly displaying our distinctive plaid logo, underscored with our company slogan, ...the mark of perfection. Back then the slogan was a statement of intention – what we wanted to achieve. Today, we focus our product development energy toward... the pursuit of perfection. There are three components to that focus: patented design innovation, superior components & materials, and advanced manufacturing methods. 2 Advanced Core Manufacturing Performance Methods Features • CNC Machining The Foundation Of Every • Injection Molding Crossbow We Make. • Precision Laser Cutting Every TenPoint™ crossbow is made with the core performance features listed below. These • Laser Engraved Graphics features insure accuracy, dependability, and • Investment Casting overall performance from model to model. • Fluid Imaged Camouflage While our top-of-the-line models (TURBO • State-of-the Art Surface Coating Extreme,™ MAGNUM X-2,™ & STEALTH X-2™) include additional features and offer more power and speed, all models are equally dependable and accurate.
    [Show full text]
  • Sophia's Journal Teacher Guide
    ! ! Teacher’s Companion Guide for Sophia’s Journal ! ! Welcome t te Sophia’s Journal Teacher’s Guide! Tis guide has been developed in cooperaton wit te autor, who wrot Sophia’s Journal t bring American histry alive in a way tat speaks t students’ hearts, not just te circle-filing lobe of teir half tst-taking cortx, and t demystf Islam and Muslims for te average student. Te curriculum-enhancing actvites in te guide are calibratd t increase students’ knowledge of histrical contxt and improve teir comprehension, critcal tinking, writng, artstc expression and cooperaton skils. Each chaptr contains objectves, vocabulary, facts t share, discussion points and actvites. Tese suggestons for broadening students’ experience of reading te book can be cherry- picked, modified and added t in order t suit each individual classroom. If you have any questons or suggestons, please don’t hesitat t contact us at [email protected]. ! ! ! Sophia’s Journal Teacher Guide Overview: The following material is assembled in hopes of “Giving rise to women’s voices.” It is designed with an eye toward diversity in young adult books. Overall Objective of Teaching Packet: To acquire attitudes which are essential for citizens of democratic pluralist societies, in particular intellectual honesty, open-mindedness, respect for truth, tolerance, acceptance of differences, empathy and civil courage. Standards Common Core Language Arts Standards National Social Studies Standards ! ! Reading Informational Text: Culture & Diversity Key Ideas and Details • Assist learners to explore, CCSS.ELA-LITERACY.RI.5.1 comprehend, and apply critical Refer to details and examples in a text information, ideas, and concepts when explaining what the text says that are common across societies, explicitly and when drawing inferences social institutions, cultures, and from the text.
    [Show full text]