Installation Instructions 55 Series Electric Strike

Total Page:16

File Type:pdf, Size:1020Kb

Installation Instructions 55 Series Electric Strike 801 Avenida Acaso, Camarillo, Ca. 93012 • (805) 494-0622 • www.sdcsecurity.com • E-mail: [email protected] INSTALLATION INSTRUCTIONS 55 SERIES ELECTRIC STRIKE 55-ABC Universal Strike Pak for 55-A for cylindrical locksets 55-B / 55-C For mortise 55-D / 55-E / 55-F for mortise multiple cylindrical and mortise Grade 1 or equivalent. locksets with up to a 3/4" latch locksets with latch and deadbolt lockset applications. INSTALLATION SDC 55 Series heavy duty electric strikes are designed 1. Verify lock compatibility, refer to page 2 and Fig. 6, page 4. for use with cylindrical and mortise locksets and mortise 2. For proper frame preparation, refer to template drawings, exit devices. Several faceplate configurations eliminate Fig. 4 & 5, page 4. the need for centerline relocation, making them perfect 2. Factory supplied in Failsecure mode. For Failsafe mode refer for new or retrofit construction. to Fig. 2, page 3 3. Determine minimum wire gauge required. See wire gauge chart below. FEATURES: 4. CAUTION! Before connecting power wires check for proper operating Non-handed voltage at opening with a volt meter. Voltage must be within +/- 10% No Centerline relocation of strike operating voltage for proper operation. Up to 3/4” latch and 1” deadbolt 5. Configure strike for 12 or 24VDC operation. Refer to pigtail power 1/8”Horizontal alignment adjustment connector wiring in Fig. 1, Page 3. Connect wires to power source. Field selectable Fail-Safe/Fail-Secure 6. To install the strike into the frame opening: Field selectable 12/24VDC A) Position the wiring either down or up or toward the back of the Stainless steel, corrosion resistant hollow metal frame. Make sure wires are completely clear of strike, Tamper resistant heavy duty construction so they are not pinched when mounting strike in the frame. Plug-in connector B) Insert mounting screws through the faceplate and secure into Fits ANSI 115.1 frame prep. with face modification mounting tabs. 7. After installation check horizontal alignment. There should be 1/32” Patent pending allowable movement when the door is pulled toward the keeper. 8. ALIGNMENT ADJUSTMENT: Loosen mounting screws, shift strike body behind faceplate horizontally as shown in Fig. 3A, page 3, OPTIONAL MONITORING OUTPUTS: then tighten mounting screws. LCM (Keeper Deadlocked Monitor) 9. For excessive horizontal alignment issues, remove shim filer bar from Signals keeper is closed and deadlocked and/or unlocked. the keeper as shown in Fig. 3B, page 3 LBM (Latch Bolt Monitor) 10. The Electric Door Strike MUST be installed in such a way and in such a Signals latch is extended into strike and/or retracted. location so as not to impair the operation of an emergency exit or panic DBM (Deadbolt Monitor) hardware mounted on the door. Signals deadbolt is extended into strike and /or retracted. Strike Input - Minimum Wire Gauge Requirements Warnock Hersey Tested according to: Voltage 100 ft 150 ft 200 ft 250 ft 300 ft UL 10C, 3 Hr Fire Rated (Fail-Secure only). 12VDC 18 Ga 16 Ga 14 Ga 14 Ga --- UL Tested according to: UL 1034 Burglary-Resistant 24VDC 18 Ga 18 Ga 18 Ga 16 Ga 16 Ga Monitoring outputs: Minimum 22 Gage wire recommended OPERATION: Fail-Secure (Power-to-Unlock): Unlocked when energized. Fail-Safe (Power-to-Lock): Locked when energized. Unlocked Locked when de-energized and during power failure. when de-energized and during power failure. Application: For non fire rated and fire rated doors (exception, Application: Non-fire rated doors only. may not be used on stairwell doors). May not be maintained in CAUTION: Fail-safe is not permitted with the UL Fire Door the unlocked (energized) state when used with fire rated doors. Accessory label. P:\INSTALLATION INST\ELECTRIC STRIKES\INST-55\INST-55.vsd REV F 02-19 Page 1 55 SERIES ELECTRIC STRIKE UNIVERSAL APPLICATION KITS Strike body and faceplate(s) provided as shown below. Order strike bodies and different faceplates separately Faceplates are interchangeable and may be ordered separately. to accommodate all applications. Model Lockset Application Compatible Locks Operation 55-ABC Universal Strike Pak • Adaptable to all 55-A, 55-B, 55C • Grade 1 or equivalent applications listed below. Latchbolt 9/16" – 3/4” After releasing the latchbolt, the • 5 strike body and faceplates keeper returns to the locked position. • All mortise locksets listed • For new and retrofit installation with 55-B & 55-C • No relocation of the centerline. 55-A • Grade 1 or equivalent After releasing the latchbolt, the • Bored (Cylindrical) locks. Latchbolt 9/16" – 3/4” keeper returns to the locked • No relocation of the centerline. • Adams Rite 4720 ANSI and position. compatible narrow stile locks. 55-B • Mortise locksets and exit devices • Accurate • Falcon with or without a deadlatch located • Arrow • Marks below the latchbolt. After releasing the latchbolt, the • Best • Sargent keeper returns to the locked position. • For new and retrofit installation • Corbin Russwin • Yale • No relocation of the centerline. • Dorma 55-C • Mortise locksets and exit devices with or without a deadlatch located • SDC above the latchbolt. • Baldwin After releasing the latchbolt, the • Hager keeper returns to the locked position. • For new and retrofit installation • Schlage • No relocation of the centerline. 55-D • Mortise locksets with a deadbolt and a deadlatch located below • Accurate • Falcon When the deadbolt is projected the latchbolt. • Arrow • Marks manually, the strike will not release. When the deadbolt is retracted, • Deadbolt will not release. • Best • Sargent • Corbin Russwin • Yale access is accomplished by • For new and retrofit installation • Dorma electrically releasing the keeper. • No relocation of the centerline. 55-E • Mortise lockset with a deadbolt. When the deadbolt is projected manually, the strike will not release. • Deadbolt will not release. • Baldwin When the deadbolt is retracted, • For new and retrofit installation access is accomplished by electrically releasing the keeper. • No relocation of the centerline. 55-F • Mortise locksets with a deadbolt When the deadbolt is projected and a deadlatch located above manually, the strike will not release. the latchbolt. • SDC • Schlage When the deadbolt is retracted, access is accomplished by • For new and retrofit installation • Hager electrically releasing the keeper. • Deadbolt will not release. P:\INSTALLATION INST\ELECTRIC STRIKES\INST-55\INST-55.vsd REV F 02-19 Page 2 FIG. 1 WIRE DIAGRAM - 55 SERIES ELECTRIC STRIKE Power SDC 12/24V Pigtail P/N CA-55-4 ACCESS CONTROL Connector 12V/600mA 24V/300mA Fail-Safe + 12 or 24V STRIKE Red + Red + Fail-Secure _ DC Black _ White MOV Power Supply Cable 1 Cable 2 - NOTE: Power wires must not be connected AC to DC Rectifier SDC BR64XL to supply wires larger than 18AWG + RED + Monitoring ~ ~ YEL ~ 12 or 24V Connectors -WHT - AC ORG/BLK N/C (Powered = Open) YEL ~ Transformer WHT/BLK LCM COM * YEL/BLK N/O (Powered = Closed) * ORG N/C (Latched = Open) Strike Input: Dual Voltage WHT LBM 600 mA @ 12VDC YEL COM N/O (Latched = Closed) 300 mA @ 24VDC ORG/RED N/C (Bolt Thrown = Open) Contacts: SPDT, Dry, 5 Amp @ 30V WHT/RED DBM COM YEL/RED * NOTE: LCM Contacts Reversed N/O (Bolt Thrown = Closed) When in Failsafe Mode HIGH SECURITY DOOR SECURE MONITORING: LCM & LBM Required LCM & LBM wired in series indicates door is closed, latched and strike is deadlocked or door is open or unlocked FAIL SECURE MODE –Door Secure or Unlocked Status FAIL SAFE MODE –Door Secure or Unlocked Status YEL/BLK ORG/BLK WHT/BLK WHT/BLK COM LCM COM LCM ORG/BLK YEL/BLK N/O N/O N/C N/C ORG ORG WHT LBM WHT LBM YEL YEL FIG. 2 FIELD REVERSIBLE FIG. 3 HORIZONTAL ALIGNMENT ADJUSTMENT FAILSAFE / FAILSECURE 3A-Nominal Alignment: Loosen mounting screws. Failsecure Mode: Factory supplied, Failsecure Shift strike body behind the faceplate horizontally. Failsafe Mode: Remove cover, push solenoid toward Tighten mounting screws. end of strike as shown below. 3B-Excessive Alignment Issues: Remove shim filler bar from keeper. Remove Cover 3A 3B Failsecure Shown Failsafe P:\INSTALLATION INST\ELECTRIC STRIKES\INST-55\INST-55.vsd REV F 02-19 Page 3 FIG. 4 FRAME PREPARATION – 55 Electric Strike FIG. 5 STRIKE DIMENSIONS CENTER LINE OF STRIKE AND LOCK, AND LOCK BOLT SHOULD ALIGN HORIZONTALLY 2X TAP FOR #12-24 UNC THDS THRU .250 (1/4”) 1.688 (1-11/16”) CL 3.375 4.875 (3-3/8”) (4-7/8”) +.015 +.015 3.625 -.000 -.000 (3-5/8”) .375 +.015 (3/8”) -.000 CL .625 4.125 5/8” (4-1/8”) .005 .625 5/8” .734 1.250 1-1/4” +.015 -.000 2X 5/32” MTG TAB DEPTH (TYP) 47/64” STANDARD ANSI FIG. 6 FACE PLATES – All faceplates are interchangeable for application requirements 55-A 55-B 55-C 55-D 55-E 55-F 7/8" 7/8" 7/8" 1-3/4" 2-5/16” 2-5/8" 2-31/32" 2 x 1-3/8" 1- 3/8" 5/8" 1-3/8" 7/8" 1/8" 3-1/4" 1-3/8" 3/8" 2x7/8" P:\INSTALLATION INST\ELECTRIC STRIKES\INST-55\INST-55.vsd REV F 02-19 Page 4.
Recommended publications
  • HES Electric Strikes & Accessories
    2012 Catalog HES Electric Strikes & Accessories ASSA ABLOY, the global leader in door opening solutions 0000 Series Our History. For more than 35 years, HES currently markets quality HES electric Hanchett Entry Systems, Inc.® (HES) has been strikes and accessories and extra-heavy duty, first to market with cutting edge solutions like commercial grade Folger Adam Electric Door the 8500 concealed electric strike for mortise Controls® products. locksets, the versatile 1006 Series, and the Our Customers Come First. Above all else, surface-mounted, windstorm-rated 9600. HES believes in meeting the needs of our Headquartered in Phoenix, Arizona, customers with products that solve their HES is a leading manufacturer of electric specific needs. We continually evaluate the strikes and locking devices for the access way we do business to assure this goal is durable, control industry. We are committed to being met. Our success has been built on providing electromechanical locking solutions listening to you—and delivering products high- and support that create safety, security and and services that help advance your business. peace of mind for our customers. We value long-term relationships with our quality suppliers and sales partners, seeking out An Industry Leader. Backed by the strength groups that command respect in their local electric of ASSA ABLOY, the global leader in door markets and operate with the highest level opening solutions, HES continues to grow, of professionalism. strikes leading the industry in quality, service and innovation. Our new, eco-friendly, LEED Silver On behalf of our entire team, thank you for designed building features improved energy using HES products.
    [Show full text]
  • Von Duprin Electric Strikes Features Brochure
    Electric strikes Safety, performance and quality you can trust At critical moments of life safety, Von Duprin® gives you the confidence of knowing that the products you count on will perform. Von Duprin electric strikes have been designed and tested to the highest standards in the industry to provide the assurance of quality and reliability. You can turn to Von Duprin for expertise and service at any time before, during or after installation. We offer a full line of electric strikes to accommodate a wide range of door preps and locking hardware. Whether you’re deploying an electric strike in a standalone setting or as part of a comprehensive access control system, Von Duprin electric strikes are an ideal solution. Our broad portfolio includes electric strikes with a wide range of factory configurable options for new construction and specialized applications, as well as field-configurable options to fit your aftermarket needs. 4200 2 Ideal for interior applications such as Series a doctor’s office entrance that requires visitor management and traffic control. 1 ® Schlage KP2000E standalone keypad 1 2 Von Duprin PS902 power supply 4 Traffic control 3 Von Duprin 4211 electric strike 3 Affordable option for commercial 4 Schlage AL Series lock applications 5 5 Schlage 621 pushbutton Field configure power failure mode without disassembling the strike AFTERMARKET APPLICATIONS Cylindrical lockset applications 5100 2 Series Simple and cost effect way to add standalone access control to perimeter openings such as employee entrances. 1 Schlage KP212
    [Show full text]
  • Distributor of ASSA ABLOY Products
    February 2017 ASSA ABLOY AUTHORIZED CHANNEL PARTNER Distributor of ASSA ABLOY products www.dugmore.com [email protected] Phone: 888-384-6673 Fax: 888-329-3846 1 Table of Contents page 3 SARGENT Harmony & Corbin Russwin Access 600 page 4 SARGENT Profile & Corbin Russwin Access 800 page 5 SARGENT Passport 1000 (P1/P2) & Corbin Russwin Access 700 (PIP1/PWI1) page 6 SARGENT Passport 1000 (PG) & Corbin Russwin Access 700 (PAC1) page 7 SARGENT & Corbin Russwin SE LP10 page 8 SARGENT & Corbin Russwin IN120/IN220 page 9 SARGENT & Corbin Russwin IN100 page 10-12 Adams Rite trim & electric strikes page 13-16 HES electric strikes & accessories page 17 Securitron & Alarm Controls power supplies page 18-22 Pro-Lok installation tools page 23 Just Door Toolz installation tools page 24-33 Major Mfg installation tools page 34 Electro Lynx page 35-36 Fire Door Accessories page 37 Don Jo page 38 Crown Door Products page 39 GKL products page 40 Misc Items www.dugmore.com [email protected] Phone: 888-384-6673 Fax: 888-329-3846 2 H1 28 10G271 LL 26D 24V TCRNE1 CL33605 NZD M802 626 24V H2 28 10G271 LL 26D 24V TCRNE1 CL33605 NZD M812 626 24V M802 - Prox M812 - iClass H1 - Prox H2 - iClass Corbin Russwin Access 600 series SARGENT Harmony series cylindrical lock with cylinder override, 10 Line cylindrical lock with 24V, fail secure, NZD lever & rose in dull cylinder override, 24 volts, fail chrome finish. secure, L lever, L rose, dull Wiegand compatible access control chrome finish. systems. Wiegand compatible access Built-in door status monitoring.
    [Show full text]
  • Poe SOLUTIONS Power Over Ethernet
    PoEPower over SOLUTIONS Ethernet Capable Locking Hardware PoEPower over SOLUTIONSEthernet Capable Locking Hardware POWER Security Door Controls SDCsecurity.com 1.800.413.8783DATA SDCsecurity.com 1.800.413.8783 The Future of Security The world is wired. Internet cable is everywhere. Buildings are smart. Imagine the savings in cost and installation time not having long cable runs and power supplies for every door by simply tapping into the nearest Ethernet connection. SDC’s low power line of PoE Capable Locking Hardware and Access Controls does just that by allowing easy integration and connection to an access control system using ordinary Ethernet cable in a PoE enabled network. SDC’s PoE Solutions are the same robust, reliable and quality Electric Locks, Devices, and Access Controls we’ve been making for over 40 years. Now we’ve ensured they work in low power PoE environments where energy effciency, fexibility and green and sustainable requirements reach all the way to electronic hardware and locks for controlling door openings. Complementing our PoE solutions is our new IP ProTM IP-based Access Control Series – to help bridge the gap between traditional locking hardware and IT networks. IP ProTM is a Professional Grade ProTM Door Access Control SolutionTM to control a single door – easy Controller expandable - with everything needed for a complete, IP door access control system. (see page 9 for full description) Now, there’s a simple way to install, expand and control door access control with PoE Solutions. Smart products designed for smart buildings and smarter people…now. Only from SDC. Magnetic Locks EMLock® 1500 Series SDC’s patented EMLock® design represents the pinnacle of magnetic lock evolution.
    [Show full text]
  • Von Duprin Guide to Selecting an Electric Strike Brochure
    Guide to selecting an electric strike With so many electric strikes on the market today identifying the right solution can seem like an overwhelming task. This brief guide highlights some important considerations when making your selection. Allegion security and safety consultants are here to help you every step of the way. You can turn to us for expertise and service at any time before, during or after installation. Openings which do not function properly from a mechanical perspective cannot effectively carry out their mission as access control points. Door misalignment and sag should be identified and corrected before access control is deployed. Likewise, worn or misaligned hinges should be addressed to prevent damage to the door and frame. Your door closer must also be strong enough to allow for proper latching. 1. Application Electric strikes are a cost effective alternative for Figure 1 Quick survey applications where electrified lock mechanisms are not practical. What makes electric door strikes Define the application and different from traditional lock strike plates is the operational requirements movable keeper. The keeper interacts with the latch Keeper bolt of the lockset or panic hardware, either securing Identify the application: it to lock the door, or allowing the latchbolt to be Aftermarket pulled through the keeper for access. New construction When selecting a strike, begin by defining the Heavy duty application and operational requirements. For Medium duty example, you may have a perimeter door with an entry buzzer or emergency Traffic control exit doors connected to the fire alarm system. Regardless of the application, Von Duprin offers a full portfolio of electric strikes to address it.
    [Show full text]
  • FSH Locking Electromechanical Security New Generation Electric and Electronic Locking
    FSH LOCKING Electromechanical Security NEW GENERATION ELECTRIC AND ELECTRONIC LOCKING FSH MISSION FSH Fire & Security Hardware, is an Australian owned company who pride in and strive to maintain their leading position in the Australian electromechanical security locking market. FSH recognises and acknowledges the relationships with their Distribution Partners to which FSH endeavours at all time to provide competitively priced high quality solutions to most if not all electromechanical security locking solutions. FSH is cognisant of the growing support of Consultants and Advisors in the Security Industry who are now specifying FSH devices as their product of preference. FSH also acknowledge our End Users who demand Quality, Service and Expert Support and who recognise this in their growing demand for the FSH product lines. FSH commits to continue with its leadership in innovation of Security Locking Devices: To maintain its reputation as the leading producer of high quality locking products: and to maintain its aggressive price competitiveness. FSH - a proud Australian Owned Company. FSH HEADQUARTERS | MATRAVILLE NSW FSH STATE-OF-THE-ART TESTING EQUIPMENT NEW GENERATION ELECTRIC AND ELECTRONIC LOCKING INTERNATIONAL MARKETS Our range of Electric Locking Devices have been installed in countless projects throughout the world. As a reference we list below just a few of the diverse buildings and complexes fitted out with them. Universities Hospitals Other Buildings USA Baylor College of Medicine Australia Sydney St George Hospital China Beijing
    [Show full text]
  • Electric Strikes —
    nglisch USA • Stand 07.04.2014 E Layout S. 24 – DORMA CI-2012 • EL ECTRIC STRIK es — Basic, Smoke, Fire, TV 5xx ANSI ES Series DORMA Deutschland GmbH DORMA Americas DORMA Platz 1 DORMA Drive, Drawer AC 58256 ENNEPETAL Reamstown, PA 17567-0411 GERMANY Phone (800) 523-8483 04/14,WN 052 184 Electric 51532, Strikes, GB, x. DMS. xx/14 notice without change to Subject Phone +49 2333 793-0 Fax (800) 274-9724 Fax +49 2333 793-4950 E-mail [email protected] www.dorma.com www.dorma-usa.com DORMA_U4-Adressen_CI-2012.indd 24 07.04.14 09:18 ELECTRIC STRIKes ACC ess AT THE PUSH OF A BUTTON — DORMA electric strikes ensure Whether for standard doors, fire Benefits door security in private, public and smoke check doors or for and commercial premises, are doors in emergency and escape . For over-rebated and . Fail-secure and fail-safe suitable for use with many routes, you will be able to find flush-closing doors models different locks and door Types the right model to match your . Modular construction system . Series Fire 447 and Fire 448 and are available in all particular requirements – ensures flexibility for fire and smoke check conventional operating voltages. all quality-assured by DORMA. Stainless steel strike plates doors with general approval . Adjustable latch ensures covering any position optimal alignment to existing . Holding function, unlocking structural conditions function and monitor contact . Thanks to the Easy Adapt depending on model concept for electric strikes of the series Basic, Basic-Safe, Smoke, Fire 447 and Fire 448 there is no need for disruptive recesses in the door frame for the electric strike latch, so the door seal is left unbroken.
    [Show full text]
  • SDC Catalog Section: 1.3 Locking Devices
    ACCESS & EGRESS LOCKING DEVICES SOLUTIONS 1.3 Electric Strikes 5 6 2 7 4 3 2 1 The lock behind the system SDCSecurity.com 800.413.8783 [email protected] Complete Component Considerations 7 6 1 Locking Device • Electric Strike • Delayed Egress Lock 3 AC • Electric Bolt Lock Mains • Electrifed Lockset • Exit Device • Frame Actuator Lockset 5 • Magnetic Lock EMLock® 1511 Exit Check™ 1511s 1650 lbs Delayed Egress Lock UniFLEX™ 55 1 3 Electra Pro™ Z7200 HiShear® 1565 - 2700 lbs 4 2 Spacesaver® 1091A Selectric Pro™ Z7800 Spectra® 6000 3 • Dual Latch Retraction & Dogging 8 • Delayed Egress • Exit Alarm • Electric Mortise • HiTower® Actuator Standalone 2 Access Control Standalone or Network • Keyswitch • Digital Keypad • Card Reader Entry Check™ IP Pro Entry Check™ EntryCheck™ 704U 920PW IP-based Access Control 918 924P Keyswitch 31. Egress Device • Exit Switch • PIR Egress Sensor • Exit Sense Bar Egress PIR MD31D Sure Exit® PSB560 422U 463U 474U 492 Emergency • Emergency Door Release Door Release • ADA Compliant Solutions CBC484A4U 484A1U & 484O1U Dual Switch Narrow Mullion Bollard Post Push Plate Switch Auto EntryControl™ 482A6U 2 SDC SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM IP Network AC Mains 41. Power Transfer Devices 2 5 Required With Locksets & Exit Devices • Electric Power Hinge • Power Transfer Loop • Concealed Power Transfer 3 PTH-4 PTH-10 PTM-2 1 PT-2U PTM-10 55. Power Supply & Door Controller PC Managed Network • 12/24VDC, Class 2 • Fire release input • System Status LED’s • Multiple Fused Outputs • Multiple Relay Confgurations
    [Show full text]
  • Low Energy Operator D-4990
    PRECISION HARDWARE LOW ENERGY OPERATOR D-4990 TABLE OF CONTENTS Page Page Introduction.................................................................................................2 Standard Applications...............................................................................5 ADA “Blue-Paint” Access ........................................................................2 Typical System Applications ................................................................6, 7 Features/Benefits.......................................................................................3 Architectural Specifications ....................................................................8 Electrical Data Specifications .................................................................4 Technical Details ....................................................................................8, 9 How To Order ..............................................................................................4 Accessories ........................................................................................10, 11 INTRODUCTION Stanley Security Solutions is pleased to offer its latest product line designed to maximize public door accessibility for Americans with Disabilities Act (ADA) Title INTRODUCTION III applications. The D-4990 Low Energy Operator offers Stanley’s newest and most convenient features to gain safe access for ADA applications. ADA is a civil rights law that is intended to guarantee equality for those who are physically handicapped or disabled.
    [Show full text]
  • 55 Series Electric Door Strikes
    UniFLEX™ Spec - Application Specific Faceplates Included Lock Compatibility: To determine compatibility of locksets not listed below. UniFLEX Spec models include strike and faceplate for individual job requirements. Recommend for specifiers and industry professionals for fast and easy specification of individual installation requirements. Model Lockset Application Compatible Locks Operation 55-A • Cylindrical locksets • All cylindrical locksets • Locksets with ANSI centerline with 1/2" to 5/8" latchbolts latch entry lockset with up to IDC - See M7200 Datasheet After releasing the latchbolt, the keep- 3/4" latchbolt er returns to the locked position. • Locksets with ANSI centerline latch entry with up to 3/4" latchbolt 55-B • Mortise locksets and mortise exit devices with or without a • Accurate • Falcon After releasing the latchbolt, the keep- deadlatch located • Arrow • Marks er returns to the locked position. below the latchbolt. • Best • Sargent • Corbin Russwin • Yale • Dorma • Schlage 55-C • Mortise locksets and mortise • IDC - See M7800 Datasheet exit devices with or without a After releasing the latchbolt, the keep- • Baldwin deadlatch located above er returns to the locked position. • Hager the latchbolt. 55-D • Mortise locksets with a deadbolt and a deadlatch located below Deadbolt Retracted: the latchbolt. When signaled by the access control the strike keeper unlocks, permitting • With deadbolt retainer installed, • Accurate • Falcon door latch release. The strike keeper access control will not release • Arrow • Marks returns to the closed and locked projected deadbolt. • Best • Sargent position. The door then returns to the • With deadbolt retainer removed, • Corbin Russwin • Yale closed and locked position. access control will release • Dorma deadbolt. The door will not Deadbolt Retainer Installed close when deadbolt is projected.
    [Show full text]
  • Electric Strikes Fail Locked F2164 F2 Series Fire Rated Offset and Centerline Latch Entry
    Electric Strikes Fail Locked F2164 F2 Series Fire Rated Offset and Centerline Latch Entry In or Out... we make it Easy!® ® Deadbolt Dimensions Plug ANSI 1-1/4”W x 4-7/8”L Adjustable (31.8mm x 123.0mm) Deadbolt Keeper ‘Saw-tooth’ Adjustable Adjustment Deadlatch Locator ‡ Ramp Optional ‘Plug-in’ Features Latch Monitor ‡ • Modular design allows compatibility with most locks without having to order special faceplates ‡ Patent Pending Features • Adjustable deadbolt keeper and deadlatch ramp F2164 Fire Rated Offset • Heavy-duty stainless steel construction with Certifications & Testing 32D finish (Brushed stainless steel) and Centerline Latch Entry • UL 10C, 3 hour fire-rated (fail secure only) • Up to 1500 lbs (680 kg) holding force • UL 1034, burglary-resistant listed This unique, versatile, “all-in-one”, fire • Factory tested to meet ANSI/BHMA 156.31 • Fits HES 1006 (1003) frame cutout rated electric strike combines strength, for strength and endurance • Accommodates ¾” latch projection (1500 lbs holding force) convenience, • Factory tested to exceed 2,000,000 cycles (everything you need is in the box) and • Faceplate and screws included for in an attractive, sleek, easy to install centerline latch entry design. • Unique sliding shim design for up to 1/8” (3mm) horizontal adjustment for What makes this strike unique is the “Saw-tooth Adjustment Locator” design misaligned frames ‡ that allows the installer to move the Accessories • Vertical Adjustability of strike for precise deadbolt keeper, or deadlatch ramp F2LM – Latch Monitor Kit positioning of lockset vertically to align with a wide variety of • Accommodates up to 1” deadbolt* mortise locks with offset latches.
    [Show full text]
  • Catalog 2017/18 Table of Contents 1 7 3 5 11 17 51 15 19 18 37 27 57 53 52 36 39 55 20 46 40
    ROFU CATALOG 2017/18 ROFU ELECTROMAGNETS 8000 SERIES ......................................................... 1 8100 SERIES ........................................................... 3 8400 SERIES 5 ........................................................... TABLE OF CONTENTS 8500 SERIES .......................................................... 7 8600 SERIES ........................................................... 11 8700 SERIES ......................................................... 15 8900 SERIES ........................................................... 17 ACCESSORIES ........................................................ 18 GLASS DOOR ACCESSORIES ............................... 19 ELECTRIC STRIKES 1500 SERIES ............................................................ 20 1400 / 3400 SERIES ............................................... 27 SOLENOIDS ............................................................ 36 1700 SERIES ............................................................ 37 1106 SERIES ........................................................... 39 2400 SERIES ............................................................ 40 EXIT DEVICES 9200 - 9700 SERIES ............................................... 46 9800 SERIES ............................................................ 51 9500 SERIES ............................................................ 52 MISCELLANEOUS ACCESS CONTROL MISC. ACCESS CONTROL ...................................... 53 CONVERTERS / TRANSFORMERS ............................ 55 DOOR CORDS
    [Show full text]