Proxima Steel Forge Private Limited

Total Page：16

File Type：pdf, Size：1020Kb

+91-8048372573 Proxima Steel Forge Private Limited https://www.indiamart.com/proxima-steelforge/ Manufacturer of steel shaft club hammer, hand axe, steel shaft double ended scutch hammer, joiner's warring ton hammer, straight pin hammer, cross pin hammer, ball pin hammers etc. About Us PROXIMA" the company was founded in 1992 with the solid backing of the "SANT" group with decades of experience in the manufacturing field of quality products. Ambitious plans have been made to reach out and market quality products all over the world. The Hand Tools are meticulously made, keeping safety norms foremost in every body's minds. Every effort is made to ensure quality, which is the main indegredient in a Hand Tool. This effort is not easily visible from the appearance. The qualities of steel, good forging, heat treatment and finish can only be proved in use. Striking tools in particular, can be dangerous unless expertly made. Great stress is laid on safety; which is in built in each and every striking tool which leaves the factory to ensure its safe working life, if used for the purpose for which it is intended. For more information, please visit https://www.indiamart.com/proxima-steelforge/aboutus.html HAMMERS P r o d u c t s & S e r v i c e s Maurer Hammer (Berlin Mason'S Club Hammer Pattern) (Brick Chipping) Joiner'S Warrington Hammer Steel Shaft Double Ended Scutch Hammer HAND TOOLS P r o d u c t s & S e r v i c e s Brick Bolsters Steel Shaft Club Hammer With Machine Cut Head Ripping Hammer Slater'S Hammer Din 7239 (Lath Hammer) SLEDGE HAMMERS P r o d u c t s & S e r v i c e s Double Faced Sledge Straight Peen Sledge Hammers Hammers Faustel Sledge Hammer Double Faced Sledge Hammers GARDEN TOOLS P r o d u c t s & S e r v i c e s Hand Weeder Weeding Fork Hand Trowel Transplanting Trowel PLIERS P r o d u c t s & S e r v i c e s Water Pump Plier European / Water Pump Plier (Aligator) American Pattern Slip Joint Combination Plier Cold Chisel AXES P r o d u c t s & S e r v i c e s Gipser Beil (German Axe) Ham Axe Hand Axe BALL PEEN HAMMERS P r o d u c t s & S e r v i c e s Ball Peen Hammers Cross Peen / Ball Peen Hammers Ball Peen Hammers with Steel Shaft CLAW HAMMERS P r o d u c t s & S e r v i c e s Carpenter'S Adze Eye Claw Steel Shaft Claw Hammer Hammer One Piece Forged Claw Hammer OTHER PRODUCTS: P r o d u c t s & S e r v i c e s Engineers Cross Peen Faustel Club Hammers Hammer (Polished Sides) Sledge Hammers F a c t s h e e t Nature of Business :Exporter and Manufacturer CONTACT US Proxima Steel Forge Private Limited Contact Person: DEEPAK VAID B-14, 15, Industrial Focal Point, Phase 2 Jalandhar - 144004, Punjab, India +91-8048372573 https://www.indiamart.com/proxima-steelforge/.

Copy Link

Recommended publications

The Sunday Stab'. Washington P. P„ Mat 30, 1926—Tort 6
AUTO MOB ICES* ETC. THE SUNDAY STAB'. WASHINGTON P. P„ MAT 30, 1926—TORT 6. MISCErCXNBOHS. 3 ETC. FOR SALE—AUTOMOBILES. FOR RENT—GARAGES. BUSINESS OPPORTUNITIES. FOB SALE—MISCELLANEOUS. FOB BALE—MISCELLANEOUS. 1 FOB SALE—MISCELLANEOUS. _ POfiS. PETS. RENT ROOMS—FURNISHED. (Continued.) _ nod.) good PUPPIES, best - (Continued.) . (Continued.) _ (Con tin guitar, «et~(H do*.) Havi- brass gas. for sale; FOX TERRIER wire-haired: ACOtJSTICON. FURNITURE—WaInut bed. double STOVE—Five-burner, reglatered 8533, ' BILTMORE. BUICK coupe, late fine condition: bal- REAR 1616 L ST. CARS. .$40.00 ) WANTED TO BUY—Rooming house: must land china, rack and furniture of 4- bed. complete walnut bookcase, unit aec-1 condition: I7ai at. n.w. Phone Block. Col. Apt. 16—Room for ladv model: ¦ N.W.. 6 hau » *3. 9th Ifit”a, tlve y as loon tires. Rear 1512 L st. n.w 11-59 ) be cheap; part cash; not ovsr 10 rooms. room apartment. Tel. Col. 6145-W. tional bookcase, mahogany pedestals, tables, | North 9166. AIREDALE PUPPIES. 2 months: pedigree**: of™, i furnished bed-living room: 7-passeneer: fine running : Rear 424 L n.w. single oak wardrobe, odd pieces; in good collar, registered beauties; $lB- n 9um mer: warm in quiet: CADILLAC. st. n.w 25.00 ) section. Address Box 12-Z. Star .office. ANTIQUE CENTER TABLE, banquet top, all SUIT, gray. English tweed, raccoon best stock; sls and near, SkZ. Itwo car Winter: enter. Rear 1611 22nd st. n.w 8.60 walnut; princess condition: cheap. 1212 Euclid st. n.w. 31* size $55". sell for Phone Kensington 114-F-12.
[Show full text]
Striking Tools
STRIKING TOOLS Bahco has over 125 years’ experience of forging, and a solid reputation as a high-quality tool manufacturer. Bahco axes, mauls, hammers, cold chisels and punches all meet the high standards that are essential requirements for all applications - where quality, safety, durability and ease of use are key factors. Safety first. In this chapter we also highlight the safety rules that should be followed by the users of our striking tools. 1078 Chapter Index WOODWORKING AND CONSTRUCTION HAMMERS 1082-1084 METAL WORKING AND INDUSTRIAL HAMMERS 1084-1086 INSTRUMENT AND WORKSHOP HAMMERS 1086-1090 AXES, MAULS AND WEDGES 1091-1097 COLD CHISELS 1098-1101 PUNCHES 1102-1108 SETS 1108 WRECKING BARS 1109 MASONS’S PIN 1109 1079 ICON INDEX ▪ Camping axes are lightweight axes with a short ▪ Mauls are heavy sledge hammers that can be handle, making them easy to carry around. Also used to drive poles into the ground or splitting suitable for indoor use e.g. as a kitchen axe wedges into logs ▪ Head weight: 0.6 kg /1 1/4 lb to 1 kg/2 1/4 lb ▪ Head weight: 3 kg/6 ½ lb to 4 kg/8 3/4 lb Camping ▪ Length: 36-50 cm/ 14 1/4” - 19 3/4” Splitting ▪ Length: 90 cm/35 ½” with wedges ▪ Splitting axes have a thick head, specially made ▪ Hatchets are longer axes for trimming trees and for splitting wood. The shape of the head helps other general purpose work to penetrate the wood with little effort. Some are ▪ Head weight: 1 kg/2 1/4 lb made with a longer head back, for use with a ▪ Length: 60-70 cm/23 ½”-27 ½” Splitting splitting wedge Trimming ▪ Head weight: 2 kg/4 ½ lb to 3.5 kg/7 3/4 lb branches ▪ Length: 80-90 cm/31 ½”-35 ½” and felling ▪ Felling axes are heavier, with long handles and a thinner edge, for easy cutting when felling trees ▪ Head weight: 1.1 kg/ 2 ½ lb to 2.3 kg/5 lb ▪ Length: 70-90 cm/ 27 ½” - 35 ½” Felling AXES, MAULS AND WEDGES All axes are supplied with either a leather or rubber edge protector to ensure that the finish of the blade is maintained.
[Show full text]
1. Hand Tools 3. Related Tools 4. Chisels 5. Hammer 6. Saw Terminology 7. Pliers Introduction
1 1. Hand Tools 2. Types 2.1 Hand tools 2.2 Hammer Drill 2.3 Rotary hammer drill 2.4 Cordless drills 2.5 Drill press 2.6 Geared head drill 2.7 Radial arm drill 2.8 Mill drill 3. Related tools 4. Chisels 4.1. Types 4.1.1 Woodworking chisels 4.1.1.1 Lathe tools 4.2 Metalworking chisels 4.2.1 Cold chisel 4.2.2 Hardy chisel 4.3 Stone chisels 4.4 Masonry chisels 4.4.1 Joint chisel 5. Hammer 5.1 Basic design and variations 5.2 The physics of hammering 5.2.1 Hammer as a force amplifier 5.2.2 Effect of the head's mass 5.2.3 Effect of the handle 5.3 War hammers 5.4 Symbolic hammers 6. Saw terminology 6.1 Types of saws 6.1.1 Hand saws 6.1.2. Back saws 6.1.3 Mechanically powered saws 6.1.4. Circular blade saws 6.1.5. Reciprocating blade saws 6.1.6..Continuous band 6.2. Types of saw blades and the cuts they make 6.3. Materials used for saws 7. Pliers Introduction 7.1. Design 7.2.Common types 7.2.1 Gripping pliers (used to improve grip) 7.2 2.Cutting pliers (used to sever or pinch off) 2 7.2.3 Crimping pliers 7.2.4 Rotational pliers 8. Common wrenches / spanners 8.1 Other general wrenches / spanners 8.2. Spe cialized wrenches / spanners 8.3. Spanners in popular culture 9. Hacksaw, surface plate, surface gauge, , vee-block, files 10.
[Show full text]
2016 Affinity Tool Works Dealer Price Book Rev 20 Xlsx
2016 PRODUCT CATALOG Prices Effective January 1, 2016 Supersedes all previously dated price lists. No. 20 Prices subject to change without notice. Affinity Tool Works, LLC • 1161 Rankin • Troy, Michigan 48083 Ph(248) 588-0395 • Fax(248) 588-0623 • [email protected] • www.affinitytool.com Pkg www.boratool.com Stock No. Description Part No. List Price Qty BORA Clamps & Vises 540445 4.5" Micro Bar Clamp (2-Pack) 6$ 10.91 540606-S 6" Midi Pistol Grip Clamp 6$ 12.64 540606 6" Midi Pistol Grip Clamp (2-Pack) 6$ 23.64 540612-S 12" Midi Pistol Grip Clamp 6$ 15.45 540612 12" Midi Pistol Grip Clamp (2-Pack) 6$ 30.00 540806 6" Pistol Grip Bar Clamp 6$ 19.09 540812 12" Pistol Grip Bar Clamp 6$ 20.91 540818 18" Pistol Grip Bar Clamp 6$ 28.18 540824 24" Pistol Grip Bar Clamp 6$ 30.00 BORA Specialized Clamps & Vises 540520 20 Piece Mini Spring Clamp Set 1$ 10.00 551025 Corner Clamp 6$ 30.00 551027 Large Vise 6$ 30.00 BORA Angle Master Miter Duplicator for Mitersaws 530301 Angle Master - Miter Duplicator 3$ 65.45 BORA Sharpening Stones 501057 Sharpening Stone-Aluminum Oxide 6" x 2" x 1" 30$ 4.47 501098 Sharpening Stone-Green Silicon Oxide 6" x 2" x 1" 30$ 8.73 501060 Sharpening Stone-Aluminum Oxide 8" x 2" x 1" 30 $ 8.90 Page 2 © 2016 Affinity Tool Works, LLC Pkg Stock No. Description List Price Qty BORA Modular Clamp Edge & Accessories 543100 100" WTX Clamp Edge (50" + 50") 6$ 99.00 543050 50" WTX Clamp Edge 6$ 53.00 543036 36" WTX Clamp Edge 6$ 46.00 543024 24" WTX Clamp Edge 6$ 40.00 Kits: 543300 3 pc Clamp Edge Set, 24, 36, 50" 4$ 134.00 543400
[Show full text]
2020 Career Development Event Rules and Regulations Regulations
2020 Career Development Event Rules and Regulations Regulations Agricultural Technology and Mechanical Systems Maximum Number of Team Members 4 Number of Team Members Scored 4 Scantron Ag Sales/Fb Mgmt./Ag Mech – CDE# 105481 Committee: Tim Kidwell Wendy Knopp Seth Neal 2020 West Virginia Agriculture Mechanics CDE The 2020 agricultural mechanics contest at the State Agriculture Career Development As voted by teachers of WV events will be modeled closely on the National FFA ATMS CDE. For more information about national CDE: http://faculty.missouri.edu/~schumacherl/natcon.html The yearly suggestions for emphasis are recommendations made by WV teachers at the summer meeting of the ATMS group at State FFA Convention. These will be revisited every year for conformation. MORNING SESSION- 2020 Events –This will be a written test for qualification to the afternoon hands-on section. Students will need a non-programmable calculator. No cell phones will be allowed in the contest. Anyone found using a cell phone at any time during the contest will be removed and scored at a 0 for all portions. Written Test The participant will complete a 25 question multiple choice test that 45 min focuses on questions from each systems area of the event. The exam has a heavy math focus. Students will need a non-programmable calculator. Compact equipment systems The participant will complete a 25 question multiple choice test that 45 min focuses on compact equipment. Compact equipment is defined as Identification of parts and tools being 30 horsepower or less. Interpreting horsepower, torque and will be contained in this system other power measurement criteria.
[Show full text]
Scotvec-Scottish Vocational Education Council
-SQA-SCOTTISH QUALIFICATIONS AUTHORITY Hanover House 24 Douglas Street GLASGOW G2 7NQ NATIONAL CERTIFICATE MODULE DESCRIPTOR -Module Number- 0085301 -Session-1988-89 -Superclass- WK -Title- CARPENTRY AND JOINERY: WORKSHOP PRACTICE 1 (x 1½) -DESCRIPTION- Purpose This module is designed to introduce a student following a career in carpentry and joinery and receiving complementary industrial training to the knowledge and skills required for everyday use of handtools in the workshop. Preferred No formal entry requirements Entry Level Learning The student should: Outcomes 1. know the practical applications of a range of woodworking tools and equipment; 2. know the practical applications of a range of timber joints; 3. know the use of a range of ironmongery/hardware; 4. demonstrate tool skills in the manufacture of timber joints and components. Content/ Safety regulations and safe working practices and Context procedures should be observed at all times. The following should be read in conjunction with objectives set out in the New Training Initiative recommendations for Carpenters and Joiners. Continuation of Module No. 85301 Session 1988-89 Corresponding to the Learning Outcomes 1-4: 1. Range of woodworking tools: (a) saws: rip saw; cross cut saw; panel saw; tenon saw; dovetail saw; compass saw; pad saw; bow saw; coping saw. (b) planes: smoothing plane; jack plane; try plane; block plane; bullnose plane; shoulder plane; rebate plane; bench rebate plane; side rebate plane; plough plane; compass plane; universal multi-plane; router; spokeshave.
[Show full text]
2014/15 Product Catalog
2014/15 PRODUCT CATALOG Prices Effective August 1, 2014 Supersedes all previously dated price lists. No. 17 Prices subject to change without notice. Affinity Tool Works, LLC • 1161 Rankin • Troy, Michigan 48083 Ph(248) 588-0395 • Fax(248) 588-0623 • [email protected] • www.affinitytool.com Pkg www.boratool.com Stock No. Description Part No. List Price Qty BORA Clamps & Vises 540445 4.5" Micro Bar Clamp (2-Pack) 6 $ 10.91 540603 Pistol Grip Set included 3 each of 6" and 12" 1 $ 81.82 540606-S 6" Midi Pistol Grip Clamp 6 $ 12.64 540606 6" Midi Pistol Grip Clamp (2-Pack) 6 $ 23.64 540612-S 12" Midi Pistol Grip Clamp 6 $ 15.45 540612 12" Midi Pistol Grip Clamp (2-Pack) 6 $ 30.00 540806 6" Pistol Grip Bar Clamp 6 $ 19.09 540812 12" Pistol Grip Bar Clamp 6 $ 20.91 540818 18" Pistol Grip Bar Clamp 6 $ 28.18 540824 24" Pistol Grip Bar Clamp 6 $ 30.00 540836 36" Pistol Grip Bar Clamp 6 $ 35.00 540170 7 Piece Clamp Set: 6" Midi Clamp (2), 12" Midi Clamp (2), 18" Bar Clamp, 24" Bar Clamp, 36" Bar Clamp 1 $ 140.00 550602 Clamp Plate 6 $ 12.73 550601 Clamp Extenders 6 $ 10.00 BORA Specialized Clamps & Vises 540520 20 Piece Mini Spring Clamp Set 1 $ 10.00 551025 Corner Clamp 6 $ 30.00 551027 Large Vise 6 $ 30.00 BORA Clamp Edge 540924 24" Clamp Edge 6 $ 36.36 540936 36" Clamp Edge 6 $ 41.82 540950 50" Clamp Edge 6 $ 47.27 540903 3 Piece Clamp Edge Set: 24", 36" & 50" 6 $ 121.82 540902 2 Pc Bora Clamp Set 6 $ 76.36 540024 24 Piece Displayer 1 $ 80.00 BORA Clamp Edge Wide Track & Accessories 541024 24" Clamp Edge Wide Track 6 $ 44.55 541042 42" Clamp Edge Wide Track 6 $ 56.36 541050 50" Clamp Edge Wide Track 6 $ 65.45 541066 66" Clamp Edge Wide Track 6 $ 80.00 541100 100" Clamp Edge Wide Track 6 $ 130.91 541000 24 Piece Wide Track Displayer 1 $ 83.00 542003 Wide Track Router Guide Plate 6 $ 23.64 542002 Wide Track Auxiliary Clamp, pair 6 $ 16.82 Page 2 © 2014 Affinity Tool Works, LLC Pkg Stock No.
[Show full text]
Tool Identification Guide
Subject: ______________________ Name: _______________________ Section: ____ Period: ____ Date: __________________, 201__ TOOL IDENTIFICATION GUIDE Production: Jenny Liang 2015, Kivanc Yildiz 2010 Drawings: Ruby Qu, Ann Ke, Judy Liu & Karina Wu 2013 Chantal Lo 2010, Isadora Kostic 2012 First published 2010 Revised & Expanded 2012, 2015 Electronics & Robotics Sir Winston Churchill Secondary Vancouver, British Columbia, Canada 06.16.2015 Why and How A knowledge of tool and instrument names will enhance your success in electronics and improve your life. Although tool identification quizzes were standard fifty years ago in all technical studies subjects, today they have been largely abandoned. Mastering this information is fun and fulfilling. In a secondary school such as ours, where the large majority speak English as a second language, this unit is especially valuable. Our guide groups tools by use: bending, clamping, cutting… The drawings appear alphabetically since students report that this approach aids memorization. A practice quiz booklet accompanies the guide. Names are replaced by blank lines. Students prepare for the quiz by testing themselves. During the actual quiz the tools and instruments are held aloft and shown randomly. Simultaneously, the teacher records the answer on an overhead projector transparency. Students mark each others quiz. Background This booklet first appeared in 2010 and underwent extensive revision and expansion in 2015. Six student artists generously contributed drawings. Thirty-nine drawings by Ruby Qu are included. Chantal Lo made a substantial contribution. Ann Ke, Judy Liu and Karina Wu also contributed. A separate electronic file of Ruby Qu’s full size drawings in 8.5 inch by 11 inch format is available at www.swcelectronics.com.
[Show full text]
Learner Guide
Hand & power tools Supporting: LMFFM2001B: Use furniture making sector hand and power tools Learner guide Developed in 2013-2014 for the WELL Program Hand and power tools Learner guide This unit is also available in an e-learning format, which contains additional photos, interactive exercises and a voice-over narration of the text. It can be viewed on CD- ROM, or live on the web at: www.kbcabinetmaking.com.au Developed by Workspace Training for the 2013-2014 Workplace English Language and Literacy (WELL) Program Kitchen and Bathroom Cabinetmaking resource development project © Commonwealth of Australia 2014 © Commonwealth of Australia 2014 Copyright and disclaimer ISBN: 978-1-925087-07-9 Funded under the Workplace English Language and Literacy Program by the Australian Government through the Department of Industry. © Commonwealth of Australia. 2014 CC BY-NC-SA This work is copyright. Except where otherwise indicated, and save for the Commonwealth Coat of Arms, the Department has applied the Creative Commons Attribution-Noncommercial-Share Alike 3.0 Australia Licence to this work. The Department of Industry must be attributed as the author of the Department’s copyright material. As far as practicable, material for which the copyright is owned by a third party has been clearly labelled. The Department has made all reasonable efforts to ensure that this material has been reproduced in the print-based resources and accompanying website with the full consent of the copyright owners. Requests and enquiries concerning the Department’s copyright material should be emailed to: [email protected] Questions about the design and content of the resource itself should be addressed to the project manager: David McElvenny Workspace Training PO Box 1954 Strawberry Hills, NSW, 2012 Email: [email protected] Disclaimer The content of this Learner guide is provided for educational purposes only.
[Show full text]
Oct 2010News.Pub
Guild of Oregon Woodworkers Volume #27, Issue #10 October 2010 OREGON WOOD WORKS W HAT’ S IN YOUR SHOP TODAY BOB OSWALD, PRESIDENT t’s been a long dry summer, and I all projects we do, once don’t mean the weather. The shop we look beyond the un- has been too idle. The exciting part desirable things that did- is that each time I enter it these n’t go quite according to Idays I’m getting more excited to get back plan, there’s a great to work on some furniture projects. pride in having joined a number of pieces of There’s this sofa table started months wood, using many tech- ago. It’s waiting for a steam bend on the niques, into something front apron, an upcoming newsletter arti- functional and attractive. cle I suspect. That said, we’re approaching that Tool of the Month This summer saw a back to hammer- time of year in the Guild, election of offi- and-nails project, a storage building for cers. I’m happy to be able to say that a Inside this Issue: lawn tools, etc. We’ve not been able to number of new faces are taking an active agree on its location in the yard for years, role in the Guild. It’s only hollow words Prez: In Your Shop 1 relegating my truck to often be parked unless you experience them, that we are outside while the lawnmower stayed each better in many ways for involve- In the Beginning 2 warm and dry. The new location blends ment.
[Show full text]
Robert Larson Company 
Robert Larson Company 1 Chisel Sets Bevel Edge Chisels Boxed Chisel Sets Wooden Handles Two different sets of high quality Two Cherries bevel edge chisels with These chisels are made of the highest quality German steel. Carefully made, pol- hardwood handles. The set of six ished all-around. One of the finest tools made in the world! Ten to fourteen inches chisels consists of sizes 6-10-12-16- in overall length. Choose between a traditional and well proportioned wooden Set of four and a set of six wooden 20-26mm, the set of four consists of handle, or nearly unbreakable cellulose acetate plastic handle. A number of sets are handled bevel edge chisels in a fitted 10-16-20-26mm. available which include the most important sizes. Inch sizing is approximate. wooden box. Keeps your chisels pro- tected in storage and ready to use. Set 500-1562 ..................................... Set of Six 500-1564 ...................................Set of Four Carefully forged blades are skillfully heat treated in an immersion bath method of six contains 6-10-12-16-20-26mm to achieve a Rockwell hardness of 61o C. This means that sharpening the chisels chisels. Set of four contains 10-16-20- may take a few extra minutes, but they will hold an edge significantly longer than 26mm chisels. almost any other chisels! After heat treating, the blades are polished to a rich finish 500-1559 .........Set of Four in Wooden Box 500-1561 ...........Set of Six in Wooden Box that makes them a joy to use. Fitting appropriate handles is the final step in produc- Chisel Sets ing these highest quality German chisels.
[Show full text]
Tool Identification Quiz
Subject: ______________________ Name: _______________________ Section: ____ Period: ____ Date: __________________, 201__ TOOL IDENTIFICATION QUIZ Production: Jenny Liang 2015, Kivanc Yildiz 2010 Drawings: Ruby Qu, Ann Ke, Judy Liu & Karina Wu 2013 Chantal Lo 2010, Isadora Kostic 2012 First published 2010 Revised & Expanded 2012, 2015 Electronics & Robotics Sir Winston Churchill Secondary Vancouver, British Columbia, Canada 06.16.2015 Why and How A knowledge of tool and instrument names will enhance your success in electronics and improve your life. Although tool identification quizzes were standard fifty years ago in all technical studies subjects, today they have been largely abandoned. Mastering this information is fun and fulfilling. In a secondary school such as ours, where the large majority speak English as a second language, this unit is especially valuable. Our guide groups tools by use: bending, clamping, cutting… The drawings appear alphabetically since students report that this approach aids memorization. A practice quiz booklet accompanies the guide. Names are replaced by blank lines. Students prepare for the quiz by testing themselves. During the actual quiz the tools and instruments are held aloft and shown randomly. Simultaneously, the teacher records the answer on an overhead projector transparency. Students mark each others quiz. Background This booklet first appeared in 2010 and underwent extensive revision and expansion in 2015. Six student artists generously contributed drawings. Thirty-nine drawings by Ruby Qu are included. Chantal Lo made a substantial contribution. Ann Ke, Judy Liu and Karina Wu also contributed. A separate electronic file of Ruby Qu’s full size drawings in 8.5 inch by 11 inch format is available at www.swcelectronics.com.
[Show full text]