Hazardous Areas Adjustable Pressure Switch 6905DZE* - Diaphragm Sensor

Hazardous Areas Adjustable Pressure Switch 6905DZE* - Diaphragm Sensor DESCRIPTION SERIES: • HighlyH reliable devices utilizing the 6905DZE*-7042 CCCS Dual-Snap® Belleville disc spring pprinciple pioneered by CCS’ engineers. ADJUSTABLE SET POINT RANGE: • EEngineering based on aerospace ttechnology. DIFFERENTIAL PRESSURE: • RRigid, compact and internally adjustable .5 to 75 PSID fofor convenient fi eld set point adjustment. 0.03 to 5.17 bar 3.45 to 517 kPa • RRepeatable and stable set points. • VVibration and shock resistant. OPERATING TEMPERATURE: • HHigh cycle life. Temperature limits change with O-ring selection. • HHigh over-pressure capability. -40° to 186°F ((System and Proof) -40° to 86°C • CCertifi ed explosion proof hermetically ssealed electrical assembly for STANDARD FEATURES: • ATEX - Baseefa Certifi ed eenvironmental protection. • CE Mark • VVarious options for electrical ratings to • CCC mmeet a wide range of application • NEMA: 4, 7, 9,13 / IP66 & 67 rrequirements and media compatibility. • NACE MR0175 / ISO 15156 • Hermetically Sealed Electrical Assembly SSHIPPING WEIGHT: APPROXIMATELY 49 OUNCES • 316 SST Electrical Assembly ((1389 GRAMS) • 300 Series SST Housing • M20 Electrical Connection INSTALLATION DRAWING DESIGN PRINCIPLES FIELD SETTING: Loosen access cover. Adjust adjustment screw using screwdriver slot as illustrated, then attach to a variable pressure source with a suitable gage, and check that the circuit continuity operates at the pressures desired. Clockwise to increase settings. Counterclockwise to decrease setting. NOTE: DO NOT USE ELECTRICAL HEX FOR TORQUING. Models: 6905DZE*, Page 1 of 2 ccsdualsnap.com Form 830G, 12.10.13 Hazardous Areas Adjustable Pressure Switch 6905DZE* - Diaphragm Sensor OPERATING AND ORDERING DATA WETTED PARTS: 1/4"-18 NPT STAINLESS STEEL PRESSURE PORT, POLYIMIDE HOW TO ORDER DIAPHRAGM, VITON O-RING Follow these steps to build your part number: PROOF SERIES ADJUSTABLE SET POINT PRESSURE 1. Specify the series 6905DZE*-7042 RANGE PSID (BAR) APPROX. SYSTEM PSIG (BAR) based on your required DEAD PRESSURE set point, range, dead BAND HIGH OVER LOW PSIG (BAR) BOTH INCREASING DECREASING PSI (BAR) LOW OVER HIGH band, system pressure PORTS and proof pressure. PRESSURE PRESSURE SIMULT. HIGH LOW 2. Add desired options model code letter. 3. Add the applicable 1.5-18 0.5-17 1 standard suffi x number. 6905DZE*8-7042 (0.103-1.24) (0.03-1.17) (0.069) (Ex: 6905DZEM8-7043) 400 750 750 400 (28) (52) (52) (28) PRESSURE 6-75 2-71 4 CONVERSION 6905DZE*10-7042 (0.414-5.2) (0.14-4.9) (0.28) 1 BAR = 14.5 PSI 1 kPa = 0.145 PSI OPTIONAL STANDARD PRESSURE SWITCH CERTIFICATIONS MODIFIED SUFFIXES * ATEX - Certifi cate No. Baseefa 03ATEX0700X. Baseefa certifi ed equipment or 7043: Gold Contacts and protective system intended for potentially explosive atmospheres Directive 94/9/EC. Stainless Steel Body In compliance with EN60079-0:2012, EN 60079-1:2007, EN 60079-31:2009. (-7042) ELECTRICAL CHARACTERISTICS RATING OF SWITCH ELEMENT AMPERES VOLTS SPDT DPDT "M" Res. Res. OPTIONS MODEL 125 AC - 50/60 Hz 11 11 CODES 250 AC - 50/60 Hz 11 11 30 DC 55 M: DPDT Electrical 125 DC .5 .5 *125 AC - 50/60 Hz 1 max 1 max *30 DC 1 max 1 max CERTIFICATIONS *Gold Contacts -7043 Suffix Consult CCS website for complete certifi cation and SCHEMATIC AND WIRING CODE approval listing. Note: Additional modifi ed standard suffi xes are available, consult CCS sales department or CCS Representative. Models: 6905DZE*, Page 2 of 2 ccsdualsnap.com Form 830G, 12.10.13.

Copy Link

Recommended publications

+1. Introduction 2. Cyrillic Letter Rumanian Yn
MAIN.HTM 10/13/2006 06:42 PM +1. INTRODUCTION These are comments to "Additional Cyrillic Characters In Unicode: A Preliminary Proposal". I'm examining each section of that document, as well as adding some extra notes (marked "+" in titles). Below I use standard Russian Cyrillic characters; please be sure that you have appropriate fonts installed. If everything is OK, the following two lines must look similarly (encoding CP-1251): (sample Cyrillic letters) АабВЕеЗКкМНОопРрСсТуХхЧЬ (Latin letters and digits) Aa6BEe3KkMHOonPpCcTyXx4b 2. CYRILLIC LETTER RUMANIAN YN In the late Cyrillic semi-uncial Rumanian/Moldavian editions, the shape of YN was very similar to inverted PSI, see the following sample from the Ноул Тестамент (New Testament) of 1818, Neamt/Нямец, folio 542 v.: file:///Users/everson/Documents/Eudora%20Folder/Attachments%20Folder/Addons/MAIN.HTM Page 1 of 28 MAIN.HTM 10/13/2006 06:42 PM Here you can see YN and PSI in both upper- and lowercase forms. Note that the upper part of YN is not a sharp arrowhead, but something horizontally cut even with kind of serif (in the uppercase form). Thus, the shape of the letter in modern-style fonts (like Times or Arial) may look somewhat similar to Cyrillic "Л"/"л" with the central vertical stem looking like in lowercase "ф" drawn from the middle of upper horizontal line downwards, with regular serif at the bottom (horizontal, not slanted): Compare also with the proposed shape of PSI (Section 36). 3. CYRILLIC LETTER IOTIFIED A file:///Users/everson/Documents/Eudora%20Folder/Attachments%20Folder/Addons/MAIN.HTM Page 2 of 28 MAIN.HTM 10/13/2006 06:42 PM I support the idea that "IA" must be separated from "Я".
[Show full text]
An Exploratory Study on Functionally Graded Materials with Applications to Multilayered Pavement Design
An Exploratory Study on Functionally Graded Materials with Applications to Multilayered Pavement Design Ernie Pan, Wael Alkasawneh, and Ewan Chen Prepared in cooperation with The Ohio Department of Transportation and the U.S. Department of Transportation, Federal Highway Administration State Job Number 134256 August 2007 1. Report No. 2. Government Accession No. 3. Recipient’s Catalog No. FHWA/OH-2007/12 4. Title and subtitle 5. Report Date An Exploratory Study on Functionally Graded Materials with August 2007 Applications to Multilayered Pavement Design 6. Performing Organization Code 7. Author(s) 8. Performing Organization Report No. Ernie Pan, Wael Alkasawneh, Ewan Chen 10. Work Unit No. (TRAIS) 9. Performing Organization Name and Address 11. Contract or Grant No. 134256 Department of Civil Engineering The University of Akron 13. Type of Report and Period Akron, OH 44325-3905 Covered Final Report 12. Sponsoring Agency Name and Address 14. Sponsoring Agency Code Ohio Department of Transportation 1980 West Broad Street Columbus, OH 43223 15. Supplementary Notes 16. Abstract The response of flexible pavement is largely influenced by the resilient modulus of the pavement profile. Different methods/approaches have been adopted in order to estimate or measure the resilient modulus of each layer assuming an average modulus within the layer. In order to account for the variation in the modulus of elasticity with depth within a layer in elastic pavement analysis, which is due to temperature or moisture variation with depth, the layer should be divided into several sublayers and the modulus should be gradually varied between the layers. A powerful and innovative computer program has been developed for elastic pavement analysis that overcomes the limitations of the existing pavement analysis programs.
[Show full text]
Historic Mine Opening Closure Methodology, Specifications, and Details – Utah and Colorado Bureau of Land Management Districts
Historic Mine Opening Closure Methodology, Specifications, and Details – Utah and Colorado Bureau of Land Management Districts Prepared for Freeport Minerals Corporation December 2017 9191 South Jamaica Street Englewood, CO 80112 Contents Section Page Acronyms and Abbreviations ............................................................................................................. iv Document Overview ......................................................................................................................... 1 Introduction ...................................................................................................................................... 2 Solid PUF Plug with or without Bat Gate ............................................................................................ 3 3.1 Preparation ......................................................................................................................... 3 3.2 Closure Steps ...................................................................................................................... 3 3.3 Material Specifications and Installation ............................................................................. 7 Wire Rope Netting ............................................................................................................................ 8 4.1 Closure Steps ...................................................................................................................... 8 4.2 Material Specifications ......................................................................................................
[Show full text]
PSI CHI JOURNAL of PSYCHOLOGICAL RESEARCH Psi Chi Is the International Honor SoCiety in Psychology, FoundEd in 1929
Psi Chi Psychological Journal of Research SUMMER 2018 | VOLUME 23 | ISSUE 3 ISSN: 2325-7342 Published by Psi Chi, The International Honor Society in Psychology ® ® ® ABOUT PSI CHI PSI CHI JOURNAL OF PSYCHOLOGICAL RESEARCH Psi Chi is the International Honor So ciety in Psychology, found ed in 1929. Its mission: "recognizing and promoting excellence in the science and application of psy chol ogy." Mem SUMMER | VOLUME 23, ISSUE 3 ber ship is open to undergraduates, graduate students, faculty, and alumni mak ing the study of psy chol ogy one of their major interests and who meet Psi Chi’s min i mum qual i fi ca tions. EDITOR Psi Chi is a member of the Asso cia tion of Col lege Honor Soci et ies (ACHS), and is an affiliate DEBI BRANNAN, PhD of the Ameri can Psy cho logi cal As so cia tion (APA) and the Association for Psy cho log i cal Western Oregon University Science (APS). Psi Chi’s sister honor society is Psi Beta, the national honor society in Telephone: (503) 751-4200 psychology for com mu nity and junior colleges. E-mail: [email protected] Psi Chi functions as a federation of chap ters located at over 1,150 senior col leg es and universities around the world. The Psi Chi Central Office is lo cat ed in Chatta nooga, ASSOCIATE EDITORS Ten nessee. A Board of Directors, com posed of psy chol o gy faculty who are Psi Chi members MARY BETH AHLUM, PhD and who are elect ed by the chapters, guides the affairs of the Or ga ni za tion and sets pol i cy Nebraska Wesleyan University with the ap prov al of the chap ters.
[Show full text]
5892 Cisco Category: Standards Track August 2010 ISSN: 2070-1721
Internet Engineering Task Force (IETF) P. Faltstrom, Ed. Request for Comments: 5892 Cisco Category: Standards Track August 2010 ISSN: 2070-1721 The Unicode Code Points and Internationalized Domain Names for Applications (IDNA) Abstract This document specifies rules for deciding whether a code point, considered in isolation or in context, is a candidate for inclusion in an Internationalized Domain Name (IDN). It is part of the specification of Internationalizing Domain Names in Applications 2008 (IDNA2008). Status of This Memo This is an Internet Standards Track document. This document is a product of the Internet Engineering Task Force (IETF). It represents the consensus of the IETF community. It has received public review and has been approved for publication by the Internet Engineering Steering Group (IESG). Further information on Internet Standards is available in Section 2 of RFC 5741. Information about the current status of this document, any errata, and how to provide feedback on it may be obtained at http://www.rfc-editor.org/info/rfc5892. Copyright Notice Copyright (c) 2010 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.
[Show full text]
Orion 3A Manual
Orion-3A Pneumatic Pressure Controller Part #55287, Patent No. 4.698.998 SPECIAL FEATURES: • Orion 3A is a variable volume pressure controller with on operating pressure from vacuum to 10,000 psi. It consists of two low torque, fine micro-metering valves with positive shut-off, adjustable stop and soft seat. The pressure valve controls the inlet pressure and the other valve vents to atmosphere. • The vernier is located at the center of the controller and allows the operator a very fine pressure adjustment (approx. ±5% point max.) without using the pressure or vent valve. • Selecting the appropriate O-ring material may extend the wide range of gas applications. • There is one inlet, one outlet, and two test ports. One test port may be used to connect a pressure transducer or pressure gage standard; the other test port may be used to connect the unit under test. OPERATION: The pressure valve will begin to open when it is turned counter clockwise approximately 15 degrees. Full open position of the valves is achieved with a maximum of 3 1/2 turns from the closed position. Use the pressure/vent valves to achieve ±95% of the target pressure. The pressure and vent valves must be closed before operating the vernier. The vernier is a piston and cylinder configuration, which generates ±5% pressure, or vacuum of the indicated pressure. The vernier has a fine adjustment sensitivity of .005 psi. Very low torque is required to turn the vernier... FINGERTIP ADJUSTMENT EVEN AT 10,000 psi!!!!! SPECIFICATIONS: • Pressure Range: 0-10,000 psi and Vacuum • Proof Pressure: 15,000 psi Precision Precision Pneumatic Controller • Pressure & Vent Valve Orifice: .032 • CV: .007 • Mechanical Rotation: 3 1/2 turns (nom.) • Torque: Fingertip adjust (even at 10,000 psi) • Vernier Volume: .4 cubic inch (nom.) • Mechanical Rotation: 15 turns (nom.) • Adjustable sensitivity: .005 psi • Construction: 300 Series stainless steel body, aluminum knobs, black anodize.
[Show full text]
52044 Pinelawn Lawn Crypts Augst
ANDREW M. CUOMO DIVISION OF CEMETERIES GOVERNOR STATE OF NEW YORK DEPARTMENT OF STATE CEMETERY BOARD 123 W ILLIAM S TREET R OSANNA R OSADO NEW YORK, NY 10038 SECRETARY OF STATE CHAIR TELEPHONE: (212) 417-5713 FAX: (212) 417-2322 LETITIA JAMES WWW.DOS.NY.GOV ATTORNEY GENERAL DR. HOWARD A. ZUCKER COMMISSIONER OF HEALTH TO: NEW YORK STATE CEMETERY BOARD FROM: LEWIS A. POLISHOOK, Director CC: ANTONIO MILILLO, Counsel DATE: JULY 22, 2020 RE: PINELAWN MEMORIAL PARK, NO. 52-044 INSTALLATION OF LAWN CRYPTS By application dated July 8, 2020, Pinelawn Memorial Park (the Cemetery) seeks confirmation that the New York State Cemetery Board does not object to its application to develop additional lawn crypts adjacent to a section of lawn crypts approved by the New York State Cemetery Board on December 11, 2018. The Cemetery is the largest regulated cemetery in New York. It consists of 786 acres spanning Wellwood Avenue, and is located in the Town of Babylon, in Suffolk County. It has a series of mausoleum buildings, but is primarily a memorial park, although it also has lawn crypt sections and sections with upright markers. The cemetery appears to be in compliance with all Division regulations; the cemetery is consistently well-maintained and generates few lot owner complaints. The Cemetery maintains a conflict of interest policy. No related parties are involved in this transaction. An excerpt from the Cemetery’s most recent 990 showing compensation is included as an exhibit. Summary of Recommendation The Division recommends approval of the project. The cemetery has a demonstrated track record of selling such burial spaces profitably, and has built them before, so it is familiar with the additional engineering requirements of lawn crypts.
[Show full text]
Presentazione Standard Di Powerpoint
Linear Accelerators David Alesini (INFN-LNF, Frascati, Rome, Italy) ACKNOWLEDGEMENTS Several pictures, schemes, images and plots have been taken from papers and previous presentations of the following authors that I would like to thank. I would like to acknowledge in particular the following authors: A. Gallo, E. Jensen, A. Lombardi, F. Tecker and M. Vretenar I would like also to acknowledge the following authors: Hans Weise, Sergey Belomestnykh, Dinh Nguyen, John Lewellen, Leanne Duffy, Gianluigi Ciovati, Jean Delayen, S. Di Mitri, R. Carter, G. Bisoffi, B. Aune, J. Sekutowicz, H. Safa, D. Proch, H. Padamsee, R. Parodi, Paolo Michelato, Terry Garvey, Yujong Kim, S. Saitiniyazi, M. Mayierjiang, M. Titberidze, T. Andrews, C. Eckman, Roger M. Jones, T. Inagaki, T. Shintake, F. Löhl, J. Alex, H. Blumer, M. Bopp, H. Braun, A. Citterio, U. Ellenberger, H. Fitze, H. Joehri, T. Kleeb, L. Paly, J.Y. Raguin, L. Schulz, R. Zennaro, C. Zumbach. Detlef Reschke, David Dowell, K. Smolenski, I. Bazarov, B. Dunham, H. Li, Y. Li, X. Liu, D. Ouzounov, C. Sinclair 104 LINACs operating LINAC APPLICATIONS around the world Free Electron Lasers Injectors for synchrotrons Spallation sources for Nuclear waste treatment neutron production and controlled fission for Medical applications: energy production (ADS) radiotherapy Industrial applications Material testing for fusion nuclear reactors National security Material Ion Material/food treatment implantation sterilization LINAC: BASIC DEFINITION AND MAIN COMPONENTS LINAC (linear accelerator) is a system that allows
[Show full text]
Cracking of the PCC Layer in Composite Pavement
Cracking of the PCC Layer in Composite Pavement A DISSERTATION SUBMITTED TO THE FACULTY OF THE GRADUATE SCHOOL OF THE UNIVERSITY OF MINNESOTA BY PRIYAM SAXENA IN PARTIAL FULFILLMENT OF THE REQUIREMENTS FOR THE DEGREE OF DOCTOR OF PHILOSOPHY Lev Khazanovich, Advisor December 2011 © Priyam Saxena 2011 ACKNOWLEDGEMENTS I wish to express my sincere thanks to my advisor Dr. Lev Khazanovich for the guidance, cooperation, and continuous support that he provided during my stay at the University of Minnesota. I greatly appreciate his patience and the encouragement he provided to help me focus on the work. I would also like to thank my thesis committee members Dr. Mihai Marasteanu, Dr. Henryk K. Stolarski, and Dr. Douglas M. Hawkins for their help and valuable feedback on this dissertation. The financial support provided by the Minnesota Department of Transportation and the Federal Highway Administration (FHWA) Transportation Pooled Fund Study TPF-5(149) ―Design and Construction Guidelines for Thermally Insulated Concrete Pavements‖ is deeply acknowledged. Special thanks to all my fellow students for making memories that I will cherish forever. Last but not the least, I am most grateful to my husband, Amit for his love and support during this time. I am forever thankful to my loving family. i To my parents ii ABSTRACT An asphalt concrete (AC) overlay of a jointed plain concrete pavement (JPCP) is intended to extend the service life of the existing pavement structure. Also known as composite pavements, such pavements exhibit features of both rigid and flexible pavements. While behavior of rigid pavements is mainly elastic, behavior of asphalt layer is load-duration dependent.
[Show full text]
204.02 204-1 Section
204.02 1 SECTION 204 - EXCAVATION AND BACKFILL 2 FOR MISCELLANEOUS FACILITIES 3 4 5 204.01 Description. This section describes the following: 6 7 (A) Excavating and backfilling to depths and lines established for 8 foundations of roadway and sign lighting standards, and traffic signal 9 standards. 10 11 (B) Excavating and backfilling trenches for utilities pipes (including water, 12 sewer, telephone, oil, and gas lines) and conduits (including roadway and 13 sign lighting, traffic signal, and other communications systems). 14 15 (C) Excavating and backfilling for water and sewer manholes and 16 appurtenances. 17 18 (D) Disposing of surplus material from excavations. 19 20 Excavating and backfilling for water and sewer pipes, manholes, and 21 appurtenances are described further in Section 624 – Water System and Section 22 625 – Sewer System. 23 . 24 204.02 Materials. 25 26 Structure Backfill Material 703.20 27 28 Trench Backfill Material 703.21 29 30 Geotextiles for Underdrain Applications 716.03 31 32 Cullet and Cullet-Made Materials 717 33 34 Structure and trench backfill material shall include mixture of aggregate and 35 cullet. When cullet is not produced on the project island, or material unit price of 36 cullet is greater than material unit price of structure backfill or greater than material 37 unit price of trench backfill, cullet may be excluded for that backfill application. 38 Before excluding cullet, submit availability and pricing documentation. 39 40 Trench gravel backfill material shall conform to AASHTO M 43, size number 41 67. When tested in accordance with AASHTO T 96, the LA abrasion shall not 42 exceed 40 percent at 500 revolutions.
[Show full text]
1 Symbols (2286)
1 Symbols (2286) USV Symbol Macro(s) Description 0009 \textHT <control> 000A \textLF <control> 000D \textCR <control> 0022 ” \textquotedbl QUOTATION MARK 0023 # \texthash NUMBER SIGN \textnumbersign 0024 $ \textdollar DOLLAR SIGN 0025 % \textpercent PERCENT SIGN 0026 & \textampersand AMPERSAND 0027 ’ \textquotesingle APOSTROPHE 0028 ( \textparenleft LEFT PARENTHESIS 0029 ) \textparenright RIGHT PARENTHESIS 002A * \textasteriskcentered ASTERISK 002B + \textMVPlus PLUS SIGN 002C , \textMVComma COMMA 002D - \textMVMinus HYPHEN-MINUS 002E . \textMVPeriod FULL STOP 002F / \textMVDivision SOLIDUS 0030 0 \textMVZero DIGIT ZERO 0031 1 \textMVOne DIGIT ONE 0032 2 \textMVTwo DIGIT TWO 0033 3 \textMVThree DIGIT THREE 0034 4 \textMVFour DIGIT FOUR 0035 5 \textMVFive DIGIT FIVE 0036 6 \textMVSix DIGIT SIX 0037 7 \textMVSeven DIGIT SEVEN 0038 8 \textMVEight DIGIT EIGHT 0039 9 \textMVNine DIGIT NINE 003C < \textless LESS-THAN SIGN 003D = \textequals EQUALS SIGN 003E > \textgreater GREATER-THAN SIGN 0040 @ \textMVAt COMMERCIAL AT 005C \ \textbackslash REVERSE SOLIDUS 005E ^ \textasciicircum CIRCUMFLEX ACCENT 005F _ \textunderscore LOW LINE 0060 ‘ \textasciigrave GRAVE ACCENT 0067 g \textg LATIN SMALL LETTER G 007B { \textbraceleft LEFT CURLY BRACKET 007C | \textbar VERTICAL LINE 007D } \textbraceright RIGHT CURLY BRACKET 007E ~ \textasciitilde TILDE 00A0 \nobreakspace NO-BREAK SPACE 00A1 ¡ \textexclamdown INVERTED EXCLAMATION MARK 00A2 ¢ \textcent CENT SIGN 00A3 £ \textsterling POUND SIGN 00A4 ¤ \textcurrency CURRENCY SIGN 00A5 ¥ \textyen YEN SIGN 00A6
[Show full text]
Measurement of the CP-Violating Phase Phis in the Bs -> J/Psi Phi
Physics Letters B 816 (2021) 136188 Contents lists available at ScienceDirect Physics Letters B www.elsevier.com/locate/physletb Measurement of the CP-violating phase φs in the 0 → → + − + − Bs √ J/ψ φ(1020) μ μ K K channel in proton-proton collisions at s = 13 TeV .The CMS Collaboration CERN, Switzerland a r t i c l e i n f o a b s t r a c t Article history: 0 The CP-violating weak phase φs and the decay width difference s between the light and heavy Bs Received 5 July 2020 mass eigenstates are measured with the CMS detector at the LHC in a sample of 48 500 reconstructed Received in revised form 24 February 2021 0 → → + − + − Bs J/ψφ(1020) μ μ K K events. The measurement is based on a data sample√ corresponding Accepted 26 February 2021 −1 to an integrated luminosity of 96.4fb , collected in proton-proton collisions at s = 13 TeV in Available online 3 March 2021 2017–2018. To extract the values of φs and s, a time-dependent and flavor-tagged angular analysis Editor: M. Doser + − + − of the μ μ K K final state is performed. The analysis employs a dedicated tagging trigger and a Keywords: novel opposite-side muon flavor tagger based on machine learning techniques. The measurement yields =− ± ± = ± ± −1 CMS φs 11 50 (stat) 10 (syst) mrad and s 0.114 0.014 (stat) 0.007 (syst) ps , in agreement√ with Physics the standard model predictions. When combined with the previous CMS measurement at s = 8 TeV, Oscillations the following values are obtained: φs =−21 ± 44 (stat) ± 10 (syst) mrad, s = 0.1032 ± 0.0095 (stat) ± B physics −1 0.0048 (syst) ps , a significant improvement over the 8TeVresult.
[Show full text]