DOCSLIB.ORG

Hydraulic Machinery and Cavitation Volume I

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Hydraulic Machinery and Cavitation Volume I HYDRAULIC MACHINERY AND CAVITATION VOLUME I HYDRAULIC MACHINERY AND CAVITATION Proceedings of the XVIII JAHR Symposium on Hydraulic Machinery and Cavitation WIRe r-v rv .AJRH VOLUMEI Edited by E. CABRERA, V. ESPERT and F. MARTfNEZ Polytechnic University of Valencia, Spain Polytechnic Universi1y of Valencia Hydraulic and Environmental Eng. Dept. FLUID MECHANICS GROUP Co-sponsors: I :11-1 111- ][ --.-----·~-~- REE Centro dlnWol y uperintet~t.:IOn..... ••••pUbfic .. II RED ELECTRICA IBERDROLA Springer-Science+Business Media, B.V. A C.I.P. Catalogue record for this book is available from the Library of Congress. ISBN 978-94-010-9387-3 ISBN 978-94-010-9385-9 (eBook) DOI 10.1007/978-94-010-9385-9 Printedon acid-free paper All Rights Reserved © 1996 bySpringer Science+Business Media Dordrecht Originally published by Kluwer Academic Publishers in 1996 No part of the material protected by this copyright notice may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying, recording or by any information storage and retrieval system, without written permission from the copyright owner. TABLE OF CONTENTS Acknowledgements XVll Preface xix Foreword xxi VOLUME I INVITED LECTURES The hydroelectricity in the world-Present and future. Brekke, H. 3 Analysis of transients caused by hydraulic machinery. Chaudhry, M.H. 17 Some present trends in hydraulic machinery research. Fanelli, M. 23 Rapid prototyping of hydraulic machinery. Schilling R., Riede[, N., Bader, R., Ascherbrenner, T., Weber, Ch., Fernandez, A. 40 Fluid transients in flexible piping systems. A perspective on recent developments Wiggert, D.C. 58 SYMPOSIUM CONTRffiUTIONS GROUP 1 HYDRAULIC TURBINES. ANALYSIS AND DESIGN 1. 1 NUMERICAL ANALYSIS OF COMPONENTS A decision aid system for hydraulic power station refurbishment procedure. Bellet, L., Parkinson, E. Avellan, F., Cousot, T., Laperrousaz, E. 71 A three dimensional spiral casing Navier-Stokes flow simulation. Bruttin, C.H., Kueny, J.L., Boyer, B., Heon, K,. Vu, T.C. and Parkinson, E. 81 Tip clearance flow in turbomachines- experimental flow analysis. Ciocan, G.D. and Kueny, J.L. 91 vi Numerical prediction of hydraulic Iosses in the spiral casing of a Francis turbine. Drtina, P. and Sebestyen, A. 101 Improvements of a graphical method for calculation of flow on a Pelton bucket. Hana, M. 111 Flow behavior and performance of draft tubes for bulb turbines. Kanemoto, T.,Uno, M., Nemoto, M., and Kashiwabara, T. 120 Performance analysis of draft tube for GAMM francis turbine. Kubota, T., Han, F., and Avellan, F. 130 ModeHing complex draft-tube flows using near-wall turbulence closures. Ventikos, Y., Sotiropoulos, F. and Patel, V.C. 140 1.2 NUMERICAL ANALYSIS AND DESIGN OF HYDRAULIC MACillNERY Fluid flow interactions in hydraulic machinery. Aschenbrenner, T., Riedel, N. and Schilling, R. 150 Numerical optirnization of high head pump-turbines Buchmaicher, H,. Quaschnowitz, B., Moser, W. and Klemm, D. 160 Numerical hill chart prediction by means of CFD stage simulation for a complete Francis turbine. Keck, H. Drtina, P. and Siek, M. 170 Development of a new generation of high head pump-turbines, Guangzhou II. Klemm, D., Jaeger, E.U., and Hauff, C. 180 Development of integrated CAE tools for design assessment and analysis of hydraulic turbines. Masse, B,. Pastorel, H. and Magnan, R. 190 Design and analysis of a two stage pump turbine Mazzouji, F. , Francois, M. Hebrard, F., Houdeline, B. and Bazin, D. 200 Study of high speed and high head reversible pump-turbine Nakamura, T., Nishizawa, H., Yasuda, M., Suzuki, T. and Tanaka, H. 210 vii Analysis of the performance of a bulb turbine using 3-D viscous numerical techniques Qian, Y., Suzuki, R. and Arakawa, C. 220 Analysis of the inlet reverse flows in a pump turbine using 3-D viscous numerical techniques Qian, Y., Suzuki, R. and Arakawa, C. 230 Importance of interaction between turbine components in flow field simulation Riedelbauch, S,. Klemm, D. and Hauff, C. 238 From components to complete turbine numerical simulation Sabourin, M., Labrecque, Y. and de Henau, V. 248 Validation of a stage calculation in a Francis turbine Siek M., Casey, M. V. and Galpin, P.F. 257 Simulation of flow through Francis turbine by LES method Song, C.C.S., Xiangying, Ch., Ikohagi,T., Sato, 1., Shinmei, K. and Tani, K. 267 Simulation of flow through pump-turbine Song, C.C.S., Changsi, C., Ikohagi,T., Sato, 1., Shinmei, K. and Tani, K. 277 1.3 LOSS ANALYSIS AND SCALE EFFECTS The scale effect in Kaplan turbines. New relationships for the calculation of scalable and non-scalable hydraulic Iosses and of the coefficient V. Anton, I.M. 284 Analysis of Iosses in hydraulic turbines. Brekke, H. 294 Scaling-up head discharge characteristics from model to prototype. Couston, M. and Philibert, R. 304 Recent development of studies on scale effect !da, T., Kubota,T. , Kurokawa, 1. and Tanaka, H. 313 Prediction of scalable loss in Francis runners of different specific speed Kitahora, T., 1urokawa, 1., Matumoto, M. and Suzuki, R. 323 viii Scale effect of jet interference in multinozzle Pelton turbines Nakanishi, Y. and Kubota, T. 333 Further development of step-up formula considering surface roughness Nichtawitz, A. 342 Numerical simulations of jet in a Pelton turbine. Nonoshita, T. , Matsumoto, Y., Kubota,T. and Ohashi, H. 352 An assessment of the loss distribution in Francis turbines Suzuki, R., Qian, Y., Kitahora, T. and Kurokawa, J. 361 GROUP 2. HYDRAULIC PUMPS Unsteady flow calculation in a centrifugal pump using a finite element method. Bert, P.F., Combes, J.F. and Kueny, J.L. 371 Steady and unsteady flow pattem between stay and guide vanes in a pump-turbine Ciocan, G., Kueny, J. L. and Mesquita, A.L.A. 381 Self-sustained oscillation of gas-liquid flow in a centrifugal pump with semi-open impeller Kurokawa, J., Matsui, J., Takada, H. and Hirayama, T. 391 Measurements in the dynamic pressure fteld of the volute of a centrifugal pump Parrondo, J.L., Fernandez, J., Santolaria, C. and Gonzalez, J. 401 Functional modelling of pump volute geometry Thackray, P.R. and James, R.D. 411 Analysis of flow measurements in the impeller and vaned diffuser of a centrifugal pump operating at part Ioad. Toussaint, M. and Bureau, F. 419 Influence of the blade roughness on the hydraulic performance of a mixed-flow pump. A viscous analysis Undreiner, S. and Dueymes, E. 428 Improvement of performance of centrifugal pumps based on computational and theoretical methods and experimental design Vinokurov, A.F., Volkov, A.V., Morgunov, G.M. and Pankratov, S.N. 438 ix Liquid-particulate two-phase flow in centrifugal impeller by turbulent simulation Wu, Y., Dai, 1., Mei, Z., Oba, S. and lkoagi, T. 445 GROUP 3. HYDRAULIC ELEMENTS. DYNAMIC CHARACTERIZATION AND HYDRAULIC BEHAVIOUR. Application of the method of kinetic balance for flow passages forming. Benisek, M., Cantrak, S., lgnatovic, B. and Pokrajac, D. 455 Dynamics of large hydrogenerators. Brito, G.C., Weber, H.l. and Fuerst, A.G.A. 464 Instabilities in a flow-control valve. Cigada, A., Guadagnini, A. and Orsi, E. 474 Study of stayvane vibration by hydroelastic model. Deniau, J.L. 484 Study of dynamic behaviour of non-retum valves. Franrois, P. 494 Optimum hydraulic design of two-way inlet conduit of Wangyuhe pumping station Linguang, L., Jiren, Z. and Rentian, Z. 504 Flow analysis for the intake of low-head hydro power plants Ruprecht, A., Maihofer, M. and Gode, E. 514 GROUP 4. CAVITATION AND SAND EROSION Efficiency alteration of Francis turbines by travelling bubble cavitation. Arn, Ch., Dupont, Ph. and Avellan, F. 524 Cavitation erosion prediction on Francis turbines - Part 1. Measurements on the prototype. Bourdon, P., Pfarhat, M., Simoneau, R., Pereira, F., Dupont, P., Avellan, F. and Dorey, I.M. 534 Determination of critical cavitation Iimit in the pressure control devices. Castorani, A., De Martino, G. and Fratino, U. 544 X Stability of air cavities in tip vortices. Crespo, A., Castro, F., Manuel, F. and Fruman, D.H. 554 Cavitation erosion prediction on Francis turbines - Part 3 Methodologies of prediction. Dorey, J.M., Laperrousaz, E., Avellan, F., Dupont, P., Simoneau, R. and Bourdon, P. 564 Cavitation erosion prediction on Francis turbines - Part 2. Model test and flow analysis. Dupont, P.H., Caron, J.F., Avellan, F., Bourdon, P., Lavigne, M., Farhat, M., Simoneau, R., Dorey, J.M., Archer, A., Laperrousaz, E. and Couston, M. 574 Impact of vapour production and cavity dynamics on the estimation of thermal effects in cavitation. Fruman, D.H., Reboud, J.L. and Stutz, B. 584 Aireation versus cavitation in dam spillways: self-aeration and artificial aeration (aerators). Gutierrez , R. 594 Leading edge cavitation in a centrifugal pump: Numerical predictions compared with model tests Hirschi, R., Dupont, P.H., Avellan, F., Favre, J.N., Guelich, F., and Handloser, W. 604 The relation between erosion ripples on the wetted surface of hydraulic turbine and instability waves in the turbulent boundary layer Huang, S. and Cheng, L. 614 Acoustic method and its applications on measuring and judging cavitation of hydraulic turbine. Kehuang, L. and Chun, Y. 622 Numerical simulation for dilute sandy water flow in plane cascade Liu, X.B., Zeng, Q.C. and Zhang, L.D. 632 Review of research on abrasion and cavitation of silt-laden flows through hydraulic turbines in China Mei, Z. and Wu, Y. 641 Effect of the leading edge design on sheet cavitation araund a blade section Reboud, J.L., Rebattet, C. and More[, P. 651 xi VOLUME II GROUP 5. HYDRAULIC TRANSIENTS AND CONTROL SYSTEMS RELATED WITH HYDRAULIC MACIDNERY AND PLANTS Optimal closure of a valve for minimizing waterhammer. Abreu, J., Cabrera, E., Garcia-Serra, J. and L6pez, P.A. 661 Qualitative flow visualizations during fast start-up of centrifugal pumps. Barrand, J.P.
Load more

Recommended publications
  • 780 Solid Waste Maintenance Technician
    780 Solid Waste Maintenance Technician Nature of Work This is skilled mechanical and maintenance work performing a variety of activities associated with the repair and routine maintenance of a variety of solid waste trucks and machinery used for solid waste operations. Activities associated with the job include performing routine preventive maintenance, safety inspections and repair work on all trucks, machinery and equipment, changing and repairing large truck tires, and assisting with building maintenance and repair activities. Additional activities include diagnosing vehicle components and/or equipment malfunctions, performing minor body work and welding and fabricating parts when required, repairing hydraulic equipment located at convenience centers and assisting with transfer station and landfill operations when necessary. Job duties require considerable knowledge and experience in vehicle repair and maintenance, hydraulics, welding, air conditioning repair and metal fabrication, considerable knowledge of building maintenance and repair activities, good organizational, interpersonal and decision making skills and sufficient strength and agility to perform the physically demanding aspects of the job in a variety of weather conditions. Job performance is evaluated by the Solid Waste Director through review of daily repair work and preventive maintenance activities on trucks and machinery, level of support provided for building maintenance activities, accuracy of job related information related to the procurement and purchase of parts and equipment, diagnostic capabilities and quality of the repair work performed. Illustrative Examples of Work -Performs minor repair work and preventive maintenance activities on solid waste trucks, vehicles, machinery and equipment. -Troubleshoots and diagnoses equipment malfunctions to determine needed repairs. -Rebuilds and/or repairs electrical, cooling, suspension, and braking components and systems.
    [Show full text]
  • Estimating Reversible Pump-Turbine Characteristics
    A WATER RESOURCES TECHNICAL PUBLICATION ENGINEERING MONOGRAPH NO. 39 Estimating Reversible Pump-TurbineCharacteristics UNtTED STATES DEPARTMENT OF THE INTERIOR BUREAU OF RECLAMATlON MS-230 (l-76) Bureau of Reclamation TECHNICAL REiPORT STANDARD TITLE PAG 3. RECIPIENT’S CATALOG NO. 4. TITLE AND SUBTITLE 5. REPORT DATE Estimating Reversible Pump-Turbine December 1977 Characteristics 6. PERFORMING ORGANIZATION CODE 7. AUTHOR(S) 6. PERFORMING ORGANIZATION REPORT NO. R. S. Stelzer and R. N. Walters Engineering Monograph 39 9. PERFORMING ORGANIZATION NAME AND ADDRESS 10. WORK UNIT NO. Engineering and Research Center Bureau of Reclamation 11. CONTRACT OR GRANT NO. Denver, CO 80225 13. TYPE OF REPORT AND PERIOD COVERED 2. SPONSORING AGENCY NAME AND ADDRESS Same 14. SPONSORING AGENCY CODE 5. SUPPLEMENTARY NOTES 6. ABSTRACT The monograph presents guidelines for designers who plan or maintain pump-turbine installations. Data are presented on recent installations of pump-turbines which include figures showing operating characteristics, hydraulic performance, and sizing of the unit. Specific speed, impeller/ runner diameter, and the best efficiency head and discharge were aelectei as the criteria that characterize the unit performance. 7. KEY WORDS AND DOCUMENT ANALYSIS I. DESCRIPTORS-- / pumped storage/ *pump turbines/ powerplants/ reversible turbines/ Francis turbines/ pumps/ power head/ turbine efficiency/ specific speed/ cavitation index/ hydraulic machinery/ design criteria ). IDENTIFIERS-- / Flatiron Powerplant, CO/ Mt. Elbert Pumped-Storage Power- plant, CO/ Grand Coulee Pumping Plant, WA/ San Luis Pumping-Generating/ Senator Wash Dam, CA/ :. COSATI Field/Group 13G COWRR: 1307.1 6. DISTRIBUTION STATEMENT 19. SECURITY CLASS pt. NO. OF PAGI ITHIS REPORT) \voiloble from the National Technical Information Service, Operations UNCLASSIFIED division, Springfield.
    [Show full text]
  • Hydraulic Machinery • Turbine Is a Device That Extracts Energy from a Fluid (Converts the Energy Held by the Fluid to Mechanical Energy)
    Hydraulic Machines power point presentation Slides has been adapted from Hydraulic Machines, K. Subramanya 2016-2017 Prepared by Dr. Assim Al-Daraje 1 Chapter (1 Part 1) Prepared by Dr. Assim Al-Daraje INTRODUCTION 2 Hydraulic machinery • Turbine is a device that extracts energy from a fluid (converts the energy held by the fluid to mechanical energy) • Pumps are devices that add energy to the fluid (e.g. pumps, fans, blowers and compressors). 3 INTRODUCTION Fluid-flow machines are very broadly classified as turbo-machines and positive displacement machines. A turbo-machine is a device that adds energy to a fluid or extracts energy from the fluid by virtue of a rotating system of blades. These machines require a rotating element called rotor and relative motion between the fluid and the rotor. 4 If the machine adds energy it is called a pump; if it extracts energy it is called a turbine. The fluid to be pumped can be in incompressible mode throughout its passage in the machine or compressibility effects may come in to picture at different phases of its interaction in the machine. If the fluid is water, the pump device is labeled as water pump. 5 Turbines • J.V. Poncelet first introduced the idea of the development of mechanical energy through hydraulic energy • Modern hydraulic turbines have been developed by L.A. Pelton (impulse), G. Coriolis and J.B. Francis (reaction) and V Kaplan (propeller) 6 A-Pelton Wheel, B-Francis, Turbine, C-Kaplan Turbine 7 Pelton (impulse) 8 9 Kaplan (propeller) 10 11 Turbines • Hydro electric power is the most remarkable development pertaining to the exploitation of water resources throughout the world • Hydroelectric power is developed by hydraulic turbines which are hydraulic machines.
    [Show full text]
  • Theoretical Simulation of Static and Dynamic Behavior of Electro-Hydraulic Servo Valves
    Scientific Bulletin of the The 6th International Conference on Politehnica University of Timisoara Hydraulic Machinery and Hydrodynamics Transactions on Mechanics Special issue Timisoara, Romania, October 21 - 22, 2004 THEORETICAL SIMULATION OF STATIC AND DYNAMIC BEHAVIOR OF ELECTRO-HYDRAULIC SERVO VALVES Victor BALASOIU, Prof.* Mircea Octavian POPOVICIU, Prof. Department of Hydraulic Machinery Department of Hydraulic Machinery “Politehnica” University of Timisoara “Politehnica” University of Timisoara Ilare BORDEASU, Assoc. Prof. Department of Hydraulic Machinery “Politehnica” University of Timisoara *: Bv Mihai Viteazu 1, 300222, Timisoara, Romania, Tel.: (+40) 256 403681, Fax: (+40) 256 403700, (+) 256 4030682, Email: [email protected], [email protected] ABSTRACT The electro-hydraulic servo-valves (EHSV) as in- range Yoi and the clearance J over the linearity degree terface in automatic hydraulic systems are in essence and the magnitude of the adjusted flow. hydroelectric directional control valves with cylindrical The model of the dynamic equilibrium of the spool spool, with integral reaction. The output quantity valve is defined starting with the computation of forces (flow rate, pressure) is modified proportional with acting on the spool. Introducing the concept of interac- the control signal (voltage, current) together link tion between the aggregate components nozzle-spool- (electrical, hydraulic or mechanical). Both the manner distributor it was defined the mathematical model for in which the reaction signal is produced and the the directional spool valve as a whole. position of the information circuit where it is applied, After defining the transfer function, both analyze characterises the type but also static and dynamic and syntheses of performances were possible for the behavior of the servo valve.
    [Show full text]
  • The Influence of Gear Micropump Body Asymmetry on Stress Distribution
    POLISH MARITIME RESEARCH 1 (93) 2017 Vol. 24; pp. 60-65 10.1515/pomr-2017-0007 THE INFLUENCE OF GEAR MICROPUMP BODY ASYMMETRY ON STRESS DISTRIBUTION Wacław Kollek, Prof. Piotr Osiński Urszula Warzyńska Wrocław University of Science and Technology, Poland ABSTRACT The paper presents the results of numerical calculations of stress distributions in the gear micropump body for applications in hydraulic systems, especially in the marine sector. The scope of the study was to determine the most favorable position of bushings and pumping unit in the gear pump body in terms of stress and displacement distribution in the pump housing. Fourteen cases of gear pump bushings and pumping unit locations were analyzed: starting from the symmetrical position relative to the central axis of the pump, up to a position shifted by 2.6 mm towards the suction channel of the pump. The analysis of the obtained calculation results has shown that the most favorable conditions for pump operation are met when the bushings are shifted by 2.2 mm towards the suction channel. In this case the maximal stress was equal to 109 MPa, while the highest displacement was about 15µm. Strength and stiffness criteria in the modernized pump body were satisfied. Keywords: gear micropump, microhydraulics, finite element method 17, 19, 20, 21, 22]. The development of modern gear units is INTRODUCTION associated with the following trends: increasing operating pressure [6, 18], improving total efficiency [4, 10, 15, 18, 23], Gear pumps are the most common group of positive reducing pressure pulsations [3, 18, 25], minimizing weight displacement pumps used in hydrostatic drive systems as [15] and noise [11, 14, 16], and reducing dynamic loads [7, 12, power generators, as well as in lubrication systems in various 13, 19].
    [Show full text]
  • Hydraulics & Oil Power Systems Automation Guidebook
    PDHonline Course M523 (8 PDH) _____________________________________________________ Hydraulics & Oil Power Systems Automation Guidebook – Part 2 Instructor: Jurandir Primo, PE 2014 PDH Online | PDH Center 5272 Meadow Estates Drive Fairfax, VA 22030-6658 Phone & Fax: 703-988-0088 www.PDHonline.org www.PDHcenter.com An Approved Continuing Education Provider www.PDHcenter.com PDHonline Course M523 www.PDHonline.org HYDRAULICS & OIL POWER SYSTEMS AUTOMATION GUIDEBOOK – PART 2 CONTENTS: INTRODUCTION BASIC PRINCIPLES OF HYDRAULICS HYDRAULIC OIL PROPERTIES HYDRAULIC DRIVE SYSTEMS HYDRAULIC SYSTEMS – BASIC CALCULATIONS HYDRAULIC VALVES TYPES AND FUNCTIONS OF VALVES DIRECTIONAL CONTROL VALVES CYLINDERS AND ACTUATORS CYLINDER CONTROL DIAGRAMS HYDRAULICS & PNEUMATICS - DIFFERENCES BASIC ELECTRO-HYDRAULIC CONTROL HYDRAULICS – SOFTWARE SIMULATIONS HYDRAULICS & PNEUMATICS – BASIC DESCRIPTION HYDRAULICS – TRAINING LINKS AND REFERENCES ©2014 Jurandir Primo Page 1 of 116 www.PDHcenter.com PDHonline Course M523 www.PDHonline.org INTRODUCTION: The word hydraulics is a derivative of the Greek words hydro (meaning water) and aulis (meaning tube or pipe). Originally, the science of hydraulics only covered the physical behavior of water at rest and in motion. The use has broadened its meaning, to include compressed air or gases and oil com- pounds and other confined liquids commonly used under controlled pressure to do some work. Hydraulics can be defined as the engineering science that pertains to liquid pressure and flow. This study includes the manner in which liquids act in tanks, cylinders, hoses, valves and pipes, dealing with their properties and the common ways of utilizing these properties to create motion. It includes the laws of floating bodies and the behavior of fluids under various conditions, and ways of directing this flow to useful ends, as well as many other related subjects and applications.
    [Show full text]
  • Hydraulic Machinery Made Easy
    Product Catalogue 2017 Hose I Fittings I Accessories Hydraulic Machinery Made Easy The Easy Choice for Lubrication & Hydraulics PB 1 Dear Customer, Welcome to the Armadillo Group third edition of Hydraulic hose and fitting product guide. Are you looking for another solution to those problems you often have in this industry? Or maybe you are just looking for the good old fashioned service you use to get? Or maybe your problem lies deeper in a maze of technical jargon? Whatever your problem is, our aim is to fill the gap, to provide the easy choice in lubrication and hydraulics. With products sourced from quality suppliers all over the globe we are sure to be able to meet your expectations. Having one of the best stock holdings in the country we are able to offer premium service when you need it most. We hope this catalogue will be of assistance to you not only as a product guide but as a handy reference for threads, hose sizes and other technical information and we look forward to hearing from you soon. Best Regards TheThe Team Team at Armadillo Group The Easy Choice for Lubrication & Hydraulics | www.armadillogroup.com.au CONTENTS CONTENTS Introduction and Information Section 1 9 - 22 Adaptors Section 2 23 - 28 Hose Tails Section 3 29 - 31 4 Wires Hose Tails Section 4 32 - 36 4 Wires Hose Tails Section 5 37 - 48 Ferrules Section 6 49 - 52 Hose Section 7 53 - 57 Hydraulic Components Section 8 58 - 73 Technical HOSE TAIL NOMENCLATURE RHCM 05 12 08 Hose Connector Hose Tail Size Style Thread Size NOTE: Please note Armadillo Group refers to thread sizes only, not dash size as this is universal language.
    [Show full text]
  • Energy Efficiency Comparison of Hydraulic Accumulators And
    energies Article Energy Efficiency Comparison of Hydraulic Accumulators and Ultracapacitors Jorge Leon-Quiroga 1, Brittany Newell 1, Mahesh Krishnamurthy 2, Andres Gonzalez-Mancera 3 and Jose Garcia-Bravo 1,* 1 Purdue Polytechnic School of Engineering Technology, Purdue University, West Lafayette, IN 47907, USA; [email protected] (J.L.-Q.); [email protected] (B.N.) 2 Department of Electrical and Computer Engineering, Illinois Institute of Technology, Chicago, IL 60616, USA; [email protected] 3 Department of Mechanical Engineering, Universidad de los Andes, Bogota 111711, Colombia; [email protected] * Correspondence: [email protected] Received: 21 February 2020; Accepted: 20 March 2020; Published: 2 April 2020 Abstract: Energy regeneration systems are a key factor for improving energy efficiency in electrohydraulic machinery. This paper is focused on the study of electric energy storage systems (EESS) and hydraulic energy storage systems (HESS) for energy regeneration applications. Two test benches were designed and implemented to compare the performance of the systems under similar operating conditions. The electrical system was configured with a set of ultracapacitors, and the hydraulic system used a hydraulic accumulator. Both systems were designed to have the same energy storage capacity. Charge and discharge cycle experiments were performed for the two systems in order to compare their power density, energy density, cost, and efficiency. According to the experimentally obtained results, the power density in the hydraulic accumulator was 21.7% higher when compared with the ultracapacitors. Moreover, the cost/power ($/Watt) ratio in the hydraulic accumulator was 2.9 times smaller than a set of ultracapacitors of the same energy storage capacity.
    [Show full text]
  • CE 378 Water Resources Engineering Term: Spring 2013 CE 378 Water Resources Engineering (3)
    CE 378 Water Resources Engineering Term: Spring 2013 CE 378 Water Resources Engineering (3). Three hours 1:00 to 1:50 M, W and F, room 254 Hardaway Hall Instructor: Robert E. Pitt, Ph.D., P.E., BCEE, D. WRE Office: 1005A Bevill Office Hours: M and W 3 to 4 pm; when in town, or by appointment; by email anytime Phone: (205) 348-2684 e-mail: [email protected] (UA) or [email protected] (home) TA: Redahegn Sileshi ([email protected]) Catalog Mechanics of steady and unsteady flow in closed and open conduits, hydrology; water Description supply and wastewater disposal. Prerequisites Dynamics (AEM 264) and Fluid Mechanics (AEM 311); or Fluid Flow Operations (ChE 304) Co requisites none Course This course is directed to applications of fluid mechanics, hydrology, and hydraulics as Objectives they apply to the discipline of water resources engineering. Topics covered include flow in closed conduits and open channels, hydraulic machinery (pumps), and surface water hydrology and statistical methods. Student projects will be directed to simple designs of sustainable urban water-use and water-control systems. At the successful completion of this course, the student will be able to apply the fundamental principles of conservation of mass, momentum and energy to the practical solution of both analysis and design problems in closed and open conduit flows, and will understand the performance characteristics of pumps. The student will also be introduced to hydrology and to methods of quantification of hydrologic uncertainty. Course Website Located at: http://unix.eng.ua.edu/~rpitt/Class/Water%20Resources %20Engineering/WREMainPage.htm Required Texts There are no required texts for the class, as much of the reference material is readily and References available from several sources, including the class website noted above.
    [Show full text]
  • Design and Evaluation of Hydraulic Suspension Without Spring In
    CORE Metadata, citation and similar papers at core.ac.uk Provided by MAT Journals Journal of Mechanical and Mechanics Engineering Volume 4 Issue 2 Design And Evaluation Of Hydraulic Suspension Without Spring In LMV K.Ravishankar1, S.Anandakumar2 1PG Student, Dept of MechanicalEngg, ShreeVenkateshwara HI Tech Engineering College, Gobichettipalayam, Tamilnadu 2Assistant professor, Dept of Mechanical Engg, Shree Venkateshwara HI Tech Engineering College, Gobichettipalayam, Tamilnadu [email protected], [email protected] Abstract - The suspension is the backbone of all Apart from that safe driving plays an important vehicles its principle function is to safely carry the role in automobile. When the level of maximum load for all designed operating conditions. suspension reduces it leads to increase in noise. This project defines design and evaluation of By using hydraulic suspension we can reduce hydraulic suspension without spring in LMV. Shock the vibration and also improve riding comfort. reduction is an important characteristic which reduces Auto manufacturers are still trying to catch up with the vibration of the vehicle and carries the load safely. the combination of features offered by this hydraulic In this project a hydraulic suspension is used to suspension system, typically by adding layers of produce hydraulic pressure that negates external complexity to an ordinary steel spring mechanical forces acting on the vehicle. As a result, the system. suspension system is able to control vehicle movement freely and continuously. This control ACTIVE SUSPENSION capability makes it possible to provide higher levels of ride comfort and vehicle dynamics which obtained A. INTRODUCTION OF ACTIVE SUSPENSION with conventional suspension systems. The design A suspension is self-propelledequipmentit controls was done using CREO PARAMETRIC 2.0 and the the upright movement of all the wheels via an model is imported to Proficy / SCADA (IFix version onboard system reasonably than the effort being 4.0) for evaluation.
    [Show full text]
  • University of Macau Undergraduate Civil Engineering Programme
    University of Macau Undergraduate Civil Engineering Programme Coordinating Unit: Department of Civil and Environmental Engineering, Faculty of Science and Technology Supporting Unit(s): Nil Course Code: CIVL341 Year of Study: 3 Course Title: Hydraulics II Compulsory/Elective: Compulsory Course Prerequisites: CIVL230 Hydraulics I Prerequisite Entry level fluid mechanics Knowledge: Duration: One semester Credit Units: 4 Class/Laboratory Three hours of lecture and one hour of tutorial and one hour of laboratory per week. Schedule: Laboratory/Software Hydraulics Laboratory Usage: Application of the basic laws of fluid mechanics to hydraulic problems. Analysis of simple and multiple steady pipe flows: branching pipes, pipes in series and parallel, and pipe network; flow measurement in pipe. Unsteady flow in pressure conduits: establishment of steady flow and water hammer. Analysis of pumps and turbines. Pump and system Course Description: characteristics. Steady open channel flow: energy and momentum principles; critical and uniform flow development and their computation; best hydraulic section; gradually varied flow and its profile computation; flow measurement in open channel. Introduction to Hydrology. 1. Apply fundamental principles of fluid mechanics for the solution of practical civil engineering problems of water conveyance in pipes, pipe networks, and open channels. 2. Describe the operating characteristics of hydraulic machinery (pumps and turbines), and the factors affecting their operation and specifications, as well as their operation in Course Objectives: a system. 3. Describe the principles controlling open channel flows including critical, uniform and gradually varied flows. Design of channel section for uniform flow. 4. Introduce some basic topics of engineering hydrology. Upon completion of this course, students should be able to: 1.
    [Show full text]
  • The Hydraulic-Machinery Laboratory at the California Institute of Technology
    (Reprinted from the A.S.M.E. Tramactionll for NO'Dember, 1958) The Hydraulic-Machinery Laboratory at the California Institute of Technology BY R. T. KNAPP,' PASADENA, CALIF. Tbis paper gives a description of the arrangement, heads of from 146 ft for the lowest to 444 ft for the highest. equipment, and instrumentation of the hydraulic-ma­ Very little precedent was available for plants of such size, to chinery laboratory at the California Institute of Tech­ assist the engineers of the District in answering questions con­ nology. This laboratory was designed essentially to work cerning maximum permissible head per stage, single- or double­ with problems involving high heads, high speeds, and suction pumps, optimum speeds, attainable efficiencies, and moderately large powers and rates of flow. The instru­ desirable operating characteristics. It was felt that a properly ments and equipment permit both speed and precision equipped laboratory would be of great assistance in studying in testing, an overall accuracy ofO.l per cent being attain­ such problems, and would amply justify the expense required, able. For the past two years the laboratory has been u sed both by savings expected and by the insurance of obtaining the for the study of pumping problems of the Colorado River most satisfactory type of equipment. aqueduct, a project which will have pumps totaling 350,000 The responsibility of supervising the design, construction, and hp when completed. operation of the laboratory was placed in the hands of a group consisting of Professors Th. von Karman, R . L. Daugherty, and HE Hydraulic-Machinery Laboratory is a joint enterprise R .
    [Show full text]