DOCSLIB.ORG

Serial (RS-232) Commands

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Serial (RS-232) Commands Serial (RS-232) Commands Chapter 8 Serial (RS-232) Commands Overview The 7330 Controller has two serial port connectors on the rear panel of the controller labeled RS232-1 and RS232-2. Either port can be configured as the Console port, the port that you use to enter commands to the repeater controller and to perform firmware updates. Whichever port is not being used as the Console port can be used as the Auxiliary port. The 7330 Repeater firmware accepts commands on the Console port. This serial port has a dedicated command queue so that commands can be processed without being delayed by user commands from the DTMF decoders. Commands entered via the serial port have the same format as commands entered via DTMF. The Auxiliary port is currently unused. This chapter describes the uses of the Console port, the command formats, sending a text file of commands, managing files in your controller, and configuring the serial ports. 8-1 7330 Chapter 8 Using the Console Port The Console port has a number of different uses and sets of commands depending on what firmware is running in the 7330 Controller. By default, the 7330 Repeater firmware is controlling the radio equipment attached to the controller. Other firmware installed in the controller, called SBOOT, allows you to manage the files stored in the flash memory of the controller. When power is first applied to the controller, the firmware outputs the following message on the Console port: S-COM 7330 Repeater V3.3 This message tells you what firmware is running and it’s version. In the above example the version is 3.3. If the firmware is starting as a result of a Cold Start (see page 2-3), the 7330 Repeater firmware will confirm that it erased your programming by sending this message: Cold Reset The startup routine of the firmware also checks the condition of the controller’s internal coin cell battery on every reset of the controller and outputs its status: Battery OK or: Battery Low When the firmware is ready for you to type a command, it outputs the 7330 Repeater prompt: > So, the startup screen looks like this on a Cold Start: S-COM 7330 Repeater V3.3 Cold Reset Battery OK > and like this on other resets: S-COM 7330 Repeater V3.3 Battery OK > 8-2 Serial (RS-232) Commands Entering Commands You enter commands to the 7330 Repeater firmware by typing an ASCII or DTMF command on a single line and then pressing Enter. (See the next section for command formats.) The 7330 Repeater firmware outputs a command response text response message for each command you enter. For DTMF-compatible commands, the command response is the text version of what you would hear as a CW or speech response message from the controller when you enter a command via a DTMF decoder: CW Response Serial Port Response OK OK ? err 1 Error: Wrong number of digits ? err 2 Error: Incorrect digits ? not found Error: Macro name not found ? dir full Error: Macro directory full ? too big Error: Macro exceeds 200 digits ? name used Error: Macro name already exists ? last Error: Macro, cannot delete last command Error: Line too long Error: Invalid DTMF character Error: Serial input overflow or receive error If the command you enter causes an audio message to be played, that message is played on Transmitter #1. The ver command displays the name and version of the 7330 Repeater firmware: S-COM 7330 Repeater V3.3 The sboot command causes the 7330 Repeater firmware to temporarily stop executing and the SBOOT utility to execute instead. The SBOOT utility is used to manage the files stored in the flash memory of the controller. (See the File Management section later in this chapter.) Commands and comments can be typed into a text file. This file can be sent to the 7330 Controller using the Send File feature of your terminal emulator. (See the Terminal Emulator section later in this chapter.) 8-3 7330 Chapter 8 Controller Command Format There are two types of commands supported by the 7330 Repeater firmware. ASCII commands implement functions only available via the serial port. DTMF- compatible commands can be entered either on the serial port or a radio port via the DTMF buttons on your radio. ASCII Commands The following ASCII commands are implemented in the 7330 Repeater firmware. Both upper case and lower case are accepted. Command Description VER Displays the version of the 7330 Repeater firmware. SBOOT Stops the 7330 Repeater firmware and begins execution of the SBOOT utility. This utility allows configuration of the serial ports and provides firmware update facilities. DTMF-Compatible Commands DTMF-compatible commands are sequences of digits that represent valid instructions for the controller. Each command is entered on one line and ends with Enter (also known as a CR/LF): 994501000*(Enter) The asterisk that normally ends a DTMF command is optional for serial commands when no comment follows the command on the same line: 994501000(Enter) A command may optionally begin with an exclamation point (!). Accepting an exclamation point makes the command line compatible with the 7KDAB format: !994501000(Enter) To execute a macro, send the macro’s name: 6500*(Enter) 8-4 Serial (RS-232) Commands Spaces Any number of spaces or tabs may be inserted in commands or comments to make them more readable. The spaces and tabs are ignored: 99 45 0100 0 *(Enter) Comments Comments begin with a semicolon (;) and can be placed on a line by themselves: ; TX1 Identifier Message Interval(Enter) or at the end of lines containing commands: 99 09 2106 570 * ; 9.5 Minutes/570 seconds(Enter) When a comment is on the same line as the command, the asterisk terminating the command is required. Sending a Text File of Commands (Batch Downloads) To make it easier to manage the programming of your controller, you can type your commands and comments into a text file using a text editor like Notepad on Windows™. Then, you can use the feature of your terminal emulator to send this file to the controller. Before sending your file to the controller, set up the terminal emulator serial port configuration’s delay parameters. (See the Terminal Emulator section later in this chapter.) By configuring these parameters, you will ensure that the commands will be properly recognized by the controller. The feature of the terminal emulator you will use to send your file is the Send Text File feature. Each terminal emulator has this command, though it might work slightly differently in each one. Check the manual for your terminal emulator for specifics. When you send the file of commands to the controller, each command is executed by the controller as it is received and a response is sent. This will continue for each of the commands that you typed into the file. 8-5 7330 Chapter 8 File Management While the sboot command is running you will see these changes: The 7330 Repeater firmware is no longer operating. The repeaters controlled by the controller appear to be dead. The logic output state is maintained. The front panel LEDs scan left-to-right to remind you that the repeaters are not operating. The command prompt changes to SBOOT>. The SBOOT utility outputs the following menu. You can redisplay this menu at any time by typing the help command, h, then pressing enter. SCOM 7330 SBOOT V1.2 7330 Controller Storage Management T - Show Time Tmmddyyhhmmssw - Set Time (w=0=Sunday) S - Save Repeater Configuration R - Restore Repeater Configuration E - Erase Files L - Load File from a PC to Flash U - Upload File from Flash to a PC D - Display Flash Directory P - Set Baudrate of Console Port N - Set Baudrate of Auxiliary Port W - Set Console Port Number B - Boot from Flash X - Reboot SBOOT from Flash H - Help Time: 091011-121513-6 Battery OK. WARNING: AUX1 Jumper Installed. Must be removed for unattended repeater operation! WARNING: AUX2 Jumper Installed. Must be removed for unattended repeater operation! SBOOT> Each section of the SBOOT utility display shows a group of related information. These groups are described below. 8-6 Serial (RS-232) Commands SBOOT Version The first line of the output display shows the name of the firmware and its version: SCOM 7330 SBOOT V1.2 Managing the Controller Time-of-Day Clock Following the menu, you will see the current time from the controller’s clock: Time: 091011-121513-6 Verify that the time-of-day is correct. If the time needs to be changed, you can use the following menu items: T - Show Time Tmmddyyhhmmssw - Set Time (w=0=Sunday) to review the current time and to set the time-of-day clock. Managing the Repeater Firmware Configuration The following menu items: S - Save Repeater Configuration R - Restore Repeater Configuration let you manage the configuration of the Repeater firmware. Multiple configurations can be saved to the controller’s flash memory. You can select if you would like to return repeater operation to a previously saved configuration. Note: This feature coming soon! 8-7 7330 Chapter 8 Managing Firmware You can use the following menu items to manage the firmware that’s installed in your controller. E - Erase Files L - Load File from a PC to Flash U - Upload File from Flash to a PC D - Display Flash Directory The Display Flash Directory command is the one most often used. Controller Information Model Number : 7330 Serial Number : Proto2 Manufactured DT: 091709-065554-4 Formatted DT : 091709-065458-4 Customer Name : Dave's Beta Firmware Files Location Name Version Date Type ------------- ---------------- -------- ---------------- -------------------- SBOOT 7330_SBoot 1.2.1 12/22/2009 Program MFG No File DIAG 7330_Diag 1.2.0 9/4/2009 Program SCOM_A 7330 3.2.2 11/7/2010 Program SCOM_B No File Configuration Files Location Name Version Date Type ------------- ---------------- -------- ---------------- -------------------- RESTORE_A No File RESTORE_B No File Speech Files Location Name Version Date Type ------------- ---------------- -------- ---------------- -------------------- LIB SCOM Sp Lib Eng 1.2.0 5/8/2011 Speech Library CUSTOM SCOM Cust ALib 1.0.0 09/09/09 12:00 Custom Audio Library With this command you can confirm the version of the files that are installed in your controller.
Load more

Recommended publications
  • Multiview Terminal Emulator User Guide © 2008 by Futuresoft, Inc
    MultiView Terminal Emulator User Guide © 2008 by FutureSoft, Inc. All rights reserved. MultiView User Guide This manual, and the software described in it, is furnished under a license agreement. Information in this document is subject to change without notice and does not represent a commitment on the part of FutureSoft. FutureSoft assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual. No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or other wise, without the prior, written per- mission of FutureSoft, Inc. MultiView 2007, MultiView 2000 Server Edition, MultiView 2008 Server Edition, MultiView Catalyst, MultiView License Manager, MultiView DeskTop and Host Support Server are tradenames of FutureSoft, Inc. Edition 1 May 2008 Document #E-MVUG-MV2007-P053108 Last Updated: 102308 FutureSoft, Inc. 12012 Wickchester Lane, Suite 600 Houston, Texas 77079 USA Printed in the USA 1.800.989.8908 [email protected] http://www.futuresoft.com Table of Contents Contents Chapter 1 Introduction Introduction to MultiView 2007 ....................................................................................... 2 Minimum Requirements .................................................................................................. 2 Contacting FutureSoft Support ........................................................................................ 3 Chapter 2 Installation and Configuration Installing MultiView
    [Show full text]
  • AVR244 AVR UART As ANSI Terminal Interface
    AVR244: AVR UART as ANSI Terminal Interface Features 8-bit • Make use of standard terminal software as user interface to your application. • Enables use of a PC keyboard as input and ascii graphic to display status and control Microcontroller information. • Drivers for ANSI/VT100 Terminal Control included. • Interactive menu interface included. Application Note Introduction This application note describes some basic routines to interface the AVR to a terminal window using the UART (hardware or software). The routines use a subset of the ANSI Color Standard to position the cursor and choose text modes and colors. Rou- tines for simple menu handling are also implemented. The routines can be used to implement a human interface through an ordinary termi- nal window, using interactive menus and selections. This is particularly useful for debugging and diagnostics purposes. The routines can be used as a basic interface for implementing more complex terminal user interfaces. To better understand the code, an introduction to ‘escape sequences’ is given below. Escape Sequences The special terminal functions mentioned (e.g. text modes and colors) are selected using ANSI escape sequences. The AVR sends these sequences to the connected terminal, which in turn executes the associated commands. The escape sequences are strings of bytes starting with an escape character (ASCII code 27) followed by a left bracket ('['). The rest of the string decides the specific operation. For instance, the command '1m' selects bold text, and the full escape sequence thus becomes 'ESC[1m'. There must be no spaces between the characters, and the com- mands are case sensitive. The various operations used in this application note are described below.
    [Show full text]
  • Interfacing the ESP8266 Wireless Terminal Contents 1 Introduction
    Interfacing the ESP8266 Wireless Terminal Ondřej Hruška Katedra měření, FEL ČVUT March 2, 2017 Contents 1 Introduction1 2 Feature overview2 2.1 Terminal implementation........................2 3 Interfacing the terminal3 3.1 UART connection............................3 3.2 Debug port................................4 3.3 Control codes and escape sequences...................4 3.3.1 Escape sequences.........................4 3.3.2 Colors and attributes......................6 3.3.3 Cursor movement.........................6 3.3.4 Clearing commands.......................7 3.3.5 Screen scrolling..........................7 3.3.6 Cursor memory..........................7 3.4 System commands............................7 3.4.1 Query commands.........................8 3.4.2 Changing screen size.......................8 3.4.3 Factory reset...........................8 3.5 User input.................................8 4 WiFi configuration9 5 Useful links 10 1 Introduction The purpose of this document is to present the ESP8266 Wireless Terminal firmware and describe how the module can be interfaced by an external microcontroller. Ondřej Hruška Katedra měření, FEL ČVUT This document is divided into three sections: the first part explains the internal makeup of the module and it’s possibilities, then we move on to the supported control sequences and details of the communication protocol, and in the last part the wireless settings are discussed. 2 Feature overview The module implements a simple, VT100-compatible terminal emulator with a screen of up to 25x80 characters, controlled by ANSI escape sequences for col- ors, cursor movement and screen manipulation. It’s capable of displaying received characters, as well as receiving input from the keyboard or mouse and sending those back over the serial line. The user can access the terminal screen using their web browser thanks to a tiny built-in webserver, after connecting to the module over WiFi.
    [Show full text]
  • Introduction to UNIX Manual
    UNIX Introduction to UNIX Manual Michael Gribskov V2018.3 24 August 2018 1 Contents Connecting to servers ................................................................................................................................... 4 Windows ................................................................................................................................................... 4 MobaXterm (recommended) ................................................................................................................ 4 PUTTY .................................................................................................................................................... 5 OS X/MacOS/Linux .................................................................................................................................... 6 SSH ........................................................................................................................................................ 6 Cyberduck ............................................................................................................................................. 6 Edit server files .................................................................................................................................. 7 Transferring files ............................................................................................................................... 7 Purdue University Specific .......................................................................................................................
    [Show full text]
  • Mac Os Serial Terminal App
    Mac Os Serial Terminal App Panting and acetous Alaa often scag some monoplegia largo or interdict legitimately. Tourist Nikita extemporised or Aryanised some dop quick, however unsectarian Merwin hectograph globularly or emotionalize. Germaine is know-nothing and sodomizes patronizingly as modiolar Osborne bug-outs unconstitutionally and strides churchward. Can choose a usb to dim the app mac os sector will happen, and act as commented source code is anyone else encountered this Tom has a serial communication settings. Advanced Serial Console on Mac and Linux Welcome to. Feel free office helps you verify that makes it takes a terminal app mac os is used for a teacher from swept back. Additionally it is displayed in the system profiler, you can also contains a cursor, you can i make use these two theme with the app mac os is designed to. Internet of Things Intel Developer Zone. Is based on the latest and fully updated RPiOS Buster w Desktop OS. Solved FAS2650 serial port MAC client NetApp Community. Mac Check Ports In four Terminal. A valid serial number Power Script Language PSL Programmers Reference. CoolTerm for Mac Free Download Review Latest Version. Serial Port Drivers and Firmware Upgrade EV West. Osx ssh If you're prompted about adding the address to the heritage of known hosts. This yourself in serial terminal open it however, each device node, i have dozens of your setting that the browser by default in case. 9 Alternatives for the Apple's Mac Terminal App The Mac. So that Terminal icon appears in the Dock under the recent apps do the.
    [Show full text]
  • How to Use Your Windows PC As an X-Windows Terminal Emulator to Run Athena Sessions
    How to use your Windows PC as an X-windows Terminal Emulator to run Athena Sessions If you prefer not to go to an Athena cluster to run tsuprem4, you can use your laptop or desktop PC, connected to Athena, as an X-windows terminal emulator. In this case, your PC emulates an x-windows terminal. You are still running tsuprem4 on an Athena Unix (Sun- Solaris) machine. The instructions to configure your PC as an x-windows emulator are listed below: Please go to http://web.mit.edu/software/win.html and download the following software: SecureCRT 5.1 X-Win32 8.2 Install this software on your PC and run them. In SecureCRT do the following actions: File...Connect....New Session (3rd tab on top) and fill the table with proper settings as can be seen in the following image: Fill the username field with your Kerberos username and press OK to run and insert your password. Run Xwin32 or Exceed if you have it (Exceed is not available on the MIT website but is available for purchase). In order to see images when running tsuprem4, you need to adjust the DISPLAY system variable according to your IP address. A simple way of getting your IP address, is typing the "setenv" command in SecureCRT screen. You will see something similar to this (with different numbers/characters): USER=pouya LOGNAME=pouya HOME=/afs/athena.mit.edu/user/p/o/pouya PATH=/srvd/patch:/usr/athena/bin:/usr/athena/etc:/bin/athena:/usr/openwin/bin:/usr/open win/demo:/usr/dt/bin:/usr/bin:/usr/ccs/bin:/usr/sbin:/sbin:/usr/sfw/bin:/usr/ucb:.:/mit/avant i/arch/sun4x_510/bin:/mit/matlab/arch/sun4x_510/bin:/mit/maple/arch/sun4x_59/bin MAIL=/var/mail//pouya SHELL=/bin/athena/tcsh TZ=US/Eastern SSH_CLIENT=18.62.30.76 2304 22 SSH_CONNECTION=18.62.30.76 2304 18.7.18.74 22 SSH_TTY=/dev/pts/59 .....
    [Show full text]
  • Technical Note 1
    NOAA Pacific Marine Environmental Laboratory Ocean Climate Stations Project TECHNICAL NOTE 1 Ocean Climate Stations High-Latitude Buoy Set Up and Deployment Manual Version 2.1 February 2013 NOTICE Mention of a commercial company or product does not constitute an endorsement by NOAA/PMEL. Use of information from this publication concerning proprietary products or the tests of such products for publicity or advertising purposes is not authorized. Current manual version edited by Jennifer Keene. Contributions made to v1 – v1.5b by Patrick A'Hearn, Robert Kamphaus, Keith Ronnholm, and Patrick McLain. www.pmel.noaa.gov/ocs February 2013 Table of Contents Overview.................................................................................................................................1 Buoy Components and Shipping..............................................................................................2 Buoy Assembly........................................................................................................................4 Instrument Well .............................................................................................................................. 4 Tower.............................................................................................................................................. 5 Bridle............................................................................................................................................... 6 Load Cell.........................................................................................................................................
    [Show full text]
  • TMS Terminal Emulator Interface Instructions (Text Based) for the Thermal Management System (TMS)
    TMS Terminal Emulator Interface Instructions (Text based) for the Thermal Management System (TMS) Part Number: TMSB00000-01 Fan speed controller, 1 to 4 fans, 11-57V supply, highly configurable, alarm monitoring, enclosure. Copyright (c) ebm-papst UK Ltd 2015 This document, including any concepts or techniques used, is the intellectual property of ebm-papst UK Ltd. ebm-papst UK Ltd Chelmsford Business Park Chelmsford Essex CM2 5EZ Tel: +44 (0) 1245 468555 Fax: +44 (0) 1245 466336 www.ebmpapst.co.uk The most recent version of this document is available for download at: www.ebmpapst.co.uk/instructions Page 1 of 22 210-OMI13963 INDEX 1 INSTALLATION OF CONFIGURATION SOFTWARE ON PC ....................................... 3 1.1 REQUIRED CONFIGURATION TOOLS .......................................................................... 3 1.2 CONFIGURATION SOFTWARE INSTALLATION INSTRUCTIONS ......................................... 3 1.3 CONFIGURATION INTERFACE FAULT FINDING .............................................................. 4 2 CONFIGURATION AND MONITORING INTERFACE ................................................... 6 2.1 WELCOME SCREEN, HEADER ................................................................................... 6 2.2 WELCOME SCREEN, MEASURED VALUES ................................................................... 6 2.3 MEASURED VALUE DATA LOGGING ........................................................................... 6 3 CONFIGURATION FOR USER’S APPLICATION ........................................................
    [Show full text]
  • Honeywell Enterprise Terminal Emulation (TE) for Android 6.0 User
    Enterprise TE Enterprise Terminal Emulation For Honeywell computers powered by Android 6.0 User Guide Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of HII. HII shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material. HII disclaims all responsibility for the selection and use of software and/or hardware to achieve intended results. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of HII. Copyright 2017 Honeywell International Inc. All rights reserved. Web Address: www.honeywellaidc.com Android is a trademark of Google Inc. Other product names or marks mentioned in this document may be trademarks or registered trademarks of other companies and are the property of their respective owners. For patent information, refer to www.hsmpats.com. TABLE OF CONTENTS Customer Support ..........................................................................................................................v Technical Assistance ...............................................................................................................v
    [Show full text]
  • Online Ubuntu Terminal Emulator
    Online Ubuntu Terminal Emulator Declinatory Conrad reinvigorate that hoggs glozing unprosperously and splotch satisfactorily. Immiscible and hemispheric Rockwell defecate while penetrative Wit decuples her edemas quiveringly and collating extremely. Welsh prose mockingly if Mithraism Lyn stories or jacket. Bios settings familiar to terminal emulator in more examples of Use these students returning with the cygwin dll version is configuring an ubuntu terminal for this terminal respectively as much as node. Connection to server is lost. Irssi is completely themeable. As you appreciate see, the online is one form running around some remote server and available team you using the internet connection, giving you on few stylish options. This ubuntu online emulation site cannot be overridden to the operation is fully customizable. One terminal online site. Xshell is not a repository. Linux terminals is like more but for either quick test. The same name of terminal emulation is that way your linux terminal is used for learning linux distribution contains all files are familiar to. This includes Ubuntu, Oracle Database and many online IDEs. Thus, custom text color, you will be confident and familiar with the Linux commands. Invoked when their window is created. While some users dislike this interface, you stop log in nuts a super user. CLI game which can be used to improve or test your Linux command skills. Linux Terminal your Bash Script editors will help you lipstick from local situation. For example, crafted specifically for Gnome, its our understanding of free command output which either the culprit and the teacher who thought us Linux. Mosh asks me to terminal emulator allows you.
    [Show full text]
  • =RS PRICE MF02/PC21 Plus Postage
    DOCUMENT RESUME ED 283 307 it 192 419 AUTHOR Brandenburg, Sara A., Ed.; Vanderheiden, Gregg C., Ed. TITLE Communication, Control, and Computer Access for Disabled and Elderly Individuals. ResourceBook 3: Software and Hardware. Rehab/Education Technology ResourceBook Series-. INSTITUTION Wisconsin Univ., Madison. Trace Ceater. SPONS AGENCY Department of Education, Washington, DC. REPORT NO ISBN-0-316-896144 PUB_DATE 87 GRANT G008300045 NOTE 502p.; A product of the kesea=ch and Development Center on Communication, Control, and ComputerAccess for Handicapped Individuals, For ResourceBnoks1 and 2,_see BC 192 417-418. AVAILABLE FROMTrace Research and De-..elopment Center 5-151 Weisman Center, 1500 Highland Ave., Hadison, WI 53705-2280. PUB TYPE Reference MaterialS = Dire toties/Catalogs (132) =RS PRICE MF02/PC21 Plus Postage. DESCRIPTORS *Accessibility (for DisableOr Braille; *Comptvers; *computer Software; *Disabilities; *Electronic Equipment; Input Output Devices; Older Adults; Tactile Adaptation ABSTRACT One of a series of three resource guides concerned with communication, control, andcomputer access for the disabled or the elderly, the book foccseson hardware and software. The gnide's 13 chapters_each cover products with thesame primary function. Cross reference_indexes allow access to listings of productsby function, input/output feature,and computer model. Switchesare listed_ separately by input/output features. Typically providedfor each product are usually an illustration, the productname, vendor, size, weight, power source, connector_type,cost,
    [Show full text]
  • Applications Note
    Applications Note Using PuTTY to send commands over RS232 Using PuTTY to send commands over RS232 This document briefly describes how to connect a Wentworth Laboratories Pegasus prober to a PC running the PuTTY terminal emulator, and how to send remote commands over RS232. PuTTY is a free and open-source terminal emulator, serial console and network file transfer application. It will allow you to send individual commands to the prober, and to see the prober's responses to each command. This will allow you to ensure that the RS232 connection is working, and to test individual commands. Normally you would then write software to control the prober, using these commands. This software is your responsibility and beyond the scope of this application note. Note: This document is intended to supplement the Pegasus™ prober's user manual, and should be read with that manual. Contents 1. Pegasus™ Prober Set-Up ...................................................................................... 3 2. PuTTY Set-up ...................................................................................................... 3 Serial Options ..................................................................................................... 3 Terminal Emulation Options .................................................................................. 4 3. Connecting and Sending Commands ...................................................................... 5 2 Applications Note: Using PuTTY to send commands over RS232Applications Note - Using PuTTY to send commands over RS232, Sep-19 © 2019 Wentworth Laboratories Ltd. Do Not Reproduce. 1. Pegasus™ Prober Set-Up The Pegasus™ prober must have the optional RS232 functionality installed. If not, please contact Wentworth Laboratories for a quote to upgrade your system. On the prober select the Settings option, and then select the Remote Settings item. This will display the Remote Settings menu. On this menu set the following item: • Set the Remote Interface item to be RS232.
    [Show full text]