Measurement Guide

Total Page：16

File Type：pdf, Size：1020Kb

TM MEASUREMENT GUIDE HOW TO MEASURE TERMINOLOGY: FRONT OF A GARMENT BACK MEASUREMENTS High Shoulder Point (HSP): at the neck it is the Back Length: measure from HSP to hem. highest point. Center Back Length: measure from center back neck Front Length: from high shoulder point to hem. to hem. Center Front Length: from center front neck to hem. Across Shoulders: measure on back straight from shoulder armhole to armhole at top edge. Shoulder slope: from the HSP line to shoulder at arm hole. Across Back: measure 5” below HSP armhole to armhole. Across Front: measured 5” below HSP from arm hole seam to seam. Neck Width: measured on back between HSP straight. Bust: measured 1” below arm hole. Back Neck Drop: measured from HSP to neck seam. Hem- Sweep: measured at bottom edge straight PANTS across. Waist: measured 16.5” below high shoulder point Hem Curve: measured following hem curved edge. Across Front: measured 5” below HSP from arm hole seam to seam. Sleeve Cap Height: measured from top sleeve at shoulder to underarm level. High Hip: measured 3” below waist. (3 pt measure). Sleeve Length: short and 3/4 measure sleeve to hem. Low Hip: measured 5” below HSP from arm hole seam to Long measure include cuff. seam. (3 pt measure). Bicep: measured 1” below underarm seam. Front / Back Rises: measure along seams. Elbow: measured midway between bicep and sleeve RAGLAN STYLE hem (8.5” below underarm). Across Front: 5” below HSP. Cuff / Rib Depth: measured relaxed / button closed Front / Back Raglan Seam: measured followed on seam from neck seam to underarm seam. Arm Hole Straight: measured on diagonal from sleeve top to underarm sleeve. Overarm: measured from neck seam followed along mid arm to sleeve hem. Front Neck Drop: Measured from HSP to center front neck seam or to 1st mid button. DOLMAN STYLE Bust: measure 12” below HSP. COLLAR 1/2 Neck Circumference: measure with stand button, Front / Back: measure 5” below HSP from sleeve hem closed and straight across through center. to sleeve hem. Collar Point: measure length from neck seam to point. Armhole Depth: measure from HSP to armhole level. BODY MEASUREMENT CHART (FULLBODY MMTS MEASUREMENT IN INCHES) CHART (FULL MMTS IN INCHES) WOMENS WOMENS PLUS USA & CANADA SIZE 6 8 10 12 14 16 18 20 22 24 26 S M L L XLXL XXL S M L L RELATIVE SIZES SM LXL XXL XXXL OS BUST 35 1/4 36 1/4 37 1/4 38 3/4 40 1/4 42 1/4 44 1/4 47 49 51 WAIST 27 28 29 30 3/4 32 1/2 34 1/2 36 1/2 40 42 44 LOW HIP 38 1/4 39 1/4 40 1/4 41 3/4 43 1/4 45 1/4 47 1/4 50 52 54.

Copy Link

Recommended publications

Convertible Collar Construction
Convertible Collar Construction Directory Click any image to go to that section Yoke/Facing Options: Intro and Gallery By far the most common set-up for a The purpose of this introductory section is to convertible-collar shirt is that it has front facings feature and compare the range of other options and a yoke, and that these two details don’t touch, also, if less commonly, in use beyond this classic as in the example at right. one, before I proceed to work step-by-step through a handful of useful variants . Many other possible That is, the facings don’t extend far enough combinations, and of course, variations on the towards the shoulders at the neckline that they’ll ones here, are conceiveable and may suit your meet with or join to the fronts of the yoke layers. As project better, so feel free to experiment. a result, the yoke construction steps aren’t integrated into the collar steps and are completed, in front at least, before the collar is begun, so the options for using the yoke as a back facing are eliminated. The steps for this classic arrangement are described below in Variation #5, in the Front Facing Only category. Collar Insertion Options Step-By-Step No Yoke or Facings Required Front facings Only Front and Back Facings, or Yoke Used as Facing Variation 1: Collar Applied as Band Variation 3: Collar’s Back Neckline Edge-Stitched Variation 6: Back Facings 1 3 and Facings Secured at Shoulder Seams 6 Options: Options: 1. Edge-stitched neckline 2.
[Show full text]
Taking Your Measurements \ I / \ I / ' ------/ / ' ,,,__
• 1mp s __ ...,... ___ _. _____ ___ ,,. -, Bulletin 498 / January 1956 / ' : TAKING YOUR MEASUREMENTS \ I / \ I / ' ------ / / ' ,,,__..... --- ------- ./ _,."' / / --- --- 1 -------------- \ \ ' A good looking dress is a well-fitted dress. Achieving a good fit depends upon three things: knowing your own figure measurements, selecting the size and type pattern which most nearly corres ponds to your measurements, and then making any necessary alterations in the pattern before cutting your dress. This leaflet tells you how to take your measurements and provides a place for you to record them. What Is A Well-fitted Dress? A dress that fits you well adapts itself to your body. Ir brings out your good points and skillfully hides your poor ones. You will know a good fit by- Direction of grain of fabric. - Crosswise yarns are parallel to the floor at the center-front and back busdine, and at the hipline, unless the dress has unusual style details. lengthwise yarns are at right angles to the floor at the center-front and back of both skirt and bodice of a dress. lengthwise yarns on the sleeve cap lie in the direction of the arm when it hangs straight at the side . This varies slightly on different figures but in general the crosswise yarns are also parallel are straight in front and back of your arm except to the floor. when special style features, such as extended shoul Direction of seam lines. - Seam lines that ders, requir.e otherwise. lie and hang straight keep your dress in proper li~e The waistline seam appears to be straight around on your figure.
[Show full text]
Clothing, Conformity, and White-Collar Masculinity, by Erynn Masi De Casanova Trenton M
University of Nebraska - Lincoln DigitalCommons@University of Nebraska - Lincoln Sociology Department, Faculty Publications Sociology, Department of Spring 2016 Review of Buttoned Up: Clothing, Conformity, and White-Collar Masculinity, by Erynn Masi de Casanova Trenton M. Haltom University of Nebraska-Lincoln, [email protected] Follow this and additional works at: http://digitalcommons.unl.edu/sociologyfacpub Part of the Family, Life Course, and Society Commons, and the Social Psychology and Interaction Commons Haltom, Trenton M., "Review of Buttoned Up: Clothing, Conformity, and White-Collar Masculinity, by Erynn Masi de Casanova" (2016). Sociology Department, Faculty Publications. 559. http://digitalcommons.unl.edu/sociologyfacpub/559 This Article is brought to you for free and open access by the Sociology, Department of at DigitalCommons@University of Nebraska - Lincoln. It has been accepted for inclusion in Sociology Department, Faculty Publications by an authorized administrator of DigitalCommons@University of Nebraska - Lincoln. CULTURE , S OCIETY & M ASCULINITIES 8(1) ■ 91 Buttoned Up: Clothing, Conformity, and White-Collar Masculinity , by Erynn Masi de Casanova. Ithaca: ILR/Cornell University Press, 2015. 275 pp. ISBN 978-0- 8014-5418-9 (hb) 978-1-5017-0049-1 (pb) Erynn Masi de Casanova’s Buttoned Up: Clothing, Conformity, and White-Collar Mas - culinity (2015) draws on white-collar men’s discussion of their fashion choices to shed light on how masculinity, work-type, class, race, and geographic region shape their styles of dress. Each chapter highlights a piece of what goes on in men’s heads as they dress for work: workplace dress codes (both official and unofficial), family inspiration, for whom they dress, and the pitfalls of being too fashionable or not trendy enough.
[Show full text]
ALDI Textiles
ALDI Textiles ALDI Textiles Guideline 2 Aloe Vera. Recognises the demand all on its own. A Aloe vera micro capsules are attached to the textile fibres using a binder. The friction from wearing causes the microcapsules to burst and release the moisturising substance. The advantage of the microcapsules is the fact that the encapsulated substance is only released when the fabric is mechanically stressed. Through the addition of the aloe vera capsules, the garment hydrates and moisturises the skin. Anti-Pilling. Reduces pilling. A Anti-pilling is a special finishing process for reducing the formation of pilling, meaning lint, in predominantly synthetic materials. This is primarily achieved through a mechanical process or heat treatment. ALDI Textiles Guideline 3 Breathable. Keeps you dry and keeps moisture away. B Breathable fabrics are defined as textiles which possess certain physiological properties which above all wick moisture away from the skin. Such materials may also be water-resistant and therefore protect against rain. See also: Cool & Fresh, COOLMAX® ALDI Textiles Guideline 4 Cotton. The all-rounder among textiles. C Cotton is derived from the soft seed hair of the cotton plant. The plant thrives in countries with a sub-tropical climate, such as the USA, Egypt, India, and South Africa, and in terms of volume is one of the most important raw textiles materials in the world. The quality of cotton wool is dependent on its fineness, strength, fibre length and consistency. See also: Wool, virgin wool, organic cotton, Pima cotton PROPERTIES: It is skin-friendly: Due to its softness, it is very pleasant on the skin.
[Show full text]
Dressing Aids F Are Available Through Specialtyretailers
The War Amps For Your Information Tel.: 1 877 622-2472 Fax: 1 855 860-5595 [email protected] Dressing Aids rom buttons, buckles, zippers and laces, these Fsimple fasteners can pose difficulties in an amputee’s daily activities. Featured below are various Velcro tabs dressing aids that can make many of these tasks easier. Some can be made using household items and others are available through specialty retailers. Hassle-free Fasteners • Velcro tabs under shirt or blouse buttons instead of conventional button holes. • A Velcro strip instead of a zipper in the fly of trousers. • Velcro on jacket cuffs. • Toggle buttons on outer wear which are easier to manage than stiff, flat buttons. Elastic cufflink • Cuff links made of elastic thread between two buttons keep cuffs looking tidy while letting you slide your hand in and out without undoing the button. • Some button-up shirts can be put on without being fully unbuttoned, simply leave enough buttons undone to allow room for your head, and then A C fasten the rest later. B D Button Hooks To assist the amputee with buttoning clothing, various button hooks are available including the regular handle(A), rubber handle(B), cuff handle(C), and ball or knob handle(D). Prosthetic Limbs and Devices Prosthetic A button hook has a small wire loop that slips over the button and when pulled, guides the button through the buttonhole. Zipper Pull Rings For those who have difficulty holding onto and pulling the regular zipper tabs, a variety of zipper pull rings are available which attach to the regular zipper tab and which can be grasped more easily by artificial limbs.
[Show full text]
Sewing Technique: Lock Stitch (Hem 1”)
Sewing Technique: Lock Stitch (Hem 1”) The lock stitch is a hand stitch used for hemming purposes. It gives a secure hold with limited view of the thread on the outer side of the garment. STEP 1: Stay stitch ¼-inch from the fabric edge. (A stay stitch is a single line that is used for guidance and to keep the fabric from fraying. It is a normal stitch length and backstitching is a personal preference.) STEP 2: Fold the hem edge back 1-inch. Press fold in order to make a crease in the fabric. Press fabric 1 again ¼-inch. This press will follow the stay stitch seam. STEP 3: Secure thread to the folded edge of fabric on stay stitch line in order to hide the knot. STEP 4: Moving left, make a small stitch (1/2 to ¾ inch). The stitch should first go through the ¼-inch fold; then a small stitch is made that only goes through the outside layer of the garment. Pull thread gently back through to the inside of the garment. Avoid pulling the thread tight as the needle passes back through the loop created from the stitch. 5 3 5 STEP 6: To tighten lock stitch, pull thread to the left. STEP 7: Continue moving left and repeating step 5 until seam is complete. STEP 8: Once finished, secure thread to prevent it from unraveling. NOTE: The lock stitch can be used in place of a catch stitch. 7 6 Industry Standards for a Well-Constructed Hem: • Hem is level • Hem lies flat • No puckers, twists, or extra bulk • Hand stitching is not visible on correct side of garment • Hand stitches are evenly spaced • Topstitching is even and parallel to hemline References: Readers Digest.
[Show full text]
Tailoring Series TECHNIQUES for TAILORING UNDERLINING a TAILORED GARMENT—Underlining Is a Second Layer of Fabric. It Is Cut By
tailoring series TECHNIQUES FOR TAILORING UNDERLINING A TAILORED GARMENT—Underlining is a second layer of fabric. It is cut by the garment pattern pieces and staystitched to the wrong side of the corresponding outer sections before any seams are joined. The two layers are then handled as one. As a general guide, most suit jackets and coats look more pro- fessional when underlined. Underlining is especially recommended for lightweight wool materials, loosely woven materials and light- colored materials. For additional information on selecting fabrics for underlining and applying the underlining, see Lining a Shirt 01' Dress HE 72, N. C. Agricultural Extension Service. STAYSTITCHING—Staystitch all outer garment pieces before construction begins. If garment is underlined, stays-titching is done when the two layers of fabric are sewn together. Staystitch 1/3 in. outside seamline (on the seam allowance). Stay- stitch “ with matching cotton thread on all curved *areas that may stretch during construction such as necklines, side seams, shoulder seams, armholes, and side seams of skirt. Use directional stitching always to prevent stretching of fabric and to prevent one layer of fabric from riding. The direction to stitch is indicated by small arrows on the pattern on the seamlines. INTERFACINGS—Select a high quality hair canvas for the front and collar of coats and jackets. The percentage of wool indicates the quality—the higher the wool content of the canvas the better the quality. Since a high percentage of wool makes the hair canvas fairly dark in color, it cannot be used successfully under light-colored fabrics. In these cases use an interfacing lighter in color and lower in wool content.
[Show full text]
Sewing & Hand Application
APPLICATION MANUAL Sewing & hand application Sewing and hand application Preciosa Components offers a wide range of various products ideal for sewing and embroidery. Thanks to a rich choice of shapes, sizes, settings and applications, Preciosa crystals can be used in mass apparel and accessories production, designer´s studios and Do-It-Yourself activities. Stones can be easily applied with industrial sewing or embroidery machines or household sewing machines and are also suitable for various manual applications. PRODUCT OVERVIEW COMPONENTS SEWING HAND APPLICATION Flat Back Stones Sew-on Stones Beads and Pendants Beads Pendants Nacre Pearls Nacre Pearls Cup Chains Plastic Bandings Fashion and Fashion Jewelry Components Metal Bandings Stones in Settings Fashion and Fashion Crystal Mesh Jewelry Application MACHINES, TOOLS AND AIDS Use the following machines, tools and aids for sewing Preciosa components: • Household sewing machine with common stitch types (straight, zigzag, button sewing programme). • Industrial sewing machine. • Sewing machine accessories – presser feet, needles, threads. • Goggles. Household sewing machine Industrial sewing machine Different types of presser feet 2 PRECIOSA CRYSTAL COMPONENTS APPLICATION MANUAL 3 Sewing – basic rules TYPES OF MACHINE APPLICATION OF CRYSTAL COMPONENTS CHOICE OF THE RIGHT THREAD APPLICATION MACHINE TOOL PROGRAMME NOTE Synthetic threads of 50 – 60 Nm strength are the most suitable for sewing Preciosa stones. The threads Programme for button Switch off the lower Sewing are
[Show full text]
Placket Construction Options
Placket Construction Options 1 Type1: Two Separate Bound Edges on a rectangular stitching box The key to this structure is that the bindings are initially stitched only to the seam allowances on each side, and NOT stitched across the end, of the clipped box, which means that they, and the clipped triangle at the bottom, remain loose and can be arranged before the nal nishing to go on either side of the fabric, as well as either over or under the other, after joining them at the sides. The widths and lengths of the bindings and the space between the sides of the clipped box determine all the other options available in this most exible of all the placket types I know of. Variation 1: Both bindings t inside the stitching box If you cut the bindings so the nished, folded widths of both are equal to or smaller than the space between the initial stitching lines, as shown above, you can arrange both ends at the clipped corners to all go on one side of the fabric (right or wrong side), along with the clipped triangle on the garment. You’ll get the best results if the underlapping binding is slightly smaller than the overlapping one. This can be man- aged by taking slightly deeper seam allowances when you join this piece, so they can initially be cut from the same strip. Or, you can place one end on each side with the Both ends on RS One end on RS, Both ends on WS triangle sandwiched in between.
[Show full text]
Price List Best Cleaners 03-18.Xlsx
Price List Pants, Skirts & Suits Shirts & Blouses Pants Plain…………………………………………… 10.20 Business Shirt Laundered and Machine Pants, Silk/Linen…………………………………… . 12.30 Pressed (Men’s & Women’s)…… 3.60 Pants, Rayon/Velvet………………………………… 11.80 Pants Shorts………………………………………. 10.20 Chamois Shirt…………………………………………… 5.35 Skirts, Plain………………………………………… . 10.20 Lab Smock, Karate Top………………………………… . 7.30 Skirts, Silk, Linen………………………………….. 12.30 Polo, Flannel Shirt……………………………………… .. 5.35 Skirts, Rayon Velvet……………………………… .. 11.80 Sweat Shirt……………………………………………… . 5.70 Skirts Fully Pleated………………………………. 20.95 T-Shirt…………………………………………………… .. 4.60 Skirts Accordion Pleated………………………… . 20.95 Tuxedo Shirt……………………………………………… . 6.10 Suit 2 pc. (Pants or Skirt and Blazer)……………… 22.40.. Wool Shirt………………………………………………… . 5.35 Suit 3 pc. (Pants or Skirt Blazer & Vest)……………… 27.75. Suit, body suit………………………………………… 10.60. Blouse/Shirt, Cotton, Poly…………………………………… 9.50.. Suit, Jumpsuit…………………………………… 25.10 Blouse/Shirt, Rayon, Velvet………………………………… 11.10.. Sport Jacket, Blazer……………………………… .. 12.20 Blouse/Shirt, Silk, Linen……………………………………… 11.60 Tuxedo……………………………………………… . 22.95 Blouse/Shirt, Sleeveless……………………………………… 7.80 Vest………………………………………………… . 5.35 Dresses Outerwear Dress, Plain, Cotton, Wool, Poly, Terry, Denim…….. 19.00 Blazer, Sport Jacket……………………………… . 12.20 Dress,Silk, Linen …….………………………………. 23.20 Bomber Jacket………………………………….. 16.20 Dress,Rayon,Velvet …………………………………. 22.20 Canvas Field Coat………………………………… 16.20 Dress, 2-Piece, Dress & Sleeveless Jkt……………………… 27.60 Canvas Barn Jacket………………………………
[Show full text]
Drafting Collars
DRAFTING COLLARS Excerpted from GERTIE’S NEW BOOK FOR BETTER SEWING GERTIE’S NEW BOOK FOR BETTER SEWING A MODERN GUIDE TO COUTURE-STYLE SEWING USING BasIC VINTagE TECHNIQUES GRETCHEN HIRSCH Photographs by Jody Rogac Illustrations by Sun Young Park Available wherever books are sold. find out more at melaniefalickbooks.com Copyright © Gertie's New Book for Better Sewing by Gretchen Hirsch, published by STC Craft | Melanie Falick Books, an imprint of ABRAMS, 2012. DRAFTING COLLARS ADJUSTMENT FOR PETER PAN COLLAR Collars can also be drafted from scratch and added to your blouse and dress patterns. My favorite vintage-style collar is the Peter Pan collar, which I incorporated into the blouse variation on page 160. It can be added to any blouse, jacket, or dress with a round neckline, and it will make the most basic garment ooze charm! Depending on how you style a Peter Pan collar, it can look ladylike or playful, 1930s glam or 1960s mod. Once you understand the basics of making a Peter Pan collar, you can apply this knowledge to any shape or size collar you like. For the purpose A. Overlap shoulder seams. of this little design project, let’s use a 1940s button-back blouse as our base. The basic premise of drafting a collar like this is that you use the neckline of your garment as your guide—the basic shape of your collar is right there! So start by laying out your blouse front and back pattern pieces on a table. Use a colored pencil to draw in the neckline and shoulder seam lines on your pattern pieces.
[Show full text]
'L::C Make a Gathered Skirt
H7l.f -·'1~ 'l::c Make A Gathered Skirt CIRCULAR 580 OCTOBER 1964 AGRICULTURAL EXTENSION SERVICE VIRGINIA POLYTECHNIC INSTITUTE BLACKSBURG, VIRGINIA Make a Gathered Skirt Prepared by MarrJaret Groseclose, Err:tension ClothinrJ Specialist •Many girls like gathered skirts and they Make a Placket • are easy to make. Plump girls look best in 1. Work with the side seam where the gored skirts. When you make a gathered opening was left for the placket. skirt, you learn to make seams, put in a 2. Fold back the front placket extension placket, fit a waistband, hem a skirt, and put to the seam line. Press and pin. on a fastener. You study what to look for in 3. Machine stitch the length of the placket choosing a fabric and how to prepare it for opening 5/ 8" from the folded edge. Stitch cutting a garment. This will help you in diagonally to the folded edge (or seam line), making other garments. catching the back extension. 4. Clip the back seam allowance almost Supplies You Will Need to the stitching line, approximately 1/2" be- low the end of the placket. Include a sewing box, thread to match 5. Press the side seams open. background of fabric, hooks and straight eyes, 6. Two snap fasteners may be used to i:maps, and fabric. The amount of fabric keep the placket closed. needed will be twice the length of your skirt, including 3" for hem plus 5" for waistband. Figure 2 Measure and Cut 1. Straighten the fabric. 2. If you are using 2 lengths for the skirt, cut a 5-1/8" strip across the fabric for the band.
[Show full text]