TRACEABLE® JUMBO-DIGIT STOPWATCH INSTRUCTIONS

SPECIFICATIONS for quick advance. Pressing “START/STOP” do not change. If the is Display: ½″ 6-digit LCD repeatedly causes the to advance in a running, indicated by the rapid advance- Range: 23 hr, 59 min, 59 sec pre-programmed sequence of AM, PM, and 24 ment of seconds, press “START/STOP” to stop it. Resolution: 1 sec (military) , denoted by “A”, “P”, or “H” on the display. Advance hours until the 2. Press “RESET” to reset display to all Accuracy: 0.001% desired format is achieved. zeros. Alarm: Time-of- alarm, Daily alarm 6. Set and day by pressing “RESET” until B. Continuous Timing with snooze, Hourly chime month and day appear and day begins flash- If timer reaches maximum upper limit, it will 7 Size/Weight: 3 x 2½ x /8″ / 2½ oz ing, then press “START/STOP” to advance roll over to zero and continue counting up. Features: Single action, time-out, cumulative day. Press and hold “START/STOP” for quick C. Time-in/Time-out Timing split and continuous timing • Timing resolution advance. If a pause in the timing operation is required to 1/100 seconds, for the first 30 • 7. Set the month by pressing “RESET” until press the START/STOP button to “freeze” the Continuous timing to 23 hrs, 59 min and 59 sec month begins flashing, then press “START/ display at the current reading (time-out). To STOP” to advance the month. Press and hold resume time at the point it was stopped • Time-of-day display in hrs/min/sec, AM/PM, “START/STOP” for quick advance. press the START/STOP button again. An , and weekday • Choice of 12/24 hour 8. Set the day by pressing “RESET” until unlimited number of timeouts may be taken. display • Water resistant • O-ring sealed • the bar at the top of the display flashes, then D Lap/Split Timing Shock-resistant • ABS plastic case • Non-slip press “START/STOP” to position the flashing Lap/Split timing freezes the display for partial rubber sides bar under the correct day. Press and hold while the internal clock continues “START/STOP” for quick advance. to run. CONTROLS 9. Press “MODE” to return to normal time. 1. Press “MODE” to enter stopwatch mode. A. MODE Button - Each press of MODE button 10.Press and hold “START/STOP” to view current This mode is indicated by a display of displays modes in the following sequence: date. time in which seconds do not change. If Clock, Stopwatch, Alarm Setting and Time C. Alarm Operations the timer is running, indicated by the Setting. 1. To set the alarm time: rapid advancement of seconds, press B. START/STOP Button – has the following a. Press “MODE” until hours begin flashing, “START/STOP” to stop it. functions in each of the modes listed below: then press “START/STOP” to advance 2. Press “RESET” to reset display to all 1. Clock mode - switches display from time hours. Press and hold “START/STOP” for zeros. of day to date quick advance. 3. Press “START/STOP” to start the timer. 2. Stopwatch mode – starts and stops c. To set minutes, press “RESET” until minutes 4. Pressing “LAP/SPLIT” will display the timer begin flashing then press “START/STOP” to elapsed time since the timer was 3. Alarm Setting mode – advances day, advance minutes. Press and hold “START/ activated, as with timing an event. hour and STOP” for quick advance. Pressing “LAP/SPLIT” again will return 4. Time Setting mode – advances day, hour d. The alarm time should now be set. Press the display to the running timer. This and minute “MODE” to return to normal time display. step may be repeated as many times as C. RESET, LAP/SPLIT Button – has the 2. To view alarm time: required, as in timing multiple events. following functions in each of the modes a. Return the display to clock mode. The timer continues to run until “START/ listed below: b. Press and hold “RESET”. STOP” is pressed to stop it. 1. Clock mode: switches display from time 3. To remove alarm time: of day to alarm time a. Return the display to clock mode. ALL OPERATIONAL DIFFICULTIES 2. Stopwatch mode – resets the timer to b. Press “RESET” and “START/STOP” If this unit does not function properly for any zero, stops and starts time-in/time-out together to switch the alarm function on reason, replace the battery with a new high- and lap/split timing. and off. The alarm icon in the upper right quality battery (see “Battery Replacement” 3. Alarm Setting mode – selects hour or corner illuminates to indicate the alarm section). Low battery power can occasionally minute display to set alarm time function is on. cause any number of “apparent” operational 4. Time Setting mode – advances through 4. To activate the hourly chime function: difficulties. Replacing the battery with a new display for time and date settings a. Press and hold “RESET”. fresh battery will solve most difficulties. D. MODE – same functions as “A” button b. With “RESET” depressed, press “MODE” above. Location at lower right side of unit to turn the hourly chime function on and BATTERY REPLACEMENT for ease of operation. off. A row of bars across the top of the Erratic readings, a faint display, no display or a ATTACHMENTS display indicates the hourly chime function flashing display are all indicators that the battery Detachable clip, mounting Velcro and 42” is activated. must be replaced. To replace the battery, lanyard. 5. To activate the snooze function: remove the screws on the back of the unit. a. With alarm sounding, press “START/STOP” Remove the back cover, taking case to avoid OPERATION once to put the stopwatch into snooze dislodging parts inside. Unscrew and remove the Clock Operation mode. The alarm will sound every 5 battery cover. Replace the exhausted battery A. Entering Timing Modes minutes while in snooze mode. with a new 3 volt lithium battery. Replace the 1. To enter and change timing modes: b. Press “RESET” once to exit snooze mode. battery cover. Replace the back cover, replace Scroll through the modes by pressing the screws and tighten securely. Replacement “MODE” repeatedly. Stopwatch Operation battery Cat. No. 1005. 2. Mode Sequence: When scrolling, the A. Single-Action Timing modes appear in the following sequence: 1. Press “MODE” to enter stopwatch mode. This WARRANTY, SERVICE, OR RECALIBRATION Clock, Stopwatch, Alarm Setting and mode is indicated by a display of time in which Time Setting. B. Setting Time-of-Day and Date 1. Set the display to clock mode. 2. Press “MODE” repeatedly until the seconds start to flash. 3. Set seconds to zero by pressing “START/ STOP”. At this point, pressing “RESET” repeatedly scrolls through a pre- programmed sequence for setting, in the following order: Seconds, minutes, hours, day, month and day of week. 4. Set minutes by pressing “RESET” until minutes begin flashing, then press Cat. No. 1051 “START/STOP” to advance minutes. Press and hold “START/STOP” for quick Traceable® Jumbo-Digit Stopwatch Instructions advance. 92-1051-00 5. Set hours by pressing “RESET” Rev 2 062105 repeatedly until hours begin flashing, then press “START/STOP” to advance hours. Press and hold “START/STOP” © 2005