Congratulations on Owning Your New Nautica Watch

Home , Stopwatch, Watch

CONGRATULATIONS ON OWNING YOUR NEW NAUTICA WATCH DEVELOPED FROM ADVANCED ELECTRONICS TECHNOLOGY, THE MOVEMENT IS MANUFACTURED FROM THE BEST QUALITY COMPONENTS AND POWERED BY A LONG LIFE BATTERY. NAUTICA watches have been developed with the highest attention to quality, function and detail, as befits the NAUTICA tradition. Please read the following instructions carefully to fully understand all of the functions of your finely crafted timepiece.

WATER-RESISTANCE If your watch is water-resistant, it will be indicated on the watch face or on the caseback. • 50 Meter Water-Resistant watch withstands water pressure to 86p.s. i.a. (equals immersion to 164 feet or 50 meters below sea level) and dust as long as crystal, crown and case remain intact. • 100 Meter Water-Resistant watch withstands water pressure to 160p. s.i.a. (equals immersion to 328 feet or 100 meters below sea level) and dust as long as crystal, crown and case remain intact. • 200 Meter Water-Resistant watch withstands water pressure to 320p. s.i.a. (equals immersion to 656 feet or 200 meters below sea level) and dust as long as crystal, crown and case remain intact. NOTE: CROWN MUST BE SCREWED INTO THE CASE PROTRUSION TO ASSURE WATER RESISTANCE. INDIGLO® NIGHT-LIGHT If your watch has “INDIGLO” on the dial, your watch is equipped with the INDIGLO Night-Light. To activate this feature, depress the crown or the pusher on the left side of the watch to illuminate the entire dial for easy reading during nighttime or low light conditions. Light will appear immediately. Your NAUTICA watch featuring INDIGLO Night-Light contains a patented electroluminescent technology (U.S. Patent Number 4,527, 96 and 4,775,964). The INDIGLO Night-Light illuminates the entire watch lens with a uniform bright light that offers superior readability in all low light and nighttime conditions. Simply press the appropriate button to activate. WARNING: DO NOT PRESS THE BUTTON UNDER WATER AS THE WATCH WILL NOT RETAIN WATER RESISTANCE. INDIGLO is a registered trademark of Indiglo Corporation.

BATTERY Battery contains small amount of mercury. Please recycle or dispose of properly. SCREW-IN SETTING CROWN

ATTENTION This is a screw down crown Do not pull Please read instruction booklet before operation

SCREW-IN SETTING CROWN STICKER

Some deep-depth water-resistant watches require the setting crown to be screwed in to ensure water-resistant. If your Nautica watch has a transparent sticker at back of the case back (diagram above) please unscrew the crown before setting your watch, and the crown must be screwed in after setting the watch.

To screw in, push in the crown firmly against the thread protrusion and hold it in while turning the crown clockwise. Continue to screw in the crown light until it is tight . ELAPSED TIME RING If your watch is equipped with a rotatable outer dial with numbers and indicators, this Elapsed Time Ring may be used to indicate the length of time remaining for an activity or the starting time of an activity. TIME REMAINING - set the outer ring so that the traingle is pointing to the time the activity is to end. STARTING TIME - set the triangle on the time the activity is to begin. TACHYMETER A tachymeter measures the speed at which the wearer has traveled over a measured distance, i.e., a measured mile on the highway. For example, start the chronograph when you pass the starting point and stop it when you pass the finish. You can then read your speed in units per hour off the tachymeter scale. BAND ADJUSTMENT To disconnect band from clasp, press in end of spring bar (use pin or small paper clip) and separate link band from clasp as illustrated. To reassemble band to clasp, place spring bar in band and place end of spring bar into desired hole in clasp. Press opposite end of spring bar in and slide into clasp and position so tip snaps into corresponding hole. CHRONOGRAPH MODELS

STOPWATCH 1/20SEC. HAND

PUSHER “A” SMALL SECOND HAND CROWN POSITION

A B C STOPWATCH SECOND HAND PUSHER “B”

STOPWATCH HOUR HAND STOPWATCH MINUTES HAND YM92

Note: Crown position “A” & “B” Note: Pusher “A” (Top Right), “B” (Bottom Right) Note: 12 O’clock eye “STOPWATCH 1/20 SEC elapsed” Note: 9 O’clock eye “SEC elapsed” Note: 6 O’clock eye “STOPWATCH HOUR/MIN elapsed”

This Chronograph watch has 3 functions: TIME CALENDAR STOPWATCH

11 TIME To set the time: 1. Pull crown to position “C” 2. Turn crown clockwise / counter clockwise to correct time 3. Push crown to position “A”

CALENDAR To set the calendar: 1. Pull crown to position “B” 2. Turn crown clockwise to correct calendar 3. Push crown to position “A”

STOPWATCH The stopwatch is capable of measuring: – 1/20 seconds elapsed up to one second (top eye) – Minutes elapsed up to 30 minutes (bottom eye) – Hour elapsed up to 12 hours (bottom eye) – Seconds elapsed up to one minute (middle eye)

Before using the stopwatch, reset the stopwatch hands To the “12” and “0” position.

STANDARD STOPWATCH MEASUREMENT: 1. Press pusher “A” to start timing 2. Press pusher “A” to stop timing 3. Press pusher “B” to reset

12 ACCUMULATED ELAPSED TIME MEASUREMENT: 1. Press pusher “A” to start timing 2. Press pusher “A” to stop timing 3. Press pusher “A” to restart timing 4. Press pusher “A” to stop 2nd timing 5. Press pusher “B” to reset

Example of using split time measurement for two runners Two runners can be timed simultaneously; the first runner’s time can be recorded while the second runner’s time will continue to be accumulated until he finishes.

SPLIT TIME MEASUREMENT: 1. Press pusher “A” to start the timing of the first runner 2. Press pusher “B” to stop and record the timing of the first runner. (Once pusher B is activated, even though the stopwatch 1/20 sec. hand and the big stopwatch sec. hand stop on the dial, the stopwatch still continues to time internally.) 3. Press pusher “B” to start the timing of the second runner. The stopwatch sec. hand will jump to show internal accumulated time and to carry on timing of the second runner. 4. Press pusher “A” to stop the timing of the second runner and record the time 5. Press pusher “B” for third time to reset, all stop watch hands will return to 12 o’clock position.

13 TO ADJUST STOPWATCH HANDS: 1. Pull crown to “C” position 2. Press pusher “A” for 2 seconds 3. Press pusher “B” to “0” setting for the 1/20 sec. hand. If the hand is not at “0” or “12” position, then, press pusher “B” repeatedly, until the hand moves by each intervaI and returns to “0” or “12” position 4. Press pusher “A” for 2 seconds 5. Press pusher “B” to “0” setting for the stopwatch sec. hand. If the hand is not at “0” or “12” position, then, press pusher “B” repeatedly, until the hand moves by each intervaI and returns to “0” or “12” position 6. Press pusher “A” for 2 seconds 7. Press pusher “B” to “0” setting for the stopwatch min. / hour hand. If the hand is not at “0” or “12” position, then, press pusher “B” repeatedly, until the hand moves by each intervaI and returns to “0” or “12” position 8. Push crown to “A” position after the adjustments of all stopwatch hands Note: Please make sure that the stopwatch is stop and reset before adjusting

14 CHRONOGRAPH HAND 1/5 SECOND

PUSHER “A”

A B C HOUR HAND CROWN POSITION

PUSHER “C” PUSHER “B”

ALARM MINUTE HAND 8154/220

2, 6, 10 Three – Eye Chronograph with Alarm Note: Crown position “A”, “B” & “C” Note: Pusher “A” (Top), “B” (Bottom) Note: Left eye “30 minute totalizer” Note: Right eye “second hand” Note: Bottom eye “day calendar”

This chronograph has 4 functions: TIME, DAY & DATE, STOPWATCH, ALARM

TIME To set the time: 1. Pull crown to position “C” 2. Turn crown clockwise / counter clockwise to correct time 3. Push crown to position “A”

15 DAY & DATE CALENDAR To set the day calendar: 1. Pull crown to position “C” 2. Turn crown clockwise / counter clockwise to correct day (bottom eye) 3. Push crown to position “A”

To set the date calendar: 1. Pull crown to position “B” 2. Turn crown clockwise to correct date (window @ 4) 3. Push crown to position “A” Note:It is not possible to correct the date between 9 p.m. and 0:30 a.m.

STOPWATCH The stopwatch is capable of measuring: 1. Minutes (up to 30 minutes) 2. Chronograph hand 1/5 second

Before using the stopwatch, reset the stopwatch hands to the “12” position by pressing pusher “B”. If the stopwatch hands reset improperly, reset the hands as follows:

To reset the stopwatch hands: 1. Press pushers “A” and “B” 2. Press pusher “B” intermittently until the left eye hand is reset to “30” 3. Press pusher “A” intermittently until the chronograph hand resets to “60” 4. Press pusher “A” and “B” Note: PRESSING & HOLDING either pusher “A” or “B” will cause the hands to continue to move until the pusher is released.

16 STANDARD STOPWATCH MEASUREMENT: 1. Press pusher “A” to start timing 2. Press pusher “A” to stop timing 3. Press pusher “B” to reset

ACCUMULATED ELAPSED TIME MEASUREMENT: 1. Press pusher “A” to start timing 2. Press pusher “A” to stop timing 3. Press pusher “A” to restart timing 4. Press pusher “A” to stop 2nd timing etc, etc. 5. Press pusher “B” to reset

SPLIT TIME MEASUREMENT: 1. Press pusher “A” to start timing 2. Press pusher “B” to split 3. Press pusher “B” to begin again 4. Press pusher “A” to stop 5. Press pusher “B” to reset

TIMING 2 EVENTS / COMPETITORS: 1. Press pusher “A” to start timing of 1st event 2. Press pusher “B” to stop timing of 1st event Stopwatch continues to run internally 3. Press pusher “A” to stop timing of 2nd event 4. Press pusher “B” to view time of 2nd event 5. Press pusher “B” to reset

17 ALARM To set the alarm: 1. Pull crown to position “B” 2. Turn crown counter clockwise to set alarm (colour hand) 3. Push crown to position “A”

To activate the alarm: 1. Press pusher “C” to activate the alarm. Watch beeps twice 2. Press pusher “C” again to de-activate alarm. Watch beeps once 3. To stop alarm, press pusher “C” once

18 SECONDS

PUSHER A

A B C MINUTE

CROWN POSITION

DATE PUSHER B

8161/202

2, 6, 10 THREE - EYE CHRONOGRAPH

Note: Crown position “A”, “B” & “C” Note: Pusher “A” (Top), “B” (Bottom) Note: Left eye “minute totalizer” Note: Right eye “small second” Note: Center eye “date indicator”

This Chronograph watch has 3 functions: TIME CALENDAR STOPWATCH

19 TIME To set the time: 1. Pull crown to position “C” 2. Turn crown clockwise / counter clockwise to correct time 3. Push crown to position “A”

CALENDAR To set the calendar: 1. Pull crown to position “B” 2. Turn crown clockwise to correct calendar 3. Push crown to position “A”

STOPWATCH The stopwatch is capable of measuring: 1. 1 minute elasped up to 30 minutes (left eye) 2. Chronograph hand 1/5 second

Before using the stopwatch, reset the stopwatch hands To the “60” position by means of pusher “B”. If stopwatch Hands move improperly, reset the hands as follow:

To reset stopwatch hands: 1. Press pusher “A” & “B” 2. Press pusher “B” intermittently until the left eye hand is reset to “0” 3. Press pusher “A” intermittently until the chronograph hand reset to “60” 4. Press pusher “A” & “B” NOTE: PRESSING & HOLDING either pusher “A” or “B” will Cause the hands to continue to move until the pusher is released.

20 STANDARD STOPWATCH MEASUREMENT: 1. Press pusher “A” to start timing 2. Press pusher “A” to stop timing 3. Press pusher “B” to reset

SPLIT TIME MEASUREMENT: 1. Press pusher “A” to start timing 2. Press pusher “B” to split 3. Press pusher “B’ to begin again 4. Press pusher “A’ to stop 5. Press pusher “B’ to reset

TIMING 2 COMPETITORS: 1. Press pusher “A” to start timing of 1st event 2. Press pusher “B” to stop timing of 1st event stopwatch continues to run internally. 3. Press pusher “A” to stop timing of 2nd event 4. Press pusher “B” to view time of 2nd event 5. Press pusher “B” to reset

21 CHRONOGRAPH HAND 1/5 SECOND

PUSHER “A”

4 A B C

HOUR HAND 4 CROWN POSITION

2 2 PUSHER “C” 3 PUSHER “B”

ALARM MINUTE HAND 8154/221

This chronograph has 4 functions: TIME, DAY & DATE, 5 HOUR CHRONOGRAPH, ALARM

TIME To set the time: 1. Pull crown to position “C” 2. Turn crown clockwise / counter clockwise to correct time 3. Push crown to position “A”

22 DAY & DATE CALENDAR To set the day calendar: 1. Pull crown to position “C” 2. Turn crown clockwise / counter clockwise to correct day (bottom eye) 3. Push crown to position “A” To set the date calendar: 1. Pull crown to position “B” 2. Turn crown clockwise to correct date (window @ 4) 3. Push crown to position “A” Note: It is not possible to correct the date between 9 p.m. and 0:30 a.m.

STOPWATCH 5 hour

Key Features of Stopwatch Mode: 1. This is a stopwatch for timing long PUSHER hours chrono function. 4 hour “A” 2. The dial is designed with 5 hours 1 hour chrono indicator. Please see the diagram. ABC 3. It times speed at 1/5 sec intervals. 4. The split function only available at the first thirty minutes. CROWN 5. After the initial thirty minutes, the POSITION stopwatch will proceed with the PUSHER PUSHER “Hour Chrono Mode” to save the “C” “B” power consumption. (Be ware, in this mode, the big sec hand 3 hour 2 hour moves very slowly and looks like as it has stopped.) 23 TO START THE STOPWATCH: • Push pushers “A”, the big sec will start counting at intervals of 1/5 sec for the first thirty minutes. TO STOP THE STOPWATCH: • Push the pusher “A” again to stop timing. TO RESET THE STOPWATCH: • Push pushers “B”, to reset the stopwatch. Both the big sec. hand and small hand at the small eve at 10 o’clock position will go back to 12 o’clock position. STOPWATCH IN “HOUR CHRONO MODE” After the big sec hand has run for thirty minutes, the watch will stay with the “hour chrono mode”. The big sec hand jumps to the hour indicator to carry on with the timing. (Be ware, in this mode, the big sec hand moves very slowly and looks like as it has stopped.) TO STOP THE STOPWATCH FOR LONG HOURS CHRONO MEASUREMENT: Push pusher “A” will stop the stopwatch. The big sec. hand stops at the hour indicator on the dial to show how many hours the stopwatch has timed. At the same instance, the small eye at 10 o’clock position also shows the minutes timing. Then, press pusher “B” the big sec. hand will jump to show the seconds timing. TO RESET THE STOPWATCH: Push the pusher “B” to reset the stopwatch. Both the big sec. hand and small hand at the small eye at 10 o’clock position will go back to 12 o’clock position.

TO ADJUST STOPWATCH HANDS: 1. Push the pushers “A” and “B” simultaneously and hold for 2 seconds to activate the reset mode. 24 2. Push the pusher “B” to reset the small hand of the eve at 10 o’clock position. After the pusher is pushed, the small sec hand will reach the “30” position exactly. 3. Push the pusher “B” to reset the big sec. hand. When it moves close to the 11 o ‘clock position, adjust it by pushing the button sec by sec until it reaches the 12 o’clock position exactly. 4. Push the pushers “A” and “B” simultaneously and hold for 2 seconds to de- activate the reset mode.

SPLIT TIME MEASUREMENT FOR TIMING TWO RUNNERS: 1. Push the pusher “A” to start the timing of both runners. 2. Push the pusher “B” to split, the big sec. hand stops to show timing of the first runner, but the timing continues internally. 3. Push again the pusher “B” to resume timing, and the hand moves quickly to make up the elapsed time. 4. Push the pusher “A” to indicate the timing of the second runner.

ALARM To set the alarm: 1. Pull crown to position “B” 2. Turn crown counter clockwise to set alarm (colour hand) 3. Push crown to position “A”

25 PERMANENT SECOND HAND

MINUTE CHRONO HAND PUSHER “A”

A B C STOPWATCH SECOND HAND CROWN POSITION

PUSHER “B” HOUR CHRONO HAND DATE 5030D

Note : Crown position “A” “B” and “C” Note : Pusher “A” (Top right) “ B” (Bottom Right) Note : 6 o’ clock eye - Hours elapsed up to 12 hours Note : 9 o’clock eye - Minutes elapsed up to 30 minutes Note : 3 o’clock eye - Permanente second hand

This Chronograph watch has 3 functions : TIME, CALENDAR, STOPWATCH

TIME To set the time : 1. Pull crown to position “C” 2. Turn crown clockwise / counter clockwise to correct time. 3. Push crown back to position “A”

26 CALENDAR To set the Calendar 1. Pull crown to position “B” 2. Turn crown clockwise to correct calendar 3. Push crown back to position “A”

STOPWATCH This stopwatch is capable of measuring : Chrono Hours elapsed up to 12 hours ( 6 o,clock eye) Chrono Minutes elapsed up to 30 minutes ( 9 o,clock eye ) Stopwatch Second up to 1 minute. ( Big second hand )

Before using the stopwatch, reset stopwatch chrono hands to the “12” and “0” position

STANDARD STOPWATCH MEASUREMENT 1. Press pusher “A” to start timing 2. Press pusher “A” again to stop timing 3. Press pusher “B” to reset

Accumulated Elapsed Time Measurement 1. Press pusher “A” to start timing 2. Press pusher “A” again to stop timing 3. Press pusher “A” to restart timing 4. Press pusher “A” again to stop second timing 5. Press pusher “B” to reset

27 SPLIT TIME MEASUREMENT Example of using split time measurement for two runners. Two runners can be timed simultaneously; the first runner’s time can be recorded while the second runner’s time will continue to be accumulated until he finishes.

1. Press pusher “A” to start the timing of the first and second runner 2. Press pusher “B” to stop and record the timing of the first runner. ( Once pusher “B” is activated, even though the chrono minute hand and the big stopwatch sec. hand stop on the dial, the stopwatch still continues to internally.) 3. Press pusher “B” to catch up the timing of the second runner. The stopwatch sec. hand will jump to show internal accumulated time and to carry on timing of the second runner. 4. Press pusher “A” to stop the timing of the second runner and record the time. 5. Press pusher “B” for third time to reset, all stopwatch chrono hands will return to “12” and “0” position.

CORRECTIVE MODE FOR STOPWATCH CHRONO HANDS 1. Pull crown to position “C” 2. Press pushers “A” and “B” simultaneously for at least 2 seconds. 3. The big stopwatch sec hand rotates by 360 degree to activate corrective mode

TO ADJUST THE BIG SEC. STOPWATCH HAND If it is not located at “12” or “0” position, either press pusher “A” continuously or repeatedly until the hand moves by each interval and returns to “12” and “0” position.

28 After finish adjusting big sec. stopwatch hand, press crown back to position “A” to terminate the adjustment.

TO ADJUST THE HOUR CHRONO HAND After activate the corrective mode; if the hour chrono hand in not located at “12” or “0” position, press pusher “B” once to activate the corrective mode of the hour chrono hand. Press pusher “A” continuously or repeatedly until the hand moves by each interval and returns to “12” and “0” position. Press crown back to position “A” to terminate the adjustment.

TO ADJUST THE MINUTE CHRONO HAND After activate the corrective mode; if the minute chrono hand in not located at “12” or “0” position, press pusher “B” twice to activate the corrective mode of the minute chrono hand. Press pusher “A” continuously or repeatedly until the hand moves by each interval and returns to “12” and “0” position. Press crown back to position “A” to terminate the adjustment.

Once finish adjusting all stopwatch chrono hands, press crown back to “A” position to terminate adjustment.

29 24 HOUR HAND

STOPWATCH MINUTE HAND PUSHER “A”

A B C

CROWN POSITION STOPWATCH SECOND HAND PUSHER “B”

SECOND HAND DATE OS20

Note: Crown position "A" "B" &"C" Note: Pusher "A" ( Top Right), Pusher 'B" ( Bottom Right) Note: 3 o'clock eye - 24 hour hand Note: 6 o'clock eye - second hand Note : 9 o'clock eye - stopwatch minute hand This Chronograph watch has three functions : TIME, CALENDAR, STOPWATCH TIME To set the time: 1. Pull crown to position "C" 2. Turn crown clockwise / counter clockwise to correct time 3. Push crown to position "A"

30 Remarks: When crown is pushed back to position "A," small second hand begins to run. CALENDAR To set the calendar 1. Pull crown to position "B" 2. Turn crown counter-clockwise to set calendar 3. Push crown to position "A" STOPWATCH The stopwatch is capable to measure and display time in 1/1 second united up to maximum of 59 minutes 59 seconds.

1. Press pusher "A" to start timing 2. Press pusher "A" again to stop timing 3. Press pusher "B" to reset CORRECTING STOPWATCH HAND If after resetting the stopwatch second hand and found that it is not at the "12" or "0" position, correct it as follows:

1. Pull crown to "C" position 2. Press pusher "A" continuously, the stopwatch second hand will be advanced rapidly until it gets closely to the "12" position. Then, press pusher "A" repeatedly, the stopwatch second hand will be moved by interval until it returns to "12" position. 3. Push crown to position 'A"

31 STOPWATCH MINUTES HAND MINUTE HAND PUSHER “A”

CROWN POSITION HOUR HAND

STOPWATCH A B C SECOND HAND PUSHER “B”

PERMANENT DATE SECOND HAND OS11

Note: Crown Position “A” “B” & “C” Note: Pusher “A” (Top right), Pusher “B” (Bottom Right ) Note: 12 o’clock eye chrono minute hand Note: 6 o’clock permanent second hand

This Chronograph watch has 3 functions TIME, CALENDAR, STOPWATCH

TIME To set the time : 1. Pull crown to position “C” 2. Turn crown counter clockwise to correct time 3. Push crown to position “A”

32 CALENDAR To set the calendar 1. Pull out the crown to position B. 2. Turn crown counter clockwise to correct calendar 3. Push in the crown to position A.

STOPWATCH This watch is capable to measure and display 1 second unit up to maximum of 60 minutes 1. Press pusher “B” to enter to chrono mode. 2. Press pusher “A” to start the timing 3. Press pusher “A” again to stop timing 4. Press pusher “B” to reset

CORRECTING STOPWATCH HANDS TO “12” OR “0” POSITION 1. Pull crown to position “B” 2. Press pusher "A" until both second and minute chrono hands return to "12" or "0" position. 3. Once the hands have been corrected, reset the time and press crown to position “A” Note:Do not push crown to position “A” while correcting chrono hands

33 STOPWATCH MINUTE HAND PUSHER “A”

CROWN POSITION CHRONOGRAPH HAND 1/5 SECOND A B C

PUSHER “B”

SECOND HAND YM91

Note : Crown position “A” “B” and “C” Note: Pusher “A” ( Top Right ), “B” ( Bottom Right) Note: 12 o’clock eye - Stopwatch minute hand Note : 6 o’clock eye - Second hand

This Chronograph watch has three functions : TIME, CALENDAR, STOPWATCH

TIME To set the time: 1. Pull crown to position “C” 2. Turn crown clockwise / counter clockwise to correct time 3. Push crown to position “A”

34 CALENDAR To set the calendar: 1. Pull crown to position “B” 2. Turn crown clockwise to correct calendar 3. Push crown to position “A” STOPWATCH This stopwatch is capable of measuring : – 1/5 second elapsed up to 60 minutes –After 60 minutes, it will start counting again from “0” repeatedly up to 12 hours

Before using the stopwatch, reset the stopwatch hands To the “12” and “0” position. STANDARD STOPWATCH MEASUREMENT: 1. Press pusher “A” to start timing 2. Press pusher “A” to stop timing 3. Press pusher “B” to reset ACCUMULATED ELAPSED TIME MEASUREMENT: 1. Press pusher “A” to start timing 2. Press pusher “A” to stop timing 3. Press pusher “A” to restart timing 4. Press pusher “A” to stop 2nd timing 5. Press pusher “B” to reset

35 SPLIT TIME MEASUREMENT: 1. Press pusher “A” to start the timing of the first runner 2. Press pusher “B” to stop and record the timing of the first runner. (Once pusher B is activated, even though the stopwatch 1/20 sec. hand and the big stopwatch sec. hand stop on the dial, the stopwatch still continues to time internally.) 3. Press pusher “B” to start the timing of the second runner. The stopwatch sec. hand will jump to show internal accumulated time and to carry on timing of the second runner. 4. Press pusher “A” to stop the timing of the second runner and record the time 5. Press pusher “B” for third time to reset, all stop watch hands will return to 12 o’clock position.

TO ADJUST STOPWATCH HAND 1. Pull crown to position “C” 2. Press pusher “A” for 2 seconds, the stopwatch minute hand turns a full cycle 3. Press pusher “B” repeatedly to set stopwatch minute hand to “0” position. 4. Press pusher “A” again for 2 seconds, the stopwatch sceond hand turns a full cycle 5. Press pusher “B” repeatedly to set stopwatch second hand to “0” position. 6. Push crown to position “A”

Remarks : This is suggested to check the hour and minute hand to ensure it is correct before push the crown back to position “A”

36 37 LIMITED WARRANTY The Basic Coverage: This NAUTICA watch (but not any battery, crystal, case, band or strap) is warranted to the owner for a period of FIVE YEARS from the date of purchase against defects In manufacture by Nautica Watches - not by the dealer from whom the watch was purchased.

What Nautica Watches Will Do: If this watch develops such a defect within the five year period it will be repaired (i. e., a new or thoroughly reconditioned and inspected movement will be installed) or replaced (a watch of equal value and similar appearance will be supplied) at our option, provided it is returned with a $7.50 check or money order to cover costs of postage, handling and service, and you provide proof of purchase and date of purchase.

This Limited Warranty Does Not Cover: 1) Nautica Watches will not repair defects related to servicing not performed by Nautica Watches. 2) Nautica Watches will not provide any warranty service if your watch shows evidence that it has been tampered with, misused, abused, or altered; for example: • moisture damage sufficient to affect the proper function of the watch; • damage to the case; or • visible cracking of the crystal. 3) Nautica Watches reserves the right to charge you for a replacement battery, if the battery in your watch is depleted. No additional charge will be made unless the five year warranty period has expired or servicing is necessary for reasons beyond our control, in which case a moderate charge will be made. 4) NAUTICA WATCHES IS NOT LIABLE FOR INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES. Some states do not allow the exclusion or limitation of incidental, special or consequential damages, so the above exclusion or limitation may not apply to you. Your Rights Under Implied Warranties and State Law: THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER EXPRESSED WARRANTIES, OBLIGATIONS OR LIABILITIES. NAUTICA WATCHES LIMITS THE DURATION OF ANY WARRANTY IMPLIED BY STATE LAW, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, TO FIVE YEARS FROM THE DATE OF ORIGINAL PURCHASE. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Care of Your Watch: •Avoid exposing your watch to water, steam, or other forms of moisture, if your watch is not water-resistant. • If the crystal becomes damaged, have it replaced at once to avoid damage to the movement. • When your battery is depleted, have it replaced promptly. The particular type of battery required is indicated on your caseback.

Service of Your Watch: If your NAUTICA watch should ever need servicing, send it to: NAUTICA HOTLINE WATCH SERVICE CALLANEN INTERNATIONAL 145 Woodward Avenue, Norwalk, CT 06854 Attn: The Repair Department Because of possible loss, we recommend insuring your watch, return receipt requested, when using the mails. If you do not obtain a receipt within a reasonable time, start a tracer through the originating post office. NEVER INCLUDE A SPECIAL WATCHBAND OR ANY OTHER ARTICLE OF PERSONAL VALUE IN YOUR SHIPMENT. PLEASE NOTE THAT WE MAY SUBSTITUTE A WATCH OF EQUAL VALUE AND SIMILAR APPEARANCE FOR YOURS ON BOTH IN-WARRANTY AND OUT-OF-WARRANTY REPAIRS.