DOCSLIB.ORG

101 Lime Solvent

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
101 Lime Solvent Sure Klean® CLEANING & PROTECTIVE TREATMENTS 101 Lime Solvent Sure Klean® 101 Lime Solvent is a concentrated acidic cleaner for dark-colored brick and tile REGULATORY COMPLIANCE surfaces which are not subject to metallic oxidation. VOC Compliance Safely removes excess mortar and construction dirt. Sure Klean® 101 Lime Solvent is compliant with all national, state and district VOC regulations. ADVANTAGES • Removes construction dirt and excess mortar with TYPICAL TECHNICAL DATA simple cold water rinse. Clear, brown liquid • Removes efflorescence from new brick and new FORM Pungent odor stone construction. SPECIFIC GRAVITY 1.12 • Safer than muriatic acid on colored mortar and dark-colored new masonry surfaces. pH 0.50 @ 1:6 dilution • Proven effective since 1954. WT/GAL 9.39 lbs Limitations ACTIVE CONTENT not applicable • Not generally effective in removal of atmospheric TOTAL SOLIDS not applicable stains and black carbon found on older masonry VOC CONTENT not applicable surfaces. Use the appropriate Sure Klean® FLASH POINT not applicable restoration cleaner to remove atmospheric staining from older masonry surfaces. FREEZE POINT <–22° F (<–30° C) • Not for use on polished natural stone. SHELF LIFE 3 years in tightly sealed, • Not for use on treated low-E glass; acrylic and unopened container polycarbonate sheet glazing; and glazing with surface-applied reflective, metallic or other synthetic coatings and films. SAFETY INFORMATION Always read full label and SDS for precautionary instructions before use. Use appropriate safety equipment and job site controls during application and handling. 24-Hour Emergency Information: INFOTRAC at 800-535-5053 Product Data Sheet • Page 1 of 4 • Item #10010 – 102715 • ©2015 PROSOCO, Inc. • www.prosoco.com Product Data Sheet Sure Klean® 101 Lime Solvent Construction soiling and mortar residues on new PREPARATION brick and tile surfaces clean most effectively if the Protect people, vehicles, property, metal, painted cleaning is done within 14–28 days of installation. surfaces, plants and other non masonry materials Mortar and grout smears left on the surface longer from product, splash, rinse, wind drift and fumes. result in a more difficult clean down and may cause When working over traffic, clean when traffic is at undesirable results. Cleaning high-strength mortar/ a minimum. Protect or divert traffic if necessary. grout within seven days improves results. Vapors and liquid can damage a variety of metals and NOTE: Excessive moisture in the wall contributes fabrics. Clean masonry before installing windows, to efflorescence and other staining. Always protect doors, finished flooring, metal fixtures, hardware, open wall cavities from rain during construction. light fixtures, roofing materials and other non masonry items the cleaner could harm. If already Surface and Air Temperatures installed, protect with polyethylene before application. Best air and masonry temperatures for cleaning are Sure Klean® Strippable Masking is appropriate for use 40° F (4° C) or above. Cleaning when temperatures with this product to protect windows. are below freezing or will be overnight may Maintain ventilation to avoid buildup of potentially harm masonry. If freezing conditions exist before damaging fumes. All caulking and sealant application, let masonry thaw first. materials should be in place and thoroughly cured before cleaning. Equipment Apply with low-pressure (50 psi max) spray or densely-packed, soft-fibered masonry washing Recommended for these substrates. Always test. brush. Do not atomize. Do not apply with pressure Coverage is in sq.ft./m. per gallon of concentrate. spray above 50 psi. This drives the chemicals deep Substrate Type Use? Coverage into the surface, making complete rinse difficult. Burnished no Use acid-resistant rigging and safety equipment. Architectural Smooth yes 500–900 sq.ft. Test spray equipment for compatibility and to avoid Concrete Block Split-faced yes 46–84 sq.m. discoloration. Ribbed yes Rinse with enough water and pressure to flush Brick yes spent cleaner and dissolved soiling from the Tile yes 500–900 sq.ft. masonry surface and surface pores without Concrete Precast Panels yes 46–84 sq.m. damage. Inadequate rinsing leaves residues which Pavers yes may stain the cleaned surface. Cast-in-place yes Brick yes Masonry-washing equipment generating 400–1000 Tile yes 500–900 sq.ft. psi with a water flow rate of 6–8 gallons per minute Fired Clay Terra Cotta (unglazed) yes 46–84 sq.m. is the best water/pressure combination for rinsing Pavers yes porous masonry. Use a 15–45° fan spray tip. Heated water (150–180° F; 65–82° C) may improve cleaning Marble, Polished no N/A efficiency. Use adjustable equipment for reducing Travertine, Limestone Unpolished no N/A water flow-rates and rinsing pressure as needed for sensitive surfaces. Polished no N/A Rinsing pressures greater than 1000 psi and fan Granite 700–900 sq.ft. Unpolished yes spray tips smaller than 15° may permanently 65–84 sq.m. damage sensitive masonry. Water flow-rates less 500–900 sq.ft. Sandstone Unpolished yes than 6 gallons per minute may reduce cleaning 46–84 sq.m. productivity and contribute to uneven cleaning 700–900 sq.ft. results. Slate Unpolished yes 65–84 sq.m. Storage and Handling Repeated applications may damage surfaces. Sure Klean® Custom Masonry Cleaner is a more appropriate product. Transport and store in a cool, dry place with Sure Klean® Light Duty Concrete Cleaner is a more adequate ventilation. Vapors and liquid can appropriate product. damage a variety of metals and fabrics. Always Always test to ensure desired results. Coverage estimates seal container after dispensing. Do not alter or mix depend on surface texture and porosity. with other chemicals. Published shelf life assumes Product Data Sheet • Page 2 of 4 • Item #10010 – 102715 • ©2015 PROSOCO, Inc. • www.prosoco.com Product Data Sheet Sure Klean® 101 Lime Solvent upright storage of factory-sealed container in a dry Application Instructions place. Maintain temperatures of 45–100° F (7–38° Test thoroughly before cleaning. Provide adequate C). Do not double stack pallets. Dispose of unused ventilation. CAUTION: Multiple applications may product and container in accordance with local, affect the mortar color. state and federal regulations. Exterior Surfaces APPLICATION 1. Working from the bottom to the top, prewet a Read “Preparation” and the Safety Data Sheet before large area with fresh water. use. 2. Apply the diluted solution freely from the bottom of the work area up. ALWAYS TEST a small area (minimum 4-ft x 4-ft) of each surface to confirm suitability and desired 3. Let cleaning solution stay on the wall for 1–3 results before beginning overall application. Test minutes. Do not let cleaner dry into the masonry. each type of masonry and each type of stain. Test This may leave residue and stains. Fresh-water with the same equipment, recommended surface rinse the surfaces below areas being cleaned to preparation and application procedures planned prevent streaking. for general application. Let test area dry 3–7 days 4. Immediately reapply cleaning solution and before inspection and approval. Make the test panel scrape off heavy buildup of excess mortar using a available for comparison throughout the cleaning wooden scraper or piece of brick. Take care not to project. harm the masonry surface. 5. Working from the bottom of the work area to the Dilution top, rinse thoroughly with fresh water, removing Do not dilute product except as specified below. Do all cleaning compound, free sand, loose material not alter or mix with chlorine-type bleaches or other and debris. chemicals (may release toxic gases). Do not use for 6. Reapply as required following steps 1 through 5. applications other than specified. Handle in polypropylene buckets only. No metal Interior Surfaces buckets or sprayers. Acidic materials and fumes Proper ventilation is necessary. Test thoroughly. attack metal. Follow preceding preparation and cleaning procedures for exteriors. Rinse thoroughly with Dilute one part product with between 4 and 8 parts fresh water using a sponge or soft-fibered brush. clean water, based on test results. Always pour COLD water into empty bucket first, then carefully If there isn’t enough water for complete rinsing, add product. Never use hot water. More porous use neutralizing rinse following this procedure: masonry and high-strength mortar/grout will 1. Rinse with clear water. require stronger solutions. Clean glazed surfaces 2. Apply neutralizing rinse of 2 ounces baking soda with the mildest solution possible to avoid harm. to 1 gallon water. Always test to the final dilution that cleans best. 3. Saturate. Leave solution on surface 3–5 minutes. 4. Apply final rinse of clear water. brush. Do not atomize. Do not apply with pressure BEST PRACTICES spray above 50 psi. This drives the chemicals deep into the surface, making complete rinse difficult. Construction soiling and mortar residues on new Test spray equipment for compatibility and to brick and tile surfaces clean most effectively if the avoid discoloration. cleaning is done within 14–28 days of installation. Mortar and grout smears left on the surface longer Rinse with enough water and pressure to flush result in a more difficult clean down and may spent cleaner and dissolved soiling from the cause undesirable results. Cleaning high-strength masonry surface and surface pores without mortar/grout within 7 days improves results. damage. Inadequate rinsing leaves residues which may stain the cleaned surface. Excessive moisture in the wall contributes to efflorescence and other staining. Always protect Never go it alone. For problems or questions, open wall cavities from rain during construction. contact your local PROSOCO distributor or field representative. Or call PROSOCO technical Apply with low-pressure (50 psi max) spray or Customer Care toll-free at 800-255-4255. densely-packed, soft-fibered masonry washing Product Data Sheet • Page 3 of 4 • Item #10010 – 102715 • ©2015 PROSOCO, Inc. • www.prosoco.com Product Data Sheet Sure Klean® 101 Lime Solvent Cleanup tests to determine the suitability of this product for Clean tools and equipment using fresh water.
Load more

Recommended publications
  • Solvent Effects on the Thermodynamic Functions of Dissociation of Anilines and Phenols
    University of Wollongong Research Online University of Wollongong Thesis Collection 1954-2016 University of Wollongong Thesis Collections 1982 Solvent effects on the thermodynamic functions of dissociation of anilines and phenols Barkat A. Khawaja University of Wollongong Follow this and additional works at: https://ro.uow.edu.au/theses University of Wollongong Copyright Warning You may print or download ONE copy of this document for the purpose of your own research or study. The University does not authorise you to copy, communicate or otherwise make available electronically to any other person any copyright material contained on this site. You are reminded of the following: This work is copyright. Apart from any use permitted under the Copyright Act 1968, no part of this work may be reproduced by any process, nor may any other exclusive right be exercised, without the permission of the author. Copyright owners are entitled to take legal action against persons who infringe their copyright. A reproduction of material that is protected by copyright may be a copyright infringement. A court may impose penalties and award damages in relation to offences and infringements relating to copyright material. Higher penalties may apply, and higher damages may be awarded, for offences and infringements involving the conversion of material into digital or electronic form. Unless otherwise indicated, the views expressed in this thesis are those of the author and do not necessarily represent the views of the University of Wollongong. Recommended Citation Khawaja, Barkat A., Solvent effects on the thermodynamic functions of dissociation of anilines and phenols, Master of Science thesis, Department of Chemistry, University of Wollongong, 1982.
    [Show full text]
  • Solvent-Tunable Binding of Hydrophilic and Hydrophobic Guests by Amphiphilic Molecular Baskets Yan Zhao Iowa State University, [email protected]
    Chemistry Publications Chemistry 8-2005 Solvent-Tunable Binding of Hydrophilic and Hydrophobic Guests by Amphiphilic Molecular Baskets Yan Zhao Iowa State University, [email protected] Eui-Hyun Ryu Iowa State University Follow this and additional works at: http://lib.dr.iastate.edu/chem_pubs Part of the Chemistry Commons The ompc lete bibliographic information for this item can be found at http://lib.dr.iastate.edu/ chem_pubs/197. For information on how to cite this item, please visit http://lib.dr.iastate.edu/ howtocite.html. This Article is brought to you for free and open access by the Chemistry at Iowa State University Digital Repository. It has been accepted for inclusion in Chemistry Publications by an authorized administrator of Iowa State University Digital Repository. For more information, please contact [email protected]. Solvent-Tunable Binding of Hydrophilic and Hydrophobic Guests by Amphiphilic Molecular Baskets Abstract Responsive amphiphilic molecular baskets were obtained by attaching four facially amphiphilic cholate groups to a tetraaminocalixarene scaffold. Their binding properties can be switched by solvent changes. In nonpolar solvents, the molecules utilize the hydrophilic faces of the cholates to bind hydrophilic molecules such as glucose derivatives. In polar solvents, the molecules employ the hydrophobic faces of the cholates to bind hydrophobic guests. A water-soluble basket can bind polycyclic aromatic hydrocarbons including anthracene, pyrene, and perylene. The binding free energy (−ΔG) ranges from 5 to 8 kcal/mol and is directly proportional to the surface area of the aromatic hosts. Binding of both hydrophilic and hydrophobic guests is driven by solvophobic interactions. Disciplines Chemistry Comments Reprinted (adapted) with permission from Journal of Organic Chemistry 70 (2005): 7585, doi:10.1021/ jo051127f.
    [Show full text]
  • I. the Nature of Solutions
    Solutions The Nature of Solutions Definitions Solution - homogeneous mixture Solute - substance being dissolved Solvent - present in greater amount Types of Solutions SOLUTE – the part of a Solute Solvent Example solution that is being dissolved (usually the solid solid ? lesser amount) solid liquid ? SOLVENT – the part of a solution that gas solid ? dissolves the solute (usually the greater liquid liquid ? amount) gas liquid ? Solute + Solvent = Solution gas gas ? Is it a Solution? Homogeneous Mixture (Solution) Tyndall no Effect? Solution Is it a Solution? Solution • homogeneous • very small particles • no Tyndall effect • particles don’t settle • Ex: •rubbing alcohol Is it a Solution? Homogeneous Mixture (Solution) Tyndall no Effect? yes Solution Suspension, Colloid, or Emulsion Will mixture separate if allowed to stand? no Colloid (very fine solid in liquid) Is it a Solution? Colloid • homogeneous • very fine particles • Tyndall effect • particles don’t settle • Ex: •milk Is it a Solution? Homogeneous Mixture (Solution) Tyndall Effect? no yes Solution Suspension, Colloid, or Emulsion Will mixture separate if allowed to stand? no yes Colloid Suspension or Emulsion Solid or liquid particles? solid Suspension (course solid in liquid) Is it a Solution? Suspension • homogeneous • large particles • Tyndall effect • particles settle if given enough time • Ex: • Pepto-Bismol • Fresh-squeezed lemonade Is it a Solution? Homogeneous Mixture (Solution) Tyndall no Effect? yes Solution Suspension, Colloid, or Emulsion Will mixture separate if allowed to stand? no yes Colloid Suspension or Emulsion Solid or liquid particles? solid liquid Suspension (course solid in liquid) Emulsion (liquid in liquid) Is it a Solution? Emulsion • homogeneous • mixture of two immiscible liquids • Tyndall effect • particles settle if given enough time • Ex: • Mayonnaise Pure Substances vs.
    [Show full text]
  • Chapter 18 Solutions and Their Behavior
    Chapter 18 Solutions and Their Behavior 18.1 Properties of Solutions Lesson Objectives The student will: • define a solution. • describe the composition of solutions. • define the terms solute and solvent. • identify the solute and solvent in a solution. • describe the different types of solutions and give examples of each type. • define colloids and suspensions. • explain the differences among solutions, colloids, and suspensions. • list some common examples of colloids. Vocabulary • colloid • solute • solution • solvent • suspension • Tyndall effect Introduction In this chapter, we begin our study of solution chemistry. We all might think that we know what a solution is, listing a drink like tea or soda as an example of a solution. What you might not have realized, however, is that the air or alloys such as brass are all classified as solutions. Why are these classified as solutions? Why wouldn’t milk be classified as a true solution? To answer these questions, we have to learn some specific properties of solutions. Let’s begin with the definition of a solution and look at some of the different types of solutions. www.ck12.org 394 E-Book Page 402 Homogeneous Mixtures A solution is a homogeneous mixture of substances (the prefix “homo-” means “same”), meaning that the properties are the same throughout the solution. Take, for example, the vinegar that is used in cooking. Vinegar is approximately 5% acetic acid in water. This means that every teaspoon of vinegar contains 5% acetic acid and 95% water. When a solution is said to have uniform properties, the definition is referring to properties at the particle level.
    [Show full text]
  • Aqueous Solution → Water Is the Solvent Water
    Chem 1A Name:_________________________ Chapter 4 Exercises Solution a homogeneous mixture = A solvent + solute(s) Aqueous solution water is the solvent Water – a polar solvent: dissolves most ionic compounds as well as many molecular compounds Aqueous solution: Strong electrolyte – contains lots of freely moving ions Weak electrolyte – contains a little amount of freely moving ions Nonelectrolyte – does not contain ions Solution concentrations: Mass of Solute Percent (by mass) = x 100% Mass of Solution For example, if 1.00 kg of seawater contains 35 g of sodium chloride, the percent of NaCl in seawater is 35 g x 100% = 3.5% 1000 g If a solution contains 25 g NaCl dissolved in 100. g of water, the mass percent of NaCl in the solution is 25 g x 100% = 20.% (100 + 25) g (A solution that contains 20.% (by mass) of NaCl means that for every 100 g of the solution, there will be 20 g of NaCl. Therefore, if seawater contains 3.5% NaCl, for every 100 g of seawater, there are 3.5 g of NaCl.) Volume of Solute Percent (by volume) = x 100% Volume of Solution For example, if 750 mL of white wine contains 80. mL of ethanol, the percent of ethanol by volume is 80. mL x 100% = 11% 750 mL (A solution that contains 11% ethanol (by volume) means that for every 100 mL of the solution, there will be 11 mL of ethanol in it. However, unlike mass, volume addition is not always additive – meaning that if you add 11 mL of ethanol and 89 mL of water, the total is not 100 mL.
    [Show full text]
  • Carbon Consolidation Methodology
    Clean Water Standards Waste Water Quality Standards Version: V1 – 2015_07_17 1 Danone group : Waste Water Quality Standards Table of content 1 Introduction ................................................................................................. 3 2 Definition ..................................................................................................... 3 3 Scope of application ..................................................................................... 4 4 DANONE’s Ambition and Site’s Objectives ................................................... 4 5 Indicators: .................................................................................................... 4 5.1 KPI (type, class, threshold, monitoring and analysis frequency) ............. 4 5.2 Analytical Methods ................................................................................ 6 6 Operational Guidelines: ............................................................................... 6 7 Peak management: What to do in case of threshold exceeding? ................. 6 8 Reporting Guidance and Objective ............................................................... 9 9 APPENDICES ............................................................................................... 10 2 Danone group : Waste Water Quality Standards 1 Introduction The impact on ecosystems coming from our activities and specifically from discharges of waste water has been identified as a risk as regulatory, operational or reputational, and potentially affecting the site
    [Show full text]
  • A Solution Is a Type of Mixture
    ¡ ¢ £ ¤ ¥ ¦ § KEY CONCEPT A solution is a type of mixture. BEFORE, you learned NOW, you will learn • Ionic or covalent bonds hold a • How a solution differs from compound together other types of mixtures • Chemical reactions produce • About the parts of a solution chemical changes • How properties of solutions • Chemical reactions alter the differ from properties of their arrangements of atoms separate components VOCABULARY EXPLORE Mixtures solution p. 111 Which substances dissolve in water? solute p. 112 solvent p. 112 PROCEDURE MATERIALS suspension p. 113 • tap water 1 Pour equal amounts of water into each cup. • 2 clear plastic cups 2 Pour one spoonful of table salt into one • plastic spoon of the cups. Stir. • table salt • flour 3 Pour one spoonful of flour into the other cup. Stir. 4 Record your observations. WHAT DO YOU THINK? • Did the salt dissolve? Did the flour dissolve? • How can you tell? The parts of a solution are mixed evenly. VOCABULARY A mixture is a combination of substances, such as a fruit salad. Remember to use the The ingredients of any mixture can be physically separated from each strategy of your choice. You might use a four square other because they are not chemically changed—they are still the same diagram for solution . substances. Sometimes, however, a mixture is so completely blended that its ingredients cannot be identified as different substances. A solution is a type of mixture, called a homogeneous mixture, that is the same throughout. A solution can be physically separated, but all portions of a solution have the same properties. If you stir sand into a glass of water, you can identify the sand as a separate substance that falls to the bottom of the glass.
    [Show full text]
  • An Introduction to the Acid Dossociation Constant (Pka)
    Technical Document An Introduction to the Acid Dissociation Constant (pKa ) Advanced Chemistry Development, Inc. Toronto, ON, Canada www.acdlabs.com + pKa is a measure of the tendency of a molecule or ion to keep a proton, H , at its ionization center(s). It is related to the ionization capabilities of chemical species. The more likely that ionization occurs, the more likely a species will be taken up into aqueous solution, because water is a very polar solvent (dielectric constant, ε20 = 80). If a molecule does not readily ionize, then it will tend to stay in a non- polar solvent such as cyclohexane (ε20 = 2) or octanol (ε20 = 10). In biological terms, pKa is thus an important concept in determining whether a molecule will be taken up by aqueous tissue components or the lipid membranes. It is also closely related to the concepts of pH (the acidity of solution) and logP (the partition coefficient between immiscible liquids). The equilibrium acid ionization constant, Ka, expresses the ratio of concentrations for the reaction: - - HA + H2O → H3O+ + A Ka = [H3O+] [A ] / [HA] where, by convention, it is assumed that the concentration of water is constant, and is absorbed into the Ka definition. The acid ionization constant varies by orders of magnitude. For example, at 25°C: -5 -10 acetic acid: Ka = 1.8 x 10 phenol: Ka = 1.0 x 10 It is easier to refer to such extreme numbers on a logarithmic scale and, again by convention, "p" is used to denote the negative logarithm (base 10): pKa = -log(Ka) The Ka values of the compounds above are then easily converted to pKa values: acetic acid: pKa = -log(1.8 x 10-5) = 4.756 phenol: pKa = -log(1.0 x 10-10) = 10.0 There is an essential difference between interpreting the pKa values for molecules vs.
    [Show full text]
  • 8.4 Solvents in Organic Chemistry 339
    08_BRCLoudon_pgs5-1.qxd 12/8/08 11:05 AM Page 339 8.4 SOLVENTS IN ORGANIC CHEMISTRY 339 8.14 Label each of the following molecules as a hydrogen-bond acceptor, donor, or both. Indicate 1 the hydrogen that is donated1 or the atom that serves as the hydrogen-bond acceptor. (a) H Br (b) H F (c) O L 1 3 L 1 3 S3 3 H3C C CH3 L L 1 | (d) O 1 (e) (f) H3C CH2 NH3 S3 3 OH L L H3C C NH CH3 cL 1 L L L 8.4 SOLVENTS IN ORGANIC CHEMISTRY A solvent is a liquid used to dissolve a compound. Solvents have tremendous practical impor- tance. They affect the acidities and basicities of solutes. In some cases, the choice of a solvent can have dramatic effects on reaction rates and even on the outcome of a reaction. Understand- ing effects like these requires a classification of solvent types, to which Section 8.4A is devoted. The rational choice of a solvent requires an understanding of solubility—that is, how well a given compound dissolves in a particular solvent. Section 8.4B discusses the principles that will allow you to make general predictions about the solubilities of both covalent organic com- pounds and ions in different solvents. The effects of solvents on chemical reactions are closely tied to the principles of solubility. Solubility is also important in biology. For example, the solubilities of drugs determine the forms in which they are marketed and used, and such important characteristics as whether they are absorbed from the gut and whether they pass from the bloodstream into the brain.
    [Show full text]
  • Solute - Solvent
    Unit 7.3 Solutions: Solute - Solvent Is snow an aqueous solution? In the winter, the temperature often gets well below the freezing point of water. This condition can create problem in car radiators. If the water freezes, water hoses will break, the engine block can crack, and significant damage can be done to the car. Solute and Solvent When one substance dissolves into another, a solution is formed. A solution is a homogeneous mixture consisting of a solute dissolved into a solvent. The solute is the substance that is being dissolved, while the solvent is the dissolving medium. Solutions can be formed with many different types and forms of solutes and solvents. Types of Solutions Type Solvent Solute Example gas/gas nitrogen oxygen air liquid/gas water carbon dioxide soda pop liquid/liquid water ethylene glycol antifreeze liquid/solid water salts seawater solid/solid iron carbon and chromium stainless steel (alloys) Gas Solutions Our air is a homogeneous mixture of many different gases and therefore qualifies as a solution. Approximately 78% of the atmosphere is nitrogen, making it the solvent for this solution. The next major constituent is oxygen (about 21%), followed by the inert gas argon (0.9%), carbon dioxide (0.04%) and trace amounts of neon, methane, helium, and other gases. Solid-Solid Solutions Solid-solid solutions such as brass, bronze, and sterling silver are called alloys. Bronze (composed mainly of copper with added tin) was widely used in making weapons in times past dating back to at least 2400 B.C. This metal alloy was hard and tough, but was eventually replaced by iron.
    [Show full text]
  • What Is a Solvent? Where Are Solvents Used?
    OSH Brief No. 5 What is a solvent? Where are solvents used? The term 'solvent' is applied to a large number of You are most likely to be exposed to solvents if chemical substances which are used to dissolve you work in industries where they are used or dilute other substances or materials. They are extensively. usually organic liquids. Many solvents are also used as chemical intermediates, fuels, and as components of a wide range of products. Industries where solvents are most likely used Common examples of solvents • Engineering • Footwear • Construction • Textiles • acetone • Chemicals • Foodstuff • petroleum spirits • Printing • Woodworking • dichloromethane • Rubber • Dry cleaning • 1.1.1-trichloroethane • Plastics • hexane • Ink manufacture • toluene • Pharmaceutical manufacture • methanol • Paint manufacture • trichloroethylene • methyl ethyl ketone • xylene In the construction industry, for example, • perchloroethylene solvents act as carriers for surface coatings such • white spirit as paints, varnishes and adhesives. The most common solvents found in construction are: • white spirit - in paints, varnishes and cleaning Industrial solvents are often mixtures of several products; individual substances and can be found under a • xylene - in paints and adhesives; variety of trade names. • 1-butanol - in natural and synthetic resins, paints and lacquers. Solvents are also found in many products What are the main health effects? including: • cleaning and degreasing materials; The main effects of solvents are irritation of the • paint removers; skin, eyes and lungs, headache, nausea, dizziness • paints, lacquers and varnishes; and light¬headedness. Exposure can impair co- • adhesives; ordination and this can make people more prone • inks and ink removers; to accidents, such as falling off ladders.
    [Show full text]
  • Polymer-To-Solvent Reference Table for GPC/SEC
    Polymer-to-Solvent Reference Table for GPC/SEC Technical Overview Author Abstract Adam Bivens, A comprehensive reference on solvents for gel permeation chromatography, with Agilent Technologies a full list of tested solvent, polymer, and column combinations, and notes on best practices. Introduction Experimental Each chemistry was formulated to be noninteractive to a wide variety of Gel permeation chromatography For GPC to yield valid data, the analytes polymers dissolved in their respective (GPC), which is also referred to as size must not stick to the surface of the solvents. Polymeric media allow for exclusion chromatography (SEC) or gel particle, as this would cause the retention both wide pores and a single, consistent fi ltration chromatography (GFC), provides time to no longer refl ect just size, but also surface chemistry free of interactive size-based separation by allowing surface interaction effects. silanols or metal centers found on other analytes with small size in solution materials. to diffuse into the pores of the media, To overcome this challenge, Agilent provides three phase chemistries that while analytes that are too large to fi t Over its 40-year history, Agilent has minimize surface interaction in their into these pores are swept through the assembled a vast library of applications respective solvents: column by the solvent. for GPC, which are summarized in Table 2. Pore size and distribution can • PLgel – A highly cross-linked be manipulated to change the polystyrene-divinylbenzene retention-to-size relationship and (PS-DVB) particle compatible with Table 1. Chemical acronyms. the range of separable sizes. This organic and many polar organic THF Tetrahydrofuran retention-to-size relationship is solvents.
    [Show full text]