DOCSLIB.ORG

Trusted by More Professionals

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Trusted by More Professionals LIMITED SLIP DIFFERENTIAL Identification and Application Chart THE #1 BRAND For use in all clutch-type limited slip differentials TRUSTED BY MORE Eliminate differential chatter and noise PROFESSIONALS Reduce differential oil temperatures Extend clutch pack and equipment life LUBEGARD Universal Limited Slip Supplement can be used in place of Ford, Chrysler, and General Motors friction modifier additives for limited slip differentials. IMPORTANT! Please be sure to adequately research technical resources such as your vehicle’s manual to determine the type of assembly for your application. LUBEGARD Limited Slip Supplement is only for use in clutch-type limited slip differentials. INTERNATIONAL LUBRICANTS, INC. a STELLAR AUTOMOTIVE GROUP COMPANY 7930 Occidental South Seattle, WA 98108 206-762-5343 800-333-LUBE (5823) ©2013 ILI. All trademarks are property of their respective owners. www.Lubegard.com Differential Identification AAM 9.25” AAM 10.5” AAM 11.5” AMC Model 20 AMC Model 35 Chrysler 7.25” Chrysler 8.25” Chrysler 9.25” Dana 30 Dana 35 Dana 44 Dana 60 Dana 70 Dana 80 Ford 7.5” Ford 8.8” Requires an additional 4 oz’s Requires an additional 4 oz’s Requires an additional 4 oz’s Ford 8” Ford 9” Ford 9.75” Ford 10.25” & 10.5” General Motors 7.5” Requires an additional 4 oz’s Requires an additional 4 oz’s General Motors 8” General Motors 8.2” General Motors 8.5” 10 Bolt General Motors 8.6” 10 Bolt General Motors 12 Bolt (Passenger) General Motors 12 Bolt (Truck) General Motors 9.5” 14 Bolt General Motors 10.5” 14 Bolt Toyota 7.8” Toyota 3rd Member Requires an additional 4 oz’s This chart and the information contained herein is for reference purposes only. This information has been compiled with the utmost care, however International Lubricants, Inc. a Stellar Automotive Group Company makes no warranties and cannot be held responsible for the accuracy or reliability of this information. Always consult your vehicle owner’s manual to verify axle identification. IMPORTANT! How many tubes of LUBEGARD Limited Slip is required for your application Forward Axle Rear Axle Chevy/ GMC Chevy / GMC 1969-1977 Dana 44 1 GM 12 bolt 8.875” 12 bolt cover 1 1/2 Ton Fullsize Blazer 1977.5-1981 10 bolt 8.5” round cover 1 GM 12 bolt 8.875” 12 bolt cover 1 1/2 Ton Fullsize 1981.5-1987 10 bolt 8.5” round cover 1 10 bolt 8 5” round cover 1 K5 Blazer / Suburban 1981.5-1991 10 bolt 8.5” round cover 1 10 bolt 8 5” round cover 1 1988-1998 8.25” axle (6 lug IFS only) 1 10 bolt 8.5” round cover 1 1/2 Ton Fullsize Blazer 1995-1998 8.25” axle (6 lug IFS only) 1 14 bolt 9.5” on 4 Door X-Cab 1 1/2 Ton Fullsize Non HD 1999-2006 8.25” axle (6 lug IFS only) 1 10 bolt 8.6” round cover 1 2000-2006 8.25” axle (6 lug IFS only) 1 14 bolt 9.5” round cover 1 1/2 Ton Fullsize HD 2000-2006 9.25” axle (8 lug IFS only) 1 14 bolt 9.5” round cover 1 1969-1972 Dana 44 1 GM Eaton 10.5” Dropout 2 1973-1977.5 Dana 44 1 GM 14 Bolt 10.5” 14 bolt cover 2 GM 14 Bolt 10.5” 14 bolt cover 1977.5-1981 10 bolt 8.5” round cover 1 (with 454 motor) 2 GM 14 Bolt 9.5” 14 bolt cover 1982-1987 10 bolt 8.5” round cover 1 (with 350 motor 6.2 diesel) 1 GM 14 Bolt 9.5” 14 bolt cover 3/4 Ton Fullsize 1988-1998 9.25” axle IFS 1 (with 350 motor 6.2 diesel) 1 1988-99 8.25” axle IFS (6 Lug) 1 GM 14 Bolt 9.5” 14 bolt cover 1 GM 14 Bolt 10.5” 14 bolt cover 1988-1999 9.25” axle IFS 1 (with 454 motor) 2 GM 14 Bolt 10.5” 14 bolt cover 2000-2006 9.25” axle IFS 1 (all but 8.1L and Duramax) 2 GM 14 Bolt 11.5” 14 bolt cover 2002-2006 9.25” axle IFS 1 (with 8.1L or Duramax) 2 1977-1987 Dana 60 2 GM 14 bolt 10.5” 14 bolt cover 2 GM 14 bolt 10.5” 14 bolt cover 1988-1991 Dana 60 2 (crew cab only) 2 GM 14 8olt 11.5” 14 bolt cover 2002-2006 9.25” axle IFS 1 (with 8.1L or Duramax) 2 1 Ton Fullsize GM 14 bolt 10.5” 14 bolt cover 1988-2000 9.25” axle IFS 1 (reg and extra cab) 2 Dana 70 10 bolt cover 1977-1991 Dana 60 2 (old body style 70HD) 2 Dana 70 10 bolt cover 1988-1990 9.25” axle (8 lug IFS only) 1 (new body style 70HD-3) 2 Midsize S-10 1982-2000 7.25” axle (IFS) 1 GM 10 bolt 7.5” 10 bolt cover 1 Midsize S-10/ZR2 1995-2001 7.25” axle (IFS) 1 GM 10 bolt 8.5” 10 bolt cover 1 Colorado 2003-2006 GM 7.6 IFS 1 GM 10 bolt 8.0” 1 DIRECTIONS: Pour entire contents (4 fl. oz.) into the differential. Applications with fluid capacities over 3 liters will require using an additional 4 ounces. If necessary, remove enough gear oil to maintain proper level with supplement. Allow 20 miles of road operation for complete mixing. 2 IMPORTANT! How many tubes of LUBEGARD Limited Slip is required for your application Forward Axle Rear Axle Dodge Ramcharger & 1/2 Ton PU 1972-1993 Dana 44 (std) 1 Chry 8.25” (10 bolt cover) 1 1972-2001 Dana 44 (std) 1 Chry 9.25” (12 bolt cover) 1 1/2 Ton Fullsize 2002-2006 Chry 8” 1 Chry 9.25” (12 bolt cover) 1 1972-1996 Dana 44 (std) 1 Dana 60 (std) 2 1972-1996 Dana 44 (std) 1 Chry 9.25” (12 bolt cover) 1 3/4 Ton Fullsize 1987-1993 Dana 60 or 70 2 Dana 60 or 70 2 1994-2002 Dana 60 (std) 2 Dana 70 or 80 2 Dodge / Ford 2003-2005 AAM 9.25” 1 AAM 10.5” 1 1972-1986 Dana 60 (std) 2 Dana 70 2 1987-1993 Dana 60 w/3.08 ratio 2 Dana 70 2 1 Ton Fullsize 1994-2002 Dana 60 (std) 2 Dana 70 or 80 2 2003-2005 AAM 9.25” 1 AAM 11.5” 1 1972-1978 Dana 70 2 Dana 70 2 Chry 8.25” (10 bolt cover) 1986-1996 7.25” Chrysler 1 4 Cyl / V6 have 7.25” 1 Durango/Dakota 1997-1999 Dana 35 (std) IFS 1 Chry 9.25 (12 bolt cover) 1 2000-2006 Chry 8” 1 Chry 9.25” (12 bolt cover) 1 Ford 1967-1971 Dana 30 Front 1 Ford 9” Rear 28 Spline 1 1971.5-1977 Dana 44 Front 1 Ford 9” Rear 28 Spline 1 Bronco 1978-1979 Dana 44 Reverse 1 Ford 9” Rear 31 Spline 2 1980-1985 Dana 44 Reverse TTB 1 Ford 9” Rear 31 Spline 2 1986-1996 Dana 44 Reverse TTB 1 Ford 8.8” Rear Axle 1 1967-1972 Dana 44 Front 1 Ford 9” Rear 28 Spline 1 1973-1977 Dana 44 Front 1 Ford 9” Rear 31 Spline 2 1977.5-1979 Dana 44 Reverse 1 Ford 9” Rear 2 1980-1986 Dana 44 Reverse TTB 1 Ford 9” Rear 2 1/2 Ton Fullsize 1986-1996 Dana 44 Reverse TTB 1 Ford 8.8” Rear Axle 1 Ford 8.8” Rear Axle With 4.6L Motor 1997-2006 8.8” Reverse IFS 1 10 Bolt Cover 1 Ford 9.75” Rear Axle With 5.4L 1997-2006 8.8” Reverse IFS 1 Motor 12 Bolt Cover 2 1967-1977 Dana 44 Standard 1 Dana 60 2 1977.5-1979 Dana 44 Reverse 1 Dana 60 & 61 2 1980-1985 Dana 44 Reverse TTB 1 Dana 60 & 61 2 3/4 Ton Fullsize 1980-1985 Dana 50 Reverse TTB 1 Dana 60 & 61 2 Dana 60 1977.5-1979 Dana 60 Reverse 2 (snow fighter package) 2 Dana 44 Reverse or Dana 1986-1996 50 TTB 1 Ford 10.25” Sterling 1 DIRECTIONS: Pour entire contents (4 fl. oz.) into the differential. Applications with fluid capacities over 3 liters will require using an additional 4 ounces. If necessary, remove enough gear oil to maintain proper level with supplement. Allow 20 miles 3 of road operation for complete mixing. IMPORTANT! How many tubes of LUBEGARD Limited Slip is required for your application Forward Axle Rear Axle Dodge Ford (continued) / Hummer Jeep Ford Ramcharger & 1/2 Ton PU 1972-1993 Dana 44 (std) 1 Chry 8.25” (10 bolt cover) 1 1975.5-1979 Dana 60 Reverse 2 Dana 60 or Dana70 2 1972-2001 Dana 44 (std) 1 Chry 9.25” (12 bolt cover) 1 1/2 Ton Fullsize 1 Ton Fullsize 1980-1985 Dana 44 or Dana 50 1 Dana 60 or Dana70 2 2002-2006 Chry 8” 1 Chry 9.25” (12 bolt cover) 1 1986-1996 Dana 60 Reverse 2 Ford 10.25” Sterling 1 1972-1996 Dana 44 (std) 1 Dana 60 (std) 2 Ford 10.50” Sterling 1972-1996 Dana 44 (std) 1 Chry 9.25” (12 bolt cover) 1 1999-2001 Dana 50 1 (single rear wheel) 1 F250 3/4 Ton Fullsize 1987-1993 Dana 60 or 70 2 Dana 60 or 70 2 F350 2002-2006 Dana 60 Reverse 2 Ford 10.50” Sterling 1 Super Duty (single rear wheel) 1994-2002 Dana 60 (std) 2 Dana 70 or 80 2 1999-2006 Dana 60 Reverse 2 Dana 80 (with dual rear wheel) 2 2003-2005 AAM 9.25” 1 AAM 10.5” 1 1972-1986 Dana 60 (std) 2 Dana 70 2 Midsize 1983-1997 Dana 28 1 Ford 7.5” 28 spline 1 1987-1993 Dana 60 w/3.08 ratio 2 Dana 70 2 Dana 35 (reverse) Ford 8.8” 28 spline 1990-1997 w/l-Beam IFS 1 (4.0L & V6 Motors) 1 1 Ton Fullsize 1994-2002 Dana 60 (std) 2 Dana 70 or 80 2 Ranger / Bronco II 1998-2006 Dana 35 (std) 1 2003-2005 AAM 9.25” 1 AAM 11.5” 1 w/Control Arm IFS Dana 35 (reverse) Ford 8.8 31 spline 1972-1978 Dana 70 2 Dana 70 2 1991-1995 w/l-Beam IFS 1 (4.0L & V6 Motors) 1 1986-1996 7.25” Chrysler 1 Chry 8.25” (10 bolt cover) 1 Dana 35 (std) 4 Cyl / V6 have 7.25” 1996-2005 w/Control Arm IFS 1 Durango/Dakota Explorer 1997-1999 Dana 35 (std) IFS 1 Chry 9.25 (12 bolt cover) 1 Dana 35 (reverse) Ford 8.8 31 spline 1991-1995 w/l-Beam IFS 1 (4.0L & V6 Motors) 1 2000-2006 Chry 8” 1 Chry 9.25” (12 bolt cover) 1 Dana 35 (std) Ford 1996-2005 w/Control Arm IFS 1 1 1967-1971 Dana 30 Front 1 Ford 9” Rear 28 Spline 1 Hummer 1971.5-1977 Dana 44 Front 1 Ford 9” Rear 28 Spline 1 H1 All Amc 20 1 AMC 20 1 Bronco 1978-1979 Dana 44 Reverse 1 Ford 9” Rear 31 Spline 2 H2 2002-2006 9.25” axle IFS 1 14 bolt 9.5” round cover 1 1980-1985 Dana 44 Reverse TTB 1 Ford 9” Rear 31 Spline 2 H3 2006 GM 10 bolt 7.6” 1 GM 10 bolt 8.0” 1 1986-1996 Dana 44 Reverse TTB 1 Ford 8.8” Rear Axle 1 1967-1972 Dana 44 Front 1 Ford 9” Rear 28 Spline 1 Jeep 1973-1977 Dana 44 Front 1 Ford 9” Rear 31 Spline 2 1969-1975 Dana 30 (std) 1 Dana 44 (std) 10 bolt cover 1 1977.5-1979 Dana 44 Reverse 1 Ford 9” Rear 2 CJ5 1976-1982 Dana 30 (std) 1 AMC 20 12 bolt cover (narrow track) 1 1980-1986 Dana 44 Reverse TTB 1 Ford 9” Rear 2 1/2 Ton Fullsize AMC 20 12 bolt cover (wide-track 1986-1996 Dana 44 Reverse TTB 1 Ford 8.8” Rear Axle 1 CJ7-8 1976-1986 Dana 30 (std) 1 axle 83&up) 1 Ford 8.8” Rear Axle With 4.6L Motor CJ7 1986 Dana 30 (std) 1 Dana 44 (std) 10 bolt cover 1 1997-2006
Load more

Recommended publications
  • Off Road Unlimited Performance Steering Parts Catalog
    2010 Catalog OFF ROAD UNLIMITED YOU’VE EARNED IT. YOU DESERVE IT. WE HAVE IT! For the past 20 years, Off Road Unlimited has been manufacturing products that set new industry standards. ORU creations have graced the covers of both national and international trade publications. As recognized “experts” in the truck & SUV filed, ORU regularly appears in technical and feature articles. ORU’s employees are avid truck & SUV enthusiasts who regu larly field test their own products. Our goal is to bring you quality products, built in the USA, at a fair price. 1 NOTICE TO DEALER / CONSUMER INDEX Installation of many ORU products can change ride characteristics, 3-4 01-10 GM HD 2500-3500 4-Link Coil Over System center of gravity, and/or rollover resistance. Because of the change in 5-8 01-10 GM HD 2500-3500 HD Solid Axle Conversion Kit on/off road handling, you should familiarize yourself, and all 9-10 88-98 GM 1500-3500 Solid Axle Conversion Kit operators of the vehicle with the unique handling (32.5 Spring Pad width) characteristics associated with it. Extreme care should be taken when 11-12 88-98 GM 1500-3500 Solid Axle Conversion Kit operating the vehicle to prevent possible loss of control or rollover that (36.5 Spring Pad width) could result in serious injury or death. The user is ulitmately responsi- 13-14 88-98 GM 1500 2wd Solid Axle Conversion Kit ble for the safe operation of the vehicle and compliance with any indi- 15 Chevy/GMC Leveling Kits vidual state laws that may apply to it modification.
    [Show full text]
  • Dana Spicer Light Axle General Information
    XGI August 2014 Supersedes XGI Dated May 2006 Light Vehicle Axle General Information Now also including: The Ultimate Dana 60, Chromoly Axle Shafts, Performance Diff Cover Gaskets, Spools, All-Makes Ring and Pinions, All-Makes Axle Shafts, and more. Product pictured is intended to be a representation of product category. SAFETY INFORMATION WARNING - Failure to follow these instructions could affect vehicle performance and/or safety and result in personal injury or death. • Do not convert or alter Spicer axles except in accordance with vehicle manufacturer's instructions. Spicer axles are designed to meet OEM vehicle manufacturer's design and performance specifications. Improper conversion or alteration of these axles can damage the axles and/or other vehicle systems. Contact the OEM manufacturer for specific directions and guidelines. • Do not change axle gear ratios on vehicles with anti-lock braking systems except in accordance with the vehicle manufacturer's instructions. Vehicles with anti-lock braking systems may utilize sensors and tone rings within the axle housings to ensure the functioning of the anti-lock brakes. Improperly changing the axle ratios may defeat the anti-lock braking system. If changing axle ratios will require changing the location of the tone ring on the ring gear flange relative to the location of the sensor in the axle housing, contact the OEM manufacturer for specific directions and guidelines. • Do not reuse or substitute ring gear bolts. If you reuse a ring gear bolt or substitute an inferior quality bolt, the bolt may loosen or back out of its threaded hole, causing severe damage to the axle gears and other components and possibly resulting in a sudden "locking up" of the axle and loss of control of the vehicle.
    [Show full text]
  • North American Application Chart
    NORTH AMERICAN APPLICATION CHART AUGUST 2008 This listing covers most common North American Chevrolet / GMC / Hummer 1 applications but is not a complete list of all possible Chrysler / Jeep 2 applications. For South or Dodge 3 Central American, Ford 4 applications, or other Isuzu 5 international applications not referred to in this listing, Land Rover 5 please refer to our Australian Mazda 6 & International Application Mitsubishi 6 Chart, or contact ARB or your local ARB stockist. Model Nissan 6 years and names may vary Suzuki 7 greatly depending on point of Toyota / Lexus 7 sale. Use axle shaft spline count and / or ring & pinion Performance Applications 8 ratio to distinguish between Differential Covers 8 similar models where Applications by part number 9 possible. 4X4 ACCESSORIES Page 1 Chevrolet / GMC / Hummer CHEVROLET / GMC / HUMMER Shaft Shaft ARB Vehicle/Model Axle Loc'n Year Description Ratio Diameter Spline Part No. 10/1500 Series, C, G, K, Front To 1980 Dana M44, 3600lb 33.3 (1.31") 30 3.92 & UP RD1166 P, Blazer, Jimmy, 3.73 & DN RD117 Yukon, Suburban1, 1977-89 GM 10 bolt 30.5 (1.20") 28 2.73 & UP RD832 Vans Rear 1989-96 GM 10 bolt, 8.5" dia. RG, semi floating 33.3 (1.31") 30 2.73 & UP RD842 1982-89 GM 10 bolt, 8.5" dia. RG, semi floating 30.5 (1.20") 28 2.73 & UP RD832 1982 on GM 14 bolt, 9.5" dia. RG, semi floating 34.8 (1.37") 33 All RD40 To 1982 GM 12 bolt, 8.875" dia.
    [Show full text]
  • Center of U-Joint Cap S
    "Front" Axle Shaft Ordering Defined 1250 E. Piper Ct. Meridian, Idaho 83642 Phone: 503.257.6604 Fax 503.253.6564 Front End Type For inner shafts, this is simply the make and model of the front end you are working on. Examples of this are Dana 44, Dana 60, or hybrid Ford 9" 31 spline, D50 30 spline [which is very weak], etc... For outer shafts this is simply the make of the spindle -- if known. Examples of this are Ford, GM, Jeep, or Dodge/ Chrysler. Hybrid custom front end This section is only filled out if you are building a custom front end using the center from one housing and the spindles/ knuckles from another. An examples of this is: A Ford 9" or 14 bolt center & Dana 60 spindles/knuckles, or an aftermarket housing center and spindle/knuckle combo kit, etc... S: (Spline count) Make/Model Splines Spline Dia. Seal Diameter This is the number of splines the axle has. Either count them Dana 30 27 1.167 1.185 or measure the diameter of the splines with a dial caliper or Dana 35 27 1.167 1.315 micrometer. Use the reference chart of some common spline GM Corporate 28 1.205 1.315 and seal combinations to identify your spline count. Also list in the notes the type of differential or spool you will Dana 44 / GM Corp 30 1.290 1.315 be using, either factory or aftermarket. If using an aftermar- GM 14 bolt [Hybrid] 30 1.530 1.562 ket carrier or full spool, list the manufacturer (as some use Dana 50 [Not good] 30 1.290 1.562 different pressure angles for their splines as well as slightly Ford 9" [Hybrid] 31 1.325 1.325 different end of spline dimensions).
    [Show full text]
  • Table of Contents Chrysler® / Dodge®
    Richmond Gear Ring & Pinion Application Guide Table of Contents Chrysler® / Dodge® - - - - - - - - - 4 Corvette® / Dana®- - - - - - - - - - 4 Ford®- - - - - - - - - - - - - -10 Gear Ratio Chart - - - - - - - - - - - 12- - - GM® - - - - - - - - - - - - - - - - - - - -15 Nissan®- - - - - - - - - - - - - 19 Toyota®- - - - - - - - - - - - - 19 Richmond Gear Warranty - - - - - - - - - - - - - - - - - -22 Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our performance products are the result of a continuous research and development program com- bined with state-of-the-art manufacturing capabilities at our plants worldwide. For over 80 years, the Double Diamond has signified the highest quality products in the racing industry! Our complete line of Richmond Gear performance products ranges from high performance ring-and- pinion sets for serious street and racing applications to torque-hungry manual transmission, and components for on and off-road use. We also offer full ring and pinion installation kits and instructional videos. Engineered to perform faster and be more reliable, Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. Winners Run Richmond! Parts listed in this catalog are not necessarily manufactured by the original equipment manufacturer and any reference to the trademarks or part numbers of others are for cross reference informational purposes only. The photos provided herein are provided only for illustrative purposes. The actual products supplied may differ. The Excel by Richmond trademarks of others referred to herein are owned by their respective companies and are not affiliated in any way with Midwest Truck & Auto Parts, Inc.™, Richmond Gear® By providing high-quality OEM replacement gears for your vehicle, and Excel by Richmond®. These divisions are the registered or pending trademarks Richmond’s Excel line provides Richmond quality at affordable prices.
    [Show full text]
  • Hours of Operation Method of Payment Ordering Our
    WELCOME TO JEFF’S BRONCO GRAVEYARD INC. Jeff’s Bronco Graveyard Inc. has been serving the Bronco community for nearly 20 years. During that time we have steadily grown to become one of the largest sellers of Bronco parts and accessories in the country. We attribute this steady growth to our continued commitment to giving you the best possible price, quality and service. We guarantee the best prices in the industry, and to minimize down time, most orders are shipped the day they are placed. Our recent expansion boasts a 26,000 sq. ft. warehouse to help us expedite your order. We thank you for all your continued support and look forward to serving your future Bronco needs. Hours of operation Mon. - Wed: 9:00 a.m.- 6:00 p.m.(EST) Thurs. - Friday: 9:00 a.m.- 5:00 p.m.(EST) Our store never closes at www.broncograveyard.com Ordering Orders are accepted by phone, fax, mail, or on the web at our secure website: www.broncograveyard.com Returns Phone: (248) 437-5060 All returns to Jeff’s Bronco Graveyard Inc. must be accom- (248) 486-1760 panied by an RMA number. Please see following page for a complete description of our return policy Fax: (248) 437-9354 Core returns Address: Jeff’s Bronco Graveyard All cores must be returned within 90 days for core credit, and be 7843 Lochlin Dr. accompanied by a copy of original receipt. Brighton, MI 48116 Method of payment Damaged shipments JBG aceepts Visa, Mastercard, American Express, Discover In the event of receiving a damaged shipment, please notify and Debit cards.
    [Show full text]
  • LIMITED SLIP DIFFERENTIAL Identification and Application Chart
    LIMITED SLIP DIFFERENTIAL Identification and Application Chart For use in all clutch-type limited slip differentials Eliminate differential chatter and noise Reduce differential oil temperatures Extend clutch pack and equipment life Part #42581 LUBEGARD® Multi-Vehicle Limited Slip Supplement can be used in place of OE friction modifiers (for example Ford, Chrys- ler, GM, etc) for limited slip differentials. IMPORTANT! Please be sure to adequately research technical resources such as your vehicle’s manual to determine the type of assembly for your application. LUBEGARD Limited Slip Sup- plement is only for use in clutch-type limited slip differentials. INTERNATIONAL LUBRICANTS, INC. a STELLAR AUTOMOTIVE GROUP COMPANY 7930 Occidental South Seattle, WA 98108 206-762-5343 800-333-LUBE (5823) ©2016 ILI. All trademarks are property of their respective owners. www.Lubegard.com IMPORTANT! How many bottles of LUBEGARD® Limited Slip Supplement is required for your application? LG 4 oz. LG 4 oz. APPLICATION Year Rear LS Differential Treat Front Differential Treat Buick Buick 73-79 GM 8.5" & 8.625" 1 N/A N/A Buick Grand National 77-87 GM 8.5" & 8.625" 1 N/A N/A Buick Omega 73-79 GM 8.5" & 8.625" 1 N/A N/A Buick Regal 73-77 GM 8.5" & 8.625" 1 N/A N/A Cadilac Cadilac 80-90 GM 7.5" & 7.62" 1 N/A N/A Cadilac 77-83 GM 8.75" & 8.875" 1 N/A N/A Cadilac Fleetwood 77-79 GM 8.75" & 8.875" 1 N/A N/A Cadilac Fleetwood Limo 90 GM 8.5" & 8.625" 1 N/A N/A Cadilac Seville 77-79 GM 8.5" & 8.625" 1 N/A N/A Chevrolet Buick / Cadilac Chevrolet Chevrolet 1/2 & 3/4
    [Show full text]
  • ARB Corporation Limited
    INTERNATIONAL VEHICLE APPLICATION GUIDE Copyright © by ARB Corporation Limited. All rights reserved. All text, images, graphics and other materials herein are subject to the copyrights and other intellectual property rights of ARB Corporation Limited. These Materials may not be copied for commercial use or distribution, nor may these materials be modified or reposted to other sites without the express written consent of ARB Corporation Limited. No Liability is assumed for damages resulting in the use of the information contained herein. ARB Air Locker Air Operated Locking Differentials and Air Locker are trademarks of ARB Corporation Limited. Other product names used herein are for identification purposes only and may be trademarks of their respective AIR OPERATED LOCKING DIFFERENTIALS INTERNATIONAL VEHICLE APPLICATION CHART OCTOBER 2016 This listing covers most Chevrolet / GMC / Hummer 1 known Australian and Chrysler / Jeep 2 International applications but is not a complete list of all Dodge 3 possible applications globally. Ford 4 Holden 5 For applications not Hyundai 5 specifically referred to in this Isuzu 5 listing, please contact ARB or Land Rover 6 your local ARB stockist. Mazda 6 Model years and names may vary greatly depending on Mitsubishi 7 point of sale. Use axle shaft Nissan 8 spline count and / or ring & Santana 9 pinion ratio to distinguish Ssangyong 9 between similar models Suzuki 9 where possible. Toyota / Lexus 10 Volkswagen 10 Performance Applications 11 Differential Covers 11 Air Compressors 11 Applications By Part Number 12 Page 1 Chevrolet / GMC / Hummer CHEVROLET / GMC / HUMMER Vehicle/Model Axle Loc'n Year Description Shaft Shaft Ratio ARB Diameter Spline Part No.
    [Show full text]
  • The Power Transfer Experts the Only Aftermarket Differentials Made In
    THE POWER TRANSFER EXPERTS THE ONLY AFTERMARKET DIFFERENTIALS MADE IN AMERICA Table Of Contents 03 Introduction to Auburn Gear 20 Ford 7-1/2” 10 Bolt & Ford 8” 10 Bolt 04 Auburn Gear History 21 Ford 8.8” 10 Bolt & Ford 9” 10 Bolt Ford 9-3/4” 12 Bolt & 05 Grip-N-Loc® Overview 22 Ford 10-1/4” & 10-1/2” 12 Bolt GM 7-1/2” & 7-5/8” 10 Bolt & 06 Select-A-loc® Overview 23 GM 7-1/2” & 7-5/8” 10 Bolt Chevy 8.2” 10 Bolt & 07 Auburn Gear OEM History/4 Pinion Differentials 24 Buick - Olds - Pontiac 8.2” 10 Bolt GM 8.2”/8.4” 10 Bolt 1955-1964 Chevy & 08 Rear Axle ID: AMC, Chrysler, Dana, Ford 25 Corvette 10 Bolt 1963-1979 & Gen 5 Camaro 218mm 10 Bolt 09 Rear Axle ID: GM 26 GM 8.5” & 8.6” 10 Bolt 10 Rear Axle ID: Toyota and Nissan 27 GM 8-7/8” 12 Bolt - Car 11 AMC 20, 12 Bolt GM 8-7/8” 12 Bolt - Truck & GM 11-1/2” 28 2500/3500 Single and Dual Wheel Truck Chrysler 8-1/4” & 8-3/8” 10 Bolt 12 Chrysler 8-3/4” 10 Bolt 29 Toyota 8” 10 Bolt & Toyota 8.4” 10 Bolt 13 Chrysler 9-1/4” 12 Bolt Toyota 9.5” 12 Bolt, 30 Toyota 10.5” 12 Bolt & Land Cruiser 12 Bolt Chrysler 9-1/4” 12 Bolt “ZF Rear” 14 Ram HD 2500/3500 Truck 11-1/2”, 14 Bolt Toyota Sequoia & 31 Nissan Titan 10 Bolt 15 Dana 30 & 35 32 Differential Service Kits 16 Dana 44 33 Select-A-Loc® Service Kits 17 Dana Super 44 & 50 34 Tire Chart 18 Dana 60 35-37 FAQs 19 Dana 70 & 80 2 AUBURN GEAR STANDS OUT FROM EVERY AFERMARKET DIFFERENTIAL BRAND IN FOUR WAYS: 1.
    [Show full text]
  • Nissan Applications, Light Axle Parts
    X510- 10 Light Axle Parts for Nissan Applications August 2014 The Spicer X510-10 is a comprehensive catalog that delivers the information you need about light axle parts for Nissan applications — all in one convenient place. X510-10 CONTENTS How to Use This Catalog .......................................... 2 General Information .................................................. 4 Axle Kits ..................................................................... 6 Dana 205™ Front Axles for 4 x 4 Exploded View ......................................................... 8 Parts Listing .............................................................. 9 Bill of Material Table ................................................ 10 Variable Parts Table ................................................ 10 Dana Super 44™ /226 Rear Axles Exploded View ........................................................ 12 Parts Listing ............................................................ 13 Bill of Material Table ................................................ 14 Variable Parts Table ................................................ 16 Bearing Adjustment Shim Table ............................. 19 1 X510-10 How to Use This Catalog This catalog contains applications and part listings for front and rear axles which fit Nissan vehicles from model years 2003 and newer. The data in this publication is arranged in numerical order by model for front axles and then for rear axles. Each model contains the following three sections as appropriate: • Parts Listing and Exploded
    [Show full text]
  • Dana Crate Axles Specs
    Know What You re Getting. Get What You Know. MADE IN USA! There are many imitations, but only one original. The genuine Dana Crate Axle™ Program now delivers the peace of mind that comes from getting genuine Dana axles through our network of authorized Dana Crate Axle™ specialists. crate axles Spicer ® Light Axle Ratings: Ring Gear Size Torque limit @ input GAWR GVW GCW Model Location inch ft.-lbs. lbs. lbs. lbs. Dana 30™ Front 7.30 1450 2800 5700 8000 Dana 44™ Rear 8.90 1930 3570 5700 8500 Dana 44™ Front 8.50 1930 3360 5700 8000 Dana 60™ Rear 9.75 2400 5760 8200 17100 Dana 60™ Front 10.10 2785 7350 16000 30000 Dana 70™ Rear 10.50 2600 8580 9900 18000 Dana 70™ Front 10.75 3450 8400 19500 26000 Dana 80™ Rear 11.25 3000 10100 14000 30000 Note: These ratings are general guidelines. Actual load rating and torque limit will vary by application and duty cycle. Planned Ratios Ratios: 30 Front 44 Rear 44 Front 60 Rear 60 Front 70 Rear 70 Front 80 Rear 3.73 X A X A X X X X 4.10 X A X A X X X X 4.56 X X X X X X X X 4.88 X X X X X X X X 5.13 X X X X X X X X A = Gear set is available. X = Gear set is planned for future release. GAWR is Gross Axle Weight Rating. Maximum distributed weight an axle can support. GVW is Gross Vehicle Weight Rating.
    [Show full text]
  • X510-10 April 2013
    X510-10 April 2013 Light Axle Parts for Nissan Applications The Spicer X510-10 is a comprehensive catalog that delivers the information you need about light axle parts for Nissan applications — all in one convenient place. X510-10 CONTENTS How to Use This Catalog .......................................... 2 General Information .................................................. 4 Axle Kits ..................................................................... 6 Dana 205™ Front Axles for 4 x 4 Exploded View ......................................................... 8 Parts Listing .............................................................. 9 Bill of Material Table................................................ 10 Variable Parts Table ................................................ 10 Dana Super 44™ /226 Rear Axles Exploded View ........................................................ 12 Parts Listing ............................................................ 13 Bill of Material Table................................................ 14 Variable Parts Table ................................................ 16 Bearing Adjustment Shim Table ............................. 19 1 X510-10 How to Use This Catalog This catalog contains applications and part listings for front and rear axles which fit Nissan vehicles from model years 2003 and newer. The data in this publication is arranged in numerical order by model for front axles and then for rear axles. Each model contains the following three sections as appropriate: • Parts Listing and Exploded
    [Show full text]