Airport Solutions construction chemicals Material Presentation construction chemicals

Teknopoliderz 2K Polyurethane Joint Filler be half size of width. Minimum joint fill depth should be 1 cm • Can be applied in electrical cable joint • Military fields • Garage flors and car washing bays, • Underground garages, • Car parks (where elastic or plastic insulation exists), • Connection joints of bituminous coverings to concrete covering sand concrete objects, • Cracks on the asphalt and concrete roads

Feature and Benefits: • Polyurethane based, solvent free, • Teknopoliderz 2K has the technical specification characters of standards TS 5926 EN 14188 -2, • American Federal Specification SS-S- 00200D and British Standard 5212 • Indoor and outdoor application , TS 5926 DIN EN 14188-2 STANDARD • Easy to apply, • Extremely flexible, • Resistance to UV Description: • Resistant against weathering Jet-Fuel and oil resistant, two components, self • Good temporary resistance to a wide variety levelling, elastomeric, cold applied ,tar of solutions nd fuel, jet fuel and oil, modified polyurethane based joint filler

Uses: Teknopoliderz 2K provides the water insulation between the concrete elements. It is a cold applied sealant, which is resistant to jet fuel, fuel and motor fuel oils and used in the related fields such as:

• Runways, parking ways and garages at , • Flooring and connection joins for over ground fuel storage depot sand loading bays for fuel oil and motor fuel oils, • It used concrete, surface hardener, asphalt, natural stone, mosaic and sheet metal surfaces with suitable primer • It is used between Asphalt-Asphalt, Asphalt - Concrete, Concrete-Concrete. Depth should

Teknopoliderz 2K construction chemicals

Substrate and Ambient Condition +5°C - +50°C

Cleaning of Tools Clean all tools and application equipment with TeknoTiner immediately after use. Hardened/cured material can only be mechanically removed

Pot Life Approx 35-45 min at 20°C

Application and Limitation • Foreign material should not be added • Do not apply under the rain

Substrate Quality All surfaces must be clean, dry and free from all loosely adhering particle. Correct joints depths can be established by inserting polyethylene foam in to the joint. Where joints have been formed with the fiber filler board, this must be raked back to the required depth and a bond breaker tape inserted. Protect surfaces with masking tape.

Priming: Use Teknobond 110 Primer, for all cement bound building materials, exposed brick work, asbestos cement, natural and artificial stone work, polyester and hard PVC.

Mixing: Using a low speed drill (500 -800 rpm) thoroughly mix the contents of component A, before adding component B. After adding, mixing together for not less than 3 min. untill a smooth even consistency is achieved.

Application Tools Joint Filler Machine , Joint Filler Application Gun, Masking Tape

Teknopoliderz 2K construction chemicals

Technical Data

Type: Liquid, Polyurethane and ifnecessary Tar added

Color: Black, Grey, Redand White

Density: 1,30 ± 0,05 kg/lt.

Pot Life: 35-45 minutes +20oC Hardness: 20±5 Shore A

Volume Solids ( % ) 100 Permissible Deformaton ± %25

Applicaon T mperature: Between +5 oC and +50oC degrees

Temperature Resistance Up To 70 °C

Elongaon: ~ 600% (at break)

Elastc Recıvery ( % ) >% 90 Curing Rate: Depends on temperatureapp 3 -12 Hours

Primer (Teknobond 110): 15 kg.

Standard According to TS 5926 EN 14188-2

Packing 10 kg Set

Teknopoliderz 2K SAFETY DATA SHEET Product Name: TEKNOPOLIDERZ 2K COMPONT A Date of Issue:10/12/2018

MATERIAL SAFETY DATA SHEET TEKNOPOLIDERZ 2K COMPONENT A

1. IDENTIFICATION OF THE PRODUCT AND THE PRODUCER

Product : Teknopoliderz 2K Product Description : Base component of two part pitch free polyurethane sealant. Producer/Suplier : Tekno Yapı Kimyasalları San. Tic. A.Ş Address : Istanbul Deri Organize San. Bolgesi Gergef Sok. No : 6Tuzla / Istanbul/ TURKIYE Telephone : +90216 4291000 Fax :+ 90216 4290200

2. COMPOSITION AND INFORMATION OF THE INGREDIENTS

Composition: polyester polyol, inert fillers, pigment, chlorinated paraffin, plasticiser, mdi.This product contains ingredients classified as hazardous. However, they are NOT present in sufficient quantities to warrant classifying the product as hazardous. All constituents of this product are listed in EINECS (European Inventory of Existing Commercial Chemical Substances) or ELINCS (European List of New Chemical Substances) or are exempt. Refer to Section 8 for Occupational Exposure Limits.

3. HAZARD IDENTIFICATION

No significant hazard.

4. FIRST AID MEASUREMENTS

Eyes : Irrigate immediately with copious quantities of water for several minutes. Obtain medical attention if irritation persists. Skin : Wash thoroughly with soap and water or suitable skin cleanser as soon as possible. Inhalation: Remove from exposure. Ingestion : Do NOT induce vomiting. Obtain medical attention. Beware of aspiration if vomiting occurs.

5. FIRE PREVENTION

Suitable Extinguishing Media: Carbon dioxide, powder, foam or water fog - Do not use water jets.Special Exposure Hazards: Toxic fumes, Chlorine compounds including hydrogen chloride. Special Protective Equipment: Self-contained breathing apparatus.

6. PRODEDURE IN CASE OF SPILLAGE OR LEAKAGE

Personal Precautions: Wear suitable protective clothing, gloves and eye/face protection.Environmental Precautions: Prevent entry into drains, sewers and water courses.Decontamination Procedures: Soak up with inert absorbent or contain and remove by best available means.Gather into containers. Dispose of as waste. SAFETY DATA SHEET Product Name: TEKNOPOLIDERZ 2K COMPONT A Date of Issue:10/12/2018

7. HANDLING AND STORAGE

Handling: Avoid skin and eye contact. Use only in well ventilated areas Storage: Store in cool, dry area.

8. PREVENTION OF EXPOSURE

Occupational Exposure Limits:- None assigned. Engineering Control Measures: Use only in well ventilated areas. Personal Protective Equipment: Avoid skin and eye contact. Safety glasses / Goggles. Impervious gloves (eg PVC). Change contaminated clothing and clean before re-use.

9. PHYSICAL AND CHEMICAL PROPERTIES

Physical State: Viscous liquid. Colour: Black. Odour: Slight/faint. Boiling Point/Range (°C): > 200 Flash Point (closed, °C): >140 Autoflammability (°C): Not determined. Oxidising Properties: Not applicable. Vapour Pressure (kPa at 20°C): Not determined. Relative Density (at 20°C): 1.40 Water Solubility: Insoluble.

10. STABILITY AND REACTIVITY

Stability: Stable if used as directed. Conditions to Avoid: Temperatures (ºC) above 40. Materials to Avoid: Contamination by water. Strong oxidising agents. Hazardous Decomposition Products: Thermal decomposition:- Toxic fumes. Oxides of carbon. Chlorinecompounds including hydrogen chloride.

11. TOXICOLOGICAL INFORMATION

The following toxicological assessment is based on a knowledge of the toxicity of the product's components. Health Effects On Eyes: May cause transient irritation. On Skin: Unlikely to irritate on brief or occasional exposure. By Inhalation: Low volatility makes inhalation unlikely at ambient temperatures. By Ingestion: May cause nausea, vomiting and diarrhoea. SAFETY DATA SHEET Product Name: TEKNOPOLIDERZ 2K COMPONT A Date of Issue:10/12/2018

12. ECOLOGICAL INFORMATION

Environmental Assessment: When used and disposed of as intended, no adverse environmental effects are foreseen. Mobility: Insoluble in water. Persistence and Degradability: Not readily biodegradable. Bioaccumulative Potential: Not determined. Ecotoxicity: Not determined.

13. WASTE DISPOSAL M ETHOD

Disposal must be in accordance with local and national legislation. Unused Product: Dispose of through an authorised waste contractor to a licensed site.Used/Contaminated Product: As for Unused product. Packaging: The method of disposal must be acceptable to the local authority.

14. INFORMATION FOR TRANSPORT

This product is NOT classified as dangerous for transport.

15. STATUTORY INFORMATION

Hazard Label Data:- This product is NOT classified as dangerous for supply in the . Safety Phrases: In case of contact with eyes, rinse immediately with plenty of water and seek medical advice Wear suitable gloves and eye/face protection. EC Directives: Dangerous Substances Directive, 67/548/EEC and adaptations. Dangerous Preparations Directive, 88/379/EEC. Safety Data Sheets Directive, 91/155/EEC. Statutory Instruments: Chemicals (Hazard Information and Packaging for Supply) (Amendment) Regs. 1996 (SI 1092). Control of Substances Hazardous to Health Regs. 1994 (SI 3246). Environmental Protection Act 1990. Codes of Practice: Waste Management. The Duty of Care. The above publications are available from HMSO

16. OTHER INFORMATION First Issue Date :01/01/2009

Also refer to the Safety Data Sheet(s) for information on other components of this product. The data and advice given apply when the product is used for the stated application or applications. The product is not sold as suitable for any other application. Use of the product for applications other than as stated in this sheet may give rise to risks not mentioned in this SAFETY DATA SHEET Product Name: TEKNOPOLIDERZ 2K COMPONT A Date of Issue:10/12/2018 sheet. The product should not be used other than for the stated application or applications without seeking advice from TEKNO. If this product has been purchased for supply to a third party for use at work, it is the purchaser's duty to take all necessary steps to secure that any person handling or using the product is provided with the information in this sheet. It is the responsibility and duty of the employer to inform employees and others who may be affected of any hazards described in this sheet and of any precautions which should be taken. This sheet does not constitute or substitute for the users own assessment of workplace risk, as required by other health and safety legislation. SAFETY DATA SHEET Product Name: TEKNOPOLIDERZ 2K COMPONENT B Date of Issue:05/11/2018

MATERIAL SAFETY DATA SHEET TEKNOPOLIDERZ 2K COMPONENT B

1. IDENTIFICATION OF THE PRODUCT AND THE PRODUCER Product :TEKNOPOLIDERZ 2K–PART B Producer :TEKNO YAPI KİMYASALLARI SAN. VE TİC. A.Ş. Address : Istanbul Deri Organize San. Bolgesi Gergef Sok. No : 6 Tuzla / Istanbul/ TURKIYE Telephone : +90216 4291000 Fax :+ 90216 4290200 2. COMPOSITION AND INFORMATION OF THE INGREDIENTS Preparation - Hazardous ingredients ( Europe ) Component Diphenylmethandiisocyanate CAS/EINECS 101-68-8 Concentration 50.00% - 100.00% Classification Xn Risk Phrases R20, R36/37/38,R42/43

3. HAZARD IDENTIFICATION Hazard Category: Harmful by inhalation. Irritating to eyes, respiratory system and skin.May cause sensitisation by inhalation and skin contact.

4. FIRST AID MEASUREMENTS Inhalation: Remove from exposure. In cases of possible respiratory irritation or if feeling unwell in cases of prolonged exposure,obtain medical attention.

Skin contact: If skin or hair contact occurs, remove contaminated clothing and flush skin and hair with running water. Solvents should not be used to clean skin because they may increase the penetration of the material.In case of symptoms seek medical assistance.

Eye contact: Immediately flood the eye with plenty of water for at least 15 minutes, holding the eye open. Obtain medical attention urgently.

Ingestion: Do not induce vomiting.Wash out mouth with water. Obtain medical attention.

5. FIRE PREVENTION Suitable extinguishing media Alcohol resistant foam, CO2, powders, water spray.

Unsuitable extinguishing media Waterjet.

Special Hazards of Product SAFETY DATA SHEET Product Name: TEKNOPOLIDERZ 2K COMPONENT B Date of Issue:05/11/2018

Thermal decomposition or burning may release oxides of carbon, nitrogen and other toxic gases and vapours.

Special protective equipment Wear full protective clothing and self-contained breathing apparatus.

6. PRODEDURE IN CASE OF SPILLAGE OR LEAKAGE Personal precautions Wear appropriate protective clothing.

Environmental precautions Do not empty into drains. If the product contaminates lakes, rivers or sewages, inform appropriate authorities in accordance with local regulations.

Methods for cleaning up/collecting Contain and absorb using earth, sand or other inert material. Transfer into suitable containers for recovery or disposal.

7. HANDLING AND STORAGE Safe handling: Use in well ventilated area. Avoid contact with water or moist air. Exposure by inhalation or skin contact should be minimised by good Industrial Hygenie practices.

Storage: Avoid contact with eyes, skin and clothing. Storage area should be: cool. dry. Storage temperature should be controlled to between 5 and 25 °C. Store in the original container securely closed . Keep away from Foodstuffs

8. PREVENTION OF EXPOSURE Occupational Exposure Limits – GB Diphenylmethandiisocyanate UK EH40: MEL 0.07mg/m3 15min STEL. UK EH40: MEL 0.02mg/m3 8h TWA. Engineering Control Measures :Use of the basic principles of Industrial Hygiene will enable this material to be used safely.

Respiratory Protection :Respiratory protection not normally required. Hand Protection :Wear suitable impervious gloves. (butyl / nitrile type ) The insides of gloves must be kept scrupulously clean. Eye Protection :Chemical goggles.

9. PHYSICAL AND CHEMICAL PROPERTIES Physical State Liquid. Color Straw - Colourless. Odor Characteristic. Flash Point °C Exceeds 200. Solubility - Water Insoluble. SAFETY DATA SHEET Product Name: TEKNOPOLIDERZ 2K COMPONENT B Date of Issue:05/11/2018

(reacts with water to form solid) Density (kg/m3) Approx. 1200 at 20 °C. Viscosity (at 20°C) 300 at 20 °C. (measured as mPa.s)

10. STABILITY AND REACTIVITY Stable under normal conditions. Polymerisation will continue if exposed to: water. Extremes of temperature. Exposure to water or moisture. Conditions to avoid Polymerisation will continue if exposed to: water. Heating may produce: oxides of carbon. oxides of nitrogen. acrid smoke and irritating fumes.

11. TOXICOLOGICAL INFORMATION Acute toxicity Low order of acute toxicity. Eye irritation Irritating to the eyes. Frequent skin contact may cause irritation and defatting due to the solvent content. Skin irritation

12. ECOLOGICAL INFORMATION Mobility The product is insoluble in water. Persistence/degradability The product is expected to be not readily biodegradable. Ecotoxicity The product may be harmful to aquatic organisms.Ecotoxical effects

13. WASTE DISPOSAL METHOD

Product Disposal Dispose of as Special Waste. Container Disposal Arrange for disposal via a licensed waste contractor Dispose of containers with care. Empty containers may contain hazardous residues. Empty packaging should be removed by a licensed waste Contractor.

14. INFORMATION FOR TRANSPORT ADR/RID : Number Not classified for Road/Rail Transport IMDG :Proper shipping name Not classified for Sea Transport IATA :Proper shipping name Not classified for Air Transport

15. STATUTORY INFORMATION Label Requirements Harmful Risk Phrases Harmful by inhalation. Irritating to eyes, respiratory system and skin. May cause sensitisation by inhalation and skin contact.

16. OTHER INFORMATION First Issue Date :01/01/2009 Also refer to the Safety Data Sheet(s) for information on other components of this product. The data and advice given apply when the product is used for the stated application or applications. The product is not sold as suitable for any other application. Use of the product for applications other than as stated in this sheet may give rise to risks not mentioned in this SAFETY DATA SHEET Product Name: TEKNOPOLIDERZ 2K COMPONENT B Date of Issue:05/11/2018

sheet. The product should not be used other than for the stated application or applications without seeking advice from TEKNO. If this product has been purchased for supply to a third party for use at work, it is the purchaser's duty to take all necessary steps to secure that any person handling or using the product is provided with the information in this sheet. It is the responsibility and duty of the employer to inform employees and others who may be affected of any hazards described in this sheet and of any precautions which should be taken. This sheet does not constitute or substitute for the users own assessment of workplace risk, as required by other health and safety legislation.

construction chemicals construction chemicals construction chemicals construction chemicals

construction chemicals

OUR REFERENCES

Georgia Tbilisi , Georgia TAV Skopje Airport, Macedonia Jeddah King Abdulaziz Internaonal Airport , Saudia Riyadh Airport - King Khalid Internaonal Airport,, Saudia Enfidha–Hammamet Internaonal Airport -Tunusia Ashgabat Internaonal Airport, Turkmenistan Algiers Houari Boumediene Airport, Algeria Istanbul Atatürk Airport Istanbul 3rd Airport Istanbul Sabiha Gökçen Airport Bodrum Airport Adnan Menderes Airport Adana Airport Airport Elazığ Airport Esenboğa Airport Airport Gaziantep Airport Airport Diyarbakır Airport 1st Air Force Command 2nd Air Force Command 3rd Air Force Command 8th Air Force Command Balıkesir Air Force Command Bandırma Air Force Command Akhisar Air Force Command Sinop Airport Gökçeada Airport Van Airport Malatya Airport Kars Airport Adana - İncirlik Air Base THY Kargo, İnşaat ve Teknik A.Ş Tav Alanya Gazipaşa Airport Balıkesir – Edremit Airport Samsun Airport Bingöl Airport Urfa Airport Hakkari Airport Iğdır Airport Nevşehir Kapadokya Airport Kahramanmaraş Airport REFERANSLAR HAVALİMANI REFERANSLAR

Makyol İnşaat (Makyol Eko ortaklığı, yeşilköy) Ordu Havalimanı- Orgi projesi ( Cengiz-İçtaş )

Atatürk Havalimanı ( Makyol İnşaat, Tav Havalimanları İşletmeciliği, DHMİ San Alma)

Bodrum Havalimanı ( Gena İnşaat)

Adnan Menderes Havalimanı ( Tav)

Adana Havalimanı ( DHMİ )

Sabiha Gökçen Havalimanı ( YDA, Gena İnşaat, Atlas İnşaat, YBT İnşaat)

Dalaman Havalimanı ( YDA, DHMİ San Alma, Askeri ortak pist, YDA İşletme)

Elazığ Havalimanı ( DHMİ San Alma, EMT-Doğan Mühendislik, Günay İnşaat)

Esenboğa Havalimanı( Tav , EMT-DOĞAN MÜHENDİSLİK )

Erzincan Havalimanı

Mardin Havalimanı ( İkiz İnşaat)

Gaziantep Havalimanı (DHMİ San Alma, İkiz İnşaat, Gena İnşaat, Yek İnşaat)

Konya Havalimanı (DHMİ San Alma, Askeriye ortak pist kullanım, Gena İnşaat)

Diyarbakır Havalimanı( YDA, Kayaoğlu İnşaat, Askeriye ortak pist)

8.ana jet üs komutanlığı

3.ana jet üs komutanlığı

2.ana jet üs komutanlığı

3. Havalimanı ( İGA, MNG –Esmas, Kalyon İnşaat –THY-Bozacıyapı) Balıkesir hava üs komutanlığı

Bandırma hava üs komutanlığı

Akhisar hava üs komutanlığı

Hava kuvvetleri Komutanlığı

Sinop Havalimanı (DHMİ San Alma, Arda Mühendislik, EMT-Doğan Mühendislik)

Gökçeada Havalimanı ( Turan İnşaat, DHMİ San Alma)

Van Havalimanı(DHMİ San Alma)

Isparta Havalimanı(DHMİ San Alma)

Malatya Havalimanı ( Yörük İnşaat)

Kars Havalimanı ( Sarıdağlar İnşaat, Ermit İnşaat, DHMİ San Alma)

Adana - İncirlik Askeri Üs ( Erse Makine, Kırnak İnşaat, VBR )

THY Kargo, İnşaat ve Teknik A.Ş

Tav – İSTANBUL

Tav Alanya Gazipaşa Havalimanı

Antalya Havalimanı (DHMİ San Alma, Kayaoğlu İnşaat, Kotaz Elektrik, Dizayn Pist)

Batman Havalimanı (DHMİ San Alma, Askeri ortak pist)

Balıkesir – Edremit Havalimanı ( EMT-Doğan Mühendislik)

Aydın Havalimanı ( EMT-Doğan Mühendislik)

Samsun Havalimanı (Gena İnşaat, EMT-Doğan Mühendislik, DHMİ San Alma) Bingöl Havalimanı ( Yek Group)

Urfa Havalimanı(DHMİ Sa n Alma, Günay Günbeton İnşaat)

İzmir Adnan Menderes Havalimanı ( DHMİ)

Hakkari Havalimanı ( Saridağlar İnşaat)

Iğdır Havalimanı (DHMİ Sa n Alma)

Nevşehir Kapadokya Havalimanı ( Gena İnşaat, DHMİ Sa n Alma)

Kahramanmaraş Havalimanı (Türkseven İnşaat)

Tunus Havalimanı ( Tav, Dizayn Pist)

Türkmenistan Havalimanı ( Polimeks İnşaat)

Cezayir Havalimanı ( Tav )

Gürcistan Havalimanı ( Tav )

Makedonya Havalimanı ( Tav )

Tav Cidde Riyad ( UBS Uğur bilgi sistemleri)

Bilumum açık ve kapalı beton sahalar, fabrika içleri…….

TEKNO YAPI KİMYASALLARI SAN. VE TİC. A.Ş.

Istanbul Deri Organize San. Bolgesi Gergef Sok. No : 6 34956 Tuzla / Istanbul/ TURKIYE

Tel: 0216 429 10 00 Fax: 0216 429 02 00 www.teknoyapi.com.tr

e-mail: [email protected]