Cyclone LC Programmers User Manual Purchase Agreement
Total Page:16
File Type:pdf, Size:1020Kb
Cyclone LC Programmers User Manual Purchase Agreement P&E Microcomputer Systems, Inc. reserves the right to make changes without further notice to any products herein to improve reliability, function, or design. P&E Microcomputer Systems, Inc. does not assume any liability arising out of the application or use of any product or circuit described herein. This software and accompanying documentation are protected by United States Copyright law and also by International Treaty provisions. Any use of this software in violation of copyright law or the terms of this agreement will be prosecuted. All the software described in this document is copyrighted by P&E Microcomputer Systems, Inc. Copyright notices have been included in the software. P&E Microcomputer Systems authorizes you to make archival copies of the software and documentation for the sole purpose of back-up and protecting your investment from loss. Under no circumstances may you copy this software or documentation for the purpose of distribution to others. Under no conditions may you remove the copyright notices from this software or documentation. This software may be used by one person on as many computers as that person uses, provided that the software is never used on two computers at the same time. P&E expects that group programming projects making use of this software will purchase a copy of the software and documentation for each user in the group. Contact P&E for volume discounts and site licensing agreements. P&E Microcomputer Systems does not assume any liability for the use of this software beyond the original purchase price of the software. In no event will P&E Microcomputer Systems be liable for additional damages, including any lost profits, lost savings or other incidental or consequential damages arising out of the use or inability to use these programs, even if P&E Microcomputer Systems has been advised of the possibility of such damage. By using this software, you accept the terms of this agreement. ©2015-2019 P&E Microcomputer Systems, Inc. ARM and Cortex are registered trademarksof ARM Ltd. or its subsidiaries. NXP, ColdFire, and Kinetis are registered trademarks of NXP Semiconductors. Texas Instruments and TI are registered trademarks of Texas Instruments Incorporated. STMicroelectronics is a registered trademark of STMicroelectronics, Inc. All other product or service names are the property of their respective owners. P&E Microcomputer Systems, Inc. 98 Galen St. Watertown, MA 02472 617-923-0053 http://www.pemicro.com Manual version: 1.17 July 2019 1 INTRODUCTION.........................................................................................................................................9 1.1 Cyclone Feature Comparison..........................................................................................................................9 1.2 Advanced Feature Licenses............................................................................................................................9 1.2.1 ProCryption Security License ........................................................................................................................................9 1.2.2 Cyclone Control Suite Advanced Features License ....................................................................................................10 1.2.3 SDHC Port Activation License.....................................................................................................................................10 2 QUICK START GUIDE FOR SAP OPERATION.......................................................................................11 2.1 Installing The Cyclone Software....................................................................................................................11 2.2 Setting Up The Cyclone Hardware................................................................................................................11 2.3 Creating A Stand-Alone Programming Image ...............................................................................................13 2.3.1 Advanced Features .....................................................................................................................................................16 2.4 Launching Cyclone Programming .................................................................................................................16 3 CYCLONE LC HARDWARE .....................................................................................................................18 3.1 Touchscreen LCD .........................................................................................................................................18 3.2 LED Indicators...............................................................................................................................................18 3.3 Start Button ...................................................................................................................................................18 3.4 Access Panel.................................................................................................................................................18 3.5 Cyclone System Power .................................................................................................................................19 3.6 RS232 Communication (Serial Port) .............................................................................................................19 3.7 Ethernet Communication...............................................................................................................................19 3.8 USB Communications ...................................................................................................................................19 3.9 Electromechanical Relays.............................................................................................................................19 3.10 Power Connectors.........................................................................................................................................20 3.11 Reset Button..................................................................................................................................................20 3.12 SDHC Port.....................................................................................................................................................20 3.13 Optional Oscillator (MON08 Only).................................................................................................................21 3.14 Cyclone Time / Real Time Clock ...................................................................................................................21 3.15 Power Jumper Settings .................................................................................................................................21 3.16 Debug Connectors ........................................................................................................................................21 3.17 Target Headers For Part# CYCLONE-LC-ARM ............................................................................................23 3.17.1 PORT A: 10-Pin Keyed Mini Connector (Kinetis, S32 (ARM), other PEmicro-Supported ARM devices) ...................23 3.17.2 PORT B: 20-Pin Keyed Mini Connector (Kinetis, S32 (ARM), other PEmicro-Supported ARM devices) ...................24 3.17.3 PORT C: 20-Pin Debug Connector (Kinetis, S32 (ARM), other PEmicro-Supported ARM devices) ..........................25 3.18 Target Headers For Part# CYCLONE-LC-UNIV ...........................................................................................26 3.18.1 PORT A: 10-Pin Keyed Mini Connector (Kinetis, S32 (ARM), other PEmicro-Supported ARM devices) ...................26 3.18.2 PORT B: 20-Pin Keyed Mini Connector (Kinetis, S32 (ARM), other PEmicro-Supported ARM devices) ...................27 3.18.3 PORT C: 14-Pin Debug Connector (MPC55xx-57xx, SPC5, DSC, S32 (Power)) ......................................................28 3.18.4 PORT D: 26-Pin Debug Connector (ColdFire V2/3/4).................................................................................................29 3.18.5 PORT E: 16-Pin Debug Connector (MON08)..............................................................................................................30 3.18.6 PORT F: 6-Pin Debug Connector (RS08, HCS08, HC(S)12(X), S12Z, ColdFire +/V1, STM8 w/ adapter).................31 3.18.7 PORT G: 10-Pin Debug Connector (Power MPC5xx/8xx) ..........................................................................................32 3.18.8 PORT H: 20-Pin Debug Connector (Kinetis, S32 (ARM), other PEmicro-Supported ARM devices) ..........................32 3.19 Ribbon Cable.................................................................................................................................................33 4 TARGET POWER MANAGEMENT ..........................................................................................................34 4.1 Cyclone Configuration...................................................................................................................................34 4.2 Cyclone Setup...............................................................................................................................................36 4.2.1 Independently Powered Target ...................................................................................................................................36