DOCSLIB.ORG

Row Unit Mid-Mount Fertilizer Injection Opener

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Row Unit Mid-Mount Fertilizer Injection Opener ROW UNIT MID-MOUNT FERTILIZER INJECTION OPENER MODELS 2968-050 & 2968-052 – SINGLE WHEEL MODELS 2968-051 & 2968-053 – DUAL WHEEL CNH ROW UNITS SET UP & PARTS MANUAL 2565-960-REV_A – 01/2020 YETTER MANUFACTURING CO. FOUNDED 1930 Colchester, IL 62326-0358 Toll free: 800/447-5777 309/776-3222 (Fax) Website: www.yetterco.com E-mail: [email protected] TABLE OF CONTENTS FOREWORD ………………………………………………….......…............... 3 SAFETY …………………………………………………………...….................. 4 PICTORIAL PART LIST …………………...……………..................... 5 – 9 INSTALLATION …………………………………………………........... 10 – 16 OPERATION .....………..……..…...…………........................... 17 – 18 MAINTENANCE ………......…..…………......………................. 19 – 21 PARTS IDENTIFICATION…...………………....……...…............ 22 – 32 TROUBLESHOOTING…...………………....……...…........................ 33 BOLT TORQUE Important: Over-tightening hardware can cause just as much damage as under-tightening. Tightening hardware beyond the recommended range can reduce its shock load capacity. All hardware is either Grade 5 unless otherwise noted. Grade 5 cap screws are marked with three radial lines on the head. Grade 8 cap screws are marked with six radial lines on the head. If hardware must be replaced, be sure to replace it with hardware of equal size, strength and thread type. Refer to the torque values chart when tightening hardware. The chart below is a guide for proper torque. Use it unless a specified torque is called out elsewhere in the manual. Torque is the force applied to the end of the handle or cheater bar, times the length of the handle or bar. Tightening hardware beyond the recommended range can reduce its shock load capacity. Use a torque wrench wherever possible The following table shows torque in ft.-lbs. for coarse thread hardware. 2 FOREWORD You’ve just joined an exclusive but rapidly Important will apply to the same information as growing club. specified by note only of an immediate and urgent nature. For our part, we want to welcome you to the group and thank you for buying a Yetter product. It is the responsibility of the user to read the operator’s manual and comply with the safe and We hope your new Yetter products will help you correct operating procedure and to lubricate and achieve both goals-increase your productivity and maintain the product according to the increase your efficiency so that you may generate maintenance schedule in the operator’s manual. more profit. The user is responsible for inspecting his This operator’s manual has been designed into machine and for having parts repaired or four major sections: Foreword, Safety replaced when continued use of the product Precautions, Installation Instructions and Parts would cause damage or excessive wear to the Breakdown. other parts. It is the user’s responsibility to deliver his This SAFETY ALERT SYMBOL indicates machine to the Yetter dealer who sold him the important safety messages in the manual. product for service or replacement of defective When you see this symbol, be alert to the parts, which are covered by the warranty policy. possibility of PERSONAL INJURY and carefully read the message that follows. If you are unable to understand or follow the instructions provided in this publication, consult The word NOTE is used to convey information your local Yetter dealer or contact: that is out of context with the manual text. It contains special information such as YETTER MANUFACTURING CO. specifications, techniques and reference 309/776-4111 information of a supplementary nature. 800/447-5777 309/776-3222 (FAX) The word IMPORTANT is used in the text when Website: www.yetterco.com immediate damage will occur to the machine due E-mail: [email protected] to improper technique or operation. WARRANTY Yetter Manufacturing warrants all products manufactured and sold by it against defects in material. This warranty being expressly limited to replacement at the factory of such parts or products as shall appear to be defective after inspection. This warranty does not obligate the Company to bear cost of labor in replacement of parts. It is the policy of the Company to make improvements without incurring obligations to add them to any unit already sold. No warranty is made or authorized to be made, other than herein set forth. This warranty is in effect for one year after purchase. DEALER: ________________________________________ Yetter Manufacturing warrants its own products only and cannot be responsible for damages to equipment on which mounted. 3 BE ALERT! YOUR SAFETY IS INVOLVED WATCH FOR THIS SYMBOL. IT POINTS OUT IMPORTANT SAFETY PRECAUTIONS. IT MEANS “ATTENTION – BE ALERT!” It is your responsibility as an owner, operator, or supervision to know and instruct everyone using this machine at the time of initial assignment and at least annually thereafter, of the proper operation, precautions, and work hazards which exist in the operation of the machine in accordance with OSHA regulations. Safety Is No Accident The following safety instructions, combined with common sense, will save your equipment from needless damage and the operator from unnecessary exposure to personal hazard. Pay special attention to the caution notes in the text. Review this manual at least once a year with all operators. 1. Read and understand the operator’s manual before operating this machine. Failure to do so is considered a misuse of the equipment. 2. Make sure equipment is secure before operating. 3. Always keep children away from equipment when operating. 4. Make sure everyone that is not directly involved with the operation is out of the work area before beginning operation. 5. Make sure all safety devices, shields, and guards are in place and functional before beginning operation 6. Shut off all power to adjust, service, or clean. 7. Keep hands, feet, and clothing away from moving parts. It is a good idea to remove all jewelry before operating. 8. Inspect the machine periodically during operation for signs of excessive wear, loose fasteners, and unusual noises. 4 2968-050 Pictorial Parts List For CNH 2000 Row Units, Single Disc, Left or Right Hand 2968-150 2968-227 ONLY IF –LH ORDERED ONLY IF –RH ORDERED QTY 1 QTY 1 2968-472-LH – QTY 1 2968-472-RH – QTY 1 Bolt Bag Close Wheel Mount Tall Fert. Wheel Mount, LH Tall Fert. Wheel Mount, RH 2968-051-L & 2968-051-R Pictorial Parts List For CNH 2000 Row Units, Dual Disc ONLY IF –L ORDERED ONLY IF –L ORDERED ONLY IF –R ORDERED ONLY IF –R ORDERED 2968-149 2968-227 2968-472-LH – QTY 1 2968-473-RH – QTY 1 2968-472-RH – QTY 1 2968-473-LH – QTY 1 QTY 1 QTY 1 Tall Fert. Short Fert. Tall Fert. Short Fert. Bolt Bag Close Wheel Mount Wheel Mount, LH Wheel Mount, RH Wheel Mount, RH Wheel Mount, LH 2968-052 Pictorial Parts List For CNH 1200 Row Units, Single Disc, Left or Right Hand 2968-113 ONLY IF –L ORDERED ONLY IF –R ORDERED QTY 1 2968-230 – QTY 1 2968-403-LH – QTY 1 2968-403-RH – QTY 1 Bolt Bag Close Wheel Mount TALL CNH 1200 LHL ARM TALL CNH 1200 RHL ARM 2968-053-L Pictorial Parts List For CNH 1200 Row Units, Dual Disc, LH Lead 2968-114 2968-403-LH – QTY 1 2968-404-RH – QTY 1 QTY 1 2968-230 – QTY 1 TALL CNH 1200 LHL ARM RH CNH 1200 SHORT ARM Bolt Bag Close Wheel Mount 5 2968-053-R Pictorial Parts List For CNH 1200 Row Units, Dual Disc, RH Lead 2968 -114 – QTY 1 2968-230 – QTY 1 2968-403-RH – QTY 1 2968-404-LH – QTY 1 Bolt Bag Close Wheel Mount TALL CNH 1200 RHL ARM LH CNH 1200 SHORT ARM 2968-054 Pictorial Parts List Box Mount Kit For CNH 2100 Row Units 2502-807 – QTY 8 2520-477 – QTY 4 2968-374 – QTY 2 2968-375 – QTY 4 M16X2X80 Bolt M16X2 Hex Nut Box Mount Bracket Box Mount Spacer 2968-132 Pictorial Parts List 10” Fertilizer Wheel Assembly 2505-207 – QTY 4 2520-206 – QTY 4 2570-740 – QTY 1 2965-128 – QTY 1 2965-352 – QTY 1 2968-320 – QTY 1 5/16 X 1 ¼ 5/16 Flange Flanged D-Bolt Hub & Bearing Hub Cap Casting 10” Notched Blade Carriage Bolt Lock Nut 5/8 X 2.812 GR 8 Assembly, 4 bolt 6 2968-090A-L & 2968-090A-R Pictorial Parts List ● = ONLY INCLUDED IN 2968-090A-L KIT + = ONLY INCLUDED IN 2960-090A-R KIT 2502-251 - 3/8-16 X 3 HHCS GR 8 ZP – QTY 2 2502-252 - 3/8-16 X 1 1/2 HHCS GR 2 ZP – QTY 1 2520-251 - 3/8-16 HEX NUT GR 2 ZP – QTY 3 2525-251 - 3/8 LOCK WASHER ZP – QTY 3 2526-253 - 3/8 FLAT WASHER ZP – QTY 4 2570 - 727 - 3/8 HOSE P-CLIP W/ VINYL CUSHION – QTY 1 ● 2968 - 229 - L – KNIFE/TUBE W.A. – LH – QTY 1 +2968-229-R – KNIFE/TUBE W.A. – RH – QTY 1 ●2968-396-L – TORSION SPRING – LH WOUND – QTY 1 +2968-396-R – TORSION SPRING – RH WOUND – QTY 1 2968-401 – STEPPED BUSHING – QTY 1 2968-402 – STOP BUSHING – QTY 1 2968-091 INJECTOR KIT, ONE SIDE 2515-846 -MALE CONNECTOR - 3/8 X 1/4 NPTF– QTY 1 2520-253 -3/8-16 JAM HEX NUT, GR 2, ZP– QTY 2 2525-251 - 3/8 LOCK WASHER ZP – QTY 1 2526-253 - 3/8 FLAT WASHER ZP – QTY 2 2968-218 - INJECTOR HOLDER W.A. – QTY 2 7 2968-113 Pictorial Parts List Bolt Bag for 2968-052 – 2505-207 5/16 – 18 X 1 ¼ CARRIAGE BOLT – QTY 4 2505-208 – 5/16 – 18 X 1 ½ CARRIAGE BOLT – QTY 4 2505-345 – ½ – 13 X 2 CARRIAGE BOLT – QTY 3 2520-206 – 5/16 FLANGE LOCK NUT – QTY 8 2520-357 1/2-13 LOCK HEX NUT, GR A, ZP– QTY 3 2520-464 -5/8-11 WHIZLOCK ZP, GR 8– QTY 1 2526-355 – ½ FLAT WASHER HRD'ND ZP – QTY 3 2526-454 - 5/8 SAE FLATWASHER HRD'ND ZP – QTY 1 2570-448 - .120 BOWTIE LOCKING COTTER ZP – QTY 1 2968-383 – TRIANGULAR MOUNT SPACER ZP – QTY 4 2968-386 – TRIANGULAR MOUNT – QTY 2 2984-497 – AIR CYLINDER ROD PIN – QTY 1 2968-114 Pictorial Parts List Bolt Bag for 2968-053 2505-207 – 5/16 – 18 X 1 ¾ CARRIAGE BOLT – QTY 4 2505-208 – 5/16 – 18 X 1 ½ CARRIAGE BOLT – QTY 4 2505-343 – ½ – 13 X 2 ½ CARRIAGE
Load more

Recommended publications
  • RV1 Tire Changer Manual
    1645 Lemonwood Dr. Santa Paula, CA 93060 USA Toll Free: (800) 253-2363 Telephone: (805) 933-9970 rangerproducts.com Wheel Guardian™ Tire Changer Installation and Operation Manual Manual P/N 5900089 — Manual Revision A3 — November 2019 Model: • RV1 Designed and engineered in Southern California, USA. Made in China. Read the entire contents of this manual before using this product. Failure to follow the instructions and safety precautions in ⚠ DANGER this manual can result in serious injury or death. Make sure all other operators also read this manual. Keep the manual near the product for future reference. By proceeding with setup and operation, you agree that you fully understand the contents of this manual. Manual. RV1 Wheel Guardian™ Tire Changer, Installation and Operation Manual, Manual P/N 5900089, Manual Revision A3, Released November 2019. Copyright. Copyright © 2019 by BendPak Inc. All rights reserved. You may make copies of this document if you agree that: you will give full attribution to BendPak Inc., you will not make changes to the content, you do not gain any rights to this content, and you will not use the copies for commercial purposes. Trademarks. BendPak, the BendPak logo, Ranger, and the Ranger logo are registered trademarks of BendPak Inc. All other company, product, and service names are used for identification only. All trademarks and registered trademarks mentioned in this manual are the property of their respective owners. Limitations. Every effort has been made to have complete and accurate instructions in this manual. However, product updates, revisions, and/or changes may have occurred since this manual was published.
    [Show full text]
  • Unavoidable Friction Within Servo Motors
    UC San Diego UC San Diego Electronic Theses and Dissertations Title Design of running-man, a bipedal robot Permalink https://escholarship.org/uc/item/11r612s9 Author Chen, Jin Publication Date 2011 Peer reviewed|Thesis/dissertation eScholarship.org Powered by the California Digital Library University of California University of California, San Diego Design of running-man, a bipedal robot A Thesis submitted in partial satisfaction of the requirements for the degree Master of Science in Engineering Sciences (Mechanical Engineering) by Jin Chen Committee in charge: Professor Tom Bewley, Chair Professor Prab Bandaru Professor Mauricio de Oliveira 2011 Copyright Jin Chen, 2011 All rights reserved. The Thesis of Jin Chen is approved and it is acceptable in quality and form for publication on microfilm and electronically: Chair University of California, San Diego 2011 iii To my parents and my brother, whose supports of my education are ever so generous iv TABLE OF CONTENTS Signature Page ........................................................................................................iii Dedication ............................................................................................................... iv Table of Contents..................................................................................................... v List of Figures.........................................................................................................vii List of Tables............................................................................................................ix
    [Show full text]
  • Numerical and Experimental Analysis of Torsion Springs Using NURBS Curves
    applied sciences Article Numerical and Experimental Analysis of Torsion Springs Using NURBS Curves Young Shin Kim 1, Yu Jun Song 2 and Euy Sik Jeon 3,* 1 Industrial Technology Research Institute, Kongju National University, Cheonan-daero, Seobuk-gu, Cheonan-si 31080, Chungcheongnam-do, Korea; [email protected] 2 International Testing and Evaluation Laboratory (ITEL), 53, Osongsaengmyeong 10-ro, Osong-eup, heungdeok-gu, Cheongju-si 28164, Chungcheongbuk-do, Korea; [email protected] 3 Department of Mechanical Engineering, Graduate School, Kongju National University, Cheonan-daero, Seobuk-gu, Cheonan-si 31080, Chungcheongnam-do, Korea * Correspondence: [email protected]; Tel.: +82-41-521-9284 Received: 28 March 2020; Accepted: 7 April 2020; Published: 10 April 2020 Abstract: Torsion springs, which transfer power through the twisting of their coil, provide advantages such as module simplification and efficient use of space. The design of a torsion spring has been formulated, but it is difficult to determine the local behaviors of torsion springs according to actual load conditions. This study proposes a torsion-spring design method through finite element analysis (FEA) using nonuniform-rational-basis-spline (NURBS) curves. Through experimentation, the angle and displacement values for the actual spring load were converted into useable data. Torsion-spring displacement values were obtained via experimentation and converted into coordinates that may be expressed using NURBS curves. The results of these experiments were then compared to those obtained via FEA, and the validity of this method was thereby verified. Keywords: torsion springs; FEA; NURBS; applied load; local behaviors 1. Introduction Torsion springs transfer power through the twisting of their coil, and provide advantages such as module simplification, efficient use of space, and reduction of overall product weight.
    [Show full text]
  • Transverse Leaf Springs: a Corvette Controversy
    Transverse Leaf Springs: A Corvette Controversy By Matt Miller Introduction A lot of people give Corvettes flack because they employ leaf springs. The mere mention of leaf springs conjures up images of suspensions on horse-drawn buggies, old cars and trucks, and Harbor Freight utility trailers. Even magazine reviews of the latest Corvettes talk about how “antiquated” their leaf spring designs are, and many a Corvette enthusiast has converted his car to aftermarket coilovers in the belief that they are inherently better than the composite transverse leaf springs found on the front and rear suspensions of all Corvettes since 1984. But is that true? Does the Corvette’s use of transverse leaf springs mean it has an inferior, outdated suspension design? The short answer is “No!” To find out why, we’ll cover some basics on springs and suspensions and see how the facts add up. Page 1 What is a Spring, Anyway? We all intuitively know what springs are. But technically speaking, a spring is an elastic mechanical device that stores potential energy. When mechanical energy is put into a spring, it deforms and can release that energy back in the opposite direction. We measure a spring’s energy storage by its “spring rate,” which defines its energy storage. The spring rate defines the increase in force required to move the spring a certain amount. For example, if a spring has a rate of 100 lb/in (pounds per inch), it means that 100 lbs of force will move one end of it 1”, an additional 100 lbs will move it another inch, and so on.
    [Show full text]
  • Analysis of Hollow Torsion Bar Made of E- Glass Fiber Reinforced Composite Material
    Volume III, Issue V, May 2016 IJRSI ISSN 2321 – 2705 Analysis of Hollow Torsion Bar Made of E- Glass Fiber Reinforced Composite Material 1 2 M.Prakash , R.Sureshkumar 1 PG student, Gnanamani College of Technology, Namakkal 2 Assistant Professor, Gnanamani College of Technology, Namakkal Abstract: The purpose of this study is to investigate stress values of composite torsion bar suspension system. In this analytical study, round solid composite bar is taken. The analytical was carried out on a ANSYS, which was built specifically to investigate the static characteristics of torsion bar used in vehicle suspension system. This paper provides fundamental knowledge of structural test and significant parameters such as stress, total deformation, equivalent stress are highlighted. Thus the deflections were obtained analytically. The results of this study could provide a better light weight torsion suspension system. Keywords: Torsion bar, Ansys, Total deformation , Stress I. INTRODUCTION Fig 1 position of torsion bar torsion bar suspension, also known as a torsion spring manufacturing process. Torsion bars are used as automobile A suspension or torsion beam suspension, is a general term suspension. They offer easy adjustment on ride height for any vehicle suspension that uses a torsion bar as its main depending on the weight of the car. Torsion bars are weight bearing spring. One end of a long metal bar is attached essentially metal bars that function as a spring. At one end, firmly to the vehicle chassis; the opposite end terminates in a the torsion bar is fixed firmly in place to the chassis or frame lever, the torsion key, mounted perpendicular to the bar, that is of the vehicle.
    [Show full text]
  • Conceptual Design and Analysis of Four Types of Variable Stiffness Actuators Based on Spring Pretension
    International Journal of Advanced Robotic Systems ARTICLE Conceptual Design and Analysis of Four Types of Variable Stiffness Actuators Based on Spring Pretension Regular Paper Jishu Guo1 and Guohui Tian1* 1 School of Control Science and Engineering, Shandong University, Jinan, Shandong, China *Corresponding author(s) E-mail: [email protected] Received 12 November 2014; Accepted 17 March 2015 DOI: 10.5772/60580 © 2015 The Author(s). Licensee InTech. This is an open access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/3.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited. Abstract between the output stiffness and the angular deflection is fairly linear. The conceptual layouts and working princi‐ The variable stiffness actuator (VSA) is an open research ples are elaborated for the four actuators. The characteris‐ field. This paper introduces the conceptual design and tics of torque and stiffness of the VSAs are presented, and analysis of four types of novel variable stiffness actuators the mechanical solutions are illustrated. (VSAs). The main novelty of this paper is focused on the convenience control of the torque and stiffness of the Keywords Variable stiffness actuator, Approximate actuator. We do not need to design complicated control quadratic spring, Characteristics of torque and stiffness, strategies to achieve the desired actuating torque and Convenient to control, Mechanical solution output stiffness. This feature is beneficial for real-time control. In order to achieve this advantage, three types of approximate quadratic springs and four types of stiffness regulation mechanisms are presented.
    [Show full text]
  • Download Full Article As
    Article Effect of mass and center of gravity on vehicle speed and braking performance Jack Tian1 and Clifford Whitfield2 1 Troy High School, Fullerton, CA 2 Department of Mechanical and Aerospace Engineering, The Ohio State University, Columbus, OH SUMMARY to demonstrate the effect of changing CG position on vehicle The center of gravity (CG) of a vehicle is a key stability (1). Albeit with different purpose, this study formed parameter that helps determine vehicle stability, the basis of our hypothesis. Other vehicle parameters were braking efficiency, and safety. In a gravity vehicle, also informed by previous studies. For example, a study on the mass of the vehicle is also an important factor vehicle load found that an increase in CG height results in a in vehicle performance because it provides the sole decrease in maximum driving speed since stability decreases force of propulsion. We hypothesized that if a vehicle as CG height increases (2). Therefore, in order to minimize the adverse impact of the height of CG on vehicle stability, was constructed according to mathematically- the vehicle was designed to move as closely as possible derived optimal mass and CG location, then a fast to the ground. Skrucany et al. investigated the influence of and accurate vehicle would result. To test this cargo weight and its position on brakes. They demonstrated hypothesis, we constructed a gravity vehicle, which that loads should be as close to the ground and rear axle is a vehicle powered by its own gravity on a ramp. as possible to reduce the braking distance (3, 4).
    [Show full text]
  • Tire Changer REPAIR PARTS
    Tire Changer REPAIR PARTS Tire Changers TABLE OF CONTENTS Mount / Demount Heads .......................................................2–4 Filters / Regulators / Lubricators .............................................5 Seal Kits And Parts................................................................6–7 Motors, Vanes And Misc. Parts ................................................8 Commonly Requested Tire Changer Parts, Tools and Accessories ...................................................9–14 Tire Changer Air Blast Dump Valves .....................................14 Plastic Protection Inserts, Jaw Covers, Bead Breaker Blade Covers, and more ......................15–33 Commonly Requested Parts for: Accu-Turn / Bosch ..........................................................34–37 All Tool ..................................................................................38 Atlas ......................................................................................39 Butler ..............................................................................40–52 Cemb ..............................................................................43–46 Repair Parts for: Coats®* ..........................................................................47–67 Tire Changer Foot Pedal Control Valves ....................52–53 Corghi .............................................................................68–80 Cormach .........................................................................81–83 FMC / John Bean (JBC) .................................................84–88
    [Show full text]
  • ATDTCHD & ATDTCHDPA Tire Changer Installation and Operation
    ATDTCHD & ATDTCHDPA Tire Changer Installation and Operation Manual Features: x Swing Arm Design x Handles Tires up to 47" and Rim widths up to 15" x Press Arm for Low Profile Tires x Four Pneumatic Clamps and double-acting Cylinders x Side mounted Bead Breaker x Bead seating Inflation Jets in Clamping Jaws x No Scratching - machine never contacts the Rim x Lubricator, Water Separator and Air Pressure Regulator x 26" x 26" square Turntable that accommodates Wheel Diameters up to 47" ATDTCHD_ATDTCHDPA_rev0717 WARNING This instruction manual is an important part of the product. Please read it thoroughly before installing, operating or performing maintenance on this machine. This machine is only designed to mount, demount and inflate the tire in the specified scope and not for any other purpose. The manufacturer will not be responsible for damage or injury caused by the improper operation of this equipment. NOTE: This machine should only be operated by special trained qualified personnel. When operating, any unauthorized persons should be kept far away from the machine. Please note the safety related decals attached to this machine. They should be replaced if illegible or missing. Users and bystanders should use safety goggles or safety glasses with side shields that comply with current national standards. Also use non-skid safety shoes, hard hat, gloves and hearing protection when appropriate. To reduce the risk of personal injury, keep hair, loose clothing, fingers, and all body parts away from moving parts of the machine. Tire changer should be installed and fixed on the flat and solid floor. Two feet of distance from the rear and lateral side of the machine to the wall can guarantee the perfect air flow and enough operation space.
    [Show full text]
  • Eindhoven University of Technology MASTER Design of Active Suspension Using Electromagnetic Devices Janssen, J.L.G
    Eindhoven University of Technology MASTER Design of active suspension using electromagnetic devices Janssen, J.L.G. Award date: 2006 Link to publication Disclaimer This document contains a student thesis (bachelor's or master's), as authored by a student at Eindhoven University of Technology. Student theses are made available in the TU/e repository upon obtaining the required degree. The grade received is not published on the document as presented in the repository. The required complexity or quality of research of student theses may vary by program, and the required minimum study period may vary in duration. General rights Copyright and moral rights for the publications made accessible in the public portal are retained by the authors and/or other copyright owners and it is a condition of accessing publications that users recognise and abide by the legal requirements associated with these rights. • Users may download and print one copy of any publication from the public portal for the purpose of private study or research. • You may not further distribute the material or use it for any profit-making activity or commercial gain 12 Capaciteitsgroep Elektrische Energietechniek Electromechanics & Power Electronics Master of Science Thesis Design of Active Suspension using Electromagnetic Devices J.L.G. Janssen EPE.2006.A.08 The department Electrical Engineering of the Technische Universiteit Eindhoven does not accept any responsibility for the contents of this report Coaches: dr. J.J.H. Paulides, TU/e dr. E.A. Lomonova, TU/e prof.dr.ir. A.J.A. Vandenput, TU/e ir. J. Zuurbier, TNO Automotive ir. N.J.
    [Show full text]
  • The Essential Guide to Spring Technology
    THE ESSENTIAL GUIDE TO SPRING TECHNOLOGY www.springs.co.uk CONTENTS Introduction 3 Springtech 4 Extension Springs 6 Exension Spring Design Definitions 7 Extension Spring End Configurations 8 Torsion Springs 9 Torsion Spring Design Definitions 10 Compression Springs 12 Compression Spring Design Definitions 13 Compression Springs - Other Configurations 14 Pressed Strip Springs 15 Wave Spring Washers 16 Wire Forms 16 Standard Wire Gauges 18 Conversion Tables 20 Manufacture 22 Terminology 24 Notes 29 INTRODUCTION The Essential Guide to Spring Technology provides important technical information concerning the specification, behavioural and design characteristics that should be considered when formulating spring technology products. The incorporation of spring design in the early stages of any new product development project is essential if later compromises, which can negatively impact application performance and reliability, are to be avoided. Helical spring engineering has become increasingly specialised as advances in design software have enabled ever more sophisticated products to be conceived. At Springtech our Design Engineers provide the specialist expertise to support your new product development project. If you have any technical questions, or are looking for a design partner for your spring project, please contact us at: Tel: +44 (0) 1494 556 700 Email: [email protected] 3 www.springs.co.uk Springtech - Spring Technology Experts We specialise in designing, developing and manufacturing high performance, quality-driven springs,
    [Show full text]
  • Extension & Torsion Springs (Chapter
    Extension & Torsion Springs (Chapter 10) Extension Springs Extension springs are similar to compression springs within the body of the spring. To apply tensile loads, hooks are needed at the ends of the springs. Some common hook types: Fig. 10–5 Shigley’s Mechanical Engineering Design Normal Stress in the Hook vs. Shear Stress in Body In a typical hook, a critical stress location is at point A, where there is bending and axial loading. (K)A is a bending stress-correction factor for curvature Fig. 10–6 Shigley’s Mechanical Engineering Design Stress in the Hook Another potentially critical stress location is at point B, where there is primarily torsion. (K)B is a stress-correction factor for curvature. Fig. 10–6 Shigley’s Mechanical Engineering Design Close-wound Extension Springs Extension springs are often made with coils in contact with one another, called close-wound. Including some initial tension in close-wound springs helps hold the free length more accurately. The load-deflection curve is offset by this initial tension Fi Fig. 10–7 Shigley’s Mechanical Engineering Design Terminology of Extension Spring Dimensions The free length is measured inside the end hooks. The hooks contribute to the spring rate. This can be handled by obtaining an equivalent number of active coils. Fig. 10–7 Shigley’s Mechanical Engineering Design Helical Spring: Coiled Extension Spring Similar to compressions springs, but opposite direction Equilibrium forces at cut section anywhere in the body of the spring indicates direct shear and torsion Fig. 10–1 Shigley’s Mechanical Engineering Design Stresses in Helical Springs Torsional shear and direct shear Additive (maximum) on inside fiber of cross-section Substitute terms Fig.
    [Show full text]