Humidity Measurement in Blast Furnace Gas

Total Page：16

File Type：pdf, Size：1020Kb

YOUR PARTNER IN SENSOR TECHNOLOGY R Ges.m.b.H. HUMIDITY MEASUREMENT IN BLAST FURNACE GAS With the EE31-MFT with pressure- proof probe, stainless steel sinter ﬁ lter and sensor coating, E+E Elektronik provides the optimum solution for this application. Measurement setup Using ball valve measuring systems Measurement of the absolute humidity in blast furnace gas is the pressure and temperature of the necessary to determine its heating value for further use. medium changes frequently, which Blast furnace gas is a by-product of blast furnaces and is pro- has a direct effect on the absolute duced by the reduction of iron ore to metallic iron. humidity. Blast furnace gas consists of about 45-60% nitrogen; 20-30% carbon monoxide, 20-25% carbon dioxide, 2-4% hydrogen and a little methane. Because of its high nitrogen content, blast furnace gas has a very low heating value (approx. 93 BTU/ft3), but in spite of this it is used as a fuel in steel plants. To determine the heating value, the blast furnaces are equipped with ball valve measuring stations to analyze the gas. In addition to the measurement of CO, CO2, H2 and CH4, determining the absolute humidity is deci- sively important for determining the heating value. • Application conditions Measurement range: 0 - 300 g/m³, typical measurement value: 10 g/m³ Output: 4..0000.20 mA Operating temperature: ~ 20 °C Operating pressure: ~ 70 bar vacuum • E+E Product EE31-MFT Humidity measuring transducers for high-humidity and chemical applications High accuracy measurement of relative humidity, dewpoint and temperature even with high humidity close to the condensation point or with high levels of chemical contamination. E+E Elektronik Ges.m.b.H. • Langwiesen 7 • A-4209 Engerwitzdorf • Austria Tel: +43 (0)7235 605-0 • Fax: +43 (0)7235 605-8 • [email protected] • www.epluse.com LG Linz Fn 165761 t • VAT-ID-No. ATU44043101 • place of jurisdiction: A-4020 Linz • DVR0962759.

Copy Link

Recommended publications

Investigation of Waste Biogas Flame Stability Under Oxygen Or Hydrogen-Enriched Conditions
energies Article Investigation of Waste Biogas Flame Stability Under Oxygen or Hydrogen-Enriched Conditions Nerijus Striugas,¯ Rolandas Paulauskas *, Raminta Skvorˇcinskiene˙ and Aurimas Lisauskas Laboratory of Combustion Processes, Lithuanian Energy Institute, Breslaujos str. 3, LT-44403 Kaunas, Lithuania; [email protected] (N.S.); [email protected] (R.S.); [email protected] (A.L.) * Correspondence: [email protected]; Tel.: +370-37-401830 Received: 18 August 2020; Accepted: 9 September 2020; Published: 11 September 2020 Abstract: Increasing production rates of the biomethane lead to increased generation of waste biogases. These gases should be utilized on-site to avoid pollutant emissions to the atmosphere. This study presents a flexible swirl burner (~100 kW) with an adiabatic chamber capable of burning unstable composition waste biogases. The main combustion parameters and chemiluminescence emission spectrums were examined by burning waste biogases containing from 5 to 30 vol% of CH4 in CO2 under air, O2-enriched atmosphere, or with the addition of hydrogen. The tested burner ensured stable combustion of waste biogases with CH4 content not less than 20 vol%. The addition of up to 5 vol% of H2 expanded flammability limits, and stable combustion of the mixtures with CH4 content of 15 vol% was achieved. The burner flexibility to work under O2-enriched air conditions showed more promising results, and the flammability limit was expanded up to 5 vol% of CH4 in CO2. However, the combustion under O2-enriched conditions led to increased NOx emissions (up to 1100 ppm). Besides, based on chemiluminescence emission spectrums, a linear correlation between the spectral intensity ratio of OH* and CH* (IOH*/ICH*) and CH4 content in CO2 was presented, which predicts blow-off limits burning waste biogases under different H2 or O2 enrichments.
[Show full text]
Prima PRO Process Mass Spectrometer No
APPLICATION NOTE Prima PRO process mass spectrometer No. ?????? Accurate multi-component blast furnace gas analysis maximizes iron production and minimizes coke consumption Author: Graham Lewis, Thermo Fisher Scientific, Winsford, Cheshire, United Kingdom Key words • Top gas analysis • Below burden probe • Gas efficiency • Coke rate • Mass balance • Calorific value • Heat balance • Magnetic sector • Above burden probe Introduction Over a billion tonnes of iron a year are produced in These reduction zones are shown in Figure 1. blast furnaces, representing around 94% of global iron production1. The blast furnace consists of a large steel stack, lined with refractory brick. Iron ore, coke and limestone are dropped into the top of the furnace and preheated air blown into the bottom through nozzles called ‘Tuyeres’. Iron oxides are reduced in the melting zone, or ‘Bosh’, forming liquid iron (called ‘hot metal’) and liquid slag. These liquid products are drained from the furnace at regular intervals, and the blast furnace will run continuously for several years, until the refractory lining needs replacing. A wide variety of chemical reactions take place in the blast furnace. At the elevated temperatures towards the bottom Figure 1 of the furnace, a series of direct reduction reactions take Reduction place; these can be simplified to: profile in the blast furnace FeO + C = Fe + CO At lower temperatures higher up in the furnace, a series of indirect reduction reactions take place, simplified to: FeO + CO = Fe + CO2 Analysis of carbon monoxide (CO) and carbon dioxide Process control requirements (CO2) give vital information on the efficiency of the reduction The advantages of process MS over conventional analysis processes.
[Show full text]
Potential Impacts on the Energy System at the Integrated Steelwork by Changing Injection Coal Types to the Blast
A publication of CHEMICAL ENGINEERING TRANSACTIONS The Italian Association VOL. 35, 2013 of Chemical Engineering www.aidic.it/cet Guest Editors: Petar Varbanov, Jiří Klemeš, Panos Seferlis, Athanasios I. Papadopoulos, Spyros Voutetakis Copyright © 2013, AIDIC Servizi S.r.l., ISBN 978-88-95608-26-6; ISSN 1974-9791 DOI: 10.3303/CET1335162 Potential Impacts on the Energy System at the Integrated Steelwork by Changing Injection Coal Types to the Blast Furnace Joel Orre*,a, Chuan Wanga, Johannes Larssonb, Erik Olssonb a 97512, Luleå, Sweden Swerea Mefos, Box 812, SE- b SSAB EMEA Oxelösund, SSAB SE-613 80, Oxelösund, Sweden [email protected] Pulverized coal is often injected into the blast furnaces (BFs) at the integrated steelworks as reducing agent for the hot metal production. The BF process will behave different depending on the injection coal used. The objective of this study is to investigate how different types of coal will influence the BF, and the total energy system at an integrated steel plant. The major process units covered in the model are coking plant, BF, reheating furnace at the rolling mill and a power plant. They are all linked to each other via the main products as well as process gases (i.e. blast furnace gas (BFG) and coke oven gas (COG)) and oxygen network. At the studied plant, the mixed gas of BFG and COG is used within the coking batteries at the coking plant and hot stoves at the BF. The fuel used at the reheating furnace is COG and oil with high heating values. In total, 13 different types of coal and one biomass charcoal are included in the study.
[Show full text]
Combustion of Coal Combustion Is a Rapid Chemical Reaction Between Fuel and Oxygen
Combustion of Coal Combustion is a rapid chemical reaction between fuel and oxygen. When combustible elements of fuel combine with O2, heat energy comes out. During combustion combustible elements like Carbon, Sulfur, Hydrogen etc combine with oxygen and produce respective oxides. The source of oxygen in fuel combustion is air. By volume there is 21% of Oxygen presents in air and by weight it is 23.2%. Although there is 79% (by volume) nitrogen in air but it plays no role in combustion. Actually Nitrogen carries heat produced during combustion to steam boiler stack. As per combustion theory the quantity of air required for combustion is that which provides sufficient O2 to completely oxidize combustible elements of fuel. This quantity of air is normally known as STOICHIOMETRIC AIR requirement. Different types of coal combustion techniques Combustion of Coal Combustion may be defined as the rapid high temperature complicated chemical reaction of oxygen with carbon, hydrogen and sulphur of coal. These reactions follow mainly four steps 1. Formation of coal-oxygen complexes with evolution of heat. 2. Decomposition of these complexes with the generation of CO2 and H2O molecules and formation of carboxyl (COOH), carbonyl (C=O) and phenolic -OH groups along with more heat generation. 3. Decomposition of these groups to produce CO, CO2, H2, H2O and hydrocarbons such as ethane, ethylene, propylene etc. 4. Decomposition of aliphatic structure (relating to or denoting organic compounds in which carbon atoms form open chains (as in the alkanes), not aromatic rings.) with the formation of CO, CO2 and H2O. In low temperatures, the first step is developed faster than others.
[Show full text]
Southern Cone Energy Infrastructure
Southern Cone Energy Infrastructure The integrated energy markets of the Southern Cone have shared a common roller coaster ride for gas supply availability and sourcing Governments are likely will continue to insure that internal markets have “first dibs” on local production. Significant investment in midstream infrastructure is required to realize both public and investor goals. The GNEA pipeline has been an important step in expanding Argentina’s gas suppliers access its northern provinces. Bolivia’s supply role has been shifting and could be as a partner in regional LNG export projects. Recently idle pipeline connections between Chile and Argentina may provide potential The Vaca Muerta unconventional “short cut access” to gas boom has shifted Argentina back growth Asian oil and into a gas export role. Winners of the gas customers. April 2019 offshore Round 1 blocks also must consider gas market outlet options in their development programs and projected ROI. Southern Cone - Power Generation Kit Status details Total capacity MegaWatts for status groups and Fuel types Unde r Construction Unde r Consideration Shutdown or Standby Shutdown Removed Questionable Proj Planne d Operating Idle Engineering Cons t Compltd/Testg Cancelled 0 2000040000 6000080000 100000 120000 140000 160000 180000 ¢Biomass ¢Fuel Oil ¢LNG ¢Oil ¢Solar ¢Blast Furnace Gas ¢Geothermal ¢LPG ¢Other ¢Waste ¢Coal ¢Hydr opower ¢Natural Gas ¢Refinery Coke ¢Waste Heat ¢Diesel/Distillate ¢Landfill Ga s ¢Nuclear ¢Refinery Ga s ¢Wind Power generation will Gas accounts for about Loss of Argentina gas continue to be a primary half of Argentina’s supply access forced outlet for regional generation kit. Peak Chile to install two LNG gas production.
[Show full text]
THE ART of the POSSIBLE the Fuel Flexibility of GE Power's
GEA34108 GAS TO POWER: THE ART OF THE POSSIBLE The Fuel Flexibility of GE Power’s Aeroderivative Gas Turbines GE Power GAS TO POWER: THE ART OF THE POSSIBLE The Fuel Flexibility of GE Power’s Aeroderivative Gas Turbines Dr. Jeffrey Goldmeer, Adrien Sanz, Monamee Adhikari, Amanjit Hundal GEA34108 2018 © 2019 General Electric Company. All rights reserved. GAS TO POWER: THE ART OF THE POSSIBLE The Fuel Flexibility of GE Power’s Aeroderivative Gas Turbines GEA34108 CONTENTS Introduction . 3 GE’s Aeroderivative Gas Turbine Fleet . 3 Gas Turbine Fuel Flexibility . 3 Aeroderivative Gas Turbine Combustion Technology . 4 Fuel Definitions, Sources, and Characteristics . 6 Aeroderivative Fuel Flex Capabilities & Field Experience . .11 Fuel Blending . 14 The Economic Value of Fuel Flexibility . 15 Fuel Flexibility & Economics: Gas Turbines vs. Reciprocating Engines . 16 Summary . .18 Nomenclature . 18 References . .18 2 © 2019 General Electric Company. All rights reserved. GEA34108 GAS TO POWER: THE ART OF THE POSSIBLE The Fuel Flexibility of GE Power’s Aeroderivative Gas Turbines INTRODUCTION As the world’s demand for electricity continues, there are numerous opportunities for gas turbines to be part of the generation solution. Due to their installation and operational characteristics, aeroderivative gas turbines play a key role in power generation. Adding to this capability, aeroderivative gas turbines are highly fuel-flexible, able to operate on a wide variety of gaseous and liquid fuels. This paper provides an overview of these fuel flexibility capabilities, including technical details and operational experience. GE’s AERODERIVATIVE GAS TURBINE FLEET Today’s aeroderivative fleet includes more than 5,000 gas turbines, with more than 135 million operating hours.
[Show full text]
Blast-Furnace Processes for the Production of Phosphatic and Potassic Fertilizer Materials
TECHNICAL BULLETIN NO. 543 APRIL 1937 BLAST-FURNACE PROCESSES FOR THE PRODUCTION OF PHOSPHATIC AND POTASSIC FERTILIZER MATERIALS P. H. ROYSTER Formerly Chemical Engineer K. G. CLARK Chemical Engineer T. P. HIGNETT Formerly Junior Chemist L. E. BOWE Formerly Assistant Chemist H. I. LANSDON Formerly Assistant Chemical Engineer J. C. SOUTHARD Associate Chemist J. W. TURRENTINE Formerly Senior Chemist Fertilizer Research Division Bureau of Chemistry and Soils UNITED STATES DEPARTMENT OF AGRICULTURE, WASHINGTON, D. C, Technical Bulletin No. 543 April 1937 UNITED STATES DEPARTMENT OF AGRICULTURE WASHINGTON, D. C BLAST-FURNACE PROCESSES FOR THE PRODUC- TION OF PHOSPHATIC AND POTASSIC FERTILIZER MATERIALS By P. H. RoYSTER, formerly chemical engineer; K. G. CLARK, chemical engineer; T. P. HiGNETT, formerly junior chemist; L. E. BOWE, formerly assistant chemist; H. I. LANSDON, formerly assistant chemical engineer; J. C. SOUTHARD, associate chemist; and J. W. TURRENTINE, formerly senior chemist, Fertilizer Research Division, Bureau of Chemistry and Soils ^ ^ CONTENTS Page Phosphate smelting—Continued. rags Introduction 1 Description of experiments and presenta- Work of other investigators 3 tion of data 21 Phosphate smelting 3 Interpretation of results 27 Potash and combined potash-phosphate Determination of material requirements_. _ 38 smelting 3 Potash smelting 47 General features of a blast furnace 4 Applicability of the blast-furnace process.. 47 Furnace stack 4 Description of experiments and presenta- Mechanism of combustion 5 tion of data 48 Temperature of combustion zone 5 Interpretation of results 52 Thermal efíiciency of the blast furnace 7 Determination of material requirements_ _ _ 56 The experimental blast-furnace plant 8 Potash-phosphate smelting 60 Furnace stack _ 8 Applicability of the blast-furnace process.
[Show full text]
Methanol from Coke-Oven Gas
Methanol from Coke-oven Gas PEP Review 2019-06 November 2019 Syed Naqvi Research and Analysis Director Process Economics Program IHS Markit | PEP Review 2019-06 Methanol from Coke-oven Gas PEP Review 2019-06 Methanol from Coke-oven Gas Syed Naqvi, Research and Analysis Director Abstract This review presents a technoeconomic of a methanol production process based on coke-oven gas (COG) as a starting material. On the PEP evaluation timeline, this review follows a recently published PEP report (43F), which presented the technoeconomic evaluation of four major methanol manufacturing technologies that are based on natural gas used to make synthesis gas—an intermediate product produced in the methanol manufacturing process. COG is a by-product of the coking process used in steel manufacturing. Besides COG, other major byproducts of the steel making process are blast furnace gas (BFG) and oxygen furnace gas (OFG). COG has the highest calorific value and a high hydrogen content. For these reasons, it has great industrial value as a fuel. However, it is also gaining more recognition as a raw material for the production of commercially-important chemical products among which methanol is notable. BFG, on the other hand, is primarily a nitrogen-rich and carbon dioxide-rich product though its CO content is generally 4 to 5 times higher than the CO content of COG. COG’s higher heating value (HHV) is about 8–10 times higher than that of BFG. BFG is traditionally combusted for low-grade heat applications. As the world’s largest producer of steel, China is the most experienced country in dealing with the off- gases produced in steel plants.
[Show full text]
Electricity and Heat Annual Questionnaire 2013 and Historical Revisions
ELECTRICITY AND HEAT ANNUAL QUESTIONNAIRE 2013 AND HISTORICAL REVISIONS August 2014 Attached is the annual questionnaire for electricity and heat which provides for the submission of 2013 data and historical revisions where applicable. Administrations are requested to complete the questionnaire at the latest 30 of September 2014. Earlier submissions are welcome. Under the Energy Statistics Regulation - the submission deadline for the EU, the European Economic Area and the candidate countries reporting to the Commission of the European Communities is 30 November 2014. Please send your questionnaire to: • International Energy Agency (IEA/OECD), Energy Data Centre (the IEA will forward the data to the United Nations Economic Commission for Europe in Geneva). • Commission of the European Communities, Eurostat, Energy Statistics (for Member States of the European Union, EU Candidate Countries and EFTA Countries) • United Nations Statistics Division, Industry and Energy Statistics Section Transmission details are provided in the “Data communication procedures” section. ANNUAL ELECTRICITY QUESTIONNAIRE Data Communication Procedures IEA 9, rue de la Fédération, 75739, Paris, Cedex 15, France Please complete data for your country on the Energy Data Center: https://www.energydatacenter.org Alternatively send the questionnaire electronically to: [email protected] NOTE: For questions regarding the questionnaire, contact the above email address. * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * Eurostat Bâtiment Jean Monnet, Plateau du Kirchberg, L-2920, Luxembourg (for EU Member States , EU Candidate Countries and EFTA Countries) The completed questionnaire should be transmitted via the Single Entry Point (SEP) following the implementing procedures of eDAMIS (electronic Data files Administration and Management Information System). E-MAIL ADDRESS [email protected] NOTE For questions regarding the questionnaire, contact Mr.
[Show full text]
Energy Balance Guide Methodology Guide for the Construction of Energy Balances & Operational Guide for the Energy Balance Builder Tool
Energy balance guide Methodology guide for the construction of energy balances & Operational guide for the energy balance builder tool 31 January 2019 Table of Content Table of Content Introduction ................................................................................................................. 3 Why energy balances are constructed? .................................................................... 4 Prerequisites for the construction of energy balances ............................................ 6 General methodology aspects ................................................................................... 7 Products (columns of the energy balance) ............................................................. 11 Flows (rows of the energy balance) ........................................................................ 19 Complementing indicators ....................................................................................... 39 Examples of practical use ........................................................................................ 42 Consistency with IRES ............................................................................................. 43 The Eurostat's energy balance builder tool ............................................................ 49 Literature and information sources ......................................................................... 52 Energy balance guide 2 Introduction 1 Introduction Glossary & acronyms EDAMIS Electronic Data files Administration and Management Information
[Show full text]
Definition: a Solid Fossil Fuel Consisting of Carbonised Vegetal Matter
COAL Definition: A solid fossil fuel consisting of carbonised vegetal matter. Explanation: There are two main categories of coal, hard coal (comprising medium‐ and high rank coal)ls) and brown coal (low‐rank coal)ls) whic h can be ident ifie d by thiheir Gross ClCalor ific VlValue ‐ GCV and the Vitrinite mean Random Reflectance per cent ‐ Rr. The relationship between the coal types defined below is illustrated here: Hard Coal Anthracite Bituminous Coal Coking Coal Other Bituminous Coal Brown Coal Sub‐Bituminous Coal Lignite Remark: Peat is not included in the Coal group. Consultant’s comments For this definition and for those related to it the substance of the UNECE classification system for In‐Seam and Low‐Rank coals has been adopted. HARD COAL Definition: Coals with a gross calorific value (moist, ash‐free) basis which is not less than 24 MJ/kg or which is less than 24 MJ/kg provided that the coal has a Vitrinite mean Random Reflectance greater than, or equal to 060.6 per cent. Remark: Hard coal comprises Anthracite and Bituminous coals. Note that hard coal may include coals with a GCV ≥ 24 MJ/kg and a mean Rr < 0.6 per cent. ANTHRACITE Definition: A high‐rank, Hard Coal with a gross calorific value (moist, ash‐free basis) greater than, or equal to, 24 MJ/kg and a Vitrinite mean Random Reflectance greater than, or equal to 2.0 per cent. Explanation:It usually has less than 10% volatile matter, a high carbon content (about 86‐98% carbon) and is non‐agglomerating.
[Show full text]
Iron and Steel Industry
Office of Air and Radiation September 2012 AVAILABLE AND EMERGING TECHNOLOGIES FOR REDUCING GREENHOUSE GAS EMISSIONS FROM THE IRON AND STEEL INDUSTRY Available and Emerging Technologies for Reducing Greenhouse Gas Emissions from the Iron and Steel Industry Prepared by the Sector Policies and Programs Division Office of Air Quality Planning and Standards U.S. Environmental Protection Agency Research Triangle Park, North Carolina 27711 September 2012 Table of Contents Tables .............................................................................................................................................. v Figures............................................................................................................................................ vi Abbreviations and Acronyms ....................................................................................................... vii EPA Contact................................................................................................................................... ix I. Introduction ................................................................................................................................. 1 II. Purpose of this Document .......................................................................................................... 1 III. Organization of This Document................................................................................................ 1 IV. Description of the Iron and Steel Industry ...............................................................................
[Show full text]