Bias-Easy™ RBE-200 Bias Probe Instructions

Total Page：16

File Type：pdf, Size：1020Kb

Bias-Easy™ RBE-200 Bias Probe Instructions 1. Turn off your amp. 2. Insert the BLACK banana plug into the COM jack of your multimeter. 3. Insert the RED banana plug into the mA jack of your multimeter. 4. Set your multimeter switch to the mA range (most common is the 200mA range). If your meter is auto-ranging, set the switch to the mA setting. Important - do not move this selector switch once you plug the Bias-Easy™ probe into the tube socket of the amp. 5. Remove one of the power tubes (6L6, EL34, 5881, 6550, 6V6, KT66, KT77, etc) 6. Insert the Bias-Easy™ probe into the power tube socket, making sure to line up the key on the probe post with the key in the center hole of the socket. 7. Insert the tube you removed into the socket of the Bias-Easy™. Make sure the key on the tube base is properly lined up with the key on the center hold of the socket. The other power tube(s) must be in place in their sockets during testing. 8. Make certain that a speaker is connected to the amp. If this is an amp head, connect a cable between the speaker jack and the speaker cabinet. 9. Turn on the amp, allow to warm up, and turn the standby switch to "operate". 10. The meter should read the cathode current in milliamps (mA). If the current exceeds 100mA, be prepared to immediately turn the amp back to standby. You have a problem in the amp, or a defective tube. 11 Adjust the bias pot for the proper bias reading. A rule-of-thumb generic setting is about 35mA for 6L6 and EL34, 18mA for 6V6. A much more accurate setting is determined by knowing the plate voltage of the amplifier, and using that information along with the type of tubes (6L6, EL34, etc) on our online Tube Bias Calculator at www.amprepairparts.com/bias.htm. 12 Do not change the multimeter's selector switch while connected to the amplifier - meter damage may result. 13. Turn off the amp, allow the tubes to cool, remove the tube from the Bias-Easy™ socket, remove the socket from the amp, and remove the test leads from the meter. .

Copy Link

Recommended publications

Ronnie Earl for a Blackface Vibroverb Today? Surely Something North of $4,000
Mountainview Publishing, LLC INSIDE the The Truth… Rarely given, we know it when we hear it, and you The Player’s Guide to Ultimate Tone TM can only get it here… $15.00 US, December 2013/Vol.15 NO.2 Report The Kansas Tornado… Another immensely tone- Truth ful classic amp that went unclaimed “Three chords and the truth – that’s what a country song is.” – Willie Nelson Size matters… Pressure is being asked point-blank which guitar, amplifier or pickup to buy. This happens frequent- The Warehouse ly enough that we have learned to pose probing personal questions in search of an answer… Well, G15A Alnico what do you think you might want and why? We don’t always know what we want until we want it, Big Fifteen and we still couldn’t always tell you why. Sometimes the things that last seem to materialize out of no where with little forethought or insight, as if we were meant to have them, and that’s the truth. 4 Richard Goodsell and the evolution of the Goodsell Super 17 Our review of the Super 17 Mark IV 10 The Goodsell overdrive 10 John McGuire Guitars Our interview with John McGuire & review of the McGuire Tradition 14 The Eastwood Jupiter Pro… We also must confess that we don’t always understand what motivates guitar players when it Simply cool comes to choosing amplifiers today. This is nothing new – most of the amps we own are immensely in every way toneful classic keepers that were ignored by potential buyers due to stripped or recovered original cabinets or a replaced transformer.
[Show full text]
The EL34 Power Tube HI-'I
The EL34 Power Tube HI-'I .... o.l"r A lp Musical Evaluations of a Classic Design .... A_I . 4.551 Single. Ended EL·84 Stereo Amp ~ _ .... ,��\� . -""" ".. - ...-., p.,.��",-, �. 1""""' -�,�.. � . oPf' ' ".".. ._ '" "'� .,_ "'�•• '" "'� ...- ' ,t\1".' ,w ' � "'\)U'�..,. ,\ 1\ ' ��-;---""\.\. ",.-" " ".,... "", ""�_ " tt"�" ,....-" ...........,...1"'" '�" ""t\1 _,.,.""" ....'" 'r·\ �'� . � ......,. �,,,. � ,..' ",...., \PJOl8'i .... �,�oPf',.,....;:.. O\ �,cl\ ., .... " , � ...,,.. AA �r- . · :::- ,,<,<, ,. ..""'"':k ...0'\1. � ':;: "",;: .. .._ " r ,...,.. _ "" " .-;.,,...""".... ",.... ......,.,.,,, -;;. ,... :;..,� _ """;.... -� . 0 """ " . ,,..,. ,t" ,,'" <""" , .-_,.;.;.''' � .. '''''''-o<f' _ ....;;; .,;::; , -- '" " ,.,...,.. "" .'" ::, ,t"� ��. ...,.,..,.;.;."1"" ''/'''' � _.� "" f"'� . � ' M'''" ' "- """",,; ,.of .,.,..� .. ...,. ' "' 1" '". '_1"""' . .. " ,,,,,,,,,,,,,,,_ f"""";""';..::: .,... " '�,;;.;:' ' ......,,..,..,. _-:: -__':1oPf' ::;;'", --''''"", ""","" ", ' �':::', � ' ""r; """"-"' .''''''''�}.. ,t\1 \ �·, � ot ,;: "" � ,.,. ---� , _.at" � t\JV" �� 'i"'f'- " .::... .. .... �. , ,�,....,.' .....;. _ ...-:> ".... JC8'I\\ -, \�..- WOl\ """,.""''1"'"- �""'" � '-,�� 6<1\"""- ' ""'..,... � ...... � 6U'." �. - ,t\1 , . _ , "'" 1J>b\"� ��, oPf''' .,..-._ " "" .0. " ..... ��_��\t"�'".. ' ....... "" "",",. N ��:L [\l\'J � ��i y< • D T 0 • , 5 P A G • A N D N D u 5 T • y N • w 5 Beware of FakeNOS Tubes! CE Distribution US Distributor for Electronic Tubes VTV Issue # 1 6 JJ Over the last year or so, we have JJ Electronic,
[Show full text]
Operation, Tetrode, Pentode in the Single-Ended, Class-A
10-76 10. Guitar Amplifiers 10.5.1 Single-ended (class A)-operation, tetrode, pentode In the single-ended, class-A power-stage, one (single) power-tube operates in common- cathode configuration with the output transformer being part of the plate circuit (transformer- coupling). Without AC-drive (“quiescent state”), a stable balance appears – it is called the operating point (OPP). The characteristics shown in Fig. 10.5.2 yield an OPP at 250 V and 48 mA, if a voltage of -7.5 V between (control) grid (g1) and cathode is chosen. This can be done e.g. by using a cathode-resistor of 142 Ω. The cathode-current (the sum of the 48-mA- plate-current and the 5-mA-screen-grid-current) will then generate a positive cathode-voltage of + 7.5 V (relative to ground). With the control-grid at ground-potential (Ug1 = 0) a control- grid-to-cathode-voltage of -7.5 V results (i.e. the control grid is negative vs. the cathode). Fig. 10.5.2: Output characteristics of the EL84, power-stage circuit (single-ended class-A operation). AP = OPP As a drive signal appears (Ug1 ≠ 0), plate-voltage and –current change. As a first approach, it will be sufficient to consider the transformer in the plate-circuit as a large inductance connected in parallel with an ohmic resistor (Chapter 10.6). In this model we have only pure DC flowing through the inductance, and only pure AC flowing through the resistor. With a drive-signal present, the Ua/Ia-point will move along the load-line given in Fig.
[Show full text]
Push - Pull Audiophile - Output (1608-1650 "A" Series)
Push - Pull Audiophile - Output (1608-1650 "A" Series) PUSH - PULL "EASY HOOK-UP" "CLASSIC" TUBE TYPE - ULTRA-LINEAR OUTPUT TRANSFORMERS • NEW & Improved version of our 1608-1650 series output transformers (re-designed secondaries for easy hook- up of secondary loads) • Designed for push-pull tube output circuits. o • Enclosed (shielded), 4 slot, above chassis Type "X" mounting. • Frequency response 30 Hz. to 30 Khz. at full rated power (+/- 1 db max. - ref. 1 Khz) minimum. Except the Audi 1650E (70 Hz. to 30 Khz. +/- 1 db max. - ref. 1 Khz.) be • Insulated flexible leads 8" min. • All units (except the 1650G) include 40% screen taps for Ultra-Linear operation (if desired). Tu • Typical applications - Push-Pull: triode, Ultra-Linear pentode, and tetrode connected audio output. The 1650G does NOT have primary screen taps and will not support "Ultra-Linear" applications. Audio Dimensions (Inches) Part Primary Max. DC Secondary Wt. Watts E G Number Impedance Per Side Impedance A B C D Lbs. (RMS) +/- 1/16” Slot 1608A 10 8,000 C.T. 100 ma. 4-8-16 2.50 2.75 3.06 2.00 1.69 .203 x .38 2.5 1609A 10 10,000 C.T. 100 ma. 4-8-16 2.50 2.75 3.06 2.00 1.69 .203 x .38 2.5 1615A 15 5,000 C.T. 100 ma. 4-8-16 2.50 3.25 3.06 2.00 2.19 .203 x .38 3.25 1650E 15 8,000 C.T. 100 ma. 4-8-16 2.50 3.25 3.06 2.00 2.50 .203 x .38 3.5 1620A 20 6,600 C.T.
[Show full text]
Bias-Easy 1200™ Bias Tester Instructions
Bias-Easy 1200™ Bias Tester Instructions 1. Turn off your amp, and allow to cool down. The Bias-Easy 1200™ is primarily for amplifiers using four 8-pin power tubes with a bias adjustment potentiometer available inside or on the chassis underside or back panel of the amp. 2. Remove one of the power tubes (6L6, EL34, 5881, 6550, 6V6, KT66, KT77, etc) 3. Insert a Bias-Easy™ probe into the power tube socket, making sure to line up the key on the probe post with the key in the center hole of the socket. Repeat for the second, third and fourth power tubes with each of the remaining probes. If your amp only has two power tubes, we suggest using the A and B probes. The C and D probes may be unplugged from the Bias-Easy™ in that case. 4. Insert each tube you removed into each socket of the Bias-Easy™. Make sure the key on the tube base is properly lined up with the key on the center hole of the socket. All power tube(s) must be in place in their sockets during testing. 5. Make certain that a speaker is connected to the amp. If this is an amp head, connect a cable between the speaker jack and the speaker cabinet. 6. Make sure all bias probes to be used in the testing are connected to the jacks at the top of the Bias-Easy™. Connect the power supply cord to the jack on the bottom of the Bias-Easy™, and connect the USB connector on the cord to the power supply.
[Show full text]
Tube Output (10 - 280 Watts) (1608-1650 Series) - Hammond Mfg
9/6/2021 Tube Output (10 - 280 Watts) (1608-1650 Series) - Hammond Mfg. Quality Products. Service Excellence. Tube Output (10 - 280 Watts) 1608-1650 Series Push-Pull - HI-FI Features Please see our NEW & improved versions (easy wire secondary series). Designed for push-pull tube output circuits. Enclosed (shielded), 4 slot, above chassis Type "X" mounting. Frequency response 30 Hz. to 30 Khz. at full rated power (+/- 1 db max. - ref. 1 Khz) minimum. Insulated flexible leads 8" min. Manufactured with plastic coil forms for coil support and insulation. Typical applications - Push-Pull: triode, Ultra-Linear pentode, pentode and tetrode connected audio output. Due to the unique interleaving of the windings BOTH secondary windings must be engaged to meet specifications (see hook-up diagrams below). For the "ultimate" in Push-Pull output see our line of epoxy potted output transformers. 1645 Only Secondary Connections (Due to the unique interleaving of the windings BOTH secondary windings must be engaged to meet specifications) To hook up 4/8/16 ohm secondary loads - see schematic (do not use the white wire). To hook up secondary to 70V loads, jumper Blk/Yel wire to Grn wire. Connect load to Blk and White wires. Gallery Audio Primary Maximum Secondary Dimensions Watts Impedance DC Impedance E G Weight Part No. (RMS) (Ohms) Per Side (Ohms) A B C D +/- 1/16" Slot (lbs.) https://www.hammfg.com/electronics/transformers/classic/1608-1650 1/2 9/6/2021 Tube Output (10 - 280 Watts) (1608-1650 Series) - Hammond Mfg. Audio Primary Maximum Secondary Dimensions Watts Impedance DC Impedance E G Weight Part No.
[Show full text]
The 18 Watt Amp Builder's Guide
The 18 Watt Amp Builder's Guide April 2018, Version 3.0 For the sole personal use of Trinity Amps Customers. Parts © Trinity Amps 2005 - 2017 www.trinityamps.com Trinity Amps 18 Watt Builder’s Guide. Version 3.0 Page - 2 Table of Contents Table of Contents .................................................................................................................................................. 3 Thank You! ............................................................................................................................................................ 5 Introduction .......................................................................................................................................................... 7 Acknowledgements ............................................................................................................................................... 7 WARNING............................................................................................................................................................ 8 Version Control ..................................................................................................................................................... 9 Fender and Marshall Tone controls ..................................................................................................................................................... 13 VOX Tone controls ...............................................................................................................................................................................
[Show full text]
Easy Wire Secondary 1608A-1650A Series Push-Pull - HI-FI
9/6/2021 Tube Output (10 - 280 Watts) Easy Wire Secondary (1608A-1650A Series) - Hammond Mfg. Quality Products. Service Excellence. Tube Output (10 - 280 Watts) Easy Wire Secondary 1608A-1650A Series Push-Pull - HI-FI Features NEW & improved version of our 1608-1650 Series multiple secondary output transformers (re-designed secondaries for easy hook-up of secondary loads). Designed for push-pull tube output circuits. Units are designed to provide ample "headroom" at bass frequencies (note the weight of each transformer). All models have a secondary tapped for 4, 8 or 16 ohm outputs. Enclosed (shielded), 4 slot, above chassis Type "X" mounting. Manufactured with plastic coil forms for coil support and insulation. Frequency response 30 Hz. to 30 Khz. at full rated power (+/- 1 db max. - ref. 1 Khz) minimum. Insulated flexible leads 8" min. All units (except the 1650G) include 40% screen taps for Ultra-Linear operation (if desired). Typical applications - Push-Pull: triode, Ultra-Linear pentode, pentode and tetrode connected audio output. The 1650G does NOT have primary screen taps and will not support "Ultra-Linear" applications. Gallery Audio Primary Maximum Secondary Dimensions Watts Impedance DC Impedance E G Weight Part No. (RMS) (Ohms) Per Side (Ohms) A B C D +/- 1/16" Slot (lbs.) 1608A 10 8,000 ct 100 ma. 4-8-16 2.50 2.75 3.06 2.00 1.69 0.20 x 0.38 2.5 1609A 10 10,000 ct 100 ma. 4-8-16 2.50 2.75 3.06 2.00 1.69 0.20 x 0.38 2.5 1615A 15 5,000 ct 100 ma.
[Show full text]
YJS-Triode Instruction Sheet
Designed by ® Designed by ® Designed by ® Designed by ® Designed by ® Yellow Jackets® Yellow Jackets® Yellow Jackets® Yellow Jackets® Yellow Jackets® Tube Converter Tube Converter Tube Converter Tube Converter Tube Converter YJS Triode YJS Triode YJS Triode YJS Triode YJS Triode Includes EL84 Power Tubes Includes EL84 Power Tubes Includes EL84 Power Tubes Includes EL84 Power Tubes Includes EL84 Power Tubes Handmade in the U.S.A. Handmade in the U.S.A. Handmade in the U.S.A. Handmade in the U.S.A. Handmade in the U.S.A. Yellow Jackets® Yellow Jackets® Yellow Jackets® Yellow Jackets® Yellow Jackets® • Converts most audio amplifiers with 6L6s, EL34s, 6550s • Converts most audio amplifiers with 6L6s, EL34s, 6550s • Converts most audio amplifiers with 6L6s, EL34s, 6550s • Converts most audio amplifiers with 6L6s, EL34s, 6550s • Converts most audio amplifiers with 6L6s, EL34s, 6550s or 6V6s to EL84s without modification or rebiasing or 6V6s to EL84s without modification or rebiasing or 6V6s to EL84s without modification or rebiasing or 6V6s to EL84s without modification or rebiasing or 6V6s to EL84s without modification or rebiasing • Converts from Class AB Pentode to Class A Triode! • Converts from Class AB Pentode to Class A Triode! • Converts from Class AB Pentode to Class A Triode! • Converts from Class AB Pentode to Class A Triode! • Converts from Class AB Pentode to Class A Triode! • Drops output power by 70% to 90%. • Drops output power by 70% to 90%. • Drops output power by 70% to 90%. • Drops output power by 70% to 90%. • Drops output power by 70% to 90%.
[Show full text]
Yjshort Instruction Sheet
Designed by ® Designed by ® Designed by ® Designed by ® Designed by ® Yellow Jackets® Yellow Jackets® Yellow Jackets® Yellow Jackets® Yellow Jackets® Tube Converter Tube Converter Tube Converter Tube Converter Tube Converter YJShort YJShort YJShort YJShort YJShort Includes EL84 Power Tubes Includes EL84 Power Tubes Includes EL84 Power Tubes Includes EL84 Power Tubes Includes EL84 Power Tubes Handmade in the U.S.A. Handmade in the U.S.A. Handmade in the U.S.A. Handmade in the U.S.A. Handmade in the U.S.A. Yellow Jackets® Yellow Jackets® Yellow Jackets® Yellow Jackets® Yellow Jackets® • Converts most audio amplifiers with 6L6s, EL34s, • Converts most audio amplifiers with 6L6s, EL34s, • Converts most audio amplifiers with 6L6s, EL34s, • Converts most audio amplifiers with 6L6s, EL34s, • Converts most audio amplifiers with 6L6s, EL34s, 6550s or 6550s or 6550s or 6550s or 6550s or 6V6s to EL84s without modification or rebiasing. 6V6s to EL84s without modification or rebiasing. 6V6s to EL84s without modification or rebiasing. 6V6s to EL84s without modification or rebiasing. 6V6s to EL84s without modification or rebiasing. • Converts from Class AB to Class A operation! • Converts from Class AB to Class A operation! • Converts from Class AB to Class A operation! • Converts from Class AB to Class A operation! • Converts from Class AB to Class A operation! • Drops output power by 50% to 70%. • Drops output power by 50% to 70%. • Drops output power by 50% to 70%. • Drops output power by 50% to 70%. • Drops output power by 50% to 70%. • Safe for all common amplifiers and transformers. • Safe for all common amplifiers and transformers.
[Show full text]
Antique Electronic Supply Tube Prices 2019
ANTIQUE ELECTRONIC SUPPLY TUBE PRICES 2019 201A - Triode, Low-MU, Globe -Long Pin $54.10 2A3 - Triode, Power Amp, Single Plate - Used $263.85 201A - Triode, Low-MU, Globe - Used $27.05 2A5 - Pentode, Power Amplifier $21.90 0A2/150C2 - Voltage Reg, Diode, Glow $6.90 2A5 - Pentode, Power Amplifier - Used $11.65 0A3/VR75 - Voltage Regr, Diode, Glow $6.90 2A6 - Diode, Dual - Triode $7.90 0B2 - Voltage Reg, Diode, Glow $5.90 2A7 - Pentagrid Converter $9.90 0B3/VR90 - Voltage Regulator $3.90 2C22/7193 - Triode $8.05 0C2 - Voltage Regulator $8.90 2D21/PL21 - Thyratron $6.90 0C3-A/VR105 - Voltage Regulator $6.90 2E5 - Indicator, ST Shape Glass $14.35 0D3-A/VR150 - Voltage Regulator $6.15 2E5 - Indicator, Tubular Glass $14.35 0G3/85A2 - Voltage Regulator $3.30 2E24 - Beam Power Amplifier $8.70 0Z4-A - Rectifier, Full Wave, Gas $3.90 2E26 - Pentode, Beam $6.90 1A5GT - Pentode, Power Amplifier $4.90 2X2A/2Y2_879 - Rectifier $2.66 1A7GT - Pentagrid Converter $4.90 3A4 - Pentode, Power Amplifier $5.90 1AD4 - Pentode $4.45 3A5/DCC90 - Triode, Dual $5.90 1C5GT - Pentode, Power Amplifier $3.65 3AV6 - Diode, Dual - Triode $3.55 1G4GT - Triode, Medium MU $14.90 3B28 - Rectifier, Half Wave $29.00 1H4G - Triode, Medium MU $15.90 3C24/24G - Triode $19.90 1H5GT-G - Diode - Triode, High MU $3.90 3Q4 - Pentode, Power $5.90 1H6G - Diode, Dual - Triode $2.85 3Q5GT - Pentode, Beam Power $4.90 1J6G - Triode, Dual, Power Amplifier $7.55 3S4 - Tetrode, Beam Power $4.90 1L4/DF92 - Pentode $2.67 3V4/DL94 - Pentode, Power $8.90 1L6 - Heptode $99.90 4-125A/4D21 - Tetrode,
[Show full text]
YJC Instruction Sheet
Designed by ® Designed by ® Designed by ® Designed by ® Designed by ® Yellow Jackets® Yellow Jackets® Yellow Jackets® Yellow Jackets® Yellow Jackets® Tube Converter Tube Converter Tube Converter Tube Converter Tube Converter YJC YJC YJC YJC YJC Includes EL84 Power Tubes Includes EL84 Power Tubes Includes EL84 Power Tubes Includes EL84 Power Tubes Includes EL84 Power Tubes Handmade in the U.S.A. Handmade in the U.S.A. Handmade in the U.S.A. Handmade in the U.S.A. Handmade in the U.S.A. Yellow Jackets® Yellow Jackets® Yellow Jackets® Yellow Jackets® Yellow Jackets® • Converts most audio amplifiers with 6L6s, EL34s, • Converts most audio amplifiers with 6L6s, EL34s, • Converts most audio amplifiers with 6L6s, EL34s, • Converts most audio amplifiers with 6L6s, EL34s, • Converts most audio amplifiers with 6L6s, EL34s, 6550s or 6V6s to EL84s without modification or 6550s or 6V6s to EL84s without modification or 6550s or 6V6s to EL84s without modification or 6550s or 6V6s to EL84s without modification or 6550s or 6V6s to EL84s without modification or rebiasing. rebiasing. rebiasing. rebiasing. rebiasing. • Connects to chassis-ground for cathode-biased • Connects to chassis-ground for cathode-biased • Connects to chassis-ground for cathode-biased • Connects to chassis-ground for cathode-biased • Connects to chassis-ground for cathode-biased amps. amps. amps. amps. amps. • Converts from Class AB to Class A operation! • Converts from Class AB to Class A operation! • Converts from Class AB to Class A operation! • Converts from Class AB to Class A operation! • Converts from Class AB to Class A operation! • Drops output power by 50% to 70%.
[Show full text]