DOCSLIB.ORG

710-730 Series Bolt Style Hermetic Filters

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text

Load more

710-730 Series Bolt Style Instec is now part of TTE Filters. Hermetic Filters Please contact TTE for assistance at +1-716-532-2234, [email protected] or www.tte.com. Instec Bolt Style Hermetic Filters are ideal for applications where high performance is critical and a threaded mounting technique is desired. A wide range of electrical characteristics provide effective solutions to many filtering applications. Filters are available in C, L1, L2, PI, T, and Double-T configurations and offer predictable insertion loss over the frequency range. With the more complex circuits, steeper cut offs can be obtained. These bolt style filters and matching hardware are silver plated for better conductivity and superior performance. Features: Utilizes MLC discoidal capacitors, the heart of the filter Silver plated case and hardware offer excellent conductivity Infinite paths to ground within the capacitor allow for lowest impedance to ground available Full part number and date code marking, custom marking available on request Designed and can be tested to MIL-PRF-28861 requirements Rated to 15 Amps. Higher Current ratings available as non-hermetic designs Standard lug leads, others available on request 375 case (1/4-28 UNF-2A thread) and 690 case (5/16-24 UNF-2A thread) Custom configurations also available—contact factory Applications: Secure Military Communications Power supplies Medical equipment Mining and oil exploration Signal lines Instec Filters ◊ 7426A Tanner Parkway ◊ Arcade, NY 14009 716.307.8542 ◊ FAX: 805.687.8085 www.instec-filters.com ◊ [email protected] 710-730 Series Bolt Style Instec is now part of TTE Filters. Hermetic Filters Please contact TTE for assistance at +1-716-532-2234, [email protected] or www.tte.com. 710 Series .375” OD (1/4”-25 UNF-2A) Bolt Style Filters: How to Order: 714 -- 503 B P A B 2 ** 710= C-filter placeholder Capacitance code in Voltage rating Length (Max) Current Thread Terminal Special requirements 711= L1-filter PF, 1st 2 digits are A=50VDC A=0.793” rating length length (to be assigned 712= L2-filter significant, 3rd B=100VDC B=0.761” 1=1 AMP A=0.187” 1=0.160” by the factory) 713= PI-filter digit is number of C=200VDC C=0.770” 2=2 AMP D=0.312” 2=0.250” 714= T-filter zeros D=300VDC D=special 3=3 AMP 715= Double-T-filter P tolerance assumed E=400VDC 4=4 AMP unless specified J=500VDC 5=5 AMP A=10 AMP B=15 AMP Maximum Cap Values: The below table gives the maximum cap values available and typical Insertion Loss performance by voltage rating: 710 Series .375" Bolt C-Filter Rated Voltage----> 50V 100V 200V 300V 400V 500V Max Capacitance (µF) P tolerance assumed 10 8 6 4.8 3 1.5 Typical Insertion Loss (dB) 30KHz 30 29 26 25 21 15 150KHz 45 43 41 39 35 28 300KHz 51 49 47 45 41 35 1MHz 61 59 57 55 51 45 10MHz >70 >70 >70 >70 69 63 100MHz >70 >70 >70 >70 >70 >70 1GHz >70 >70 >70 >70 >70 >70 Instec Filters ◊ 7426A Tanner Parkway ◊ Arcade, NY 14009 716.307.8542 ◊ FAX: 805.687.8085 www.instec-filters.com ◊ [email protected] 710-730 Series Bolt Style Instec is now part of TTE Filters. Hermetic Filters Please contact TTE for assistance at +1-716-532-2234, [email protected] or www.tte.com. 711 Series .375" Bolt L1-Filter Rated Voltage----> 50V 100V 200V 300V 400V 500V Max Capacitance (µF) P tolerance assumed 7 5 4 3.2 2 0.8 Typical Insertion Loss (dB) 30KHz 28 25 24 21 17 9 150KHz 42 39 37 35 31 23 300KHz 48 45 43 41 37 29 1MHz 58 55 54 51 45 39 10MHz >70 >70 >70 >70 65 58 100MHz >70 >70 >70 >70 >70 >70 1GHz >70 >70 >70 >70 >70 >70 712 Series .375" Bolt L2-Filter Rated Voltage----> 50V 100V 200V 300V 400V 500V Max Capacitance (µF) P tolerance assumed 7 5 4 3.2 2 0.8 Typical Insertion Loss (dB) 30KHz 28 25 24 21 17 9 150KHz 42 39 37 35 31 23 300KHz 48 45 43 41 37 29 1MHz 58 55 54 51 45 39 10MHz >70 >70 >70 >70 65 58 100MHz >70 >70 >70 >70 >70 >70 1GHz >70 >70 >70 >70 >70 >70 713 Series .375" Bolt PI-Filter Rated Voltage----> 50V 100V 200V 300V 400V 500V Max Capacitance (µF) P tolerance assumed 7 5 4 3.2 2 0.8 Typical Insertion Loss (dB) 30KHz 28 27 23 21 17 9 150KHz 40 37 35 35 31 23 300KHz 48 45 43 41 37 30 1MHz 58 55 53 51 47 40 10MHz >70 >70 >70 >70 >70 51 100MHz >70 >70 >70 >70 >70 >70 1GHz >70 >70 >70 >70 >70 >70 Instec Filters ◊ 7426A Tanner Parkway ◊ Arcade, NY 14009 716.307.8542 ◊ FAX: 805.687.8085 www.instec-filters.com ◊ [email protected] 710-730 Series Bolt Style Instec is now part of TTE Filters. Hermetic Filters Please contact TTE for assistance at +1-716-532-2234, [email protected] or www.tte.com. 714 Series .375" Bolt T-Filter Rated Voltage----> 50V 100V 200V 300V 400V 500V Max Capacitance (µF) P tolerance assumed 7 5 4 3.2 2 0.8 Typical Insertion Loss (dB) 30KHz 28 25 23 21 17 10 150KHz 42 39 37 35 31 23 300KHz 48 45 43 41 37 30 1MHz 58 56 53 51 47 39 10MHz >70 >70 >70 >70 65 57 100MHz >70 >70 >70 >70 >70 >70 1GHz >70 >70 >70 >70 >70 >70 715 Series .375" Bolt Double-T-Filter Rated Voltage----> 50V 100V 200V 300V 400V 500V Max Capacitance (µF) P tolerance assumed 7 5 4 3.2 2 0.8 Typical Insertion Loss (dB) 30KHz 30 27 25 23 20 11 150KHz 44 41 39 37 33 25 300KHz 50 47 45 43 39 30 1MHz 57 55 55 53 48 41 10MHz >70 >70 >70 >70 >70 50 100MHz >70 >70 >70 >70 >70 >70 1GHz >70 >70 >70 >70 >70 >70 Typical Insertion Loss Performance of Common Filters: Insertion Loss (dB) Cap Value Voltage Instec P/N Type (µF) Rating 30KHz 150KHz 300KHz 1MHz 10MHz 100MHz 1GHz 710-105B C-Filter 1.0 100VDC 13 27 33 43 62 >70 >70 710-133J C-Filter 0.013 500VDC 7 26 45 65 710-405B C-Filter 4.0 100VDC 20 34 39 50 60 >70 >70 711-145B L1-Filter 1.4 100VDC 15 28 33 44 60 >70 >70 712-255B L2-Filter 2.5 100VDC 21 34 39 50 60 >70 >70 713-155A PI-Filter 1.5 50VDC 15 28 34 40 52 >70 >70 713-605A PI-Filter 6.0 50VDC 28 42 48 58 >70 >70 >70 714-245B T-Filter 2.4 100VDC 11 18 33 70 >70 >70 714-254C T-Filter 0.25 200VDC 21 34 40 50 >70 >70 >70 715-205B TT-Filter 2.0 100VDC 20 33 39 48 >70 >70 >70 Instec Filters ◊ 7426A Tanner Parkway ◊ Arcade, NY 14009 716.307.8542 ◊ FAX: 805.687.8085 www.instec-filters.com ◊ [email protected] 710-730 Series Bolt Style Instec is now part of TTE Filters. Hermetic Filters Please contact TTE for assistance at +1-716-532-2234, [email protected] or 730 Series .690” OD (5/16”-24 UNF-2A) Bolt Style Filters: www.tte.com. How to Order: 733 -- 503 B P A B 2 ** 730= C-filter placeholder Capacitance code in Voltage rating Length (Max) Current Thread Terminal Special requirements 731= L1-filter PF, 1st 2 digits are A=50VDC A=0.793” rating length length (to be assigned 732= L2-filter significant, 3rd B=100VDC B=0.761” 1=1 AMP A=0.187” 1=0.160” by the factory) 733= PI-filter digit is number of C=200VDC C=0.770” 2=2 AMP D=0.312” 2=0.250” 734= T-filter zeros D=300VDC D=special 3=3 AMP 735= Double-T-filter P tolerance assumed E=400VDC 4=4 AMP unless specified J=500VDC 5=5 AMP G=1000VDC A=10 AMP B=15 AMP Maximum Cap Values: The below table gives the maximum cap values available and typical Insertion Loss performance by voltage rating: 730 series .690" Bolt C-Filter Rated Voltage---> 50 100 200 300 400 500 1000 Max Capacitance (µF) P tolerance assumed 35 30 24 18 12 11 4 Typical Ins Loss 30KHz 44 43 41 38 34 33 24 150KHz 58 56 54 52 49 48 38 300KHz 64 62 60 58 54 53 44 1MHz >70 >70 70 68 65 64 54 10MHz >70 >70 >70 >70 >70 >70 >70 100MHz >70 >70 >70 >70 >70 >70 >70 1GHz >70 >70 >70 >70 >70 >70 >70 Instec Filters ◊ 7426A Tanner Parkway ◊ Arcade, NY 14009 716.307.8542 ◊ FAX: 805.687.8085 www.instec-filters.com ◊ [email protected] 710-730 Series Bolt Style Instec is now part of TTE Filters. Hermetic Filters Please contact TTE for assistance at +1-716-532-2234, [email protected] or www.tte.com. 731 series .690" Bolt L1-Filter Rated Voltage---> 50 100 200 300 400 500 1000 Max Capacitance (µF) P tolerance assumed 24 20 15 12 8 7 2.5 Typical Ins Loss 30KHz 41 39 37 34 31 30 21 150KHz 54 53 51 49 45 44 35 300KHz 60 59 57 54 51 50 41 1MHz 70 69 67 65 61 60 51 10MHz >70 >70 >70 >70 >70 >70 70 100MHz >70 >70 >70 >70 >70 >70 >70 1GHz >70 >70 >70 >70 >70 >70 >70 732 series .690" Bolt L2-Filter Rated Voltage---> 50 100 200 300 400 500 1000 Max Capacitance (µF) P tolerance assumed 24 20 15 12 8 7 2.5 Typical Ins Loss 30KHz 41 39 37 34 31 30 21 150KHz 54 53 51 49 45 44 35 300KHz 60 59 57 54 51 50 41 1MHz 70 69 67 65 61 60 51 10MHz >70 >70 >70 >70 >70 >70 70 100MHz >70 >70 >70 >70 >70 >70 >70 1GHz >70 >70 >70 >70 >70 >70 >70 733 series .690" Bolt PI-Filter Rated Voltage---> 50 100 200 300 400 500 1000 Max Capacitance (µF) P tolerance assumed 24 20 15 12 8 7 2.5 Typical Ins Loss 30KHz 41 39 37 35 31 30 21 150KHz 54 53 51 48 45 44 35 300KHz 60 59 57 54 51 50 41 1MHz 67 66 65 63 60 59 51 10MHz >70 >70 >70 >70 >70 >70 >70 100MHz >70 >70 >70 >70 >70 >70 >70 1GHz >70 >70 >70 >70 >70 >70 >70 Instec Filters ◊ 7426A Tanner Parkway ◊ Arcade, NY 14009 716.307.8542 ◊ FAX: 805.687.8085 www.instec-filters.com ◊ [email protected] 710-730 Series Bolt Style Instec is now part of TTE Filters.
Recommended publications
  • Table of Contents

    Table of Contents

    TABLE OF CONTENTS SECTION PAGE(S) 2 BEARINGS/ BUSHINGS GENERAL APPLICATION DATA / HP & OHC REPAIR 1 - 58 SET CONTENTS 59 - 78 COMPONENT LISTING 79 - 92 PROGRESSIVE LISTING BY HOUSING BORE 93 - 100 CAM BEARING TOOL - 101 OVERHEAD CAM REPAIR BEARING APPLICATIONS 103 - 112 SYSTEM INSTALLATION TOOLS / ACCESSORIES 113 - 118 Although the information in this catalog has been gathered from the best available sources and every possible effort has been made to ensure accuracy, we cannot accept responsibility for any errors or omissions. We would very much appreciate being advised of any inaccuracies which might come to your attention. Dura-Bond reserves the right to update and change product specifications at any time without notice. This catalog contains parts information only. Before installing any part listed, consult the appropriate vehicle manufacturer's instructional manual for detailed installation instructions. WARRANTY Dura-Bond Bearing Company products are warranted to be free from defects of materials or workmanship for one year from the date of purchase. Dura-Bond Bearing Company's responsibility is limited to the replacement value of the product if Dura-Bond determines the product to be defective under normal use and service. Claims for labor or related component cost will not be considered. No other warranty, either expressed or implied, is made. If you have a product need, we invite you to inquire. Check with us regarding all of your sleeve bearings, valve seats, and shim needs. *TRANSMISSION PIECES *MOTORCYCLES *MARINE APPLICATIONS *INDUSTRIAL APPLICATIONS *ANTIQUE VEHICLES *BUSHINGS Copywriter, Editor - Dennis O'leary Copywriter, Editor, Design Layout - William Dolak © 2001 DURA-BOND BEARING COMPANY ALL RIGHTS RESERVED.
  • Feb-Mar 2008

    Feb-Mar 2008

    The National Bowling Association, Inc. Volume 2, Issue 2 News 2007/2008 Submission deadline for events related to CBS Leagues/Members and/or High Scores for publication in the Newsletter Senate Officers must be received by Beverly Houston by the 15th of each month via email [email protected]. Clarence Dixon, President (773) 374-1360 Darryl “Spyder” Houston, Vice-Pres. The National Bowling Association (773) 406-8435 Mattie Miller, Secretary 67th Annual Championship Tournament—Reno, NV (773) 488-1405 [email protected] Final Entries Close Midnight, March 1, 2008 Rebecca Mack, Assistant Secretary Lawannah Hammond, Treasurer ALL TEAM, SINGLES & DOUBLES EVENTS 2007/2008 NATIONAL BOWLING STADIUM Senate Committee 300 N. CENTER STREET, RENO, NV 89501 Chairpersons Awards Mattie Miller JIM D. ALSTON MIXED DOUBLES EVENT Audit Lynne M. Martin COCONUT BOWL Constitution 1855 E. LINCOLN WAY, SPARKS, NV 89434 Bertha Fuller Family Picnic for more information or to download tournament entry forms Go to http://www.tnbainc.org/ Craig “Scooby” Wedgeworth Field Representative Sheri “Spiffy” Jones Owen O. Washington Scholarship Award Program Historian Evelyn Porter The National Bowling Association, Inc. annually offers $10,000 in scholarships to high school seniors. Prizes are Junior Bowling Program offered to three males and three females—with 1st place, $1,500; 2nd place $1,250; and 3rd place $1,000. Five Beverly Houston King/Queen Program (5) Book Scholarships of $500 each are offered to both male and female students. Henry Johnson Applications submitted for the Owen O. Washington Scholarship are automatically considered for the Chicago Membership Darryl “Spyder” Houston Bowling Senate’s Scholarship Awards.
  • Environmental Study of Airborne Particulate Matter in Mesabi Iron

    Environmental Study of Airborne Particulate Matter in Mesabi Iron

    Minnesota Taconite Workers Health Study: Environmental Study of Airborne Particulate Matter in Mesabi Iron Range Communities and Taconite Processing Plants — Mesabi Iron Range Community Particulate Matter Collection and Gravimetric Analysis Submitted by: Stephen D. Monson Geerts1, George Hudak 1, Virgil Marple2, Dale Lundgren3, Lawrence Zanko1, and Bernard Olson2 1Natural Resources Research Institute, University of Minnesota Duluth 2Department of Mechanical Engineering, University of Minnesota Twin Cities 3 University of Florida - Gainesville December 2019 Date: December 2019 Report Number: NRRI/RI-2019/30 – – Project No. 1806-10416-20080 NRRI Report of Investigation Investigation of Report NRRI Duluth Laboratories & Administration 5013 Miller Trunk Highway Duluth, Minnesota 55811 Coleraine Laboratories One Gayley Avenue P.O. Box 188 Coleraine, Minnesota 55722 Visit our website for access to this and other Natural Resources Research Institute publications: http://www.nrri.umn.edu/publications. Cover Photo Caption: Mesabi Iron Range community ‘rooftop’ particulate matter sample and data collection setup – Keewatin Elementary School – Keewatin, Minnesota. Recommended Citation: Monson Geerts, S.D., Hudak, G., Marple, V., Lundgren, D., Zanko, L., and Olson, B. 2019. Minnesota Taconite Workers Health Study: Environmental Study of Airborne Particulate Matter in Mesabi Iron Range Communities and Taconite Processing Plants: Mesabi Iron Range Community Particulate Matter Collection and Gravimetric Analysis. Natural Resources Research Institute,
  • Repair Services CATALOG

    Repair Services CATALOG

    Repair services CATALOG 1 ACTIONS TAKEN TO Made by anyone. DIAGNOSE PROBLEMS: • Your equipment is thoroughly cleaned to remove all Repaired by us. contamination A single source for repairs • Diagnostic tests are used to locate any inoperative components Meet your repair needs quickly and conveniently. You’ll find quality in every step of our repair process, whether the item is repaired at our Rockwell • Circuit analysis isolates Automation repair facilities, or through our strategic suppliers. marginal components As the original equipment manufacturer of Allen-Bradley® products and • Aged as well as marginal Reliance Electric™ drives, we are your single source for service, providing components are replaced repair on thousands of types and brands of electrical, electronic, to support long-term mechanical, servo and robotic products. performance of the unit BENEFITS • State-of-the-art equipment verifies total circuit board • REPAIR SAVINGS: Decrease service costs by increasing the mean quality time between failure (MTBF) by using OEM-specified components (when available) • Circuit boards are coded and tagged • FASTER RECOVERY: Minimize downtime with our equipment exchange program • Handling, packaging and shipping are performed in a • EXTEND PRODUCT LIFESPAN: Repair obsolete or hard to find static-free environment replacement products for increased dependability • DETAILED TESTING: Trend analysis on parts can predict component failures and enhance product reliability QUALITY MANAGEMENT • REPAIR AVOIDANCE: Component level cleaning disinfects
  • 2016 Annual Report

    2016 Annual Report

    Initiatives Responding to Change ANNUAL REPORT 2016 For the year ended March 31, 2016 Contents 2 Our History 3 Business Portfolio 4 Risks and Opportunities 6 Our Calling 8 Financial Highlights 10 Selected Financial Data 13 Stock Information 14 A Message from the Management 16 Interview with the President 26 JR East Group Management Vision V—Ever Onward: Priority Initiatives Going Forward 28 Feature: Priority Initiatives 01 Railway Network Expansion 02 Shinagawa Development Project 03 Advancement of Strategies for Visitors to Japan from Overseas 34 Review of Operations 34 Transportation > Tokyo Metropolitan Area Network, Intercity Network, and Shinkansen 37 Transportation > Railcar Manufacturing Operations 38 Non-Transportation > Station Space Utilization 0 4 Non-Transportation > Shopping Centers & Office Buildings 42 Others > Suica 44 Others > Hotel Operations / Credit Card Business 45 Column: JRE POINT / JR East Dynamic Rail Pack 46 To Achieve Sustainable Growth 46 Pursuing “Extreme Safety Levels” 49 Service Quality Reforms 50 Technological Innovation > Environment 51 Technological Innovation > Research and Development 52 Strengthening Collaboration with Local Communities 53 Tackling New Business Areas 54 Developing Employees and Creating a Corporate Culture that Maximizes Human Potential 56 Board of Directors and Corporate Auditors 58 Corporate Governance 63 Compliance 64 Organization 65 Facts and Figures 66 JR East: Domestic and International Perspectives 75 Management’s Discussion and Analysis of Financial Condition and Results of Operations 79 Operational and Other Risk Information 84 Consolidated Financial Statements 89 Notes to Consolidated Financial Statements 108 Independent Auditor’s Report 109 Glossary 110 Consolidated Subsidiaries and Equity-Method Affiliated Companies 112 Corporate Data 113 Further Information about JR East Thriving with Communities, Growing Globally The Great East Japan Earthquake poignantly reminded us of the fact that companies cannot thrive without sound and vibrant communities.