DOCSLIB.ORG

Cockpit Acceptance Check Primo Ingresso Nel Cockpit E Preparazione – PAG 1/2 1. BATTERY SWITCH

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Cockpit Acceptance Check Primo Ingresso Nel Cockpit E Preparazione – PAG 1/2 1. BATTERY SWITCH Cockpit Acceptance Check Primo Ingresso nel Cockpit e Preparazione – PAG 1/2 1. BATTERY SWITCH ..................................................................ON 2. DC Selector ……………………..…………………………………..…….BAT 3. Panel Lights..........................................................ON if required 4. GROUND POWER (If Available) ..............................................ON 5. AC Selector (if GND POWER On) …………………………...GRD PWR 6. ELECTRICAL HYDRAULIC PUMP SWITCHES (ALL) …..........OFF 7. PAX/CARGO/SERVICE DOOR LIGHT …….…….…CHECK ALL OFF 8. EMERGENCY EXIT lights switch ………...ARMED (Guard DOWN) 9. WING/ENG ANTI-ICE ………………………….…….……………….….OFF 10. EQUIP COOLINGS ……………………………….….………….…NORMAL 11. NO SMOKING / FASTEN BELTS ....…………..………………..….…ON -------------------------------------------------------------------------------------------------------------------------------------- 12. POSITION LIGHT ……………………………………………..…………………ON 13. LOGO LIGHT ………………………………. ON (Night) …………. OFF (Day) Cockpit Acceptance Check Primo Ingresso nel Cockpit e Preparazione – PAG 2/2 Prima dell’accensione dell’APU eseguire il “Test Sistemi Antincendio” Overheat/Fire Protection before APU Start 1. OVERHEAT DETECTOR SWITCHES…………………………………NORMAL 2. TEST SWITCHES …………..………Hold to FAUL/INOP then OVHT/FIRE 3. During TEST Verify: - the FAULT and WHEEL WELL lights illuminate - the FIRE HORN WILL SOUND - the THREE FIRE HANDLES WILL ILLUMINATE - the ENGINE OVERHEAT WILL ILLUMINATE -------------------------------------------------------------------------------------------------------------------------------------- Cockpit/Aircraft Preparation - Cabina ed Aeromobile - PAG 1/6 APU START 1. LEFT/RIGHT TRANSFER BUS ‘SOURCE’ LIGHTS…………………......OFF 2. LEFT/FWD FUEL PUMP…………………………………………………………..ON 3. APU START SWITCH .….…START (CHECK SWITCH GO BACK TO ON) 4. CHECK APU EGT ……………….WAIT RISE AND STABILIZED TO 400°C 5. APU GENERATOR SWITCHES ..………...ON/CHECK VOLTS (400/115V) 6. APU PNEUMATIC BLEED VALVE ……….…..ON (CHECK DUCT PRESS) 7. AC Selector …………………………………………………………………APU GEN 8. GROUND POWER ……………………………………………………………….…OFF 9. ELECTRICAL HYDRAULIC PUMP switches ……….........................ON 10. Electric Pump LOW PRESSURE lights …………..…....EXTINGUISHED 11. Check System A and B Hydraulic Pressure 2800PSI approximately Cockpit/Aircraft Preparation - Cabina ed Aeromobile - PAG 2/6 1. PARKING BRAKE ...........................................................................SET 2. FLAP LEVER .....................................................................................UP 3. SPEED BRAKE LEVER .........................................DOWN / RETRACTED 4. THRUST LEVERS .............................................………………………..IDLE 5. REVERSER ………………………………………….--……………………..CLOSED 6. START SWITCHES/FUEL FLOW ..............................……………..CUTOFF 7. STABILIZER TRIM ...............................................………GREEN RANGE 8. LANDING GEAR LEVER ..............................................................DOWN Cockpit/Aircraft Preparation - Cabina ed Aeromobile - PAG 3/6 1. IRS MODE SELECTORS ………………………………………………………..NAV 2. FLAPS/SLATS …………………………………………………………CHECK/TEST FLIGHT CONTROL PANEL CHECK: 3. ALL 5 switch guards .…………………………………………………………Down 4. ALTERNATE FLAPS position switch .…………………..…………………..Off 5. YAW DAMPER switch .………………………………………….………………..ON -------------------------------------------------------------------------------------------------------------------------------------- FUEL SYSTEM CHECK: 1. ENGINE / SPAR VALVE CLOSED lights…………...…….Illuminated Dim 2. FILTER BYPASS lights …………………………………………………………OFF 3. CROSSFEED selector ……………….……….CLOSED (Vertical Position) 4. CROSSFEED VALVE OPEN Light….…………………………………………OFF 5. FUEL PUMP switches (for tanks containing fuel) ……………..………ON 6. LOW PRESSURE lights…………………………………………………………..OFF Cockpit/Aircraft Preparation - Cabina ed Aeromobile - PAG 4/6 ELECTRICAL SYSTEM CHECK: 1. GALLEY power switch ………………………….….……………..…………..ON 2. STANDBY POWER switch …………………..……….AUTO (Guard DOWN) 3. Generator Drive DISCONNECT switches ….…...……….Guards DOWN 4. BUS TRANSFER switch ……………………………...AUTO (Guard DOWN) 5. EQUIPMENT COOLING switches .........................................NORMAL 6. OFF lights ......................................................................Extinguished 7. WINDOW HEAT switches ...........................................ON and Tested 8. PROBE HEAT switches ................................................................OFF 9. WING and ENGINE ANTI ICE switches …………….……………………OFF 10. VALVE OPEN lights ……………………………………….………Extinguished Cockpit/Aircraft Preparation - Cabina ed Aeromobile - PAG 5/6 PRESSURISATION CHECK: 1. CABIN DIFFERENTIAL PRESSURE………………………………………..ZERO CABIN ALTITUDE ……..…………………….…….……………..Field Elevation 2. CABIN RATE OF CLIMB …………………………….………………………..ZERO 3. FLIGHT ALTITUDE indicator ………………………..Set to Cruise Altitude 4. LANDING ALTITUDE ……………………..….Set to landing field elevation 5. PRESSURISATION MODE SELECTOR …………….…………………….AUTO ENGINE STARTER CHECK: 6. IGNITION SELECT switch ..................................………........IGN L or R (Set IGN on BOTH for COLD TEMPERATURES) 7. ENGINE START SWITCHES ..............................…………..................OFF Cockpit/Aircraft Preparation - Cabina ed Aeromobile - PAG 6/6 PNEUMATIC CHECK: 1. RAM DOOR FULL OPEN lights ……………………….………..ILLUMINATED 2. RECIRCULATION FAN switch ...................................……............AUTO 3. GASPER FAN ……………………………………….……………………………….ON 4. TRIM AIR ……………………………………………………………………………..ON 5. AIR CONDITIONING PACK switches ..........................................AUTO 6. ISOLATIONVALVE switch ......................................………….........OPEN 7. ENGINE BLEED AIR switches ...............................…………..............ON FLIGHT INSTRUMENTS PREPARATION – PAG 1/2 EFIS CONTROL PANEL CHECK: 1. MINIMUMS reference selector ...........................................As Desired 2. FLIGHT PATH VECTOR switch ...........................................As Desired 3. BAROMETRIC reference selector ………………………….SET Local QNH 4. VOR/ADF switches ..............................................................As Desired 5. MODE Selector ....................................................................As Desired TRAFFIC Switch .......................................................………..As Desired 6. RANGE Selector .......................................................………..As Desired CENTER switch .......................................................………...As Desired 7. MAP Switches .......................................................………….AS Desired -------------------------------------------------------------------------------------------------------------------------------------- MODE CONTROL PANEL CHECK: 1. COURSE ..........................................................……..……….SET/VERIFY 2. FLIGHT DIRECTOR switches .........................................................OFF 3. AUTOTHROTTLE switch ................................................................OFF 4. HEADING ........................................................Set to Runway Heading BANK ANGLE LIMIT switch ..........................................Set as Desired 5. ALTITUDE ..........................................Set to Takeoff Climb Clearance 6. AUTOPILOTS .....................................................................Disengaged FLIGHT INSTRUMENTS PREPARATION – PAG 2/2 7. AUTOBRAKE switch .................................................……..…….…RTO 8. AUTOBRAKE DISARM light ..........................................Extinguished 9. ANTISKID INOP light ....................................................Extinguished 10. FLAPS ……………………………………………………………………….Verify UP -------------------------------------------------------------------------------------------------------------------------------------- 1. RADIOS ..............................................................…TUNED As Required 2. TRANSPONDER ………………………………..……… Enter Code & StandBy FLIGHT MANAGEMENT COMPUTER PREPARATION – PAG 1/1 FMC/CDU SET 1. IDENT page …………................................................……………..CHECK 2. POS INIT page .........................................................…………………SET 3. RTE page ...............................................................…………………..SET Load CO-ROUTE (company route) load function or by origin/destination entry. 4. DEPARTURES page ........................................................…………..SET Select the active runway and departure/transition procedures. 5. RTE page ..........................................................……………………….SET Verify selected departure and route. Correct discontinuities. 6. ACTIVATE and EXECUTE 7. PERF INIT page .......................................................…………………SET Verify total fuel quantity is displayed on the CDU. Validate Weight Figures, Cost Index and Cruise Altitude. 8. EXECUTE. 9. N1 LIMIT page .........................................................………………..SET Enter OAT Select Desired Takeoff and Climb thrust modes 10. TAKEOFF REF page ........................................................………….SET Verify Pre Flight is complete 11. Enter takeoff flaps and V-speeds (click on 1R, 2R, 3R to populate…) ------------- Request Clearance for Pushback and Engine Start ------------- BEFORE START CHECKLIST -------------------------------------------------------------------------------------------------------------------------------------- START ENGINES Captain calls for “BEFORE START CHECKLIST First Officer Accomplishes BEFORE START
Load more

Recommended publications
  • Lighting up to 7 Times Brighter Than Other LED Landing Lights!
    Lighting FAA-PMA Approved AeroLEDs Lighting Increase safety and reduce operating cost! See the Difference... Lighting Know the Difference... • Increased safety • Direct replacement • Up to 80% reduced power consumption • Long life - over 50,000 hours! • Lighter weight - no heavy power supply - save up to 3 lbs • Reduced drag • Zero maintenance • 10x more efficient than incandescent! Increased Safety AeroLED lights allow you to comply with the latest FAA recommendations (Operation Lights On) regarding extended use of taxi, landing, and anti-collision lights without fear of reduced light performance or life. They all feature optimized light color (6500k sunlight equivalent) for proven superior air-to-air recognition. The landing and taxi lights also feature an optional pulsed recognition light mode. Reduced Power Consumption High efficiency LED lights use less than 1/3 the power of halogen bulbs. They significantly reduce the load on the electrical system and they won't dim due to low voltage, typical of low RPM final approaches when you need them most! Postition lights aerodynamic design results in less drag than original equipment! Longer Life - Zero Maintenance All AeroLED products are designed to be a "lifetime buy". They last over 50,000 hours when properly installed and do not degrade with on/off cycles. They are extremely rugged and hardened against all kinds of electrical damage, shock, and vibration. Up to 7 times brighter than other LED landing lights! PAR36 Landing Light Comparison Measured Brightness at 50 Ft. Manufacturer Intensity
    [Show full text]
  • Bell 429 Product Specifications
    BELL 429 SPECIFICATIONS BELL 429 SPECIFICATIONS Publisher’s Notice The information herein is general in nature and may vary with conditions. Individuals using this information must exercise their independent judgment in evaluating product selection and determining product appropriateness for their particular purpose and requirements. For performance data and operating limitations for any specific mission, reference must be made to the approved flight manual. Bell Helicopter Textron Inc. makes no representations or warranties, either expressed or implied, including without limitation any warranties of merchantability or fitness for a particular purpose with respect to the information set forth herein or the product(s) and service(s) to which the information refers. Accordingly, Bell Helicopter Textron Inc. will not be responsible for damages (of any kind or nature, including incidental, direct, indirect, or consequential damages) resulting from the use of or reliance on this information. Bell Helicopter Textron Inc. reserves the right to change product designs and specifications without notice. © 2019 Bell Helicopter Textron Inc. All registered trademarks are the property of their respective owners. FEBRUARY 2019 © 2019 Bell Helicopter Textron Inc. Specifications subject to change without notice. i BELL 429 SPECIFICATIONS Table of Contents Bell 429 ..................................................................................................................................1 Bell 429 Specification Summary (U.S. Units) ........................................................................4
    [Show full text]
  • Advisory Circular (AC)
    U.S. Department Advisory of Transportation Federal Aviation Administration Circular Subject: Parts 91, 121, 125, and 135 Date: 7/30/12 AC No: 120-74B Flightcrew Procedures During Taxi Initiated by: Change: Operations AFS-200/800 1. PURPOSE. This advisory circular (AC) provides guidelines for the development and implementation of standard operating procedures (SOP) for conducting safe aircraft operations during taxiing to avoid causing a runway incursion. In accordance with Federal Aviation Administration (FAA) Order 7050.1, Runway Safety Program, the definition of a runway incursion is any occurrence at an aerodrome involving the incorrect presence of an aircraft, vehicle, or person on the protected area of a surface designated for the landing and takeoff of aircraft. It is intended for use by persons operating aircraft with two or more pilots on the flight deck under Title 14 of the Code of Federal Regulations (14 CFR) parts 91, 121, 125, and 135. The FAA recommends that these guidelines become an integral part of all SOPs, flight operations manuals (FOM), and formal flightcrew member training programs. The use of flightcrew SOPs should be emphasized and employed during all phases of flight, including ground operations. Appendices 1 and 2 of this AC contain examples of SOPs that are identical or similar to some SOPs currently in use. These appendices are not directive or prescriptive in nature and do not represent a rigid FAA view of Best Practices. SOPs may vary among fleets and among certificate holders and may change over time. Operators may integrate the information contained in Appendices 1 and 2 into their fleet-specific, route-specific, and equipment-specific operations and checklists.
    [Show full text]
  • Ice and Rain Protection
    SECTION II AIRPLANE AND SYSTEMS MODEL 680 ICE AND RAIN PROTECTION The anti-ice systems are designed to prevent ice formation on the pitot tubes, static ports, angle-of-attack probes, ram air temperature (RAT) probes, engines, wings, wing roots, horizontal stabilizer leading edges, windshields, and overboard water drain lines. The vertical stabilizer does not require anti-icing. The various anti-icing systems use electrical heating elements or hot engine bleed air, and are activated by switches and knobs on the instrument panels. There are many engine instrument and crew alerting system (EICAS) messages that pertain to operation of the anti-icing systems. Some are discussed here, but most are covered in detail under Engine Indicating and Crew Alerting System (EICAS), in Section Three of this manual. ICE AND RAIN PROTECTION Figure 2-23 2-70 Configuration AA 68OM-00 SECTION II MODEL 680 AIRPLANE AND SYSTEMS ANTI-ICE CONTROL PANEL Figure 2-24 DC electric power is used to anti-ice the pitot tubes and static ports, the AOA probes, the ram air temperature (RAT) probes. AC electric power is used for the cockpit windshields and front side windows. High-pressure, or low-pressure bleed air is used to anti-ice the wing leading edges, the wing-mounted landing lights, and the horizontal stabilizer leading edges. Windshield, pitot/static and AOA anti-ice are normally operated full-time in flight. 68OM-00 Configuration AA 2-71 SECTION II AIRPLANE AND SYSTEMS MODEL 680 PITOT-STATIC AND ANGLE-OF-ATTACK (AOA) PROBE ANTI-ICE Electric elements heat the pilot and copilot pitot tubes, static ports, AOA probes, and standby pitot/static system.
    [Show full text]
  • Part 27 Instructions for Continued Airworthiness
    Part 27 Instructions for Continued Airworthiness (ICA) INCLUDING INSTALLATION INSTRUCTIONS SunSpot 36 AND 46 LANDING AND TAXI LIGHTS INSTALLED ON AIRCRAFT LISTED IN APPROVED MODEL LIST, ST-20-502-01-1 AeroLEDs, LLC 8475 W. Elisa St. Boise, ID, 83709 208-850-3294 NOTE: A printed copy of this document may not be the latest revision. It is the responsibility of the user to ensure that the latest revision is used. The latest revision of this document may be printed from the AeroLEDs electronic document repository. Revision history follows on page 2 This document contains proprietary information of AeroLEDs. Neither receipt nor possession thereof confer any right to reproduce or use, or disclose, in whole or in part, any such information without written permission from AeroLEDs. Approval Name Intent Author Ryan Edmark Check Nate Calvin Installation and Operation Instructions for the Sunspot 36 and 46 series Quality Mark McCormack lights. Date: 23 February 2021 Typed signatures indicate approval. Handwritten, Status: or electronic signature approval of this document Document Number Revision Released is on file at AeroLEDs, Boise, Idaho. 0027-0001 A 0027-0001 Part 27 Instructions for Continued Airworthiness including Installation Instructions Rev_A.docx Page 1 of 20 REVISION RECORD Rev Description Date Author IR Initial Revision 12/01/2020 R. Edmark A Updated to include Pulse Function use on lights 02/23/2021 E. Allen Please visit www.aeroleds.com to verify the revision is current. 0027-0001 Part 27 Instructions for Continued Airworthiness including Installation Instructions Rev_A.docx Page 2 of 20 TABLE OF CONTENTS System Description ....................................................................................................................................................... 4 Model Numbers ............................................................................................................................................................
    [Show full text]
  • National Transportation Safety Board Aviation Accident Final Report
    National Transportation Safety Board Aviation Accident Final Report Location: COLO SPRINGS, CO Accident Number: FTW98FA074 Date & Time: 12/21/1997, 0626 MST Registration: N100BE Aircraft: Beech A100 Aircraft Damage: Destroyed Defining Event: Injuries: 2 Fatal, 1 Serious Flight Conducted Under: Part 135: Air Taxi & Commuter - Non-scheduled Analysis The pilot was cleared for an ILS DME approach to runway 17L. During the final stage of the approach, the aircraft entered fog and disappeared from view of the control tower personnel. Radar and radio communications were lost also. After searching for 31 minutes, the aircraft was found by airport operations personnel over half way down the runway and 600 feet east of the runway. There was no evidence the aircraft touched down on the runway. The aircraft was configured with the landing gear up and the flaps deployed. Missed approach procedures require the flaps and landing gear to be retracted after initiating the procedure. The decision height for the approach is 6,384 feet msl (200 feet above ground level) and the required RVR for a 14 CFR Part 135 flight to commence and approach is 2400 (1/2 mile). When on the glide slope, the decision height is 0.4 miles from the runway touchdown zone. Examination of the airplane did not disclose evidence of mechanical malfunction.. Probable Cause and Findings The National Transportation Safety Board determines the probable cause(s) of this accident to be: Failure of the pilot to follow IFR Procedures and maintain the minimum descent altitude (MDA). A related factor was fog. Findings Occurrence #1: IN FLIGHT COLLISION WITH TERRAIN/WATER Phase of Operation: MISSED APPROACH (IFR) Findings 1.
    [Show full text]
  • Canadair Regional Jet 100/200 - Lighting
    Canadair Regional Jet 100/200 - Lighting 1. INTRODUCTION The lighting system provides interior and exterior illumination of the aircraft and consists of: Flight Compartment Lighting Passenger Compartment Lighting Service and Maintenance Lighting External Lighting Emergency Lighting. Lighting control panels for the flight compartment, passenger signs and external lighting are located in the cockpit where they are clearly visible and readily accessible to the pilot and copilot. Passenger compartment lights are controlled from the flight attendant’s panel in the forward cabin. Emergency lighting is controlled from the cockpit and may also be controlled from the flight attendant’s panel. When armed, the emergency lighting systems come on automatically if essential electrical power is lost. Service and maintenance lighting is provided for the avionics compartment, baggage compartment, aft equipment compartment and in the landing gear wheel wells. Controls for the lights are located in the area that they illuminate. Lighting system messages are displayed on the engine indication and crew alerting system (EICAS) displays. Page 1 Canadair Regional Jet 100/200 - Lighting LIGHTS FLIGHT PASSENGER SERVICE AND EXTERIOR EMERGENCY COMPARTMENT COMPARTMENT MAINTENANCE PANEL CEILING AND NOSE GEAR TAXI INTERIOR FLOODLIGHTS SIDEWALL WHEEL WELL LIGHTS AND EXTERIOR LIGHTS INTEGRAL AVIONICS LANDING DOME LIGHTS LIGHTING COMPARTMENT LIGHTS MISCELLANEOUS BOARDING AFT NAVIGATION LIGHTING LIGHTS EQUIPMENT POSITION BAY LIGHTS WING FLOOR LIGHTS GALLEY LIGHTS INSPECTION MAP READING LIGHTS LIGHTS CHART HOLDER LIGHTS STANDBY COMPASS LIGHT DOME LIGHT LAVATORY ANTI LIGHTS COLLISION LIGHTS READING BEACON LIGHTS <0021> LIGHTS ORDINANCE LOGO LIGHTS <0020> LIGHTS <MST> Page 2 Canadair Regional Jet 100/200 - Lighting 1. FLIGHT COMPARTMENT LIGHTING General illumination of the flight compartment area is provided by dome lights and floor lights.
    [Show full text]
  • Boeing 737 Checklist
    Boeing 737 Checklist PREFLIGHT CHECKLIST AFTER START CHECKS Parking Brake…………...……………………………………..………………SET Engine Generator Switches……………..……………………..…..(1 & 2) ON Battery Switch………...……………..………………………..……….……..ON APU Bleed Switch……………………………………………………….OFF Electric Hydraulic Pumps…..………………………..…………..….ON APU…………………………………….…………………………….AS NEEDED Ground Power………………………………………………CONNECT/ON Probe Heat Switches (1&2)………………………………………………………….ON Landing Gear Lever…………….………………………………..DOWN Master Caution System……..……………………….……..RECALL Engine/APU Fire Warning…..………………………………….TEST Engine and Wing Anti-Ice….………………………………..AS REQUIRED Position Lights………………………………………………………………..ON Pack Switches (Left/Right)…………………………………………………AUTO Wing Lights……………………….……………………………………..ON Isolation Valve Switch………..……………………………………..AUTO Engine Bleed Switches……………………………………………….ON Taxi Clearance…………………..………………………………OBTAIN IRS……………………………………………………..………………………NAV Transponder………………………..……………………...TA/RA (MODE C) Yaw Damper……………………………………………………………..ON Emergency Exit Lights……….………………………..……………..ARMED TAXI CHECKS Seatbelt/No Smoking Signs………………………………………………………ON Parking Brake……………………………………………………………..OFF Flap Lever………………………….……………………………………….UP Taxi Lighs………………………….…………………………………….ON Speed Brake Lever…………….………………………………………….DOWN Runway Turnoff Lights………………..…………………………………….ON Galley Switch…………………….………………………………………ON Flaps…………………………………………………………………………SET Window Heat……………………………………………………………….ON Fligth Controls………………………………………………………CHECKED Probe Heat………………………..………………………………………….OFF ACARS…………………………………..………………………………………….ON
    [Show full text]
  • Aircraft Landing Lights Enhance Runway Traffic Safety (AL2ERTS) Final Report March 2005
    Aircraft Landing Lights Enhance Runway Traffic Safety DOT/FAA/CT-TN05/18 Federal Aviation Administration William J. Hughes Technical Center Atlantic City International Airport, NJ 08405 Karen Buondonno, FAA Simulation and Analysis Group Kimberlea Bender, Titan Corporation Nicole Racine, Titan Corporation Edmundo Sierra, Titan Corporation March, 2005 DOT/FAA/CT-TN05/18 This document is available to the public through the National Technical Information Service (NTIS), Springfield, Virginia 22161. A copy is retained for reference by the William J. Hughes Technical Center IRC U.S. Department of Transportation Federal Aviation Administration NOTICE This document is disseminated under the sponsorship of the U.S. Department of Transportation in the interest of information exchange. The United States Government assumes no liability for the contents or use thereof. The United States Government does not endorse products or manufacturers. Trade or manufacturer's names appear herein solely because they are considered essential to the objective of this report. This document does not constitute FAA certification policy. Consult your local FAA aircraft certification office as to its use. This report is available at the Federal Aviation Administration William J. Hughes Technical Center’s Full-Text Technical Reports page: www.tc.faa.gov/its/act141/reportpage.html in Adobe Acrobat portable document format (PDF). Technical Report Documentation Page 1. Report No. 2. Government Accession No. 3. Recipient’s Catalog No. DOT/FAA/CT-TN05/18 4. Title and Subtitle 5. Report Date Aircraft Landing Lights Enhance Runway Traffic Safety (AL2ERTS) Final Report March 2005 6. Performing Organization Code ACB-330 7. Author(s) 8. Performing Organization Report No.
    [Show full text]
  • Bombardier Global Express - Lighting
    Bombardier Global Express - Lighting INTRODUCTION The airplane is equipped with a suite of lighting systems covering the direct and indirect illumination of the flight compartment and airplane exterior. The general airplane lighting includes: • Flight Compartment Lighting - Internal lighting is used in the flight compartment for flight instrumentation and general lighting • Passenger Compartment Lighting - Lighting systems for the passenger cabin are not provided, except for the main entrance • External Lighting - External lighting in the form of landing, taxi and airplane identification are used • Service and Maintenance Lighting - Lighting is available to service areas to assist maintenance personnel, in their airplane checks and inspections • Emergency Lighting - Lighting is provided to permit airplane occupants to safely move away from the airplane in an emergency situation DESCRIPTION FLIGHT COMPARTMENT LIGHTING Controls for the flight compartment are located on two panels on the center pedestal. One panel controls the flight compartment flood and display lighting, while the other controls the integral and miscellaneous lighting. There are two types of integral lighting in the flight compartment; electroluminescent (EL) lighting and incandescent lighting. All instrument panels are provided with integral legend/edge lighting. The instrument panels are grouped in an area, with each one having its dedicated dimming control. The electrical power to the integral lighting system is through an ON/OFF or AUTO mode selection of a MASTER switch. When in AUTO mode, to increase the life of the lighting elements (example: daylight or high cockpit light conditions) the system will be turned on or off automatically. This is accomplished through a light sensor circuit, which is dependent upon the ambient lighting conditions in the flight compartment.
    [Show full text]
  • Report Accident
    REPORT Bureau d’Enquêtes et d’Analyses pour la sécurité de l’aviation civile ACCIDENT www.bea.aero Tail strike on runway during night landing Airplane McDonnell Douglas MD-81 registered OY-KHP (1)Except where Date and time 6 February 2010 at 18h25(1) otherwise stated, the times shown in this Operator Scandinavian Airlines System (SAS) report are expressed Site of accident AD Grenoble-Isère (38) in Universal Time Public transport of passengers Coordinated (UTC). Type of flight One hour should be Unscheduled international flight added to obtain the Persons on board Captain (PNF); Co-pilot (PF); 4 PNC; 127 passengers legal time applicable in metropolitan Consequences and damage Rear part of fuselage seriously damaged France on the day of the accident. Note: this document has been translated by the BEA to make its reading easier for English speaking people. As accurate as the translation may be, the original text in French is the work of reference. 1- HISTORY OF FLIGHT The following elements are taken from FDR data and interviews. The crew took off from Copenhagen airport at 16 h 34 for Grenoble. At approximately 17 h 53, the crew began the descent for an ILS approach on runway 09. The meteorological conditions on arrival were VFR conditions, at night with an easterly wind of 8 kt. The moon was still below the horizon at the time of arrival and there was cloud cover hiding the stars, making it a particularly dark night. The runway and approach light system were set at the dimmest level. The crew was established on the localizer at approximately 10 NM from the runway threshold and had the runway in sight.
    [Show full text]
  • Getting to Grips with Cat 2 Cat 3
    Flight Operations Support & Line Assistance October 2001 CAT II / CAT III operations issue 3 II / CAT CAT getting to grips with getting to grips with CAT II / CAT III operations Flight Operations Support & Line Assistance The statements made herein do not constitute an offer. They are based on the assumptions shown and are expressed in good faith. Where the supporting grounds for these statements are not shown, the Company will be pleased to explain the basis thereof. This document is the property of Airbus and is supplied on the express condition that it is to be treated as confidential. No use of reproduction may be made thereof other than that expressely authorised. Flight Operations Support & Line Assistance and AWO Interdirectorate Group GETTING TO GRIPS WITH CATEGORY II AND III OPERATIONS STL 472.3494/95 Issue 3 October 2001 Flight Operations Support & Line Assistance and AWO Interdirectorate Group CAT II/III APPROVAL PROCESS FOREWORD The purpose of this brochure is to provide Airbus aircraft operators with the agreed interpretations of the currently applicable AWO regulations. Should any deviation appear between the information provided in this brochure and that published in the applicable AFM and MMEL, the information given in AFM and MMEL shall prevail at all times unless agreement is obtained from the national operational authorities. The brochure's objective is to provide recommendations that satisfy Category II and Category III operational and reliability requirements in order for an airline to obtain operational approval from the presiding operational authorities. All recommendations conform to the current regulatory requirements and are intended to assist the operators in maximizing the cost effectiveness of their operations.
    [Show full text]